DATA SHEET
TFT COLOR LCD MODULE
NL6448AC33-18
26 cm (10.4 inches), 640 × 480 pixels, 262144 colors,
incorporated two-lamp/edge-light type backlight
DESCRIPTION
NL6448AC33-18 is a TFT (thin film transistor) active matrix color liquid crystal display (LCD) comprising amorphous
silicon TFT attached to each signal electrode, a driving circuit and a backlight. NL6448AC33-18 has a built-in backlight.
Backlight includes long life CCFLs and the tubes are replaceable.
The 26 cm diagonal display area contains 640 × 480 pixels and can display 262144 colors simultaneously.
NL6448AC33-18 is suitable for factory automation use, because luminance is higher, and viewing direction is
selectable by switching display scan direction.
FEATURES
• Backlight tube replaceable (refer to the tube replace manual for NL6448AC33-18)
2
• High luminance (200 cd/m TYP.)
• Display up side/down side reverse function (user set up)
• Low reflection
• 6-bit digital RGB signals
• 3.3 V operation (5.0 V available)
• Incorporated edge type backlight (Two lamps, with inverter, bright/dark selectable)
• Data enable function (DE/Fixed mode select: user set up)
• Smooth polarizer surface (No antiglare treatment)
APPLICATIONS
• Personal computers (PC) for factory automation
• Display terminals for control system
• Monitors for process controller
The information in this document is subject to change without notice.
Document No. EN0195EJ2V1DS00
Date Published February 1999 P
Printed in Japan
1996
©
NL6448AC33-18
STRUCTURE AND FUNCTIONS
A TFT color LCD module comprises a TFT LCD panel, LSIs for driving liquid crystal, and the backlight. The
TFT LCD panel is composed of a TFT array glass substrate superimposed on a color filter glass substrate with
liquid crystal filled in the narrow gap between two substrates. The backlight apparatus is located on the backside
of the LCD panel.
RGB (Red, Green, Blue) data signals are sent to LCD panel drivers after modulation into suitable forms for
active matrix addressing through signal processor.
Each of the liquid crystal cells acts as an electro-optical switch that controls the light transmission from the
backlight by a signal applied to a signal electrode through the TFT switch.
BLOCK DIAGRAM
H-driver
Digital
1920 lines
R0–R5
Level
G0–G5 signal
shift
B0–B5
processor TFT LCD panel
H : 640 × 3 (R, G, B)
V : 480
CLK
Hsync
LCD timing
Scan select
Vsync
controller
SW1 - SW 4
DE
SW5
DE/Fixed mode select
Power
LSls
VCC supply Backlight
Drivers
circuit
VDDB Inverter
BRTHL
GND (SG)
Frame
GNDB
2
V-driver
480 lines
NL6448AC33-18
OUTLINE OF CHARACTERISTICS (at room temperature)
Display area 211.2 (H) × 158.4 (V) mm
Drive system a-Si TFT active matrix
Display colors 262144 colors
Number of pixels 640 × 480 pixels
Pixel arrangement RGB vertical stripe
Pixel pitch 0.33 (H) × 0.33 (V) mm
Module size 243.0 (H) × 185.1 (V) × 11.0 max. (D) mm
Weight 470 g (typ.) + 15 g (typ., inverter)
Contrast ratio 150:1 (typ.)
