SOLID TANTALUM ELECTROLYTIC CAPACITORS Resin-molded Chip, Standard Series F93 Specifications Compliant to the RoHS directive (2002/95/EC). Item Performance Characteristics Category ˚C ˚C --55 to +125 (Rated temperature : +85 ) Temperature Range Capacitance Tolerance ±20%, ±10% (at 120Hz) Dissipation Factor (120Hz) Refer to next page ESR (100kHz) Refer to next page After 1 minute's application of rated voltage, leakage current • at 20˚C is not more than 0.01CV or 0.5µA, whichever is greater. • After 1 minute's application of rated voltage, leakage current Leakage Current at 85˚C is not more than 0.1CV or 5µA, whichever is greater. • After 1 minute's application of derated voltage, leakage current at 125˚C is not more than 0.125CV or 6.3µA, whichever is greater. +15% Max. (at +125˚C) Capacitance Change +10% Max. (at +85˚C) by Temperature --10% Max. (at --55˚C) At 40˚C 90 to 95% R.H. 500 hours (No voltage applied) ... Damp Heat Capacitance Change Refer to next page (* 1) ........ (Steady State) Dissipation Factor Initial specified value or less Type numbering system (Example: 10V 10µF) .......... Leakage Current Initial specified value or less 55˚C / +125˚C 30 minutes each 5 cycles 1 2 3 4 5 6 7 8 9 10 11 -- ... Capacitance Change Refer to next page (* 1) Taping code F 9 3 1 A 1 0 6 M A Temperature Cycles (Refer to page 323 for details) ........ Dissipation Factor Initial specified value or less .......... Case code Leakage Current Initial specified value or less Capacitance tolerance 10 seconds reflow at 260˚C , 5 seconds immersion at 260˚C Rated capacitance ... Resistance Rated voltage Capacitance Change Refer to next page (* 1) ........ Series to Soldering Heat Dissipation Factor Initial specified value or less .......... Leakage Current Initial specified value or less Drawing After application of surge voltage in series with a 33Ω resistor at the rate of A • B Case C • N Case 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85˚C,capacitors meet the characteristics requirements listed below. ∗ Surge ..... Capacitance Change Refer to next page (* 1) L.........W1LDissipation Factor Initial specified value or lessW1 ........... Leakage Current Initial specified value or less HHAfter 2000 hours' application of rated voltage in series with a 3Ω resistor at 85 , or derated voltage in series with a 3Ω resistor at 125 , ˚C ˚C capacitors meet the characteristic requirements listed below. ∗ Endurance ...... Capacitance Change Refer to next page (* 1) ..........W2Dissipation Factor Initial specified value or lessW2 ............ Leakage Current Initial specified value or less SSSSAfter applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body which has no Dimensions (mm) electrode and has been soldered Shear Test beforehand on a substrate, there shall be Case code L W W HS 1 2¥5N(0.51kgf)found neither exfoliation nor its sign at the A 3.2 ±0.2 1.6 ±0.2 1.2 ±0.1 1.6 ±0.2 0.8 ±0.2 For10–1secondsterminal electrode. B 3.5 ±0.2 2.8 ±0.2 2.2 ±0.1 1.9 ±0.2 0.8 ±0.2 Keeping a capacitor surface-mounted on a substrate upside down C 6.0 ±0.2 3.2 ±0.2 2.2 ±0.1 2.5 ±0.2 1.3 ±0.2 and supporting the substrate at both of the opposite bottom points N 7.3 ± 0.2 4.3 ± 0.2 2.4 ± 0.1 2.8 ± 0.2 1.3 ± 0.2 45mm apart from the center of the 20capacitor, the pressure strength isR230 applied with a specified jig at the Terminal Strength center of the substrate so that the Marking substrate may bend by 1mm asmmA Case B Case C Case N Case1illustrated. Then, there shall be found 4545 no remarkable abnormality on the 22 C685 capacitor terminals. 16V ∗ As for the surge and derated voltage at 125˚C, refer to page 322 for details. We can supply the type of compliance to AEC-Q200. Capacitance (μF) Rated voltage (V) (Rated voltage code) (Capacitance code) Rated voltage (V) Please contact to your local Nichicon sales office 2.5V e 20V D when these series are being designed in your application. 4V G E 25V 6.3V J 35V V 10V A 16V C Standard Ratings V 4 6.3 10 16 20 25 35 Cap. (µF) Code 0G 0J 1A 1C 1D 1E 1V 0.68 684 A 1 105 A A A 1.5 155 A A • 2.2 225 A A A A B 3.3 335 A A A B • • • 4.7 475 A A B A B B C • 6.8 685 A A A B C • • • 10 106 A A A B A B B C C • 15 156 A A A B C C N • • • • • 22 226 A A A B A B C B C C N N • • • 33 336 A A A B B C C N N • • • • • • 47 476 A A B A B C (B) C N C N N • • 68 686 A A B B C N (N) • • • • • • 100 107 A B A B C B C N C N • • 150 157 B B C C N N • • • • 220 227 (A) B C B C N N N 330 337 C N N ( ) The series in parentheses are being developed. 470 477 N N Please contact to your local Nichicon sales office when these 680 687 N series are being designed in your application. CAT.8100A 47 16V 100 16V SOLID TANTALUM ELECTROLYTIC CAPACITORS F93 Standard Ratings Rated Leakage Disspation *1 Rated Leakage Disspation *1 Case ESR Case ESR Rated Volt Capacitance Part Number Current Factor ΔC/C Rated Volt Capacitance Part Number Current Factor ΔC/C code code (Ω@100kHz) (Ω@100kHz) (µF) (µA) (%@120Hz) (%) (µF) (µA) (%@120Hz) (%) 22 A F930G226MAA 0.9 6 2.5 ∗ 1 A F931C105MAA 0.5 4 7.5 ∗ 33 A F930G336MAA 1.3 8 2.5 ∗ 2.2 A F931C225MAA 0.5 4 5.0 ∗ 47 A F930G476MAA 1.9 18 2.5 ∗ 3.3 A F931C335MAA 0.5 4 4.5 ∗ 68 A F930G686MAA 2.7 24 2.5 ∗ 4.7 A F931C475MAA 0.8 6 4.0 ∗ 100 A F930G107MAA 4.0 30 2.0 ∗ 6.8 A F931C685MAA 1.1 6 3.5 ∗ 100 B F930G107MBA 4.0 14 0.9 ∗ 10 A F931C106MAA 1.6 6 3.0 ∗ 4V 150 B F930G157MBA 6.0 16 0.7 ∗ 10 B F931C106MBA 1.6 6 2.0 ∗ 220 B F930G227MBA 8.8 18 0.7 ∗ 15 A F931C156MAA 2.4 10 3.0 ∗ 220 C F930G227MCC 8.8 12 0.7 ∗ 15 B F931C156MBA 2.4 6 2.0 ∗ 330 C F930G337MCC 13.2 14 0.7 ∗ 22 A F931C226MAA 3.5 15 3.0 ±15 16V 470 N F930G477MNC 18.8 16 0.3 ∗ 22 B F931C226MBA 3.5 8 1.9 ∗ 680 N F930G687MNC 27.2 18 0.3 ∗ 22 C F931C226MCC 3.5 6 1.1 ∗ 10 