Elite.Parts Manufacturers O ON SEMICONDUCTOR CAT28F020LI12-ND
About product Specifications Features Datasheet FAQ

ON SEMICONDUCTOR CAT28F020LI12-ND

Image of ON SEMICONDUCTOR CAT28F020LI12-ND

Description

ON Semiconductor CAT28F020LI12-ND Memory Module - 2M (256Kx8bit) 5V 32 Pin Dip

Part Number

CAT28F020LI12-ND

Price

Request Quote

Manufacturer

ON SEMICONDUCTOR

Lead Time

Request Quote

Category

PRODUCTS - C

Specifications

Interface

Parallel (Byte-wide)

Lead Free Status

Lead Free

Lead Soldering Temperature (10 secs)

300°C

Memory Size

2M (256K x 8)

Memory Type

FLASH

Operating Temperature

-40°C ~ 85°C

Output Short Circuit Current(2)

100 mA

Package / Case

32-DIP (0.600", 15.24mm)

Package Power Dissipation Capability (TA - 25°C)

1.0 W

Packaging

Tube

RoHS Status

RoHS Compliant

Speed

120ns

Storage Temperature

–65°C to +150°C

Temperature Under Bias

–45°C to +130°C

VCC with Respect to Ground(1)

–2.0V to +7.0V

Voltage - Supply

4.5 V ~ 5.5 V

Voltage on Any Pin with Respect to Ground(1)

–2.0V to +VCC + 2.0V

Voltage on Pin A9 with Respect to Ground(1)

–2.0V to +13.5V

VPP with Respect to Ground during Program/Erase(1)

