ON SEMICONDUCTOR NCP582DSQ18T1G
Description
IC REG LDO 1.8V 150MA LN SC82AB
Part Number
NCP582DSQ18T1G
Price
Request Quote
Manufacturer
ON SEMICONDUCTOR
Lead Time
Request Quote
Category
PRODUCTS - N
Datasheet
Extracted Text
NCP582 Low Noise 150 mA CMOS LDO Regulator with Enable The NCP582 series of low dropout regulators are designed for portable battery powered applications which require precise output voltage accuracy, low supply current, and high ripple rejection. These devices feature an enable function and are offered in active http://onsemi.com low and active high with auto discharge. MARKING The following ceramic capacitors are the recommended values to DIAGRAMS be used with these devices; for V < 2.5 V, C = C = 1.0 �F, out in out V � 2.5 V, C = C = 0.47 �F. out in out SC−82AB Features xx M SQ SUFFIX 4 • Ultra−Low Dropout Voltage of 220 mV at 150 mA CASE 419C • Low Output Noise of 30 �Vrms 1 1 • Excellent Line and Load Regulation • High Output Voltage Accuracy of �2% SOT−563 • Low Supply Current of 75 �A yyyy M XV SUFFIX 6 • Excellent Power Supply Rejection Ratio CASE 463A 1 • Wide Operating Voltage of 1.5 V to 3.3 V 1 • Low Quiescent Current of 0.1 �A xx, yyyy = Specific Device Code • Fast Dynamic Performance M = Date Code • Fold Back Protection Circuit • Low Temperature Drift Coefficient on the Output Voltage ORDERING INFORMATION • These are Pb−Free Devices See detailed ordering and shipping information in the package Typical Applications dimensions section on page 12 of this data sheet. • Portable Equipment • Hand−Held Instrumentation • Camcorders and Cameras V V V V in in out out - - + + V V ref ref Current Limit Current Limit CE GND CE GND Figure 1. Simplified Block Diagram Figure 2. Simplified Block Diagram for Active Low for Active High with Auto Discharge Semiconductor Components Industries, LLC, 2004 1 Publication Order Number: September, 2004 − Rev. 2 NCP582/D NCP582 PIN FUNCTION DESCRIPTION SOT−563 SC−82AB Pin Pin Symbol Description 1 4 Power supply input voltage. V in 2 2 GND Power supply ground. 3 3 Regulated output voltage. V out 4 − NC No connect. 5 − GND Power supply ground. 6 1 CE or CE Chip enable pin. MAXIMUM RATINGS Rating Symbol Value Unit Input Voltage V 6.5 V in Input Voltage (CE or CE Pin) V −0.3 to V +0.3 V CE in Output Voltage V −0.3 to V +0.3 V out in Output Current I 200 mA out Power Dissipation P mW D SC−82AB 150 SOT−563 500 Operating Junction Temperature Range T −40 to +85 °C J Storage Temperature Range T +150 °C stg Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. http://onsemi.com 2 NCP582 ELECTRICAL CHARACTERISTICS (V = V + 1.0 V, T = 25°C, unless otherwise noted.) in out A Characteristic Symbol Min Typ Max Unit Input Voltage V 2.0 − 6.0 V in Output Voltage (I = 1.0 mA to 30 mA) V V X 0.980 − V X 1.020 V out out out out Line Regulation (I = 30 mA) Reg − 0.02 0.10 %/V out line (V > 1.7 V; V + 0.5 V � V � 6.0 V) out out in (V � 1.7 V; 2.2 V � V � 6.0 V) out in Load Regulation (I = 1.0 mA to 150 mA) Reg − 22 40 mV out load Dropout Voltage (I = 150 mA) V V out DO V = 1.5 V − 0.38 0.70 out V = 1.8 V − 0.32 0.55 out V = 2.5 V − 0.28 0.50 out 2.8 V � V � 3.3 V − 0.22 0.35 out Power Supply Current (I = 0 mA) Isupply − 75 95 �A out Output Current I 150 − − mA out Quiescent Current (V = Gnd for Active High with Auto Discharge) I − 0.1 1.0 �A CE Q (V = V for Active Low) CE in Output Short Circuit Current (V = 0) I − 40 − mA out lim Ripple Rejection (I = 30 mA) RR dB out (V > 1.7 V; V – V = 1.0 V) out in out (V � 1.7 V; V – V = 1.2 V) out in out f = 1.0 kHz − 70 − f = 10 kHz − 60 − Enable Input Threshold Voltage V High 1.5 − V Vth in enh Low 0 − 0.3 Vth enl Output Noise Voltage (Bandwidth = 10 Hz to 100 kHz) V − 30 − �Vrms n Output Voltage Temperature Coefficient �V /�T − �100 − ppm/°C out (I = 30 mA, −40°C � T � 85°C) out A http://onsemi.com 3 NCP582 TYPICAL CHARACTERISTICS 1.6 3.0 1.4 2.5 V = 4.8 V in 1.2 1.8 V 2.0 1.0 0.8 1.5 3.1 V V = 3.5 V in 0.6 2.5 V 3.5 V 1.0 3.8 V 0.4 2.0 V 0.5 0.2 V = 1.5 V out V = 2.8 V out 0 0 300 300 0 100 200 400 0 100 200 400 OUTPUT CURRENT I (mA) OUTPUT CURRENT I (mA) out out Figure 3. Output Voltage vs. Output Current Figure 4. Output Voltage vs. Output Current 4.5 1.7 4.0 1.6 3.5 V = 6.0 V in 1.5 3.0 I = 1.0 mA out 1.4 2.5 5.0 V I = 30 mA 2.0 out 4.5 V 1.3 4.3 V 1.5 I = 50 mA out 1.2 1.0 1.1 V = 1.5 V out V = 4.0 V 0.5 out 1.0 0 300 4.0 0 100 200 400 1.0 2.0 3.0 5.0 6.0 OUTPUT CURRENT I (mA) INPUT VOLTAGE V (V) out in Figure 5. Output Voltage vs. Output Current Figure 6. Output Voltage vs. Input Voltage 2.9 4.2 2.8 4.0 2.7 3.8 2.6 I = 1.0 mA out I = 1.0 mA out 2.5 I = 30 mA out 3.6 I = 30 mA 2.4 out I = 50 mA out 2.3 3.4 I = 50 mA out 2.2 3.2 V = 2.8 V 2.1 out V = 4.0 V out 2.0 3.0 2.0 3.0 4.0 5.0 6.0 1.0 2.0 3.0 4.0 5.0 6.0 INPUT VOLTAGE V (V) INPUT VOLTAGE V (V) in in Figure 7. Output Voltage vs. Input Voltage Figure 8. Output Voltage vs. Input Voltage http://onsemi.com 4 OUTPUT VOLTAGE V (V) OUTPUT VOLTAGE V (V) OUTPUT VOLTAGE V (V) out out out OUTPUT VOLTAGE V (V) OUTPUT VOLTAGE V (V) OUTPUT VOLTAGE V (V) out out out NCP582 TYPICAL CHARACTERISTICS 90 90 80 80 70 70 60 60 50 50 40 40 30 30 20 20 V = 1.5 V V = 2.8 V 10 out 10 out 0 0 0 1.0 2.0 3.0 4.0 5.0 6.0 0 1.0 2.0 3.0 4.0 5.0 6.0 INPUT VOLTAGE V (V) INPUT VOLTAGE V (V) in in Figure 9. Power Supply Current vs. Input Voltage Figure 10. Power Supply Current vs. Input Voltage 90 1.53 80 1.52 70 1.51 60 1.50 50 40 1.49 30 1.48 20 V = 1.5 V 1.47 out V = 4.0 V 10 out 0 1.46 4.0 60 0 1.0 2.0 3.0 5.0 6.0 −40 −15 10 35 85 INPUT VOLTAGE V (V) TEMPERATURE (°C) in Figure 11. Power Supply Current vs. Input Voltage Figure 12. Output Voltage