PM SERIES U-shaped Micro Photoelectric Sensor PNP output type available Extremely small size enables space saving and quick installation! Conforming to UL Recognition EMC Directive Extremely small Quick fitting hook-up connector Ultra-small type PM-�24(-R) contributes to the miniaturization of your equipment. Easy to maintain connector type models Even the small cable type has become very compact. are available. Its exclusive connector is the industry’s first hook-up connector. Conventional Ultra-small type Small cable type Since only crimping with exclusive pliers model PM-K24(-R) PM-K44 is to be done, cumbersome soldering or 5 mm insulation is absolutely not required. 0.197 in Further, connector attached cable is 5 mm 0.197 in also available. 26.2 mm 1.031 in 12 mm 0.472 in 22 mm 0.866 in 25.4 mm Crimp the connector Quick connection to 1.000 in on the cable. the sensor. Equipped with two independent outputs Wide model variety All models are equipped with two independent outputs�Light-ON and Dark-ON. A wide variety of 17 shapes and 34 Hence, one model suffices even if the output is to be used differently, depending models is available. You may select upon the location of use. from this wide range to suit the Also, since two independent outputs have been provided, cumbersome handling mounting conditions. of the output conversion control input, or fear of logic inversion due to a cable break, is eliminated. The sensor can be connected to the existing wiring as it is. Example of connection with a commercial intermediate connector Commercial intermediate connector Meets global requirements Conforms to Europe’s EMC Directive �V and obtains UL Recognition. 0 V Both, NPN and PNP output models are Output 1 (Light-ON) available. To PLC Output 2 (Dark-ON) Just connect the cable of the used Connected device side output (either Light-ON or Dark-ON). can be left as it is. Note: Ensure to insulate the unused output wire. 338 EQ-500 VF NX5 PM2 PM MS-AJ RT-610 PX-2 CY PHOTOELECTRIC SENSORS Multi-voltage Micro Sensor Mounting Stand Amplifier Built-in PM APPLICATIONS Sensing the starting point Determining the pallet position Sensing the starting point and overrun of a on a rotating body moving body The starting point can be Pallet is stopped by sensing the dog. Starting point and overrun is sensed using the sensed by making a slit in dog on the base. the rotating body. Overrun sensing Starting point Dog Starting point sensing Overrun sensing ORDER GUIDE Type Appearance (mm in) Sensing range Model No. (Note) Output Output operation PM-K24 6 0.236 12 22 PM-K24-R 0.472 0.866 PM-L24 12 0.472 10.5 13.4 PM-L24-R 0.413 0.528 PM-F24 10.5 0.413 Incorporated with 2 outputs: 5 mm 0.197 in NPN open-collector transistor Light-ON / Dark-ON (fixed) 12 13.4 0.472 PM-F24-R 0.528 PM-R24 10.5 0.413 12 13.4 PM-R24-R 0.472 0.528 PM-U24 6 0.236 16 13.4 0.630 PM-U24-R 0.528 Note: The suffix ‘-R’ indicates a flexible cable type. 339 Ultra-small U type R type F type L type K type Multi-voltage Micro Sensor Mounting Stand Amplifier