–2.0V to +14.0V

Features

Datasheet

pdf file

On Semiconductor-CAT28F020-D-Datasheet-1566053955.pdf

353 KiB

Extracted Text

CAT28F020 Licensed Intel 2 Megabit CMOS Flash Memory second source FEATURES Commercial, industrial and automotive Fast read access time: 90/120 ns temperature ranges Low power CMOS dissipation:Stop timer for program/erase – Active: 30 mA max (CMOS/TTL levels) On-chip address and data latches – Standby: 1 mA max (TTL levels) JEDEC standard pinouts: – Standby: 100 μA max (CMOS levels) – 32-pin DIP High speed programming: – 32-pin PLCC – 10 μs per byte – 32-pin TSOP (8 x 20) – 4 seconds typical chip program 100,000 program/erase cycles 0.5 seconds typical chip-erase 10 year data retention 12.0V ± 5% programming and erase voltage Electronic signature DESCRIPTION using a two write cycle scheme. Address and Data are The CAT28F020 is a high speed 256K x 8-bit electrically latched to free the I/O bus and address bus during the erasable and reprogrammable Flash memory ideally write operation. suited for applications requiring in-system or after-sale code updates. Electrical erasure of the full memory The CAT28F020 is manufactured using Catalyst’s contents is achieved typically within 0.5 second. advanced CMOS floating gate technology. It is designed to endure 100,000 program/erase cycles and has a data It is pin and Read timing compatible with standard 2 retention of 10 years. The device is available in JEDEC EPROM and E PROM devices. Programming and approved 32-pin plastic DIP, 32-pin PLCC or 32-pin Erase are performed through an operation and verify TSOP packages. algorithm. The instructions are input via the I/O bus, BLOCK DIAGRAM I/O –I/O 0 7 I/O BUFFERS ERASE VOLTAGE SWITCH WE DATA SENSE COMMAND PROGRAM VOLTAGE CE, OE LOGIC LATCH AMP REGISTER SWITCH CE OE Y-GATING Y-DECODER 2,097,152 BIT A –A 0 17 MEMORY X-DECODER ARRAY VOLTAGE VERIFY 5115 FHD F02 SWITCH © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 1 Characteristics subject to change without notice ADDRESS LATCH CAT28F020 PIN CONFIGURATION PIN FUNCTIONS DIP Package (L) PLCC Package (N, G) Pin Name Type Function A –A Input Address Inputs for V 1 32 V 0 17 PP CC memory addressing A 2 31 WE 16 A 3 30 A 15 17 4321 323130 I/O –I/O I/O Data Input/Output 0 7 A 4 29 A 5 29 A A 12 14 7 14 CE Input Chip Enable A 5 28 A 6 28 A A 7 13 6 13 A 6 27 A 7 27 A A 6 8 5 8 OE Input Output Enable A 7 26 A 8 26 A A 5 9 4 9 WE Input Write Enable A 8 25 A 9 25 A A 4 11 3 11 A 9 24 OE 10 24 A OE 3 2 V Voltage Supply CC A 10 23 A 11 23 A A 2 10 1 10 V Ground A 11 22 CE 12 22 SS A CE 1 0 A 12 21 I/O 13 21 I/O I/O 0 7 0 7 V Program/Erase PP 14 15 16 17 18 19 20 I/O 13 20 I/O 0 6 Voltage Supply I/O 14 19 I/O 1 5 I/O 15 18 I/O 2 4 V 16 17 I/O SS 3 5115 FHD F01 TSOP Package (Standard Pinout) (T, H) A 1 32 OE 11 A 2 31 A 9 10 3 30 CE A 8 4 29 A I/O 13 7 5 28 A I/O 14 6 6 27 A I/O 17 5 7 26 WE I/O 4 8 25 V I/O CC 3 9 24 V V PP SS 10 23 A I/O 16 2 11 22 A I/O 15 1 12 21 A I/O 12 0 13 20 A A 7 0 A 14 19 A 6 1 A 15 18 A 5 2 A 16 17 A 4 3 TSOP Package (Reverse Pinout) (TR, HR) A OE 1 32 11 A 31 A 2 10 9 CE 3 30 A 8 I/O 4 29 A 7 13 5 28 A I/O 6 14 6 27 A I/O 5 17 7 26 WE I/O 4 8 25 V I/O 3 CC 9 24 V V SS PP 10 23 A I/O 2 16 11 22 A I/O 1 15 12 21 A I/O 0 12 13 20 A A 0 7 14 19 A A 1 6 15 18 A A 5 2 16 17 A A 4 3 5115 FHD F14 © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 2 Characteristics subject to change without notice I/O A 1 12 I/O A 2 15 V A SS 16 I/O V 3 PP I/O V 4 CC I/O WE 5 I/O A 6 17 CAT28F020 ABSOLUTE MAXIMUM RATINGS* *COMMENT Temperature Under Bias ................. –45 °C to +130°C Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Storage Temperature....................... –65 °C to +150°C These are stress ratings only, and functional operation of Voltage on Any Pin with the device at these or any other conditions outside of those (1) Respect to Ground ........... –2.0V to +V CC + 2.0V listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for Voltage on Pin A with 9 (1) extended periods may affect device performance and Respect to Ground ................... –2.0V to +13.5V reliability. V with Respect to Ground PP (1) during Program/Erase .............. –2.0V to +14.0V (1) V with Respect to Ground ............ –2.0V to +7.0V CC Package Power Dissipation Capability (T = 25°C) .................................. 1.0 W A Lead Soldering Temperature (10 secs) ............ 300°C (2) Output Short Circuit Current ........................ 100 mA RELIABILITY CHARACTERISTICS Symbol Parameter Test Method Min Typ Max Units (3) N Endurance MIL-STD-883, Test Method 1033 100K Cycles/Byte END (3) T Data Retention MIL-STD-883, Test Method 1008 10 Years DR (3) V ESD Susceptibility MIL-STD-883, Test Method 3015 2000 Volts ZAP (3)(4) I Latch-Up JEDEC Standard 17 100 mA LTH CAPACITANCE T = 25°C, f = 1.0 MHz A Symbol Test Conditions Min Typ Max Units (3) C Input Pin Capacitance V = 0V 6 pF IN IN (3) C Output Pin Capacitance V = 0V 10 pF OUT OUT (3) C V Supply Capacitance V = 0V 25 pF VPP PP PP Note: 1. The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Max imum DC voltage on output pins is V +0.5V, which may overshoot to V + 2.0V for periods of less than 20ns. CC CC 2. Output shorted for no more than one second. No more than one output shorted at a time. 3. This parameter is tested initially and after a design or process change that affects the parameter. 4. Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to V +1V. CC © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 3 Characteristics subject to change without notice CAT28F020 D.C. OPERATING CHARACTERISTICS V = +5V ±10%, unless otherwise specified. (See Note 2) CC Symbol Parameter Test Conditions Min Typ Max Unit I Input Leakage Current V = V or V ±1 μA LI IN CC SS V = 5.5V, OE = V CC IH I Output Leakage Current V = V or V , ±1 μA LO OUT CC SS V = 5.5V, OE = V CC IH I V Standby Current CMOS CE = V ±0.5V, 100 μA SB1 CC CC V = 5.5V CC I V Standby Current TTL CE = V , V = 5.5V 1 mA SB2 CC IH CC I V Active Read Current V = 5.5V, CE = V,30mA CC1 CC CC IL I = 0mA, f = 6 MHz OUT (1) I V Programming Current V = 5.5V, 15 mA CC2 CC CC Programming in Progress (1) I V Erase Current V = 5.5V, 15 mA CC3 CC CC Erasure in Progress (1) I V Prog./Erase Verify Current V = 5.5V, Program or 15 mA CC4 CC CC Erase Verify in Progress I V Standby Current V = V ±10 μA PPS PP PP PPL I V Read Current V = V 200 μA PP1 PP PP PPH (1) I V Programming Current V = V,30mA PP2 PP PP PPH Programming in Progress (1) I V Erase Current V = V,30mA PP3 PP PP PPH Erasure in Progress (1) I V Prog./Erase Verify Current V = V , Program or 5 mA PP4 PP PP PPH Erase Verify in Progress V Input Low Level TTL -0.5 0.8 V IL V Input Low Level CMOS -0.5 0.8 V ILC (2) V Output Low Level I = 5.8mA, V = 4.5V 0.45 V OL OL CC V Input High Level TTL 2 V +0.5 V IH CC V Input High Level CMOS V *0.7 V +0.5 V IHC CC CC (2) V Output High Level TTL I = -2.5mA, V = 4.5V 2.4 V OH1 OH CC (2) V Output High Level CMOS I = -400μA, V = 4.5V V -0.4 V OH2 OH CC CC V A Signature Voltage A = V 11.4 13 V ID 9 9 ID (1) I A Signature Current A = V 200 μA ID 9 9 ID V V Erase/Prog. Lockout Voltage 2.5 V LO CC Note: 1. This parameter is tested initially and after a design or process change that affects the parameter. 2. CAT28F020-90, V = 4.75 V. CCMIN © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 4 Characteristics subject to change without notice CAT28F020 SUPPLY CHARACTERISTICS Sr ymbolPn aramete Mp i Tx y Mt a Uni 25 8F020-9045 .7 5V . Ve CC VCC Supply Voltag 25 8F020-1245 . 5V . Vs PPLV0 PP During Read Operation 6V .5 Vm PPHV4 PP During Read/Erase/Progra 16 1. 1V 2. A.C. CHARACTERISTICS, Read Operation V = +5V ±10%, unless otherwise specified. (See Note 8) CC (7) (7) JEDEC Standard 28F020-90 28F020-12 Symbol Symbol Parameter Min Typ Max Min Typ Max Unit t t Read Cycle Time 90 120 ns AVAV RC t t CE Access Time 90 120 ns ELQV CE t t Address Access Time 90 120 ns AVQV ACC t t OE Access Time 35 50 ns GLQV OE t t Output Hold from Address OE/CE Change 0 0 ns AXQX OH (1)(6) t t OE to Output in Low-Z 0 0 ns GLQX OLZ (1)(6) t t CE to Output in Low-Z 0 0 ns ELQX LZ (1)(2) t t OE High to Output High-Z 30 30 ns GHQZ DF (1)(2) t t CE High to Output High-Z 40 40 ns EHQZ DF (1) t - Write Recovery Time Before Read 6 6 μs WHGL (3)(4)(5) Figure 1. A.C. Testing Input/Output Waveform 2.4 V 2.0 V INPUT PULSE LEVELS REFERENCE POINTS 0.8 V 0.45 V Testing Load Circuit (example) 1.3V 1N914 3.3K DEVICE UNDER OUT TEST C = 100 pF L C INCLUDES JIG CAPACITANCE L Note: 1. This parameter is tested initially and after a design or process change that affects the parameter. 2. Output floating (High-Z) is defined as the state where the external data line is no longer driven by the output buffer. 3. Input Rise and Fall Times (10% to 90%) < 10 ns. 4. Input Pulse Levels = 0.45 V and 2.4 V. For High Speed Input Pulse Levels 0.0 V and 3.0 V. 5. Input and Output Timing Reference = 0.8 V and 2.0 V. For High Speed Input and Output Timing Reference = 1.5 V. 6. Low-Z is defined as the state where the external data may be driven by the output buffer but may not be valid. 7. For load and reference points, see Fig. 1. 8. CAT28F020-90, V = 4.75 V. CCMIN © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 5 Characteristics subject to change without notice CAT28F020 A.C. CHARACTERISTICS, Program/Erase Operation V = +5V ±10%, unless otherwise specified. (See Note 6) CC JEDEC Standard 28F020-90 28F020-12 Symbol Symbol Parameter Min Typ Max Min Typ Max Unit t t Write Cycle Time 90 120 ns AVAV WC t t Address Setup Time 0 0 ns AVWL AS t t Address Hold Time 40 40 ns WLAX AH t t Data Setup Time 40 40 ns DVWH DS t t Data Hold Time 10 10 ns WHDX DH t t CE Setup Time 0 0 ns ELWL CS t t CE Hold Time 0 0 ns WHEH CH t t WE Pulse Width 40 40 ns WLWH WP t t WE High Pulse Width 20 20 ns WHWL WPH (2) t - Program Pulse Width 10 10 μs WHWH1 (2) t - Erase Pulse Width 9.5 9.5 ms WHWH2 t - Write Recovery Time Before Read 6 6 μs WHGL t - Read Recovery Time Before Write 0 0 μs GHWL t -V Setup Time to CE 100 100 ns VPEL PP (1) ERASE AND PROGRAMMING PERFORMANCE 28F020-90 28F020-12 Parameter Min Typ Max Min Typ Max Unit (3)(5) Chip Erase Time 0.5 10 0.5 10 sec (3)(4) Chip Program Time 4 25 4 25 sec Note: 1. Please refer to Supply characteristics for the value of V and V . The V supply can be either hardwired or switched. If V is switched, PPH PPL PP PP V can be ground, less than V + 2.0V or a no connect with a resistor tied to ground. PPL CC 2. Program and Erase operations are controlled by internal stop timers. 3. ‘Typicals’ are not guaranteed, but based on characterization data. Data taken at 25°C, 12.0V V . PP 4. Minimum byte programming time (excluding system overhead) is 16 μs (10 μs program + 6 μs write recovery), while maximum is 400 μs/ byte (16 μs x 25 loops). Max chip programming time is specified lower than the worst case allowed by the programming algorithm since most bytes program significantly faster than the worst case byte. 5. Excludes 00H Programming prior to Erasure. 