Viewing angle (more than the contrast ratio of 10:1)
Horizontal : 45˚ (typ. left side, right side)
Vertical : 30˚ (typ. up side), 20˚ (typ. down side)
Designed viewing direction • Wider viewing angle with contrast ratio
: up side (12 o’clock, normal scan)
: down side (6 o’clock, reverse scan)
• Wider viewing angle without image reversal
: down side (6 o’clock, normal scan)
: up side (12 o’clock, reverse scan)
• Optimum grayscale (γ = 2.2): perpendicular
Color gamut 43 % (typ. center, to NTSC)
Response time 40 ms (max.), “white” to “black”
2
Luminance 200 cd/m (typ., lamp current: 5.0 mA (per one lamp))
Signal system 6-bit digital signals for each of RGB primary colors, synchronous signals
(Hsync, Vsync), dot clock (CLK), DE signal
Supply voltages 3.3 V [5.0 V], 12 V
Backlight Edge light type, two cold cathode fluorescent lamp
Power consumption 6.8 W (typ. at 3.3 V, 12.0 V)
GENERAL SPECIFICATIONS
Item Specification Unit
Module size 243.0 ± 0.5 (H) × 185.1 ± 0.5 (V) × 11.0 max. (D) mm
+0.7
Invertor size 25.0 ± 0.5 (H) × 100 (V) × 10.2 max. (D) mm
–0.3
Display area 211.2 (H) × 158.4 (V) mm
Number of pixels 640 (H) × 480 (V) pixel
Dot pitch 0.11 (H) × 0.33 (V) mm
Pixel pitch 0.33 (H) × 0.33 (V) mm
Pixel arrangement RGB (Red, Green, Blue) vertical stripe
Display colors 262144 color
Weight Module: 480 (max.) + Inverter: 20 (max.) g
3
NL6448AC33-18
ABSOLUTE MAXIMUM RATINGS
Parameter Symbol Rating Unit Remarks
Supply voltage VCC –0.3 to 6.5 V Ta = 25 ˚C
Input voltage VI –0.3 to 6.5 V VI – VCC < 3.0
Storage temp. TST –20 to 60 ˚C
Operating temp. TOP 0 to 50 ˚C Module surface*
Humidity ≤ 95 % relative humidity Ta ≤ 40 ˚C No condensation
≤ 85 % relative humidity 40 < Ta ≤ 50 ˚C
Absolute humidity shall not Ta > 50 ˚C
exceed Ta = 50 ˚C,
85 % relative humidity level
* Measured at the display area
ELECTRICAL CHARACTERISTICS
(1) Logic, LCD driving
Ta = 25 ˚C
Parameter Symbol Min. Typ. Max. Unit Remarks
Supply voltage VCC 3.0 3.3 3.6 V VCC = 3.3 V
(4.75) (5.0) (5.25) (VCC = 5.0 V)
Logic input “L” voltage VIL 0– VCC × 0.3 V
CMOS level
Logic input “H” voltage VIH VCC × 0.7 – VCC V
1 2
Supply current ICC – * 300 * 400 mA VCC = 3.3 V
1 2
– * (200) * (300) mA (VCC = 5.0 V)
*1. Checker flag pattern (in EIAJ ED-2522)
*2. Theoretical maximum current pattern
(2) Backlight
Ta = 25 ˚C
Parameter Symbol Min. Typ. Max. Unit Remarks
Supply voltage VDDB 11.4 12.0 12.6 V –
2
Supply current IDDB – 480 – mA 200cd/m
SUPPLY VOLTAGE SEQUENCE
*1 The supply voltage for input signals should
3.0 (4.75 V) 3.0 (4.75 V)
0s
upper side
CN2
NL6448AC33-18
Inverter
CN1
CN3
lower side
1
2
1
2
3 4
3
·
·
4 ·
·
·
·
5 ·
·
·
·
31 30
Note 1. CN2 is not connected each other at shipment. It should be connected, when LCD is operated.
6
NL6448AC33-18
DISPLAY COLORS vs. INPUT DATA SIGNALS
Data signal (0: Low level, 1: High level)
Display colors
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
Black 000000 000000 000000
Blue 000000 000000 111111
Red 111111 000000 000000
Basic colors Magenta 111111 000000 111111
Green 000000 111111 000000
Cyan 000000 111111 111111
Yellow 111111 111111 000000
White 111111 111111 111111
Black 000000 000000 000000
000001 000000 000000
dark 000010 000000 000000
|| |
↑
Red grayscale | | |
↓ || |
bright 111101 000000 000000
111110 000000 000000
Red 111111 000000 000000
Black 000000 000000 000000
000000 000001 000000
dark 000000 000010 000000
|| |
↑
Green grayscale | | |
↓ || |
bright 000000 111101 000000
000000 111110 000000
Green 000000 111111 000000
Black 000000 000000 000000
000000 000000 000001
dark 000000 000000 000010
|| |
↑
Blue grayscale | | |
↓ || |
bright 000000 000000 111101
000000 000000 111110
Blue 000000 000000 111111
Note Colors are developed in combination with 6 bit signals (64 steps in grayscale) of each primary red, green,
and blue color.
This process can result in up to 262144 (64 × 64 × 64) colors.
7
NL6448AC33-18
INPUT SIGNAL TIMING
(1) Input signal specifications
Parameter Symbol Min. Typ. Max. Unit Remarks
CLK Frequency 1/tC 21.0 25.175 29.0 MHz 39.722 ns (Typ.)
Duty tch/tC 0.4 0.5 0.6 – –
Rise, fall tcrf – – 10 ns –
Hsync Period th 30.0 31.778 33.6 μs 31.469 kHz (Typ.)
– 800 – CLK
Display period thd 640 CLK –
Front-porch thf 16 CLK Fixed timing mode
2 16 – CLK DE mode
Pulse width thp* 10 96 – CLK Fixed timing mode
10 96 – CLK DE mode
Back-porch thb* 4 48 – CLK Fixed timing mode
4 48 – CLK DE mode
thp + thb* 144 CLK Fixed timing mode
14 144 – CLK DE mode
CLK-Hsync timing thch 12 – – ns –
Hsync-CLK timing thcs 8 – – ns –
Hsync-Vsync timing tvh 1 – – CLK 1CLK = 39.722 ns (Typ.)
Vsync-Hsync timing tvs 30 – – ns –
Rise, fall thrf – – 10 ns –
Vsync Period tv 16.1 16.683 17.2 ms 59.94 Hz (Typ.)
– 525 – H
Display period tvd 480 H –
Front-porch tvf 12 H Fixed timing mode
1 12 – H DE mode
Pulse width tvp* 1 2 – H Fixed timing mode
1 2 – H DE mode
Back-porch tvb* 4 31 – H Fixed timing mode
4 31 – H DE mode
tvp + tvb* 33 H Fixed timing mode
5 33 – H DE mode
Rise, fall – – 10 ns –
DATA
CLK-DATA timing tds 8 – – ns –
R0 - R5
DATA-CLK timing tdh 12 – – ns –
G0 - G5
Rise, fall tdrf – – 10 ns –
B0 - B5
DE DE-CLK timing tes 8 – – ns DE mode
CLK-DE timing teh 12 – – ns
Rise, fall terf – – 10 ns
All of parameters should be kept in the specified range.
8
NL6448AC33-18
(2) Definition of input signal timing
tv
tvp
Vsync
tvf
tvb
Note
Display period
tvd
DE
th
thp
Hsync
thf
thb
Display period Note
thd
DE
Note These do not exist as signals.
9
NL6448AC33-18
tC
tch
0.7 VCC
0.5 VCC
CLK
0.3 VCC
tcrf
tds tdh
DATA
INVALID INVALID
(R0 - R5) 0.7 VCC
(G0 - G5) 0.5 VCC
(B0 - B5) 0.3 VCC
tdrf tdrf
teh tes teh tes
0.7 VCC
DE 0.5 VCC
0.3 VCC
terf terf
0.5 VCC
CLK
thch thcs
0.7 VCC
Hsync 0.5 VCC
0.3 VCC
thrf
0.5 VCC
Hsync
tvh tvh
0.7 VCC
Vsync 0.5 VCC
0.3 VCC
tvrf
10
NL6448AC33-18
(3) Input signal timing chart
a) Fixed timing mode
Vsync
1H (min.)
1H (min.)
1H
33H (fixed) 480H (fixed) 12H
Hsync
1 2 3 33
513
34
514
Hsync
34 35 513 514 515
R0 - R5
G0 - G5
B0 - B5
D (X, 0) D (X, Y) D (X, 478) D (X, 479)
INVALID
INVALID (Note: X = 0 to 639)
Hsync
R0 - R5
G0 - G5
B0 - B5
D (0, Y) D (1, Y) D (X, Y) D (638, Y) D (639, Y) INVALID
INVALID
Hsync
10CLK (min.) 4CLK (min.) 1CLK
144CLK (fixed) 640CLK (fixed) 16CLK
CLK
12 144 145 784 785 800 1
R0 - R5
G0 - G5
B0 - B5
INVALID D (0, Y) D (1, Y) D (639, Y) INVALID
(Note: Y = 0 to 479)
11
NL6448AC33-18
b) DE mode
Vsync
1H
tvp tvb 480H (fixed) tvf
Hsync
1
1 2 3
DE
R0 - R5
G0 - G5
B0 - B5
D (X, 0)
D (X, Y) D (X, 479)
INVALID
INVALID
(Note: X = 0 to 639)
DE
R0 - R5
G0 - G5
B0 - B5
INVALID D (0, Y) D (1, Y) D (X, Y) D (638, Y) D (639, Y) INVALID
Hsync
1CLK
thp thb 640CLK (fixed)
thf
CLK
12 144 145 784 785 800 1
DE
R0 - R5
G0 - G5
B0 - B5
INVALID D (639, Y) INVALID
D (0, Y) D (1, Y)
(Note: Y = 0 to 479)
12
NL6448AC33-18
(4) Display position of input data
Normal scan (factory set)
D (0, 0) D (1, 0) - - - D (X, 0) - - - D (638, 0) D (639, 0)
D (0, 1) D (1, 1) - - - D (X, 1) - - - D (638, 1) D (639, 1)
--- ---
D (0, Y) D (1, Y) - - - D (X, Y) - - - D (638, Y) D (639, Y)
--- ---
D (0, 478) D (1, 478) - - - D (X, 478) - - - D (638, 478) D (639, 478)
D (0, 479) D (1, 479) - - - D (X, 479) - - - D (638, 479) D (639, 479)
Reverse scan
D (639, 479) D (638, 479) - - - D (X, 479) - - - D (1, 479) D (0, 479)
D (639, 478) D (638, 478) - - - D (X, 478) - - - D (1, 478) D (0, 478)
--- ---
D (639, Y) D (638, Y) - - - D (X, Y) - - - D (1, Y) D (0, Y)
--- ---
D (639, 1) D (638, 1) - - - D (X, 1) - - - D (1, 1) D (0, 1)
D (639, 0) D (638, 0) - - - D (X, 0) - - - D (1, 0) D (0, 0)
Note 1. The scan direction is set up by switches on the rear side.
Normal scan Reverse scan
SW5 SW1 SW2 SW3 SW4 SW5 SW1 SW2 SW3 SW4
rotary switches dip switch rotary switches dip switch
*SW5 is not related for setting up the scan direction.
Note 2. Below drawings shows relation between the scan direction and viewing direction.
C
N
D (0, 0) D (639, 0)
2
D (0, 0) D (639, 0)
C C
N N
1 1
D (0, 479) D (639, 479)
C
D (0, 479) D (639, 479)
N
2
down side view up side view
13
--- --- --- ---
--- ---
--- ---
--- --- --- ---
--- ---
--- ---
--- --- --- ---
--- --- --- ---
--- --- --- ---
NL6448AC33-18
GENERAL CAUTION
(1) Caution when taking out the module
1) Pick the pouch only, when taking out module from a shipping package.
(2) Cautions for handling the module
1) As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a
protection sheet off from the LCD panel surface as slowly as possible.
2) As the LCD panel and back-light element are made from fragile glass material, impulse and pressure to the
LCD module should be avoided.
3) As the surface of polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning.
4) Do not pull the interface connectors in or out while the LCD module is operating.
5) Put the module display side down on a flat horizontal plane.
6) Handle connectors and cables with care.
7) The torque to mounting screw should never exceed 0.294 N·m (3 Kgf·cm).
(3) Cautions for the operation
1) When the module is operating, do not lose CLK, Hsync or Vsync signals. If any one of these signals is lost,
the LCD panel would be damaged.
2) Obey the supply voltage sequence. If wrong sequence is applied, the module would be damaged.
(4) Cautions for the atmosphere
1) Dew drop atmosphere should be avoided.
2) Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage
in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is
recommended.
3) This module uses cold cathode fluorescent lamps. Therfore, the life time of lamps becomes short
conspicuously at low temperature.
(5) Cautions for the module characteristics
1) Do not apply fixed pattern data signal to the LCD module at product aging. Applying fixed pattern for a long
time may cause image sticking.
(6) Other cautions
1) Do not disassemble and/or re-assemble LCD module. (except for backlight lamp)
2) Do not re-adjust variable resistor or switch etc. (except for scan select switches)
3) When returning the module for repair or etc., please pack the module not to be broken.
We recommend to use the original shipping packages.
4) Turn off the power supply to avoid electrical shock while backlight lamp is replaced, and refer to the backlight
replace manual.
Liquid Crystal Display has the following specific characteristics. These are not defects or malfunctions.
The display condition of LCD module may be affected by the ambient temperature.
The LCD module uses cold cathode tubes for backlighting. Optical characteristics, like luminance or
uniformity, will change during time.
Uneven brightness and/or small spots may be noticed depending on different display patterns.
14
NL6448AC33-18
OUTLINE DRAWING: Front View (Unit in mm)
(62.2)
(13) (82)
+0.7
100–0.3
(161.8) (Bezel opening)
14.6 ±0.3
(158.4) (Display erea)
(12.9)
132.6 ±0.3
(8.1) (4.7) (8.1)
(4.7)
(3.15)
7.5 TYP
10.5 TYP
17 ±0.3
(5.7)
(5.1)
(5.7) (5.1)
166.6 ±0.3
(29.4)
185.1 ±0.5
(16.4) (21.6)
(88.3)
15
243 ±0.5
10.5TYP (4.8)
235 ±0.3
(215.4) (Bezel opening) 10.5 TYP
7.2 ±0.3
5 ±0.3
(211.2) (Display erea) (9.3)
(2.8)
(4)
2.5 ±0.2
(2.9) (3.9)
φ
2- 2.5
(5)
2.5 ±0.2
2-R1.75
5 ±0.3
2.9
(1.8)
Module center
104PWBJ1
Display erea center
5 ±0.3
(3.7)
2.5 ±0.2
4-CPIMS×M2×L4
2- 3.5 φ
(15)
25 ±0.3
LZ-5P-SL-SMT (JAE)
2.5 ±0.2
7.5 TYP
5 ±0.3 (2.9) (3.9)
(2.8) (4)
7.5 TYP
CAUTION
HIGH VOLTAGE
NL6448AC33-18
OUTLINE DRAWING: Rear View (Unit in mm)
(5) (5.3)
83.3 ±0.5
(5.3) (5) (16.4) (21.6)
(0.25)
(54.4)
(48.95)
(43.2)
(37.45)
(31.7)
(4.45)
(8) (6.8) (8)
(6.8)
16
BHR-03VS-1 (JST)
1PIN: COLD.2.3PIN: HOT
(3.4) (4.0)
(5.6) (2.4)
60 ±10
Name 104DLM-17
CAUTION
S
HIGH VOLTAGE
Pal No ∗∗∗−∗
THE TEF COLOR LCD
PANEL CONTAINS COLD CATHODE
FLOURESCENT LAMPS. PLEASE
FOLLOW LOCAL ORDINANCES
OR REGULATIONS FOR ITS
DISPOSAL
2.3 ±0.5
4.0 ± 0.5
DF9-31P-1V
(HIROSE)
104PWBJ1
NL6448AC33-18
ES2228421
MADE IN JAPAN
A100100100100
K2 0 0 0 A 762402
SW4
SW3
(3.4) (3.4) (6.6) (2.4)
SW2
(4.5)
SW1
SW5
NL6448AC33-18
[MEMO]
17
NL6448AC33-18
No part of this document may be copied in any form or by any means without the prior written consent of NEC
Corporation.
NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from use of a device described herein or any other liability arising
from use of such device. No license, either express, implied or otherwise, is granted under any patents,
copyrights or other intellectual property rights of NEC Corporation or of others.
The information in this document is subject to change without notice. Contact your nearest NEC representative
for the latest specifications before designing this device into your system.
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods