MIC 8200 SERIES 1/4 DIN DUAL DISPLAY CONTROLLER 8 2 ORDERING OUTPUT 1 1 Relay 2 SSR Driver 3 4-20mA & Relay 4 4-20mA & SSR Driver OUTPUT 2 0 None 1 Relay 2 SSR Driver 3 4-20mA 4 4-20mA & Relay 5 4-20mA & SSR ALARM OUTPUT 0 None 1 Relay 2 SSR Driver REMOTE 0 None 1 Position Proportioning* 2 Remote Setpoint 3 RS-485 Standard Com.** 4 RS-485 Standard Com.*** 5 RS-485 Total Access Com.** 6 RS-485 Total Access Com.*** WARRANTY This instrument is backed by VOLTAGE 1 115 VAC Input & Relays the Partlow comprehensive 3 2 230 VAC Input & Relays year warranty. A complete 3 115 VAC Input warranty statement is 230 VAC Relays published in the back of the OPTION SUFFIX product instruction manual. If (See Appendix for explanation/specifications) you have further questions (Blank) None about warranties, please AB Extended Feature Software contact the Partlow factory. AD Auto Reset Adj. 0/10.00 AE AB plus Prop. Band of 9999 XP 24VDC Transmitter Power Supply ORDERING INFORMATION XA 24VDC Power Supply† For pricing and additional ordering information, refer to THE LIFEGUARD WATER-TIGHT PROTECTION ACCESSORY Form 3265, Electronic Price To order the LifeGuard, specify Part # 64417801. Book, Page 33. * Limited to Model 8211X1X or 82X22X1X. ** Output Group 2 cannot be 3, 4, or 5. *** Output Group 3 cannot be 1 or 2. † ALARM not available when XA suffix if ordered. Note: Option Suffix AB not available with RS-485 Standard Com. 34 DESCRIPTION The MIC 8200 is a 1/4 DIN, microprocessor based, dual digital display, dual setpoint, single loop, auto tune, process controller capable of controlling a variety of processes including those requiring simple on-off to dual 4-20mA outputs with full PID, while providing an operator with constant visual indication of process and setpoint. The top display may be programmed to show the process variable or deviation from setpoint. The lower display, when programmed, is keypad selectable to show setpoint 1, setpoint 2, or percent output. Options include single or dual 4-20mA output, up to three relay outputs, three types of alarms, remote setpoint input, electric motor modulation, and RS-485 communications. Process value retransmission output is also available. CONTROLLERS Access to configuration parameters and setpoint may be restricted by using the instrument's security-access mode. SPECIFICATIONS Performance Input Measurement Error Limit • Type J, K, T, E, N, C thermocouples Thermocouple types J, K, T, R, S, E, B, N, and C. and RTD +/- 0.25% of reading plus RTD 100 ohm (.00385 Ohm/Ohm/C) 1 degree at 25 C Volts 0 to 5VDC, 1 to 5 VDC Millivolts 0 to 25mVDC, 0 to 50mVDC, • Type R, S, B thermocouple 10 to 50mVDC +/- 0.25% of span at 25 C Milliamps 4 to 20mADC, accommodated via the addition of a shunt resistor • mVDC, mADC and VDC +/- 0.25% Remote Setpoint 0 to 5VDC, 1 to 5 VDC of span at 25 C Sensor Fault Detection Displays Hi or Lo for thermocouple or RTD inputs (10% above or below range) and Ambient Temperature Error 0.01% of span per degree C deviation sensor break, SnSr. On/Off outputs go off, from 25 C proportional outputs go to 0%. Sensor fault Scan Rate 1 scan per second, 3 scans available. detection is not functional for 0 to 5VDC. Display Resolution T/C & RTD: 0.01 or 1 degree mV & VDC: 0.001, 0.01, 0.1, or 1.0 Outputs Auto Reset Windup Inhibit Auto reset is disabled when the Relay SPST process is outside of the proportional 115VAC: 5.0 A Resistive; 1/8 HP or 250VA band. 230VAC: 2.5 A Resistive; 1/8HP or 250VA Cold Junction Compensation Self compensation for ambient temperature. All calibration values are SSR Driver Open collector output stored in memory. Short circuit protected at 100mA maximum Noise Rejection Normal mode, 85dB minimum at 60Hz Provides 4VDC at 20mA or 3VDC at 40mA or greater. Common mode, 90dB minimum Current Output 4-20mADC into 650 ohms maximum ±24VAC maximum for RTD input, 115VAC maximum for other inputs. Display Line Voltage 115/230VAC +/- 10% 50/60 Hz Digital Display Four 7 segment LED's each .36 inches high. Power Consumption 15VA maximum Status Indicators Individual LED indictors for Setpoint 1, Setpoint Operating Temperature 0 to 55 C, 32 to 131 F 2, Out 1, Out 2, Manual, Alarm, Degrees F, Storage Temperature -40 to 65 C, -40 to 149 F Degrees C, or Engineering Units, minus sign for Humidity 0 to 90% RH, non condensing negative values, Process Value, Percent Output Dimensions 1/4 DIN front panel, 5.8" deep 1, Percent Output 2, and Remote Setpoint. Weight 3 pounds maximum Vibration 0.5 to 100Hz at 0.5g Alarm Adjustment Process Alarm -9999 to 9999 units Agency Approvals Deviation Alarm -3000 to 3000 units UL and CSA Deviation Band Alarm 1 to 3000 units Transmitter Power Supply Control Adjustments Provides up to 40mA @ 24VDC. On/Off Hysteresis 0 to 300 units Proportional Band 1 to 3000 units Digital Communications Manual Reset -1500 to 1500 units Type RS-485 serial communication port: Auto Reset 0.0 to 100.0 repeats/minute Half-Duplex bi-directional comm. Rate 0.0 to 10.0 minutes Character Format ASCII Cycle Time 1 to 240 seconds Protocol Per ANSI X3.28 subcategories 2.5 A4 Position Prop. Sensitivity 0.0 to 50.0% Configuration User configuration to "Monitor" (read First Output Position -1000 to 1000 units only) or "Normal" (read and write) Second Output Position -1000 to 1000 units Bit Rate User configurable to 300, 600, 1200, 2400, 4800, 9600 bits per second. Address User configurable 0 to 99. 35