6. CAT28F020-90, V = 4.75 V CCMIN © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 6 Characteristics subject to change without notice CAT28F020 (1) FUNCTION TABLE Pins Mode CE OE WE V I/O Notes PP Read V V V V D IL IL IH PPL OUT Output Disable V V V X High-Z IL IH IH Standby V XX V High-Z IH PPL Signature (MFG) V V V X 31H A = V , A = 12V IL IL IH 0 IL 9 Signature (Device) V V V X BDH A = V , A = 12V IL IL IH 0 IH 9 Program/Erase V V V V D See Command Table IL IH IL PPH IN Write Cycle V V V V D During Write Cycle IL IH IL PPH IN Read Cycle V V V V D During Write Cycle IL IL IH PPH OUT WRITE COMMAND TABLE Commands are written into the command register in one or two write cycles. The command register can be altered only when V is high and the instruction byte is latched on the rising edge of WE. Write cycles also internally latch PP addresses and data required for programming and erase operations. Pins First Bus Cycle Second Bus Cycle Mode Operation Address D Operation Address D D IN IN OUT Set Read Write X 00H Read A D IN OUT Read Sig. (MFG) Write X 90H Read 00 31H Read Sig. (Device) Write X 90H Read 01 BDH Erase Write X 20H Write X 20H Erase Verify Write A A0H Read X D IN OUT Program Write X 40H Write A D IN IN Program Verify Write X C0H Read X D OUT Reset Write X FFH Write X FFH Note: 1. Logic Levels: X = Logic ‘Do not care’ (V , V , V , V ) IH IL PPL PPH © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 7 Characteristics subject to change without notice CAT28F020 The conventional mode is entered as a regular READ READ OPERATIONS mode by driving the CE and OE pins low (with WE high), Read Mode and applying the required high voltage on address pin A 9 while all other address lines are held at V . IL A Read operation is performed with both CE and OE low and with WE high. V can be either high or low, PP A Read cycle from address 0000H retrieves the binary however, if V is high, the Set READ command has to PP code for the IC manufacturer on outputs I/O0 to I/O7: be sent before reading data (see Write Operations). The data retrieved from the I/O pins reflects the contents of CATALYST Code = 00110001 (31H) the memory location corresponding to the state of the 18 A Read cycle from address 0001H retrieves the binary address pins. The respective timing waveforms for the code for the device on outputs I/O to I/O . 0 7 read operation are shown in Figure 3. Refer to the AC Read characteristics for specific timing parameters. 28F020 Code = 1011 1101 (BDH) Signature Mode Standby Mode The signature mode allows the user to identify the IC With CE at a logic-high level, the CAT28F020 is placed manufacturer and the type of device while the device in a standby mode where most of the device circuitry is resides in the target system. This mode can be activated disabled, thereby substantially reducing power con- in either of two ways; through the conventional method sumption. The outputs are placed in a high-impedance of applying a high voltage (12V) to address pin A or by 9 state. sending an instruction to the command register (see Write Operations). Figure 3. A.C. Timing for Read Operation POWER UP STANDBY DEVICE AND OUPUTS DATA VALID STANDBY POWER DOWN ADDRESS SELECTION ENABLED ADDRESSES ADDRESS STABLE t (t ) AVAV RC CE (E) t (t ) EHQZ DF OE (G) t t (t ) WHGL GHQZ DF t (t ) WE (W) GLQV OE t (t ) ELQV CE t (t ) t (t ) AXQX OH GLQX OLZ t (t ) ELQX LZ HIGH-Z HIGH-Z DATA (I/O) OUTPUT VALID t (t ) AVQV ACC 28F020 F05 © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 8 Characteristics subject to change without notice CAT28F020 A Read cycle from address 0001H retrieves the binary WRITE OPERATIONS code for the device on outputs I/O to I/O . 0 7 The following operations are initiated by observing the 28F020 Code = 1011 1101 (BDH) sequence specified in the Write Command Table. Erase Mode Read Mode During the first Write cycle, the command 20H is written The device can be put into a standard READ mode by into the command register. In order to commence the initiating a write cycle with 00H on the data bus. The erase operation, the identical command of 20H has to be subsequent read cycles will be performed similar to a 2 written again into the register. This two-step process standard EPROM or E PROM Read. ensures against accidental erasure of the memory con- Signature Mode tents. The final erase cycle will be stopped at the rising edge of WE, at which time the Erase Verify command An alternative method for reading device signature (see (A0H) is sent to the command register. During this cycle, Read Operations Signature Mode), is initiated by writing the address to be verified is sent to the address bus and the code 90H into the command register while keeping latched when WE goes low. An integrated stop timer V high. A read cycle from address 0000H with CE and PP allows for automatic timing control over this operation, OE low (and WE high) will output the device signature. eliminating the need for a maximum erase timing speci- CATALYST Code = 00110001 (31H) fication. Refer to AC Characteristics (Program/Erase) for specific timing parameters. Figure 4. A.C. Timing for Erase Operation SETUP ERASE ERASE ERASING ERASE VERIFY ERASE V POWER-DOWN/ V POWER-UP CC CC COMMAND COMMAND COMMAND VERIFICATION STANDBY & STANDBY ADDRESSES t t t t WC WC WC RC t t AS AH CE (E) t t CS CH t t CH EHQZ t t CH CS OE (G) t GHWL t t t WHWH2 WHGL DF t WPH WE (W) t t t t WP WP WP OE t t t t DH DH DH OH t t t t DS DS OLZ DS HIGH-Z DATA IN DATA IN DATA IN DATA (I/O) = 20H = 20H = A0H VALID t LZ DATA OUT t CE 5.0V V CC 0V t VPEL V PPH V PP V PPL 28F020 F11 © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 9 Characteristics subject to change without notice CAT28F020 (1) Figure 5. Chip Erase Algorithm BUS START ERASURE COMMAND COMMENTS OPERATION V RAMPS TO V PP PPH APPLY V PPH (OR V HARDWIRED) PP ALL BYTES SHALL BE PROGRAM ALL PROGRAMMED TO 00 STANDBY BYTES TO 00H BEFORE AN ERASE OPERATION INITIALIZE INITIALIZE ADDRESS ADDRESS INITIALIZE PLSCNT = PULSE COUNT PLSCNT = 0 ACTUAL ERASE WRITE ERASE WRITE ERASE NEEDS 10ms PULSE, DATA=20H SETUP COMMAND DATA = 20H DATA = 20H WRITE ERASE WRITE ERASE DATA = 20H COMMAND TIME OUT 10ms WAIT ADDRESS = BYTE TO VERIFY WRITE ERASE ERASE WRITE DATA = 20H; A0H VERIFY COMMAND VERIFY STOPS ERASE OPERATION TIME OUT 6μs WAIT INCREMENT ADDRESS READ DATA READ READ BYTE TO FROM DEVICE VERIFY ERASURE NO NO DATA = INC PLSCNT COMPARE OUTPUT TO FF STANDBY FFH? = 3000 ? =1000 ? INCREMENT PULSE COUNT YES YES NO LAST ADDRESS? YES DATA = 00H WRITE READ RESETS THE REGISTER WRITE READ COMMAND FOR READ OPERATION V RAMPS TO V PP PPL APPLY V APPLY V STANDBY PPL PPL (OR V HARDWIRED) PP ERASURE ERASE COMPLETED ERROR Note: 5108 FHD F10 (1) The algorithm MUST BE FOLLOWED to ensure proper and reliable operation of the device. © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 10 Characteristics subject to change without notice CAT28F020 Erase-Verify Mode Program-Verify Mode The Erase-verify operation is performed on every byte A Program-verify cycle is performed to ensure that all after each erase pulse to verify that the bits have been bits have been correctly programmed following each erased. byte programming operation. The specific address is already latched from the write cycle just completed, and Programming Mode stays latched until the verify is completed. The Program- The programming operation is initiated using the pro- verify operation is initiated by writing C0H into the gramming algorithm of Figure 7. During the first write command register. An internal reference generates the cycle, the command 40H is written into the command necessary high voltages so that the user does not need register. During the second write cycle, the address of to modify V . Refer to AC Characteristics (Program/ CC the memory location to be programmed is latched on the Erase) for specific timing parameters. falling edge of WE, while the data is latched on the rising edge of WE. The program operation terminates with the next rising edge of WE. An integrated stop timer allows for automatic timing control over this operation, eliminat- ing the need for a maximum program timing specifica- tion. Refer to AC Characteristics (Program/Erase) for specific timing parameters. Figure 6. A.C. Timing for Programming Operation V POWER-UP SETUP PROGRAM LATCH ADDRESS PROGRAM PROGRAM V POWER-DOWN/ CC CC COMMAND & DATA VERIFY VERIFICATION STANDBY & STANDBY PROGRAMMING COMMAND ADDRESSES t t t WC WC RC t t AS AH CE (E) t t CS CH t t CH EHQZ t t CH CS OE (G) t GHWL t t t WHWH1 WHGL DF t WPH WE (W) t t t t WP WP WP OE t t t t DH DH DH OH t t t t DS DS OLZ DS HIGH-Z DATA IN DATA IN DATA (I/O) DATA IN = 40H = C0H VALID t LZ DATA OUT t CE 5.0V V CC 0V t VPEL V PPH V PP V PPL 28F020 F07 © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 11 Characteristics subject to change without notice CAT28F020 (1) Figure 7. Programming Algorithm START BUS COMMAND COMMENTS PROGRAMMING OPERATION V RAMPS TO V APPLY V PP PPH STANDBY PPH (OR V HARDWIRED) PP INITIALIZE INITIALIZE ADDRESS ADDRESS INITIALIZE PULSE COUNT PLSCNT = 0 PLSCNT = PULSE COUNT WRITE SETUP 1ST WRITE WRITE DATA = 40H PROG. COMMAND CYCLE SETUP WRITE PROG. CMD 2ND WRITE PROGRAM VALID ADDRESS AND DATA ADDR AND DATA CYCLE TIME OUT 10μs WAIT WRITE PROGRAM 1ST WRITE PROGRAM DATA = C0H VERIFY COMMAND CYCLE VERIFY TIME OUT 6μs WAIT READ DATA READ BYTE TO VERIFY READ FROM DEVICE PROGRAMMING NO INC NO VERIFY COMPARE DATA OUTPUT STANDBY PLSCNT DATA ? TO DATA EXPECTED = 25 ? YES YES LAST NO INCREMENT ADDRESS? ADDRESS YES DATA = 00H WRITE READ 1ST WRITE READ SETS THE REGISTER FOR COMMAND CYCLE READ OPERATION V RAMPS TO V APPLY V APPLY V PP PPL STANDBY PPL PPL (OR V HARDWIRED) PP PROGRAMMING PROGRAM COMPLETED ERROR Note: (1) The algorithm MUST BE FOLLOWED to ensure proper and reliable operation of the device. 5108 FHD F06 © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 12 Characteristics subject to change without notice CAT28F020 Abort/Reset POWER SUPPLY DECOUPLING An Abort/Reset command is available to allow the user To reduce the effect of transient power supply voltage to safely abort an erase or program sequence. Two spikes, it is good practice to use a 0.1μF ceramic consecutive program cycles with FFH on the data bus capacitor between V and V and V and V . These CC SS PP SS will abort an erase or a program operation. The abort/ high-frequency capacitors should be placed as close as reset operation can interrupt at any time in a program or possible to the device for optimum decoupling. erase operation and the device is reset to the Read Mode. POWER UP/DOWN PROTECTION The CAT28F020 offers protection against inadvertent programming during V and V power transitions. PP CC When powering up the device there is no power-on sequencing necessary. In other words, V and V PP CC may power up in any order. Additionally V may be PP hardwired to V independent of the state of V and PPH CC any power up/down cycling. The internal command register of the CAT28F020 is reset to the Read Mode on power up. Figure 8. Alternate A.C. Timing for Program Operation SETUP PROGRAM LATCH ADDRESS PROGRAM PROGRAM V POWER-DOWN/ V POWER-UP CC CC COMMAND & DATA VERIFY VERIFICATION STANDBY & STANDBY