Built-in PHOTOELECTRIC SENSORS EQ-500 VF NX5 PM2 PM MS-AJ RT-610 PX-2 CY PM ORDER GUIDE Type Appearance (mm in) Sensing range Model No. Output Output operation 7 0.276 PM-K44 NPN open-collector transistor 26.2 PM-K44P PNP open-collector transistor 25.4 1.031 1.000 13.7 0.539 NPN open-collector transistor PM-T44 26.2 PM-T44P PNP open-collector transistor 26 1.031 1.024 PM-L44 NPN open-collector transistor 15.5 0.610 PNP open-collector transistor PM-L44P 26 18.5 1.024 0.728 15.5 0.610 PM-Y44 NPN open-collector transistor 25.5 PM-Y44P PNP open-collector transistor 1.004 13.4 0.528 NPN open-collector transistor PM-F44 13.2 0.520 26.2 1.031 PM-F44P PNP open-collector transistor 13.7 0.539 13.2 0.520 NPN open-collector transistor PM-R44 26.2 PM-R44P PNP open-collector transistor 1.031 13.7 Incorporated with 0.539 5 mm 0.197 in (fixed) 2 outputs: Light-ON / Dark-ON PM-K54 NPN open-collector transistor 7 0.276 22.2 25.4 PNP open-collector transistor PM-K54P 0.874 1.000 13.7 0.539 PM-T54 NPN open-collector transistor 26 22.2 PM-T54P PNP open-collector transistor 1.024 0.874 NPN open-collector transistor PM-L54 15.5 0.610 26 PM-L54P PNP open-collector transistor 14.5 1.024 0.571 PM-Y54 NPN open-collector transistor 15.5 0.610 21.5 PNP open-collector transistor PM-Y54P 13.4 0.846 0.528 PM-F54 NPN open-collector transistor 13.2 0.520 22.2 13.7 0.874 PM-F54P PNP open-collector transistor 0.539 13.2 0.520 NPN open-collector transistor PM-R54 22.2 13.7 PM-R54P PNP open-collector transistor 0.874 0.539 340 EQ-500 VF NX5 PM2 PM MS-AJ RT-610 PX-2 CY PHOTOELECTRIC SENSORS Multi-voltage Micro Sensor Mounting Stand Amplifier Built-in Small With connector With cable R type F type Y type L type T type K type R type F type Y type L type T type K type PM ORDER GUIDE 3 m 9.843 ft cable length type 3 m 9.843 ft cable length type (standard : 1 m 3.281 ft) is also available. • Table of Model Nos. Type Standard 3 m 9.843 ft cable length type K Type PM-K24 PM-K24-C3 LType PM-L24 PM-L24-C3 F Type PM-F24 PM-F24-C3 R Type PM-R24 PM-R24-C3 U Type PM-U24 PM-U24-C3 NPN out put PM-K44 PM-K44-C3 K Type PNP out put PM-K44P PM-K44P-C3 NPN out put PM-T44 PM-T44-C3 TType PNP out put PM-T44P PM-T44P-C3 NPN out put PM-L44 PM-L44-C3 LType PNP out put PM-L44P PM-L44P-C3 NPN out put PM-Y44 PM-Y44-C3 YType PNP out put PM-Y44P PM-Y44P-C3 NPN out put PM-F44 PM-F44-C3 F Type PNP out put PM-F44P PM-F44P-C3 NPN out put PM-R44 PM-R44-C3 R Type PNP out put PM-R44P PM-R44P-C3 OPTIONS Connector Hook-up connector Designation Model No. Description • CN-14 • CN-14H • CN-14H-2 Connector CN-14 Connector for soldering This connector can be hooked-up on 0.08 to 2 0.2 mm cable simply in one grip. CN-14H Wire diameter: "0.7 to "1.2 mm "0.028 to "0.047 in Hook-up connector Suitable for UL standard cable. This connector can be hooked-up on 0.18 to 2 0.22 mm cable simply in one grip. CN-14H-2 Connector attached cable Hook-up pliers Wire diameter: "1.2 to "1.52 mm • CN-14H-C1 • CN-HP "0.047 to "0.060 in • CN-14H-C3 Length: 1 m 3.281 ft CN-14H-C1 Weight: 2 For the connector type,with 0.18 mm 20 g approx. Connector 4-core cabtyre cable Length: attached cable Cable diameter: "3.8 mm "0.150 in 3 m 9.843 ft CN-14H-C3 Weight: 60 g approx. These are exclusive pliers for hook-up Hook-up pliers CN-HP connectors CN-14H and CN-14H-2. Mounting screw • MS-M2 Mounting screw with washers for the ultra- Mounting screw MS-M2 small type sensor (50 pcs. lot). It can mount securely as it is spring washer attached. 341 Small Ultra-Small With Cable Multi-voltage Micro Sensor Mounting Stand Amplifier Built-in PHOTOELECTRIC SENSORS EQ-500 VF NX5 PM2 PM MS-AJ RT-610 PX-2 CY PM SPECIFICATIONS Ultra-small Small Type With flexible cable With cable With connector NPN output type PM-�24 PM-�24-R PM-�44 PM-�54 Model No. Item PNP output type PM-�44P PM-�54P 5 mm 0.197 in (fixed) Sensing range 0.8�1.8 mm 0.031�0.071 in opaque object Minimum sensing object Hysteresis 0.05 mm 0.002 in or less Repeatability 0.03 mm 0.001 in or less Supply voltage 5 to 24 V DC�10 % Ripple P-P 10 % or less Current consumption 15 mA or less NPN open-collector transistor PNP open-collector transistor • Maximum sink current: 50 mA • Maximum source current: 50 mA Output • Applied voltage: 30 V DC or less (between output and 0 V) • Applied voltage: 30 V DC or less (between output and�V) • Residual voltage: 0.7 V or less (at 50 mA sink current) • Residual voltage: 0.7 V or less (at 50 mA source current) 0.4 V or less (at 16 mA sink current) 0.4 V or less (at 16 mA source current) Utilization category DC-12 or DC-13 Output operation Incorporated with 2 outputs: Light-ON / Dark-ON Under light received condition: 20 !s or less Response time Under light interrupted condition: 100 !s or less (Response frequency: 1 kHz or more)(Note 1) Operation indicator Vermilion LED (lights up under light received condition) Pollution degree 3 (Industrial environment) �25 to�55 �C �13 to�131 �F (No dew condensation or icing allowed), Storage: �30 to�80 �C �22 to�176 �F Ambient temperature (Note 2, 3) Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH Ambient illuminance Fluorescent light: 1,000 ?x at the light-receiving face EMC EN 50081-2, EN 50082-2, EN 60947-5-2 Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure 50 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure Insulation resistance 10 to 2,000 Hz frequency, 1.5 mm 0.059 in amplitude in X, Y and Z directions for two hours each Vibration resistance 2 Shock resistance 15,000 m/s acceleration (1,500 G approx.) in X, Y and Z directions for three times each Emitting element Infrared LED (non-modulated) Material Enclosure: PBT, Slit cover: Polycarbonate, Terminal part [PM-�54(P) only]: Solder plated 2 2 0.09 mm 4-core cabtyre cable [PM-�24-R: 0.1 mm flexible, oil and heat resistant cabtyre Cable cable (Note 4)], 1 m 3.281 ft long 2 Extension up to total 100 m 328.084 ft is possible with 0.3 mm , or more, cable. Cable extension 10 g approx. 15 g approx. 3 g approx. Weight Notes: 1) The response frequency is the value when the disc, given in the figure below, is rotated. 1.8 mm 0.071 in Disc Disc t�0.2 mm 0.008 in 1.6 mm 0.063 in 1.6 mm 0.063 in Notes: 2) In case the ultra-small type PM-�24(-R) is used at an ambient temperature of �50 �C �122 �F, or more, make sure to mount it on a metal body. Notes: 3) Take care that the flexibility of the PM-�24-R cable is lost if the ambient temperature in near �10 �C �14 �F. Notes: 4) The cable of PM-�24-R is a flexible cable usable on a moving base. When the sensor is mounted on a moving base, fix the sensor cable joint so that stress is not applied to it. 342 EQ-500 VF NX5 PM2 PM MS-AJ RT-610 PX-2 CY PHOTOELECTRIC SENSORS Multi-voltage Micro Sensor Mounting Stand Amplifier Built-in Environmental resistance PM I/O CIRCUIT AND WIRING DIAGRAMS PM-�24 PM-�24-R NPN output type PM-�44 PM-�54 I/O circuit diagram Wiring diagram Color code for cable type (Note 2) Brown (Brown)�V Load Black ZD1 (Black) Output 1 Load Load � (Note 1,3) 5 to 24 V DC Load � �10 % 5 to 24 V DC � White 50 mA max. Tr1 �10 % (White) Output 2 (Note 1,3) � ZD2 50 mA max. Tr2 Blue (Blue) 0 V Internal circuit Users’ circuit Notes: 1) Make sure to connect terminals correctly as the sensor does not Output operation incorporate a reverse polarity protection circuit. Color code Output operation Notes: 1) Further, the output is not incorporated with a short-circuit protection circuit. Do not connect it directly to a power supply or a capacitive Output 1 Black Light-ON load. Faulty wiring may result in damage. Notes: 2) The color code of the connector attached cable is also the same. Output 2 White Dark-ON Notes: 3) Ensure to insulate the unused output wire. Symbols ... ZD1, ZD2: Surge absorption zener diode Tr1, Tr2 : NPN output transistor PM-�44P PNP output type PM-�54P I/O circuit diagram Wiring diagram Color code for cable type (Note 2) Brown (Brown)�V Black ZD1 50 mA max. � 5 to 24 V DC Tr1 � �10 % 5 to 24 V DC (Black) Output 1 (Note 1,3) � White ZD2 Load 50 mA max. �10 % � Tr2 Load Load (White) Output 2 (Note 1,3) Load Blue (Blue) 0 V Internal circuit Users’ circuit Notes: 1) Make sure to connect terminals correctly as the sensor does not Output operation incorporate a reverse polarity protection circuit. Notes: 1) Further, the output is not incorporated with a short-circuit protection Color code Output operation circuit. Do not connect it directly to a power supply or a capacitive Output 1 Black Light-ON load. Faulty wiring may result in damage. Notes: 2) The color code of the connector attached cable is also the same. Output 2 White Dark-ON Notes: 3) Ensure to insulate the unused output wire. Symbols ... ZD1, ZD2: Surge absorption zener diode Tr1, Tr2 : PNP output transistor SENSING CHARACTERISTICS (TYPICAL) PM-�44(P) PM-24�(-R) Ultra small type Small type PM-�54(P) Sensing position Sensing position Dark- Dark- Dark- Dark- 5.5 mm ON ON 0.217 in ON ON # 7 mm 8.5 mm 0.276 in 6 mm 0.335 in 0.236 in # # # 2 mm 2.9 mm 0.079 in 0.114 in Beam Beam axis axis Light- Light- Light- Light- ON ON ON ON 012 3 4 012 3 4 012 3 4 012 3 4 0.039 0.079 0.118 0.157 0.039 0.079 0.118 0.157 0.039 0.079 0.118 0.157 0.039 0.079 0.118 0.157 Operating point # (mm in) Operating point # (mm in) Operating point # (mm in) Operating point # (mm in) 343 Sensor circuit Sensor circuit Multi-voltage Micro Sensor Mounting Stand Amplifier Built-in PHOTOELECTRIC SENSORS EQ-500 VF NX5 PM2 PM MS-AJ RT-610 PX-2 CY PM PRECAUTIONS FOR PROPER USE Refer to p.1135l for general precautions. All models Cable extension This product is not a safety sensor. Its use is not intended or designed to protect life and prevent body • Cable extension is possible up to an overall length of 100 m 2 injury or property damage from dangerous parts of 328.084 ft with a 0.3 mm , or more, cable. However, since machinery. It is a normal object detection sensor. a voltage drop shall occur due to the cable extension, ensure that the power supply voltage at the end of the cable attached to the sensor or at the sensor terminals is Make sure to connect terminals correctly as the within the rating. sensor does not incorporate a reverse polarity protection circuit. Further, the output is not incorporated with a short- Total cable length 100 m 328.084ft circuit protection circuit. Do not connect it directly to Cable attached a power supply or a capacitive load. Faulty wiring to sensor or con- �V nector terminals Extension cable may result in damage. � Output 5 to 24 V DC �10 % � 0 V Others • Since the sensor is intended for use Supply voltage: 4.5 V or more inside machines, no special counter- measures have been taken against • But, when the overall cable length, including the cable extraneous light. Take care that extra- attached to the sensor, is as given below, there is no need neous light is not directly incident on to confirm the voltage. the beam receiving section. Conductor cross-section area Total cable length • Do not use during the initial transient time (50 ms) after the power supply is switched on. 2 0.08 to 0.1 mm Up to 5 m 16.404 ft • The cable of PM-�24-R is a flexible cable usable on a 2 0.2 mm Up to 10 m 32.808 ft moving base. When the sensor is mounted on a moving 2 0.3 mm Up to 20 m 65.617 ft base, fix the sensor cable joint so that stress is not applied to it. • Take care that the flexibility of the PM-�24-R cable is lost if the ambient temperature is near �10 �C �14 �F. Mounting • When fixing the sensor with screws, use M3 screws [M2 screws in case of PM-�24(-R)] and the tightening torque should not exceed the values given below. Further, use small, round type plain washers. (M3: "6 mm "0.236 in, M2: "4.3 mm "0.169 in) M3 screws Model No. Tightening torque M2 screws in [ ] case of PM-�24(-R) 0.15 N�m PM-�24(-R) Spring washer PM-�44(P) Plain washer 00.5 N�m Outer diameter PM-�54(P) M3: "6 mm "0.236 in Note: In case the ultra-small type M2: "4.3 mm ( ) "0.169 in PM-� 24(-R) is used at an ambient temperature of�50 �C �122 �F, or more, make sure to mount it on a metal body. 344 EQ-500 VF NX5 PM2 PM MS-AJ RT-610 PX-2 CY PHOTOELECTRIC SENSORS Multi-voltage Micro Sensor Mounting Stand Amplifier Built-in PM PRECAUTIONS FOR PROPER USE Refer to p.1135l for general precautions. PM-�54 PM-�54P Cautions in plugging or unplugging a connector Crimping method 1 Strip the cable sheath 15 mm 0.591 in, or more, and insert the • Do not plug or unplug a connector more than 10 wires into the connector insertion holes till the wire tips reach times. the end. • Be sure not to give stress more than 5 N to a ter- minal of both a connector and a sensor. Lead wire If you do not follow the above cautions, it will (Do not strip the wire insulation.) cause a poor contact. Cable sheath 15 mm 0.591 in or more Procedures of plugging or unplugging a connector 1 Insert a connector straight into a Hook Arrangement of connector terminals sensor until the connector lug is Lug locked by the sensor hook. �V: �V �V1122 00VV 1: Output 1 (Light-ON) (Note) Power supply 2: Output 2 (Dark-ON) 0 V : 0 V Note: Wire at Pin No.1 or 2 as per requirement. 5 N or less 2 When unplugging, give as much 2 Crimp with the exclusive stress as a connector lug can be hook-up pliers CN-HP. relieved from a hook. Then unplug it. Notes: 1) When attaching or detach- ing the connector fitted with a cable, make sure to hold the connector firmly before proceeding. Caution: Be sure to hold a connector Notes: 2) After crimping, do not pull when plugging or unplugging on the cable. it. Do not hold a terminal or a cable when plugging or unplugging the connector. Caution: Make sure to use the exclusive hook-up pliers CN-HP. Otherwise, it will cause a Commercially available pliers cannot be used. poor contact. • Prior to using the sensor, affix the cable in a way as to Crimping of hook-up connectors CN-14H and CN-14H-2 avoid direct stress on the crimped part. Model No. CN-14H CN-14H-2 Item Cable diameter Wire diameter 2 2 Conductor cross- 0.08 to 0.2 mm 0.18 to 0.22 mm section area (AWG28 to AWG24) (AWG25 to AWG24) "0.7 to "1.2 mm "1.2 to "1.52 mm Wire diameter "0.028 to "0.047 in "0.047 to "0.060 in Conductor cross-section area Soldering (Both connector CN-14 and sensor) Wire insulation Vinyl chloride or soft poly- material ethylene • If soldering is done directly on the terminals, strictly adhere to the conditions given below. Soldering temperature 260 �C 500 �F or less Soldering time 3 sec. or less Soldering position Refer to the below figure Sensor Connector 1.5 mm 0.059 in �V1 2 0 V �V1 2 0 V Soldering position 345 Multi-voltage Micro Sensor Mounting Stand Amplifier Built-in PHOTOELECTRIC SENSORS EQ-500 VF NX5 PM2 PM MS-AJ RT-610 PX-2 CY PM DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ PM-K24 PM-L24 Sensor Sensor PM-K24-R PM-L24-R 3 3 0.118 0.118 6 Beam axis Beam axis 10.5 0.236 5.5 0.217 0.413 13.4 "2.7 "0.106 cable, 1 m 3.281 ft long 0.528 2 5.5 5 0.079 8 0.217 0.197 0.315 2-"2.5 "0.098 mounting holes Beam axis 12 8 13.4 0.472 0.315 6 4 0.157 0.528 0.236 5 0.197 2-"2.5 "0.098 "2.7 "0.106 cable, 2 mounting holes 1 m 3.281 ft long Beam axis 5.5 0.217 0.079 12 Operation indicator 10 0.394 0.472 "4.8 (Vermilion) 4 0.157 "0.189 Operation indicator 18 0.709 2 (Vermilion) 22 0.866 0.079 PM-F24 PM-R24 Sensor Sensor PM-F24-R PM-R24-R Beam axis Beam axis 4 4 0.157 0.157 6.7 6.7 0.264 0.264 10.5 10.5 0.413 13.4 0.413 1.5 0.059 6 13.4 0.528 1.5 0.059 6 0.528 0.236 5.5 5 3 5.5 2 0.236 2 5 0.197 5.5 3 0.217 0.118 0.217 0.079 0.197 0.079 0.217 0.118 Beam axis Beam axis 5.5 0.217 8 12 8 12 0.315 0.472 0.315 0.472 4 0.157 4 0.157 Operation indicator (Vermilion) "2 Operation indicator "2 "2.7 "0.106 cable, 2 "0.079 2 (Vermilion) "0.079 0.079 1 m 3.281 ft long 0.079 "4.8 "2.5 "0.098 mounting hole "4.8 "2.5 "0.098 mounting hole "0.189 "0.189 "2.7 "0.106 cable, 1 m 3.281 ft long PM-U24 PM-K44 Sensor Sensor PM-U24-R PM-K44P 25.4 1.000 3 3.5 0.138 0.118 19 0.748 7 6 Beam axis Beam axis 0.276 0.236 2-"3.2 "0.126 mounting holes Operation indicator 19 0.748 (Vermilion) 13.4 0.528 5 6.4 13.4 2.9 0.114 0.197 0.252 0.528 1 0.039 2 5 Beam axis 0.079 0.197 8.5 0.335 13.8 0.543 Beam axis 5.5 0.217 26.2 1.031 16 12 11 0.630 0.472 0.433 10.8 9.5 0.374 0.425 Operation indicator (Vermilion) 2-"3.8 "0.150 4 mounting holes 2 0.157 0.079 8 "2.7 "0.106 cable, 1 m 3.281 ft long "4.8 0.315 "0.189 "2.7 "0.106 cable, 1 m 3.281 ft long 2-"2.5 "0.098 mounting holes 346 EQ-500 VF NX5 PM2 PM MS-AJ RT-610 PX-2 CY PHOTOELECTRIC SENSORS Multi-voltage Micro Sensor Mounting Stand Amplifier Built-in PM DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ PM-T44 PM-L44 Sensor Sensor PM-T44P PM-L44P 13.7 26 1.024 0.539 3.2 19 0.748 7 0.276 4-R2 0.126 1 0.039 3 0.118 7 Beam axis 0.276 18.5 6.4 2-mounting oblong holes 0.728 10.8 Beam axis 0.252 0.425 Operation indicator (Vermilion) 2 "4.8 13.4 0.528 "2.7 "0.106 cable, 1 m 3.281 ft long 0.079 26 "0.189 5 13.4 1.024 1 0.197 2.9 0.114 0.528 0.039 4.3 2.9 13.4 0.528 0.169 6.4 Beam axis 0.114 8.5 0.335 5 0.252 3.2 0.197 13 0.126 0.512 26.2 Beam axis 3.3 8.5 0.335 6.2 1.031 15.5 0.130 9 0.354 0.244 0.610 10.8 10.3 7.2 6.5 Operation indicator 0.425 0.406 0.283 0.256 (Vermilion) 2.5 19 3.6 0.098 0.748 2 0.142 "2.7 "0.106 cable, 2-"3.2 "0.126 mounting holes 0.079 "4.8 2-mounting 1 m 3.281 ft long 19 "0.189 oblong holes 0.748 PM-Y44 PM-F44 Sensor Sensor PM-Y44P PM-F44P 7 Beam axis 2-"3.5 "0.138 mounting holes 0.276 1 0.039 2.5 3.5 0.138 0.098 7 7 0.276 0.276 13.7 13.2 Beam axis 0.539 25.5 0.520 1.004 13.4 0.528 6.4 15 10.8 5 0.252 0.591 2.9 3.2 0.425 0.197 7 1 0.114 0.126 0.276 0.039 9 Operation indicator 0.354 Beam axis 8.5 (Vermilion) 0.335 2 "4.8 "2.7 "0.106 cable, 1 m 3.281 ft long 0.079 "0.189 26.2 7 13.6 13.4 0.528 6.4 1.031 0.276 2.9 0.114 0.535 5 0.252 10.8 0.197 3.3 0.130 0.425 4 0.157 8.5 Beam axis 2.5 0.335 15.5 12.6 0.098 0.610 2 0.079 0.496 6.5 Operation indicator 0.256 "4.8 (Vermilion) 2-"3.5 "0.138 mounting holes "0.189 3.3 "2.7 "0.106 cable, 1 m 3.281 ft long 0.130 PM-R44 PM-K54 Sensor Sensor PM-R44P PM-K54P 25.4 1.000 Beam axis 3.5 0.138 19 0.748 2.5 7 Beam axis 0.098 0.276 7 0.276 13.7 0.539 2-"3.2 "0.126 mounting holes 13.2 0.520 13.4 0.528 6.4 Operation indicator 19 0.748 2.9 5 0.252 3.2 (Vermilion) 0.197 7 0.114 13.4 0.528 1 0.126 6.4 0.276 5 0.197 2.9 0.114 0.039 0.252 1 0.039 8.5 Beam axis 9 0.335 8.5 Beam axis 0.354 0.335 13.8 26.2 22.2 7 13.6 0.543 1.031 0.874 0.276 0.535 11 10.8 6.8 3.3 0.130 0.433 0.425 5.5 0.217 0.268 4 0.157 5 0.197 2 2-"3.8 "0.150 mounting holes 2-"3.5 "0.138 0.079 "2.7 "0.106 cable, mounting holes "4.8 1 m 3.281 ft long "0.189 Operation indicator (Vermilion) 347 Multi-voltage Micro Sensor Mounting Stand Amplifier Built-in PHOTOELECTRIC SENSORS EQ-500 VF NX5 PM2 PM MS-AJ RT-610 PX-2 CY PM DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ PM-T54 PM-L54 Sensor Sensor PM-T54P PM-L54P 13.7 0.539 26 1.024 7 0.276 19 0.748 3.2 3 4-R2 R0.079 0.126 1 0.039 0.118 7 Beam axis 0.276 14.5 0.571 6.4 6.8 2-mounting oblong holes Beam axis 0.252 0.268 Operation indicator (Vermilion) 13.4 5 0.528 13.4 0.528 0.197 5 2.9 0.197 26 1 0.114 1.024 0.039 13.4 0.528 2.9 5 6.4 4.3 0.114 0.197 Beam axis 0.252 0.169 8.5 0.335 3.2 13 Beam axis 0.126 22.2 8.5 0.335 0.512 15.5 0.874 9 0.354 6.2 0.610 7.2 6.5 0.244 6.3 6.8 Operation indicator 0.283 0.256 0.248 0.268 (Vermilion) 5 0.197 19 3.6 3.3 2.5 0.748 0.142 0.130 0.098 19 2-"3.2 "0.126 mounting holes 2-mounting oblong holes 0.748 PM-Y54 PM-F54 Sensor Sensor PM-Y54P PM-F54P 2-"3.5 "0.138 mounting holes 7 Beam axis 0.276 1 0.039 3.5 0.138 2.5 0.098 7 7 0.276 0.276 21.5 Beam axis 0.846 13.7 11 6.8 0.539 0.433 0.268 13.2 5 0.197 Operation indicator 13.4 0.520 (Vermilion) 0.528 6.4 5 0.252 2.9 3.2 0.197 1 0.114 7 13.4 0.126 0.276 0.039 0.528 6.4 2.9 Beam axis 8.5 5 0.252 0.114 0.197 0.335 9 0.354 22.2 8.5 Beam axis 0.874 13.6 7 2.5 0.335 15.5 6.8 0.535 0.276 12.6 0.098 0.610 0.268 0.496 6.5 3.3 0.130 0.256 5 0.197 3.3 Operation indicator 0.130 (Vermilion) 2-"3.5 "0.138 mounting holes PM-R54 Sensor mTerminal part (PM-�54, PM-�54P) PM-R54P �V1 2 0 V Beam axis 1 1 0.039 0.039 2.5 0.098 7 1.3 0.8 0.276 t 0.3 0.051 0.031 2.1 13.7 t 0.012 1.6 0.083 0.539 0.063 2.54 2.54 2.54 13.4 0.528 0.100 0.100 0.100 13.2 0.520 5 2.9 6.4 0.197 1 0.114 0.252 3.2 0.039 7 0.126 0.276 8.5 Beam axis 0.335 9 0.354 22.2 0.874 7 13.6 0.276 0.535 6.8 0.268 3.3 0.130 5 0.197 Operation indicator 2-"3.5 "0.138 mounting holes (Vermilion) 348 EQ-500 VF NX5 PM2 PM MS-AJ RT-610 PX-2 CY PHOTOELECTRIC SENSORS Multi-voltage Micro Sensor Mounting Stand Amplifier Built-in PM DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ CN-14H CN-14 Connector (Optional) Hook-up connector (Optional) CN-14H-2 4.6 13 13 0.181 0.512 0.512 1 0.039 7.5 CN-14 CN-14H 0.295 0 V 2 1 �V �V 1 2 0 V 1 1 �V1 20 V 15 0.039 0.039 0.591 (5) (0.197) 0 V 2 1 �V t 0.4 t 0.016 0.8 0.031 6 2 0.079 1.6 0.063 0.236 6 0.236 (2.54)(0.100) (7.62) (0.300) �V1 2 0V CN-14H-C1 Connector attached cable (Optional) CN-14H-C3 L (50) 15 (1.969) 0.591 (8) (0.315) 13 0.512 6 0.236 "3.8 "0.150 cable • Cable length L Model No. Cable length CN-14H-C1 1 m 3.281 ft CN-14H-C3 3 m 9.843 ft 349 CN-14H �V1 2 0V Multi-voltage Micro Sensor Mounting Stand Amplifier Built-in PHOTOELECTRIC SENSORS EQ-500 VF NX5 PM2 PM MS-AJ RT-610 PX-2 CY