vs. Temperature 2.86 4.08 4.06 2.84 4.04 2.82 4.02 2.80 4.00 3.98 2.78 3.96 2.76 3.94 V = 4.0 V V = 2.8 V out out 3.92 2.74 −40 −15 10 35 60 85 −40 −15 10 35 60 85 TEMPERATURE (°C) TEMPERATURE (°C) Figure 14. Output Voltage vs. Temperature Figure 13. Output Voltage vs. Temperature http://onsemi.com 5 SUPPLY CURRENT, I (�A) SUPPLY CURRENT, I (�A) supply OUTPUT VOLTAGE, V (V) supply out OUTPUT VOLTAGE, V (V) out OUTPUT VOLTAGE, V (V) SUPPLY CURRENT, I (�A) out supply NCP582 TYPICAL CHARACTERISTICS 90 90 80 80 70 70 60 60 50 50 40 40 30 30 20 20 V = 1.5 V V = 2.8 V 10 out 10 out 0 0 −40 −15 10 35 60 85 −40 −15 10 35 60 85 TEMPERATURE (°C) TEMPERATURE (°C) Figure 15. Power Supply Current vs. Temperature Figure 16. Power Supply Current vs. Temperature 90 0.6 80 0.5 70 60 0.4 85°C 50 25°C 0.3 40 0.2 30 −40°C 20 0.1 V = 4.0 V out 10 V = 1.5 V out 0.0 0 −40 −15 10 35 60 85 0 25 50 75 100 125 150 TEMPERATURE (°C) OUTPUT CURRENT I (mA) out Figure 17. Power Supply Current vs. Temperature Figure 18. Dropout Voltage vs. Output Current 0.6 0.40 0.35 0.5 0.30 0.4 85°C 0.25 85°C 25°C 0.3 0.20 25°C 0.15 0.2 −40°C −40°C 0.10 0.1 0.05 V = 2.8 V V = 1.8 V out out 0.0 0.00 0 25 50 75 100 125 150 0 25 50 75 100 125 150 OUTPUT CURRENT I (mA) OUTPUT CURRENT I (mA) out out Figure 19. Dropout Voltage vs. Output Current Figure 20. Dropout Voltage vs. Output Current http://onsemi.com 6 SUPPLY CURRENT, I (�A) SUPPLY CURRENT, I (�A) DROPOUT VOLTAGE, V (V) DO supply supply DROPOUT VOLTAGE, V (V) SUPPLY CURRENT, I (�A) DO DROPOUT VOLTAGE, V (V) supply DO NCP582 TYPICAL CHARACTERISTICS 0.40 90 80 0.35 70 0.30 60 0.25 50 85°C 0.20 40 25°C 0.15 30 0.10 −40°C 20 V = 2.5 Vdc + 0.5 Vp−p in 0.05 10 V = 1.5 V out C = Ceramic 1.0 �F V = 4.0 V out out 0.00 0 0 25 50 75 100 125 150 10 0.1 1 100 OUTPUT CURRENT I (mA) FREQUENCY, f (kHz) out Figure 21. Dropout Voltage vs. Output Current Figure 22. Ripple Rejection vs. Frequency 90 90 80 80 70 70 60 60 50 50 40 40 30 30 20 20 V = 2.5 Vdc + 0.5 Vp−p V = 3.8 Vdc + 0.5 Vp−p in in 10 V = 1.5 V 10 out V = 2.8 V C = Ceramic 2.2 �F C = Ceramic 0.47 �F out out out 0 0 0.1 1 10 100 0.1 1 10 100 FREQUENCY, f (kHz) FREQUENCY, f (kHz) Figure 23. Ripple Rejection vs. Frequency Figure 24. Ripple Rejection vs. Frequency 90 90 80 80 70 70 60 60 50 50 40 40 30 30 20 20 V = 3.8 Vdc + 0.5 Vp−p V = 5.0 Vdc + 0.5 Vp−p in in 10 V = 2.8 V 10 V = 4.0 V out out C = Ceramic 1.0 �F C = Ceramic 0.47 �F out out 0 0 10 10 0.1 1 100 0.1 1 100 FREQUENCY, f (kHz) FREQUENCY, f (kHz) Figure 26. Ripple Rejection vs. Frequency Figure 25. Ripple Rejection vs. Frequency http://onsemi.com 7 RIPPLE REJECTION, RR (dB) RIPPLE REJECTION, RR (dB) DROPOUT VOLTAGE, V (V) DO RIPPLE REJECTION, RR (dB) RIPPLE REJECTION, RR (dB) RIPPLE REJECTION, RR (dB) NCP582 TYPICAL CHARACTERISTICS 90 80 70 60 50 40 30 20 V = 5.0 Vdc + 0.5 Vp−p in 10 V = 4.0 V out C = Ceramic 1.0 �F out 0 10 0.1 1 100 FREQUENCY, f (kHz) Figure 27. Ripple Rejection vs. Frequency V = 1.5 V out 1.55 4 1.54 3 Input Voltage 1.53 2 1.52 1 1.51 0 Output Voltage 1.50 1.49 0 10 20 30 40 50 60 70 80 90 100 TIME, t (�s) = 2.8 V V out 2.85 6 2.84 5 Input Voltage 4 2.83 3 2.82 2 2.81 Output Voltage 1 2.80 0 2.79 0 10 20 30 40 50 60 70 80 90 100 TIME, t (�s) Figure 28. Input Transient Response (I = 30 mA, C = 0, tr = tf = 5.0 �s, C = 0.47 �F) out in out http://onsemi.com 8 OUTPUT VOLTAGE, V (V) OUTPUT VOLTAGE, V (V) out out RIPPLE REJECTION, RR (dB) INPUT VOLTAGE, V (V) INPUT VOLTAGE, V (V) in in NCP582 TYPICAL CHARACTERISTICS (V = 2.5 V, C = 1.0 �F, V = 1.5 V) in out out 1.75 150 1.70 100 Output Current 1.65 50 1.60 0 1.55 Output Voltage 1.50 1.45 021416181024618 20 TIME, t (�s) (V = 2.5 V, C = 2.2 �F, V = 1.5 V) in out out 1.75 150 1.70 100 Output Current 1.65 50 1.60 0 1.55 Output Voltage 1.50 1.45 021416181024618 20 TIME, t (�s) Figure 29. Load Transient Response (tr = tf = 0.5 �s, C = 1.0 �F) in http://onsemi.com 9 OUTPUT VOLTAGE, V (V) OUTPUT VOLTAGE, V (V) out out OUTPUT CURRENT, I (mA) OUTPUT CURRENT, I (mA) out out NCP582 TYPICAL CHARACTERISTICS (V = 3.8 V, C = 0.47 �F, V = 2.8 V) in out out 3.05 150 3.00 100 Output Current 2.95 50 2.90 0 2.85 Output Voltage 2.80 2.75 021416181024618 20 TIME, t (�s) (V = 3.8 V, C = 1.0 �F, V = 2.8 V) in out out 3.05 150 3.00 100 Output Current 2.95 50 2.90 0 2.85 Output Voltage 2.80 2.75 021416181024618 20 TIME, t (�s) (V = 3.8 V, C = 2.2 �F, V = 2.8 V) in out out 3.05 150 3.00 100 Output Current 2.95 50 2.90 0 2.85 Output Voltage 2.80 2.75 021416181024618 20 TIME, t (�s) Figure 29. (continued) Load Transient Response (tr = tf = 0.5 �s, C = 1.0 �F) in http://onsemi.com 10 OUTPUT VOLTAGE, V (V) OUTPUT VOLTAGE, V (V) OUTPUT VOLTAGE, V (V) out out out OUTPUT CURRENT, I (mA) OUTPUT CURRENT, I (mA) OUTPUT CURRENT, I (mA) out out out NCP582 4 6 4 6 3 5 3 5 2 4 2 4 V in V in 3 1 1 3 I = 0 mA out I = 0 mA out 0 0 2 2 I = 30 mA out I = 30 mA out 1 1 0 I = 150 mA 0 out I = 150 mA out −2 −50252 10 1505 −50 0 50 100 150 200 250 300 350 400 450 TIME, t (�s) TIME, t (�s) Figure 30. Turn−On/Off Speed with CE Pin (D Version) (V = 1.5 V, V = 2.5 V, C = 1.0 �F, C = 1.0 �F) out in in out 4 8 4 8 3 7 3 7 V in 2 V 6 2 6 in 1 5 1 5 I = 0 mA 4 4 0 0 out 3 3 −1 −1 I = 30 mA out I = 0 mA out 2 2 I = 30 mA out 1 1 I = 150 mA out 0 0 I = 150 mA out −50252 10 1505 −2008 20 40 600 100 120 140 160 180 TIME, t (�s) TIME, t (�s) Figure 31. Turn−On/Off Speed with CE Pin (D Version) (V = 2.8 V, V = 3.8 V, C = 0.47 �F, C = 0.47 �F) out in in out 8 14 8 14 6 12 6 12 4 10 10 4 V in V in 2 8 8 2 I = 0 mA out 0 6 0 6 I = 0 mA I = 30 mA out out 4 −2 4 −2 I = 30 mA out 2 2 I = 150 mA 0 0 out I = 150 mA out −2 −2 −50252 10 1505 −2008 