OMRON Host Link Cables

Host Link Cables (RS-232C Cables for Programmable Controller) XW2Z-@@@P-V/S-V/S-CV/T CSM_XW2Z-___P-V_S-V_S-CV_T_DS_E_1_1 Ideal Cables for between Programmable Controllers and Host Computers SYSMAC PLC Host • Personal computer • CQM1 • C Series • Factory Intelligent Terminal • Programmable Terminal • CV Series • CVM1 XW2Z Host Link Cable Ordering Information SYSMAC Host Link Cable (RS-232C Cable for Programmable Controllers) SYSMAC PLC Units Host Wiring patterns Cable length L * Model D-sub, 25-pin Plug D-sub, 9-pin Socket PLC Host Shield C20-LK201-V1 Connector Hood FG Connector Hood FG 2 m XW2Z-200P-V C500-LK203 FG 1 1 --- SD 2 2 RD C500-LK201-V1 RD 3 3 SD C120-LK201-V1 RS 4 4 ER C200H-LK201 CS 5 5 SG CV500-LK201 DR 6 6 DR 5 m XW2Z-500P-V (Port 1, full-duplex mode) SG 7 7 RS 8CS ER 20 9 --- C200HS-CPU31/33/21/23 CQM1-CPU21 CQM1-CPU41 D-sub, 9-pin Plug D-sub, 9-pin Socket CQM1-CPU42 2 m XW2Z-200S-V CQM1-CPU43 PLC Host Shield CQM1-CPU44 Connector Hood FG Connector Hood FG CV500/1000/2000 --- 1 1 --- CVM1 SD 2 2 RD Personal CV500-LK201 RD 3 3 SD computer: (Communications port 2) RS 4 4 ER IBM PC/AT or C200HE-CPU42 CS 5 5 SG compatible C200HG-CPU43/63 --- 6 6 DR C200HX-CPU44/64 --- 77RS C200HW-COM02 5 m XW2Z-500S-V --- 8 8 CS C200HW-COM04 SG 9 9 --- C200HW-COM05 C200HW-COM06 CPM1-CIF01 D-sub, 9-pin Plug D-sub, 9-pin Socket PLC Host Shield Connector Hood FG Connector Hood FG 2 m XW2Z-200S-CV FG 1 1 --- SD 2 2 RD CJ-series CPU Units RD 3 3 SD CS-series CPU Units RS 4 4 ER Serial Communications Unit CS 5 5 SG --- 6 6 DR 5 m XW2Z-500S-CV DR 7 7RS ER 8 8CS SG 9 9 --- Programmable Terminal (PT): NT20S Cable SYSMAC PLC Units Host Wiring patterns Cable length L * Model CQM1-CPU21 CQM1-CPU41 CQM1-CPU42 CQM1-CPU43 2 m XW2Z-200T CQM1-CPU44 D-sub, 9-pin Plug D-sub, 9-pin Plug (Units with RS-232C port) C200HS-CPU31/33/21/23 PLC Host Programmable CV500/1000/2000-CPU01 Connector Hood FG Shield Connector Hood FG Terminal (PT): CVM1-CPU01/11 --- 1 1 --- NT20S CV500-LK201 SD 2 2 SD NT600S/NT620S/ (Communications port 2) RD 3 3 RD NT620C C200HE-CPU42 RS 4 4 RS C200HG-CPU43/63 NT30/NT30C CS 5 5 CS C200HX-CPU44/64 SG 9 9 SG 5 m XW2Z-500T C200HW-COM02 C200HW-COM04 C200HW-COM05 C200HW-COM06 CPM1-CIF01 *Cable length L L 1 ··· ··· XW2Z Ratings and Specifications Item Type XW2Z-@P/S/T Rated current 1 A Rated voltage 125 VAC Contact resistance 15 mΩ max. (at 20 mV, 100 mA max.) *1 Insulation resistance 100 MΩ min. (at 500 VDC) Dielectric strength 500 VAC for 1 min (leakage current: 1 mA max.) *2 Degree of protection IP00 Electrical protection class Class 0 Ambient operating −25 to 80°C temperature *1. Contact resistance of the Connector. *2. Dielectric strength of the Connector. Materials and Finish Item Part name Materials and finish Housing Polyamide resin (UL94V-0)/milky white Mating ends XM2A-0901 Contacts Brass/nickel base, 0.2-µm gold plating XM2A-2501 Connectors Terminals Shell Steel/nickel plated XM2S-0911/2511 Housing ABS resin/nickel plated Cable UL2464 Interface Cable AWG28 or the equivalent 2 Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: · Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. · Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. · Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof. Disclaimers CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased products. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. ERRORS AND OMISSIONS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. 2008.1 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2008 All Right Reserved.