A F930J106MAA 0.6 6 3.0 ∗ 33 B F931C336MBA 5.3 8 1.9 ∗ 15 A F930J156MAA 0.9 6 2.9 ∗ 33 C F931C336MCC 5.3 6 1.1 ∗ 22 A F930J226MAA 1.4 8 2.5 ∗ 47 C F931C476MCC 7.5 8 0.9 ∗ 33 A F930J336MAA 2.1 8 2.5 ∗ 47 N F931C476MNC 7.5 6 0.7 ∗ 47 A F930J476MAA 3.0 18 2.5 ∗ 68 N F931C686MNC 10.9 6 0.6 ∗ 47 B F930J476MBA 3.0 6 1.0 ∗ 100 C F931C107MCC 16.0 15 0.7 ±10 68 A F930J686MAA 4.3 20 2.0 ∗ 100 N F931C107MNC 16.0 10 0.6 ∗ 68 B F930J686MBA 4.3 8 1.0 ∗ 150 N F931C157MNC 24.0 15 0.6 ∗ ± 100 A F930J107MAA 6.3 35 2.0 15 220 N F931C227MNC 35.2 25 0.7 ±10 6.3V 100 B F930J107MBA 6.3 14 0.9 ∗ 2.2 A F931D225MAA 0.5 4 5.0 ∗ 100 C F930J107MCC 6.3 8 0.7 ∗ 3.3 A F931D335MAA 0.7 4 4.5 ∗ 150 B F930J157MBA 9.5 18 0.9 ∗ 4.7 A F931D475MAA 0.9 6 3.0 ∗ 150 C F930J157MCC 9.5 12 0.7 ∗ 4.7 B F931D475MBA 0.9 6 2.8 ∗ ± 220 B F930J227MBA 13.9 30 1.2 15 6.8 A F931D685MAA 1.4 6 3.5 ∗ 220 C F930J227MCC 13.9 14 0.7 ∗ 6.8 B F931D685MBA 1.4 6 2.5 ∗ 220 N F930J227MNC 13.9 10 0.5 ∗ 10 A F931D106MAA 2.0 8 3.5 ∗ 330 N F930J337MNC 20.8 14 0.5 ∗ 20V 10 B F931D106MBA 2.0 6 2.1 ∗ 470 N F930J477MNC 29.6 16 0.3 ∗ 15 C F931D156MCC 3.0 6 1.2 ∗ 6.8 A F931A685MAA 0.7 6 3.5 ∗ 22 B F931D226MBA 4.4 8 1.9 ∗ 10 A F931A106MAA 1.0 6 3.0 ∗ 22 C F931D226MCC 4.4 8 1.1 ∗ 15 A F931A156MAA 1.5 8 2.9 ∗ 33 C F931D336MCC 6.6 8 1.1 ∗ 22 A F931A226MAA 2.2 12 2.5 ∗ 33 N F931D336MNC 6.6 6 0.7 ∗ 22 B F931A226MBA 2.2 6 1.9 ∗ 47 C F931D476MCC 9.4 10 1.1 ∗ 33 A F931A336MAA 3.3 18 2.5 ∗ 47 N F931D476MNC 9.4 8 0.7 ∗ 33 B F931A336MBA 3.3 8 1.4 ∗ 1 A F931E105MAA 0.5 4 7.5 ∗ ± 47 A F931A476MAA 4.7 40 2.0 15 1.5 A F931E155MAA 0.5 4 6.7 ∗ 47 B F931A476MBA 4.7 8 1.0 ∗ 2.2 A F931E225MAA 0.6 6 6.3 ∗ 10V 47 C F931A476MCC 4.7 6 0.9 ∗ 3.3 A F931E335MAA 0.8 6 6.0 ∗ ± 68 B F931A686MBA 6.8 12 0.9 15 4.7 A F931E475MAA 1.2 8 4.0 ∗ 68 C F931A686MCC 6.8 8 0.8 ∗ 4.7 B F931E475MBA 1.2 6 2.8 ∗ ± 100 B F931A107MBA 10.0 18 1.2 15 25V 10 B F931E106MBA 2.5 12 1.9 ∗ 100 C F931A107MCC 10.0 10 0.7 ∗ 10 C F931E106MCC 2.5 6 1.5 ∗ 100 N F931A107MNC 10.0 8 0.6 ∗ 15 C F931E156MCC 3.8 8 1.2 ∗ 150 C F931A157MCC 15.0 14 0.7 ∗ 22 C F931E226MCC 5.5 8 1.1 ∗ 150 N F931A157MNC 15.0 10 0.6 ∗ 22 N F931E226MNC 5.5 6 0.7 ∗ 220 N F931A227MNC 22.0 12 0.5 ∗ 33 N F931E336MNC 8.3 8 0.7 ∗ 330 N F931A337MNC 33.0 18 0.5 ∗ 47 N F931E476MNC 11.8 8 0.7 ∗ 0.68 A F931V684MAA 0.5 4 7.6 ∗ 1 A F931V105MAA 0.5 4 7.5 ∗ 1.5 A F931V155MAA 0.5 6 7.5 ∗ 2.2 A F931V225MAA 0.8 6 7.0 ∗ 2.2 B F931V225MBA 0.8 4 3.8 ∗ 3.3 B F931V335MBA 1.2 4 3.5 ∗ 35 V 4.7 B F931V475MBA 1.6 8 3.1 ∗ 1 : ΔC/C Marked "∗" * 4.7 C F931V475MCC 1.6 6 1.8 ∗ • • • 6.8 C F931V685MCC 2.4 6 1.8 ∗ I t e m A B C N Case (%) Damp Heat ±10 10 C F931V106MCC 3.5 6 1.6 ∗ Tempereature cycles ±5 15 N F931V156MNC 5.3 6 0.7 ∗ Resistance soldering heat ±5 22 N F931V226MNC 7.7 8 0.7 ∗ Surge ±5 Endurance ±10 In case of capacitance tolerance ±10% type, K will be put at 9th digit of type numbering system. CAT.8100A