PROGRAMMING COMMAND ADDRESSES t t t WC WC RC t t AVEL ELAX WE (W) t t WLEL EHWH t t t WLEL EHWH EHQZ t t EHWH WLEL OE (G) t t t t EHEH EHGL DF GHEL t EHEL CE (E) t t t ELEH ELEH OE t t t t EHDX EHDX EHDX OH t t t t DVEH OLZ DVEH DVEH HIGH-Z DATA IN DATA IN DATA (I/O) DATA IN = 40H = C0H VALID t LZ DATA OUT t CE 5.0V V CC 0V t VPEL V PPH V PP V PPL 28F020 F09 28F020 F09 © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 13 Characteristics subject to change without notice CAT28F020 ALTERNATE CE CE CE-CONTROLLED WRITES CE CE JEDEC Standard 28F020-90 28F020-12 Symbol Symbol Parameter Min Typ Max Min Typ Max Unit t t Write Cycle Time 90 120 ns AVAV WC t t Address Setup Time 0 0 ns AVEL AS t t Address Hold Time 40 40 ns ELAX AH t t Data Setup Time 40 40 ns DVEH DS t t Data Hold Time 10 10 ns EHDX DH t — Write Recovery Time Before Read 6 6 μs EHGL t — Read Recovery Time Before Write 0 0 μs GHEL t t WE Setup Time Before CE 00 ns WLEL WS t — WE Hold Time After CE 00 ns EHWH t t Write Pulse Width 40 40 ns ELEH CP t t Write Pulse Width High 20 20 ns EHEL CPH t —V Setup Time to CE Low 100 100 ns VPEL PP © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 14 Characteristics subject to change without notice CAT28F020 (1) EXAMPLE OF ORDERING INFORMATION Prefix Device # Suffix CAT 28F020 N I -12 T Product Temperature Range Tape & Reel Number T: 500/Reel (3) Optional Package Speed (2) Company ID N: PLCC 90: 90ns (2) T: TSOP (8mmx20mm) 12: 120ns (2) TR: TSOP (Reverse Pinout) G: PLCC (Lead free, Halogen free) L: PDIP (Lead free, Halogen free) H: TSOP (Lead free, Halogen free) HR: TSOP (Reverse Pinout) (Lead free, Halogen free) ORDERING INFORMATION Orderable Part Numbers (for Pb-Free Devices) CT AT28F020GA-12T CAT28F020HRA-12 CT AT28F020GA-90T CAT28F020HRA-90 CT AT28F020GI-12T CAT28F020HRI-12 CT AT28F020GI-90T CAT28F020HRI-90 C2 AT28F020HA-12T CAT28F020LA1 C0 AT28F020HA-90T CAT28F020LA9 C2 AT28F020HI-12T CAT28F020LI1 C0 AT28F020HI-90T CAT28F020LI9 Notes: (1) The device used in the above example is a CAT28F020NI-12T (PLCC, Industrial Temperature, 120 ns access time, Tape & Reel). (2) Solder-plate (tin-lead) packages, contact Factory for availability. (3) -40°C to +125°C is available upon request. © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 15 Characteristics subject to change without notice CAT28F020 REVISION HISTORY Date Revision Description 1-May-02 A Initial issue 10-Feb-04 B Change V for CAT28F020-90 to 4.75 V from 4.5 V CCMIN 01-Jul-04 C Added Green Packages in all areas. 15-Oct-08 D Eliminate PDIP SnPb package. 17-Nov-08 E Change logo and fine print to ON Semiconductor 31-Jul-09 F Update Absolute Maximum Ratings Update Example of Ordering Information Update Ordering Information table ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800-282-9855 ON Semiconductor Website: www.onsemi.com Literature Distribution Center for ON Semiconductor Toll Free P.O. Box 5163, Denver, Colorado 80217 USA USA/Canada Order Literature: http://www.onsemi.com/orderlit Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada For additional information, please contact your local Phone: 421 33 790 2910 Email: orderlit@onsemi.com Sales Representative Japan Customer Focus Center: Phone: 81-3-5773-3850 © 2009 SCILLC. All rights reserved. Doc. No. MD-1029, Rev. F 16 Characteristics subject to change without notice

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the CAT28F020LI12-ND have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

Sensitive Gate Silicon Controlled Rectifiers

Silicon Controlled Rectifier 4 Amperes RMS 200 Thru 600volts Reverse Blocking Triode Thyristors

SCR Thyristor

SCR Thyristor

SCR Thyristor

THYRISTOR, 2.5A 400V TO-126 RoHS Compliant: No