CJ/CS Series ID Sensor Unit CJ1W-V680C11/-V680C12 CS1W-V680C11/-V680C12 CSM_C_1W-V680C1_DS_E_1_1 Communication Unit Dedicated for RFID V680 Allowing Direct Connection to OMRON PLC CJ/ CS/NJ-series „ Communication unit for connecting RFID V680-series, which can be used around the world, directly to PLC. „ Allows batch transfer of data up to 32 kbytes. Features • Easy reading and writing of data by simply setting parameters in PLC memory area. • Simpler device configuration compared to serial communication allows faster data processing. • Function Block (FB) library in Ladder Program facilitates generation of communication programs. Note: For system configuration, refer to V680-series catalog (Q151). For specification of controllers, refer to the manual of each controller. Ordering Information No. of unit Current consumption (A) External Type Appearance Connected ID System numbers Model power supply 5 V 24 V External used 1 unit 1 Head 0.26 0.13 * − CJ1W-V680C11 number CJ V680 Special − Series I/O Unit 2 unit 2 Heads 0.32 0.26 − CJ1W-V680C12 number No. of unit Current consumption (A) External Type Appearance Connected ID System numbers Model power supply 5 V 26 V External used 1 unit 1 Head − 0.26 0.13 * − CS1W-V680C11 number CS V680 Special Series I/O Unit 2 unit 2 Heads 24 VDC 0.32 − 0.36 CS1W-V680C12 number * When connected to the V680-H01-V2: 0.28 A 1 CJ1W-V680C11/-V680C12 CS1W-V680C11/-V680C12 General Specification Item Model CJ1W-V680C11 CJ1W-V680C12 CS1W-V680C11 CS1W-V680C12 Internal: 5 V 0.26 A 0.32 A 0.26 A 0.32 A Current Internal: − con- 0.13 A * 0.26 A 0.13 A * 24 V/26 V sumption External: 24 V−−− 0.36 A Ambient operating 0 to 55°C temperature Ambient storage tem- −20°C to 75°C perature Ambient operating hu- 10% to 90% (with no condensation) midity Insulation resistance 20 mΩ min. at 500 VDC Dielectric strength 1,000 VAC for 1 minute Degree of protection Mounted in panel (IP30) 2 10 to 57 Hz variable vibration, 0.075-mm double amplitude and 57 to 150 Hz variable vibration at 9.8 m/s Vibration resistance acceleration, with 10 sweeps in X, Y, and Z directions for 8 minutes each 2 Shock resistance 147 m/s in X, Y, and Z directions 3 times each Appearance 31 × 65 × 90 mm (excluding protrusions) 35 × 130 × 101 mm (excluding protrusions) Weight 120 g max. 130 g max. 180 g max. 300 g max. * When connected to the V680-H01-V2: 0.28 A. 2 CJ1W-V680C11/-V680C12 CS1W-V680C11/-V680C12 Performance Specifications For CJ1 Series Item Model CJ1W-V680C11 CJ1W-V680C12 Unit classification Special I/O Unit Influence on CPU Unit's 0.15 ms 0.3 ms cycle time CJ1-series CPU Rack or CJ1-series Expansion Rack Mounting location (Cannot be mounted to C200H Expansion I/O Racks or SYSMAC BUS Slave Racks.) Connectable Antennas V680-series Amplifiers and Antennas *1 Applicable RF Tags V680-series RF Tags No. of allocated units12 No. of allocated words 10 words 20 words Control protocol Special protocol Unit controls, communications CPU Unit to ID processing specification, data Sensor Unit Special I/O Unit Area in Constant data storage area specification CIO Area: CIO 2000 to exchange of 10 words/ Unit information, results CIO 2959 Unit ID Sensor Unit to information, processing results CPU Unit Data exchange monitor methods with CPU Unit System Settings, Auto Wait Time 100 words/Unit Setting, Write Protection Disable Special I/O Unit words in transferred when power CPU Unit to ID Setting, Antenna Connection DM Area: D20000 to is turned ON or when Sensor Unit Setting, Results Monitor Output, D29599 restarting the Unit Test Setting, Run/Test Switching Method Setting Data transfer quantity 2,048 bytes max. (160 bytes/scan) *2 2,048 bytes max./channel (160 bytes/scan) *2 Run Mode • Communications tests • Distance level measurements Operating modes • Read speed level measurements Test Mode • Write speed level measurements • Noise level measurements • Communications success rate measurements (1) CPU watchdog timer Diagnostic functions (2) Communications error detection with RF Tag (3) Antenna power supply error *1. V680-H01 and V680-H01-V2 can be connected to 1CH-type ID Sensor Units only. They are not supported by 2CH-type ID Sensor Units. *2. If using Intelligent I/O Instructions is specified as the data transfer method, up to 2,048 bytes can be transferred in one scan. 3 CJ1W-V680C11/-V680C12 CS1W-V680C11/-V680C12 For CS1 Series Item Model CS1W-V680C11 CS1W-V680C12 Unit classification Special I/O Unit Influence on CPU 0.15 ms 0.3 ms Unit's cycle time CS1-series CPU Rack or CS1-series Expansion Rack Mounting location (Cannot be mounted to C200H Expansion I/O Racks or SYSMAC BUS Slave Racks.) Connectable Antennas V680-series Amplifiers and Antennas *1 Applicable RF Tags V680-series RF Tags No. of allocated units12 No. of allocated words 10 words 20 words Control protocol Special protocol Unit controls, communications CPU Unit to ID processing specification, data Sensor Unit Special I/O Unit Area in Constant data storage area specification CIO Area: CIO 2000 to exchange of 10 words/ Unit information, results CIO 2959 Unit ID Sensor Unit to information, processing results CPU Unit Data exchange monitor methods with CPU Unit System Settings, Auto Wait Time 100 words/Unit Setting, Write Protection Disable Special I/O Unit words in transferred when power CPU Unit to ID Setting, Antenna Connection DM Area: D20000 to is turned ON or when Sensor Unit Setting, Results Monitor Output, D29599 restarting the Unit Test Setting, Run/Test Switching Method Setting Data transfer quantity 2,048 bytes max. (160 bytes/scan) *2 2,048 bytes max./channel (160 bytes/scan) *2 Run Mode • Communications tests • Distance level measurements Operating modes • Read speed level measurements Test Mode • Write speed level measurements • Noise level measurements • Communications success rate measurements (1) CPU watchdog timer Diagnostic functions (2) Communications error detection with RF Tag (3) Antenna power supply error *1. V680-H01 and V680-H01-V2 can be connected to 1CH-type ID Sensor Units only. They are not supported by 2CH-type ID Sensor Units. *2. If using Intelligent I/O Instructions is specified as the data transfer method, up to 2,048 bytes can be transferred in one scan. 4 CJ1W-V680C11/-V680C12 CS1W-V680C11/-V680C12 For NJ Series Item Model CJ1W-V680C11 CJ1W-V680C12 Unit classification Special I/O Unit Mounting location NJ-series CPU Rack or NJ-series Expansion Rack Connectable Antennas V680-series Amplifiers and Antennas * Applicable RF Tags V680-series RF Tags Run Mode • Communications tests • Distance level measurements Operating modes • Read speed level measurements Test Mode • Write speed level measurements • Noise level measurements • Communications success rate measurements Data exchange Data exchange by using I/O ports methods with CPU Unit (1) CPU watchdog timer Diagnostic functions (2) Communications error detection with RF Tag (3) Antenna power supply error * V680-H01 and V680-H01-V2 can be connected to 1CH-type ID Sensor Units only. They are not supported by 2CH-type ID Sensor Units. 5 CJ1W-V680C11/-V680C12 CS1W-V680C11/-V680C12 Communications Function Specifications Item Model CJ1W-V680C11 CJ1W-V680C12 (1) RF Tag Communications Speed (Normal Mode or High-speed Mode) (2) Write Verification Processing (3) Auto Wait Time Setting Communications (4) UID Addition Setting control (5) Write Protection Setting (6) Antenna Connection Setting (One-channel ID Sensor Unit (CJ1W-V680C11)) (7) Results Monitor Setting Read Read Write Write Bit Set/Bit Clear Bit Set/Bit Clear Mask Bit Write Mask Bit Write Calculation Write Calculation Write Data Fill Data Fill Commands Data Check Data Check Number of Writes Control Number of Writes Control Read with Error Correction Copy Write with Error Correction Read with Error Correction UID Read Write with Error Correction Noise Measurement UID Read Noise Measurement Single trigger Single auto Repeat auto Communications FIFO trigger * specification FIFO repeat * Multi-access trigger * Multi-access repeat * * FIFO trigger, FIFO repeat, Multi-access trigger, and Multi-access repeat specification cannot be used for communicating with V680-D1KP@@ RF Tags. Item Model CS1W-V680C11 CS1W-V680C12 (1) RF Tag Communications Speed (Normal Mode or High-speed Mode) (2) Write Verification Processing (3) Auto Wait Time Setting Communications (4) UID Addition Setting control (5) Write Protection Setting (6) Antenna Connection Setting (One-channel ID Sensor Unit (CS1W-V680C11)) (7) Results Monitor Setting Read Read Write Write Bit Set/Bit Clear Bit Set/Bit Clear Mask Bit Write Mask Bit Write Calculation Write Calculation Write Data Fill Data Fill Commands Data Check Data Check Number of Writes Control Number of Writes Control Read with Error Correction Copy Write with Error Correction Read with Error Correction UID Read Write with Error Correction Noise Measurement UID Read Noise Measurement Single trigger Single auto Repeat auto Communications FIFO trigger * specification FIFO repeat * Multi-access trigger * Multi-access repeat * * FIFO trigger, FIFO repeat, Multi-access trigger, and Multi-access repeat specification cannot be used for communicating with V680-D1KP@@ RF Tags. 6 CJ1W-V680C11/-V680C12 CS1W-V680C11/-V680C12 Connectable Units When using V680-HS51/-HS52/-HS63/-HS65 Antenna NJ System CJ System CS System Model Expansion Expansion Expansion CPU unit CPU unit CPU unit unit unit unit CJ1W-V680C11 4 units 6 units 4 units 4 units N/A N/A CJ1W-V680C12 2 units 3 units 2 units 2 units N/A N/A CS1W-V680C11 N/A N/A N/A N/A 9 units 9 units CS1W-V680C12 N/A N/A N/A N/A 10 units 10 units When using V680-H01-V2 Antenna NJ System CJ System CS System Model Expansion Expansion Expansion CPU unit CPU unit CPU unit unit unit unit CJ1W-V680C11 2 units 2 units 2 units 1 unit N/A N/A CS1W-V680C11 N/A N/A N/A N/A 4 units 4 units Dimensions (unit: mm) CS1W-V680C11 CJ1W-V680C11 Six operation indicators 123 65 Six operation indicators Switches 4.5 2.7 Switches 01 18.1 90 130 17.3 4.7 Connector 2.7 Connector 31 101 35 CS1W-V680C12 CJ1W-V680C12 Eight operation indicators 123 65 Switches Eight operation indicators 2.7 4.5 Switches 01 4.7 18.1 130 90 17.3 25 29.2 51 Connectors 2.7 8 31 Connectors 15 3.6 101 Terminals 35 With cover mounted: 16.5 Related Manuals Man. No Model Manual name Application Description Describes the following for the main ID Sensor Unit: V680 series • System configuration CS1W-V680C11 ID sensor units When connecting to OMRON • Data exchange with CPU units Z271 CS1W-V680C12 User’s Manual PLC CS/CJ-series • Functions of ID Sensor Unit CJ1W-V680C11 • Controlling ID Sensor Unit CJ1W-V680C12 • Operations when alarm is triggered Describes the following for the main ID Sensor Unit: • System configuration V680 series ID sensor units When connecting to OMRON • Data exchange with CPU units Z317 CJ1W-V680C11 User’s Manual PLC NJ-series • Functions of ID Sensor Unit CJ1W-V680C12 • Controlling ID Sensor Unit • Operations when alarm is triggered 7 Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:  Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.  Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations.  Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof. Disclaimers CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased products. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. ERRORS AND OMISSIONS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. 2012.1 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2012 All Right Reserved.