20 40 600 100 120 140 160 180 TIME, t (�s) TIME, t (�s) Figure 32. Turn−On/Off Speed with CE Pin (D Version) (V = 4.0 V, V = 5.0 V, C = 0.47 �F, C = 0.47 �F) out in in out http://onsemi.com 11 CE INPUT VOLTAGE, V (V) CE INPUT VOLTAGE, V (V) CE INPUT VOLTAGE, V (V) CE CE CE OUTPUT VOLTAGE, V (V) OUTPUT VOLTAGE, V (V) out OUTPUT VOLTAGE, V (V) out out CE INPUT VOLTAGE, V (V) CE INPUT VOLTAGE, V (V) CE CE CE INPUT VOLTAGE, V (V) CE OUTPUT VOLTAGE, V (V) OUTPUT VOLTAGE, V (V) OUTPUT VOLTAGE, V (V) out out out NCP582 APPLICATION INFORMATION Input Decoupling performance, select a capacitor with low Equivalent Series A 1.0 �F ceramic capacitor is the recommended value to Resistance (ESR). For PCB layout considerations, place be connected between V and GND. For PCB layout in the output capacitor close to the output pin and keep the considerations, the traces of V and GND should be in leads short as possible. sufficiently wide in order to minimize noise and prevent Noise Decoupling unstable operation. The NCP582 series are low noise regulators and reach a Output Decoupling noise level of only 30 �Vrms between 10 Hz and 100 kHz. It is best to use a 1.0 �F capacitor value when V out �2.5 V and a 0.47 �F when V � 2.5 V. For better out ORDERING INFORMATION Nominal Output Device Output Type / Features Voltage Marking Package Shipping† NCP582DSQ15T1G Active High w/Auto Discharge 1.5 SF SC−82AB (Pb−Free) 3000 Tape & Reel NCP582DSQ18T1G Active High w/Auto Discharge 1.8 SJ SC−82AB (Pb−Free) 3000 Tape & Reel NCP582DSQ25T1G Active High w/Auto Discharge 2.5 TF SC−82AB (Pb−Free) 3000 Tape & Reel NCP582DSQ28T1G Active High w/Auto Discharge 2.8 TJ SC−82AB (Pb−Free) 3000 Tape & Reel NCP582DSQ30T1G Active High w/Auto Discharge 3.0 UA SC−82AB (Pb−Free) 3000 Tape & Reel NCP582DSQ33T1G Active High w/Auto Discharge 3.3 UD SC−82AB (Pb−Free) 3000 Tape & Reel NCP582DXV15T1G* Active High w/Auto Discharge 1.5 F15D SOT−563 (Pb−Free) 4000 Tape & Reel NCP582DXV18T1G* Active High w/Auto Discharge 1.8 F18D SOT−563 (Pb−Free) 4000 Tape & Reel NCP582DXV25T1G* Active High w/Auto Discharge 2.5 F25D SOT−563 (Pb−Free) 4000 Tape & Reel NCP582DXV28T1G* Active High w/Auto Discharge 2.8 F28D SOT−563 (Pb−Free) 4000 Tape & Reel NCP582DXV29T1G* Active High w/Auto Discharge 2.9 F29D SOT−563 (Pb−Free) 4000 Tape & Reel NCP582DXV30T1G* Active High w/Auto Discharge 3.0 F30D SOT−563 (Pb−Free) 4000 Tape & Reel NCP582DXV33T1G* Active High w/Auto Discharge 3.3 F33D SOT−563 (Pb−Free) 4000 Tape & Reel NCP582LSQ15T1G Active Low 1.5 JF SC−82AB (Pb−Free) 3000 Tape & Reel NCP582LSQ18T1G Active Low 1.8 JJ SC−82AB (Pb−Free) 3000 Tape & Reel NCP582LSQ25T1G Active Low 2.5 KF SC−82AB (Pb−Free) 3000 Tape & Reel NCP582LSQ28T1G Active Low 2.8 KJ SC−82AB (Pb−Free) 3000 Tape & Reel NCP582LSQ30T1G Active Low 3.0 LA SC−82AB (Pb−Free) 3000 Tape & Reel NCP582LSQ33T1G Active Low 3.3 LD SC−82AB (Pb−Free) 3000 Tape & Reel NCP582LXV15T1G* Active Low 1.5 F15A SOT−563 (Pb−Free) 4000 Tape & Reel NCP582LXV18T1G* Active Low 1.8 F18A SOT−563 (Pb−Free) 4000 Tape & Reel NCP582LXV25T1G* Active Low 2.5 F25A SOT−563 (Pb−Free) 4000 Tape & Reel NCP582LXV28T1G* Active Low 2.8 F28A SOT−563 (Pb−Free) 4000 Tape & Reel NCP582LXV29T1G* Active Low 2.9 F29A SOT−563 (Pb−Free) 4000 Tape & Reel NCP582LXV30T1G* Active Low 3.0 F30A SOT−563 (Pb−Free) 4000 Tape & Reel NCP582LXV33T1G* Active Low 3.3 F33A SOT−563 (Pb−Free) 4000 Tape & Reel *Samples and production start 1Q05. †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. http://onsemi.com 12 NCP582 PACKAGE DIMENSIONS SOT−563 XV SUFFIX CASE 463A−01 ISSUE D NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETERS A 3. MAXIMUM LEAD THICKNESS INCLUDES C LEAD FINISH THICKNESS. MINIMUM LEAD −X− K THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 6 5 4 MILLIMETERS INCHES B DIM MIN MAX MIN MAX S A 1.50 1.70 0.059 0.067 −Y− B 1.10 1.30 0.043 0.051 12 3 C 0.50 0.60 0.020 0.024 D 0.17 0.27 0.007 0.011 G 0.50 BSC 0.020 BSC D 6 5 PL J J 0.08 0.18 0.003 0.007 G M 0.08 (0.003) X Y K 0.10 0.30 0.004 0.012 S 1.50 1.70 0.059 0.067 SOLDERING FOOTPRINT* 0.3 0.0118 0.45 0.0177 1.0 0.0394 1.35 0.0531 0.5 0.5 0.0197 0.0197 mm � � SCALE 20:1 inches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 13 NCP582 PACKAGE DIMENSIONS SC−82AB SQ SUFFIX CASE 419C−02 ISSUE C NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. A 2. CONTROLLING DIMENSION: MILLIMETER. 3. 419C−01 OBSOLETE. NEW STANDARD IS 419C−02. G 4. DIMENSIONS A AND B DO NOT INCLUDE C MOLD FLASH, PROTRUSIONS, OR GATE D 3 PL N BURRS. MILLIMETERS INCHES DIM MIN MAX MIN MAX 4 3 A 1.8 2.2 0.071 0.087 K B 1.15 1.35 0.045 0.053 S B C 0.8 1.1 0.031 0.043 12 D 0.2 0.4 0.008 0.016 F 0.3 0.5 0.012 0.020 G 1.1 1.5 0.043 0.059 H H 0.0 0.1 0.000 0.004 F J 0.10 0.26 0.004 0.010 J L K 0.1 --- 0.004 --- 0.05 (0.002) L 0.05 BSC 0.002 BSC N 0.2 REF 0.008 REF S 1.8 2.4 0.07 0.09 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800−282−9855 Toll Free ON Semiconductor Website: http://onsemi.com Literature Distribution Center for ON Semiconductor USA/Canada Order Literature: http://www.onsemi.com/litorder P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Japan: ON Semiconductor, Japan Customer Focus Center Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada For additional information, please contact your 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada local Sales Representative. Phone: 81−3−5773−3850 Email: orderlit@onsemi.com NCP582/D http://onsemi.com 14
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the NCP582DSQ18T1G have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Manufacturers

What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods