LH-50 SERIES LED Type Optical Displacement Sensor Minute displacements measured with high precision by red �� � LED beam Conforming to UL Recognition EMC Directive Safety precautions unnecessary Reducing total cost Compact and lightweight The light source uses a red LED for The high-functional controller includes Sensor head safety. built-in calculation and measurement Compared to our previous sensors, the As a result, the complicated safety functions, so that the digital panel LH-50 series sensors are much more measures which are necessary when controller which was needed previously compact and lightweight, so that they using laser light are completely is no longer required, thus reducing can easily be installed even in tight unnecessary. costs. spaces. Even though a In addition, it also helps to reduce 24 mm red LED is used, wiring and space costs. 72 mm 0.945 in the degree of 2.835 in 17 mm 46 mm 0.669 in 1.811 in performance achieved is the 46 mm Not 1.811 in 75 mm same as for needed 2.953 in laser-type sen- sor class (Class Optical shield LH-50 series 1 to 2), so that Previous product high-precision Laser-type displacement measurement is sensor Not needed Controller possible. The general purpose controller is the Digital panel controller LH-CS6(P) most compact in its class. Furthermore, the high-functional Universal use controller is a �48 mm �1.890 in panel mounting type which can be The LH-50 series complies with EMC mounted on equipment panels. directive for the CE marking. 67 mm It uses an LED beam which is not 2.638 in subject to FDA restrictions. In addition, it obtains UL recognition. 40 mm 1.575 in 26 mm 1.024 in General purpose controller (DIN rail mounting type) UL Recognition 77.5 mm Conforming to EMC Directive 3.051 in 48 mm 1.890 in 48 mm 1.890 in High-functional controller Panel mounting (Panel mounting type) 904 GP-A GP-X LD LA LA-300 HL-T1 LM10 LH-50 HL-C1 MEASUREMENT SENSORS Magnetic Displacement Light / Thru-beam Type Light / Reflective Type LH-50 Simple and useful • Uses an easy-to-operate jog switch • Full range of ‘ready-to-use’ and ‘useful’ functions General purpose controller High-functional controller Threshold value settings and other The high-functional controller is equipped with useful Press settings can be made easily using the calculation functions, so that the digital panel controller Turn extremely easy-to-operate jog switch. which was needed previously is no longer required. Furthermore, the settings and measurement values are indicated in a 5-digit LED display. 5-digit LED display examples Digital panel controller not (Example of measurement value) (Example of settings) needed LH-CD6(P) Digital panel controller • Flexible combinations Calculation, level difference and thickness measurements and Sensor head General purpose controller High-functional controller displacement from the measuring center when using a single The LH-50 series can be used in any combination desired. sensor head are set to default settings, so that the unit can be In addition, the sensor head and controller need not be used immediately. managed as a pair. Level difference measurement (A B) Thickness measurement L – (A�B) � Moreover, the LH-CD6(P) high-functional controller can be connected to two sensor heads of different types. L Select by center measuring AB distance and measuring range ... General purpose AB 40 mm controller Level difference 1.575 in LH-CL6(P) type sensor head LH-54 High-functional Thickness controller (1ch) LH-CS6(P) 80 mm 3.150 in type sensor High-functional head LH-58 • Response time & resolution settings to suit the application controller (2ch) LH-CD6(P) General purpose controller High-functional controller 120 mm 4.724 in Both the general purpose controller and the high-functional type sensor controller let you select the response time from one of eight head LH-512 settings. (The high-functional controller also allows automatic response time setting.) Conventional displacement sensors generally provided three settings, but the LH-50 series (8 settings) provides • Automatic response time setting much greater flexibility for response time and resolution. High-functional controller This device allows a highly accurate analog output suited for any application. The LH-CS6(P) and LH-CD6(P) high-functional controllers are equipped with an automatic response time setting Conventional (example) LH-50 series function. This function sets the response time automatically in �Response time / Resolution (2 σ) accordance with the object’s speed of movement. It ensures Sensor head accurate measurement even for variable line speeds. Model No. In addition, it eliminates the burden of having to set the LH-54 LH-58 LH-512 Controller response time response time. Priority to 2 !m 4 !m 20 !m 300 ms resolution 0.079 mil 0.157 mil 0.787 mil 4 !m 8 !m 40 !m 100 ms 0.157 mil 0.315 mil 1.575 mil 5 !m 14 !m 65 !m 40 ms If the line speed If the line speed 0.197 mil 0.551 mil 2.559 mil RESPONSE becomes faster ... OK becomes slower ... OK 6 !m 16 !m 75 !m Fast 30 ms 0.236 mil 0.630 mil 2.953 mil Medium 7 !m 28 !m 92 !m Slow 20 ms 0.276 mil 1.102 mil 3.622 mil 10 !m 40 !m 130 !m 10 ms 0.394 mil 1.575 mil 5.118 mil 20 !m 120 !m 400 !m 1 ms 0.787 mil 4.724 mil 15.748 mil Priority to 40 !m 160 !m 580 !m 0.5 ms response 1.575 mil 6.299 mil 22.835 mil 905 Magnetic Displacement Light / Thru-beam Type Light / Reflective Type MEASUREMENT SENSORS GP-A GP-X LD LA LA-300 HL-T1 LM10 LH-50 HL-C1 LH-50 Simple and useful • AUTO gain setting, SELECT gain setting General purpose controller High-functional controller Two types of gain control are provided: AUTO and SELECT (11 settings), to provide great flexibility for a variety of applications. Furthermore, a 7-segment display is used to indicate whether the gain is set to the optimum level. AUTO gain setting: For objects with highly variable color and materials AUTO gain setting This setting automatically controls the gain so that the incident ensures accuracy light intensity is optimized to handle variations in the reflection even for patterned ratios (variations in the amount of light received) for the objects measured objects. It is suitable for objects which produce large variations in reflection ratios. Note: Some fluctuation in resolution and linearity may occur when this setting is used. SELECT gain setting: For more accurate measurement using the optimum gain This function lets you set the gain to match the reflection ratio for the measured object. An incoming light status bar (general purpose controller) is provided to assist with setting the gain to the optimum level. BRI. GOOD DAR. BRI. GOOD DAR. BRI. GOOD DAR. BRI. GOOD DAR. BRI. GOOD DAR. Incident Large light Small intensity m The illustrations show the display for general purpose controllers. High-functional controllers are also provided with AUTO gain and SELECT gain settings. • Analog output hold function General purpose controller High-functional controller If momentary underexposure (DARK) or overexposure (BRIGHT) conditions occur, the value is held at the level immediately before this occurs. It allows measurement to continue without any breaks in analog output. Measured object Analog output waveform Momentary underexposure (DARK) ON Alarm output OFF 906 GP-A GP-X LD LA LA-300 HL-T1 LM10 LH-50 HL-C1 MEASUREMENT SENSORS Magnetic Displacement Light / Thru-beam Type Light / Reflective Type LH-50 Simple and useful • 16 types of setting storage memory • Two-in-one functionality High-functional controller General purpose controller The LH-CS6(P) and LH-CD6(P) high-functional controllers The LH-CL6(P) general purpose controller has two inde- have 16 types of built-in setting storage memory to provide pendent comparison outputs, making it suitable for use in greater flexibility for production lines where the model applications where two sensor units were previously required. variety frequently changes. Example: Measurement of products with variable heights and Example: Dimension checking after press-fitting, separation of good / bad judgment defective items Incomplete press-fitting OK OK Press-fitting missed Comparative ON Set value 1 Set value 2 Set value 3 Press-fitting missed output 1 (FAR ON setting) 30 mm�0.5 mm 25 mm�0.3 mm 35 mm�0.8 mm OFF 1.181 in�0.020 in 0.984 in�0.012 in 1.378 in�0.031 in ON Comparative Incomplete press-fitting output 2 (NEAR ON setting) OFF APPLICATIONS Work seating confirmation Pipe exterior distortion detection Measuring wheel eccentricity LH-58 LH-512 LH-58 907 Magnetic Displacement Light / Thru-beam Type Light / Reflective Type MEASUREMENT SENSORS GP-A GP-X LD LA LA-300 HL-T1 LM10 LH-50 HL-C1 LH-50 ORDER GUIDE Sensor heads Spot diameter Resolution Type Appearance Measurement center distance Model No. (Note 1) (Note 2) "1.6 mm "0.063 in 2 !m LH-54 40 mm 1.575 in or less 0.079 mil (Measuring range �10 mm �0.394 in) "2.0 mm "0.079 in 4 !m LH-58 80 mm 3.150 in or less 0.157 mil (Measuring range �20 mm �0.787 in) "3.0 mm "0.118 in 20 !m LH-512 120 mm 4.724 in or less 0.787 mil (Measuring range �30 mm �1.181 in) 2 Notes: 1) The spot diameter is a typical value for the measurement center distance given, and is based on the definition of 1/e (13.5 %) of the beam axis intensity. 2) The resolution values were obtained under the following measurement conditions. 24 V DC supply voltage, �20 ˚C �68 ˚F ambient temperature, SELECT gain setting, 300 ms response time setting, measurement center distance, interference prevention function not used and white ceramic board object, set to 2 σ. Controllers Type Appearance Model No. Comparative output No. of sensor heads connected NPN open-collector transistor LH-CL6 (OUT1, OUT2) 1 No. PNP open-collector transistor LH-CL6P (OUT1, OUT2) NPN open-collector transistor LH-CS6 (HI, GO, LO) 1 No. PNP open-collector transistor LH-CS6P (HI, GO, LO) NPN open-collector transistor LH-CD6 (HI, GO, LO) The photo shows 1 No. or 2 Nos. PNP open-collector transistor the LH-CD6 LH-CD6P (HI, GO, LO) OPTIONS Accessory • MS-DIN-3 Designation Model No. Description Mounting bracket for ( general purpose controller Length: 2 m 6.562 ft LH-CCJ2 Weight: 130 g approx. 2 0.22 mm cabtyre cable, with connector on both ends Length: 5 m 16.404 ft Extension cable • Cable outer diameter: "6 mm "0.236 in LH-CCJ5 Weight: 270 g approx. • Connector outer diameter: "14.7 mm "0.579 in max. Length: 10 m 32.808 ft LH-CCJ10 Weight: 480 g approx. Extension cable • LH-CCJ2 Length • LH-CCJ5 • LH-CCJ10 908 GP-A GP-X LD LA LA-300 HL-T1 LM10 LH-50 HL-C1 MEASUREMENT SENSORS Magnetic Displacement Light / Thru-beam Type Light / Reflective Type 120 mm 4.724 in 80 mm 3.150 in 40 mm 1.575 in High-functional General purpose type type type ( LH-50 SPECIFICATIONS Please refer to the separate ‘User’s Manual’ for more details pertaining to specifications. (Refer to p.916) Sensor heads Type 40 mm 1.575 in type 80 mm 3.150 in type 120 mm 4.724 in type Item Model No. LH-54 LH-58 LH-512 Applicable controller LH-CL6(P), LH-CS6(P), LH-CD6(P) Measurement center distance 40 mm 1.575 in 80 mm 3.150 in 120 mm 4.724 in �10 mm (30 to 50 mm) �20 mm (60 to 100 mm) �30 mm (90 to 150 mm) Measuring range �0.394 in (1.181 to 1.969 in) �0.787 in (2.362 to 3.937 in) �1.181 in (3.543 to 5.906 in) Emitting element Red LED (modulated)(Peak wavelength: 650 nm 0.026 mil) Spot diameter (Note 2) "1.6 mm "0.063 in or less "2.0 mm "0.079 in or less "3.0 mm "0.018 in or less 300 ms 02 !m 0.079 mil 004 !m 0.157 mil 020 !m 00.787 mil 100 ms 04 !m 0.157 mil 008 !m 0.315 mil 040 !m 01.575 mil 40 ms 05 !m 0.197 mil 014 !m 0.551 mil 065 !m 02.559 mil 30 ms 06 !m 0.236 mil 016 !m 0.630 mil 075 !m 02.953 mil Resolution (Note 3) 20 ms 07 !m 0.276 mil 028 !m 1.102 mil 092 !m 03.622 mil 10 ms 10 !m 0.394 mil 040 !m 1.575 mil 130 !m 05.118 mil 1 ms 20 !m 0.787 mil 120 !m 4.724 mil 400 !m 15.748 mil 0.5 ms 40 !m 1.575 mil 160 !m 6.299 mil 580 !m 22.835 mil Linearity (Note 4) Within�0.2 % F.S. Ambient temperature 0 to�45 °C �32 to�113 °F (No dew condensation), Storage:�20 to�60 °C �4 to�140 °F Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH Protection (excluding connector part) IP67 (IEC) 2 Cable 0.22 mm 11-core composite cabtyre cable, 0.2 m 0.656 ft long, with a connector at the end Cable extension Extension up to total 10.2 m 33.465 ft is possible, with optional cable Weight 70 g approx. (including cable), 45 g approx. (excluding cable) Notes: 1) Conditions which have not been specified are to be taken as: 24 V DC supply voltage,�20 °C �68 °F ambient temperature, SELECT gain setting, 300 ms response time setting, measurement center distance, interference prevention function not used and white ceramic board object. 2 Notes: 2) This is the value at the measurement center distance, and is based on the definition of 1/e (13.5 %) of the beam axis light intensity. Take care that some amount of light spreads out of the specified spot diameter and, depending on the conditions around the measured object, may affect the measurement accuracy. Notes: 3) This is the typical value at the measurement center distance for a white ceramic board object. The given values are for the analog output of the applicable controller. Notes: 4) This is the value for white ceramic board object. The linearity may differ depending on the measured object. The given value is for the analog output of the applicable controller. 909 Controller response time Magnetic Displacement Light / Thru-beam Type Light / Reflective Type MEASUREMENT SENSORS GP-A GP-X LD LA LA-300 HL-T1 LM10 LH-50 HL-C1 LH-50 SPECIFICATIONS Please refer to the separate ‘User’s Manual’ for more details pertaining to specifications. (Refer to p.916) Controllers General purpose Type NPN output PNP output Item Model No. LH-CL6 LH-CL6P Applicable sensor head LH-54, LH-58, LH-512 Connectable sensor heads (Max.) 1 No. Supply voltage 24 V DC�10 % Ripple P-P 10 % or less Current consumption (Note 2) 250 mA or less Analog voltage Analog current Analog output • Output voltage:�5 to�5 V/F.S. • Output current: 4 to 20 mA/F.S. • Output impedance: 100 Ω • Load resistance: 300 Ω or less Response time (10 to 90 %) 0.5 ms / 1 ms / 10 ms / 20 ms / 30 ms / 40 ms / 100 ms / 300 ms selectable by jog switch Temperature characteristics Within �0.04 % F.S./°C Span adjustment / Shift adjustment Within �10 % F.S. (Note 2) Independence two outputs (OUT1, OUT2) Independence two outputs (OUT1, OUT2) NPN open-collector transistor PNP open-collector transistor • Maximum sink current: 100 mA • Maximum source current: 100 mA Comparative output • Applied voltage: 30 V DC or less • Applied voltage: 30 V DC or less (between comparative output and 0 V) (between comparative output and �V) • Residual voltage: 1.5 V or less (at 100 mA sink current) • Residual voltage: 1.5 V or less (at 100 mA source current) 0.4 V or less (at 16 mA sink current) 0.4 V or less (at 16 mA source current) Output operation ON or OFF when threshold level is reached (selectable by jog switch) Short-circuit protection Incorporated Alarm output Incorporated Ambient temperature 0 to�50 °C �32 to�122 °F (No dew condensation), Storage: �20 to�60 °C �4 to�140 °F Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH 2 Cable 0.22 mm 13-core composite cabtyre cable, 2 m 6.562 ft long. Weight 160 g approx. Accessory MS-DIN-3 (Controller mounting bracket): 1 pc. Notes: 1) Conditions which have not been specified are to be taken as: 24 V DC supply voltage,�20 °C �68 °F ambient temperature, SELECT gain setting, 300 ms response time setting, measurement center distance, interference prevention function not used and white ceramic board object. 2) Including the sensor head. 3) The linearity of the sensor head and the controller has been adjusted at the time of factory shipment. Carry out the shift adjustment and the span adjustment to suit the operating conditions. High-functional Type NPN output PNP output Item Model No. LH-CS6 LH-CD6 LH-CS6P LH-CD6P Applicable sensor head LH-54, LH-58, LH-512 Connectable sensor heads (Max.) 1 No. 2 Nos. 1 No. 2 Nos. Supply voltage 24 V DC�10 % Ripple P-P 10 % or less Current consumption (Note 2) 300 mA or less 350 mA or less 300 mA or less 350 mA or less Analog voltage Analog current Analog output • Output voltage:�5 to�5 V/F.S. • Output current: 4 to 20 mA/F.S. • Output impedance: 100 Ω • Load resistance: 300 Ω or less Response time (10 to 90 %) 0.5 ms / 1 ms / 10 ms / 20 ms / 30 ms / 40 ms / 100 ms / 300 ms selectable by key (Automatic response time setting is possible.) Temperature characteristics Within �0.04 % F.S./°C Span adjustment / Shift adjustment Within �30 % F.S. (Note 3) Three outputs (HI, GO, LO) Three outputs (HI, GO, LO) NPN open-collector transistor PNP open-collector transistor • Maximum sink current: 30 mA • Maximum source current: 30 mA Comparative output • Applied voltage: 30 V DC or less • Applied voltage: 30 V DC or less (between comparative output and 0 V) (between comparative output and �V) • Residual voltage: 1.0 V or less (at 30 mA sink current) • Residual voltage: 1.0 V or less (at 30 mA source current) 0.4 V or less (at 16 mA sink current) 0.4 V or less (at 16 mA source current) Output operation ON when threshold level is reached Short-circuit protection Incorporated Alarm output Incorporated Strobe output Incorporated Ambient temperature 0 to�50 °C �32 to�122 °F (No dew condensation), Storage:�20 to�60 °C �4 to�140 °F Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH Weight 120 g approx. Accessory ATA4811 (Controller mounting frame): 1 set. Notes: 1) Conditions which have not been specified are to be taken as: 24 V DC supply voltage,�20 °C �68 °F ambient temperature, SELECT gain setting, 300 ms response time setting, measurement center distance, interference prevention function not used and white ceramic board object. 2) Including the sensor head. 3) The linearity of the sensor head and the controller has been adjusted at the time of factory shipment. Carry out the shift adjustment and the span adjustment to suit the operating conditions. 910 GP-A GP-X LD LA LA-300 HL-T1 LM10 LH-50 HL-C1 MEASUREMENT SENSORS Magnetic Displacement Light / Thru-beam Type Light / Reflective Type LH-50 I/O CIRCUIT DIAGRAMS (CONTROLLER) LH-CL6 NPN output type Color code Notes: 1) The device connected to the analog voltage output (black) should have an input impedance of 1 MΩ or more. D1 (Brown)�V Notes: 2) The device connected to the analog current output (white) should (Black / White) ZD1 have a load resistance of 300 Ω or less. Comparative Load output (OUT 1) Notes: 3) Do not connect an interference prevention I/O wire other than that Load of LH-CL6(P) to the interference prevention I/O (orange / violet). 100 mA max. Load ZD2 Tr1 � (Black / Gray) Comparative output (OUT 2) 24 V DC Further, do not connect together two controllers which have both �10 % been set as masters during interference prevention setting, as this � 100 mA max. ZD3 Tr2 (Gray) Alarm output will cause a fault. 100 mA max. Tr3 (Blue) 0 V Symbols … D1: Reverse supply polarity protection diode D2 to D5: Input protection diode 100 Ω � (Black) Analog voltage output �5 to�5 V (Note 1) � ZD1 to ZD5: Surge absorption zener diode ZD4 Tr1 to Tr3: NPN output transistor (Black shield) Analog voltage output GND �12 V m1 � � ZD5 (White) Analog current output 4 to 20 mA (Note 2) Non-voltage contact or NPN open-collector transistor (White shield) Analog current output GND D2 4.7 kΩ (Light blue) 0-ADJ input or D3 4.7 kΩ (Violet) External synchronization input • 0-ADJ input, External synchronization input • Remote interlock input D4 4.7 kΩ Low (0 to 1 V): Effective Low (0 to 1 V): Emission (Pink) Remote interlock input High (�V or open): Ineffective High (�V or open): Emission halt (Orange / Violet) D5 4.7 kΩ Interference prevention I/O (Note 3) 22 kΩ (Pink / Black) Input COM. m1 m1 m1 22 kΩ (Blue / White) Input COM. Internal circuit Users’ circuit LH-CL6P PNP output type Color code Notes: 1) The device connected to the analog voltage output (black) should have an input impedance of 1 MΩ or more. (Brown)�V Notes: 2) The device connected to the analog current output (white) should have a load resistance of 300 Ω or less. ZD1 100 mA max. Notes: 3) Do not connect an interference prevention I/O wire other than that Tr1 (Black / White) Comparative output (OUT 1) of LH-CL6(P) to the interference prevention I/O (orange / violet). ZD2 100 mA max. � 24 V DC Further, do not connect together two controllers which have both Tr2 �10 % (Black / Gray) Comparative output (OUT 2) been set as masters during interference prevention setting, as this � Load ZD3 100 mA max. will cause a fault. Tr3 Load (Gray) Load D1 Alarm output Symbols … D1: Reverse supply polarity protection diode (Blue) 0 V 100 Ω D2 to D5: Input protection diode � (Black) Analog voltage output �5 to�5 V (Note 1) � ZD1 to ZD5: Surge absorption zener diode ZD4 Tr1 to Tr3: PNP output transistor (Black shield) Analog voltage output GND �12 V � m1 � ZD5 (White) Analog current output 4 to 20 mA (Note 2) Non-voltage contact or PNP open-collector transistor (White shield) Analog current output GND D2 4.7 kΩ (Light blue) 0-ADJ input or D3 4.7 kΩ (Violet) External synchronization input • 0-ADJ input, External synchronization input • Remote interlock input D4 4.7 kΩ Low (0 to 1 V, or open): Ineffective (Pink) Remote interlock input Low (0 to 1 V, or open): Emission halt High (�V): Effective High (�V): Emission (Orange / Violet) D5 4.7 kΩ Interference prevention I/O (Note 3) 22 kΩ (Pink / Black) Input COM. m1 m1 m1 22 kΩ (Blue / White) Input COM. Internal circuit Users’ circuit 911 Main circuit Main circuit Magnetic Displacement Light / Thru-beam Type Light / Reflective Type MEASUREMENT SENSORS GP-A GP-X LD LA LA-300 HL-T1 LM10 LH-50 HL-C1 LH-50 I/O CIRCUIT DIAGRAMS (CONTROLLER) LH-CS6 NPN output type LH-CD6 Notes: 1) The device connected to ‘1 Analog voltage output’ should have an Terminal No. input impedance of 1 MΩ or more. Notes: 2) The device connected to ‘3 Analog current output’ should have a D1 �V 11 load resistance of 300 Ω or less. Comparative Load ZD1 output HI Notes: 3) In case of LH-CS6, terminal No. 6 is not used. 13 Tr1 Load Notes: 4) Do not wire an interference prevention I/O other than that of ZD2 30 mA max. Comparative output GO 14 LH-CS6(P) or LH-CD6(P) to the interference prevention I/O. Load Tr2 � Further, do not connect together two controllers which have both ZD3 30 mA max. Comparative output LO Load 24 V DC 15 Tr3 �10 % been set as masters during interference prevention setting, as this � Load 30 mA max. ZD4 Strobe output will cause a fault. 16 Tr4 30 mA max. ZD5 Alarm output 17 Tr5 Symbols … D1: Reverse supply polarity protection diode 30 mA max. 0 V D2 to D7: Input protection diode 12 100 Ω ZD1 to ZD7: Surge absorption zener diode � 1 Analog voltage output �5 to�5 V (Note 1) � Tr1 to Tr5: NPN output transistor ZD6 2 GND for analog output �12 V m1 � ZD7 � 3 Analog current output 4 to 20 mA (Note 2) Non-voltage contact or NPN open-collector transistor D2 4.7 kΩ BUSY input HEAD 1 5 D3 4.7 kΩ BUSY input HEAD 2 (Note 3) 6 or D4 4.7 kΩ Calculation hold reset input 7 D5 4.7 kΩ • Remote interlock input 0-ADJ input • 0-ADJ input, BUSY input 19 Low (0 to 1 V): Emission Calculation hold reset input D6 4.7 kΩ Remote interlock input High (�V or open): Emission halt 9 Low (0 to 1 V): Effective Interference D7 4.7 kΩ High (�V or open): Ineffective prevention I/O 4 (Note 4) Input COM. Upper terminal block Lower terminal block 10 m1 m1 m1 m1 m1 Input COM. Terminal Terminal Description Description 18 No. No. Input COM. 8 1 Analog voltage output A �V 2 GND for analog output B 0 V 1234567890 Internal circuit Users’ circuit 3 Analog current output C Comparative output HI Terminal 4 Interference prevention I/O D Comparative output GO No. Upper terminal Terminal arrangement diagram 5 BUSY input HEAD 1 E Comparative output LO block 6 BUSY input HEAD 2 (Note) F Strobe output Lower terminal 7 Calculation hold reset input G Alarm output block 8 Input COM. H Input COM. 9 Remote Interlock input I 0-ADJ input 0 Input COM. ABCDEFGHI Note: Not for the LH-CS6 LH-CS6P PNP output type LH-CD6P Notes: 1) The device connected to ‘1 Analog voltage output’ should have an Terminal No. input impedance of 1 MΩ or more. Notes: 2) The device connected to ‘3 Analog current output’ should have a ZD1 �V 11 load resistance of 300 Ω or less. 30 mA max. Comparative output HI Notes: 3) In case of LH-CS6P, terminal No. 6 is not used. 13 Tr1 Notes: 4) Do not wire an interference prevention I/O other than that of 30 mA max. ZD2 Comparative output GO Tr2 LH-CS6(P) or LH-CD6(P) to the interference prevention I/O. 14 Comparative output LO 30 mA max. Load ZD3 � Further, do not connect together two controllers which have both 24 V DC Tr3 15 Load �10 % been set as masters during interference prevention setting, as this 30 mA max. � ZD4 Strobe output will cause a fault. Tr4 16 Load 30 mA max. Alarm output Load Tr5 17 Symbols … D1: Reverse supply polarity protection diode ZD5 Load D1 0 V D2 to D7: Input protection diode 12 100 Ω ZD1 to ZD7: Surge absorption zener diode � 1 Analog voltage output �5 to�5 V (Note 1) � Tr1 to Tr5: PNP output transistor ZD6 2 GND for analog output �12 V m1 � ZD7 � 3 Analog current output 4 to 20 mA (Note 2) Non-voltage contact or PNP open-collector transistor D2 4.7 kΩ BUSY input HEAD 1 5 D3 4.7 kΩ BUSY input HEAD 2 (Note 3) 6 or D4 4.7 kΩ Calculation hold reset input 7 D5 4.7 kΩ • 0-ADJ input, BUSY input • Remote interlock input 0-ADJ input 19 Calculation hold reset input Low (0 to 1 V, or open): Emission halt D6 4.7 kΩ Remote interlock input Low (0 to 1 V, or open): Ineffective High (�V): Emission 9 Interference D7 4.7 kΩ High (�V): Effective prevention I/O 4 (Note 4) Input COM. Upper terminal block Lower terminal block 10 m1 m1 m1 m1 m1 Input COM. Terminal Terminal 18 Description Description No. No. Input COM. 8 1 Analog voltage output A V � 2 GND for analog output B 0 V 1234567890 Internal circuit Users’ circuit 3 Analog current output C Comparative output HI Terminal 4 Interference prevention I/O D Comparative output GO No. Upper terminal Terminal arrangement diagram 5 BUSY input HEAD 1 E Comparative output LO block 6 BUSY input HEAD 2 (Note) F Strobe output 7 Calculation hold reset input G Alarm output Lower terminal block 8 Input COM. H Input COM. 9 Remote Interlock input I 0-ADJ input 0 Input COM. ABCDEFGHI Note: Not for the LH-CS6P 912 GP-A GP-X LD LA LA-300 HL-T1 LM10 LH-50 HL-C1 MEASUREMENT SENSORS Magnetic Displacement Light / Thru-beam Type Light / Reflective Type Main circuit Main circuit LH-50 LIST OF MAIN CONTROLLER FUNCTIONS Please refer to the separate ‘User’s Manual’ for more details pertaining to specifications. (Refer to p.916) Common functions (common to general purpose controller and high-functional controller) Item Function Outline Automatically sets the gain to the optimum level to match changes in the reflection AUTO gain setting function ratio for the measured objects. Lets the user select the gain to match changes in the reflection ratio for the Measuring condition SELECT gain setting function measured objects. Lets the user select the response time to match the line speed for the measured Response time setting function objects. Analog output Adjusts the analog output and the Shift adjustment function shift value for display values. Analog output Adjusts the analog output and the Span adjustment function span value for display values. Adjustment Measurement value Forcibly resets the currently Display value measured value to ‘0’ and then 0-ADJ function caries out measurement with this ‘0’ value as a reference 0-ADJ input 0-ADJ function clear function Returns the value which was forcibly set to ‘0’ using the 0-ADJ function back to its original value. 0-ADJ value memory function Enables the 0-ADJ value to be stored in memory. Analog output off-set function Applies a user-defined offset to the analog output. Teaching function Allow the measured value for the measured object to be used to set the threshold value. Time chart Sensing Sensing condition Non-sensing ON-delay: ON Disables short-term detection. Comparative output Normal operation OFF Timer function OFF-delay: ON T Extends the output signal for a constant ON-delay OFF ON length of time. T TT OFF-delay OFF Timer period: T�0 to 1,000 ms Distance display / Displacement value display select function Toggles the display between distance and displacement value display. Display Sleep function Turns off value display. If measurement is not possible, this function maintains analog output at the level Analog output hold function output immediately before this occurs. Others Prevents mutual interference when using two sensors in close proximity. Interference prevention function [If using the LH-CD6(P) high-functional controller, interference can be prevented for up to four sensors.] Additional functions (high-functional controller) Item Function Outline Automatically sets the response time to match the line speed of the measured Measuring condition Automatic response time setting function objects in order to provide optimum resolution. Carries out arithmetical processing on the channel A input value and the channel B input value. A�B: Calculates the sum of the measured values for channel A and channel B. A�B: Calculates the difference between the measured values for channel A and channel B. Calculation function L�(A�B): Subtracts the sum of the measured values for channel A and channel B from a constant value L. [LH-CD6(P) only] L�(A�B): Subtracts the measured value for channel B from the measured value for channel A, and subtracts the result from a constant value L. Calculation and measurement (A�B) / 2 : Obtains the simple average of the measured values for channel A and channel B. Peak-to-peak hold: Holds and displays the difference between the maximum and minimum values obtained during the measuring period. Measurement function Peak hold: Holds and displays the maximum value obtained during the measuring period. Bottom hold: Holds and displays the minimum value obtained during the measuring period. Set value memory Set value memory function Allows setting details to be stored in up to 16 different memory locations. Allows measured values and setting values to be transmitted via an RS-232C interface. Communication RS-232C communication function 913 Magnetic Displacement Light / Thru-beam Type Light / Reflective Type MEASUREMENT SENSORS GP-A GP-X LD LA LA-300 HL-T1 LM10 LH-50 HL-C1 LH-50 DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ LH-54 LH-58 Sensor head LH-512 30 4.5 1.181 0.177 Operation indicator (Green / Orange) Emission indicator (Yellow) 17 1.3 46 2-"3.4 "0.134 mounting holes 0.669 0.051 1.811 h $ 39 Beam axis 1.535 34 46 1.339 1.811 Measurement Emission / Model No. 3.5 39 center distance h Reception angle $ 3.5 0.138 0.138 1.535 40 mm 1.575 in 20.5 � LH-54 "6 "0.236 cable, 0.2 m 0.656 ft long 80 mm 3.150 in 11.5 � LH-58 43 1.693 LH-512 120 mm 4.724 in 8.3 � 14.7 0.579 LH-CL6 Controller LH-CL6P Emitting indicator (Yellow) 0-ADJ indicator (Green) 54.9 2.161 5.5 5.5 5.5 Analog output hold indicator (Orange) 0.217 0.217 0.217 10 6 8.5 Comparative output indicator External syncronization indicator (Green) 0.394 0.236 0.335 (OUT1, OUT2)(Orange) 3.45 0.136 6 0.236 3 4 0.118 0.157 5 digit LED display (Red) Jog switch Mode selection switch 26 1.024 24 (4.7) 67 (4.5) 0.945 (0.185) 2.638 (0.177) "6 "0.236 cable, 2 m 6.562 ft long 40 1.575 18 18 0.709 0.709 19.1 36.5 0.752 1.437 Connector for head connection Suitable for 35 mm 1.378 in width DIN rail 914 GP-A GP-X LD LA LA-300 HL-T1 LM10 LH-50 HL-C1 MEASUREMENT SENSORS Magnetic Displacement Light / Thru-beam Type Light / Reflective Type LH-50 DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ LH-CS6 Controller LH-CS6P RS-232C modular 77.5 connector �48 �1.890 3.051 7.15 (4.5) 5.5 10.35 73 23.5 Terminal block 0.281 (0.177) 0.217 0.407 2.874 0.925 9.8 0.386 26.5 8.7 1.043 0.343 40.55 6.4 0.252 1.596 �44.5 10 4.2 0.165 �1.752 3.5 0.138 4.2 0.165 0.394 4.5 0.177 10.5 16.5 8.5 8.5 0.413 0.650 0.335 0.335 Connector for sensor head connection 9.75 9.5 9.5 9.5 0.384 0.374 0.374 0.374 Panel cut-out dimensions Display scale indicator (Orange) 5 digit LED display (Red) A Display hold Selected channel indicator (Orange) In case of adjacent mounting �0.6 indicator (Orange) A�(48� n�2.5) 0 Emission indicator (Yelllow) �0.024 A�(1.890� n�0.098) �0.6 0 45 0 Comparative output �0.024 BUSY indicator (Green) 1.772 indicators 0 (HI, GO, LO) Panel lock indicator (Orange) (Orange, Green, Orange) Analog output hold mode indicator (Orange) �0.6 0-ADJ indicator 45 0 Min. 90 SET key (Green) �0.024 1.772 Min. 3.543 0 DOWN key MODE key UP key Note: The panel thickness should be 1 to 5 mm 0.039 to 0.197 in. LH-CD6 Controller LH-CD6P RS-232C modular 77.5 connector �48 �1.890 3.051 7.15 5.5 10.35 5.5 5.5 (4.5) Terminal block 73 23.5 0.281 0.217 0.407 0.217 0.217 (0.177) 2.874 0.925 9.8 0.386 8.7 26.5 0.343 1.043 40.55 6.4 0.252 1.596 �44.5 10 4.2 0.165 3.5 0.138 �1.752 4.2 0.165 0.394 4.5 0.177 10.5 10.5 11.5 0.413 0.413 0.453 16.5 8.5 8.5 Connector for sensor 0.650 0.335 0.335 head connection (head1) 9.75 9.5 9.5 9.5 0.384 0.374 0.374 0.374 Connector for sensor head connection (head2) Panel cut-out dimensions Display scale indicator (Orange) 5 digit LED display (Red) A Display hold Selected channel indicators (Orange) In case of adjacent mounting indicator (Orange) �0.6 A�(48� n�2.5) 0 Emission indicators (Yelllow) �0.024 A�(1.890� n�0.098) �0.6 0 45 Comparative output 0 BUSY indicators (Green) �0.024 indicators 1.772 0 (HI, GO, LO) Panel lock indicator (Orange) (Orange, Green, Orange) Analog output hold mode indicator (Orange) 0-ADJ indicator �0.6 45 0 (Green) SET key Min. 90 �0.024 1.772 Min. 3.543 0 DOWN key MODE key UP key Note: The panel thickness should be 1 to 5 mm 0.039 to 0.197 in. 915 Magnetic Displacement Light / Thru-beam Type Light / Reflective Type MEASUREMENT SENSORS GP-A GP-X LD LA LA-300 HL-T1 LM10 LH-50 HL-C1 LH-50 PRECAUTIONS FOR PROPER USE This product is not a safety sensor. Its use is not intended or designed to protect life and prevent body injury or property damage from dangerous parts of machinery. It is a normal object detection sensor. Conditions in use for CE conformity • The LH-50 series is a CE conformity product complying with EMC Directive. The harmonized standard with regard to immunity that applies to this product is EN 61000-6-2 and the following conditions must be met to conform to that standard. Conditions • This controller should be connected less than 10 m 32.808 ft from the power supply. • The signal line to connect with this controller should be less than 30 m 98.425 ft. Note: The EN 50082-2 that previously applied to the products for conforming to EMC Directive was replaced by EN 61000-6-2 starting April 1st, 2002. Guide to Users Manual and Technical Reference Manual The separate ‘Users Manual’ contains details on the functions, applications, operating procedures and notes on use for the various controllers. In addition, a ‘Technical Data’ which contains technical data which can be used as reference for actual use is also available. The applications described in this catalog as well as in the user’s manuals are reference examples. Make sure to familiarize yourself will with the functions of these devices prior to use. 916 GP-A GP-X LD LA LA-300 HL-T1 LM10 LH-50 HL-C1 MEASUREMENT SENSORS Magnetic Displacement Light / Thru-beam Type Light / Reflective Type

Frequently asked questions

What makes Elite.Parts unique?

At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the LH-CS6P have?

Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

Quality

We are industry veterans who take pride in our work

Protection

Avoid the dangers of risky trading in the gray market

Access

Our network of suppliers is ready and at your disposal

Savings

Maintain legacy systems to prevent costly downtime

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

LA-305

PANASONIC

Panasonic LA-305 Sensor - RED LED THRU 5X300MM,0.05MM DIA.

LA-305D

PANASONIC

Panasonic LA-305D Sensor - RED LED THRU 5X300MM,0.05MM DIA. RECEIVER

LA-310

PANASONIC

Panasonic LA-310 Sensor - RED LED THRU 10X500MM,0.1MM DIA.

LA-510

PANASONIC

Panasonic LA-510 Sensor - LASER SENSOR THRU 15X500MM 0.1MM 1-5V 0.5MS CLASS-1(JIS/IEC)

LA-511

PANASONIC

Panasonic LA-511 Sensor - LASER BEAM SENSOR,THRU 15X500MM 0.1MM 1-5V 0.5MS CLASS-1(FDA) RoHS Complia...

LA-511D

PANASONIC

Panasonic LA-511D Sensor - LASER SENSOR THRU 15X500MM 0.1MM 1-5V 0.5MS CLASS-1(FDA),RECEIVER

Request a Quote

Part information

Part Number*

Error Message