6 5 4 3 2 1 1-4 TIME DELAY RELAYS Multi-Time Range/Function TMM Series Power On Response: .05 sec. max. FEATURES Power Off Reset Time: .15 sec. min. ● 100% functionally tested Start Switch Closure Time: .020 sec. to initiate ● Microprocessor controlled timing circuit timing cycle; .050 sec. to reset delay during tim- ● Five logic modes, user selectable ing cycle Power Consumption: 2 VA max. ● Five time ranges, user selectable Frequency: 50/60 Hz ● Easy 3-digit time cycle setting OUTPUT ● ±0.1% repeatability Type: Relay DPDT (2 form C) Time Range Select ● Time cycles from 50 ms to over 16 Rating: 10 A max. resistive at 240 VAC; 100 mA Time Select hours Timing Light at 5 VDC min. load current ● Timing light Life: TIME SELECT ● Superior transient protection Mechanical: 10,000,000 operations 3 4 7 Full Load: 500,000 operations ● Reinforced base locator pin TIMING LIGHT LOGIC ● Flame-retardant polycarbonate housing 9.99S 99.9S 999S Repeat Cycle: Flashing during ON time; Full On 99.9M ● File #E59090 999M during OFF time REPEAT 1-SHOT D.O.B. Other Logic Modes: Flashing during timing; con- INTERVAL D.O.M. The TMM Series offers selectable multiple tinuously on after time out time ranges and functional logic modes all (2729-1) Logic Function PROTECTION in one plug-in package. Transient Voltage: 12, 24, 48 V timers are pro- 3.70 Max Programming is accomplished by using tected by an 8.8 joule metal oxide varistor; 120, 2.90 240 V timers are protected by a 30 joule metal two 5-position rotary switches. One switch .19 Max oxide varistor selects one of five time ranges. The other Dielectric Breakdown: 1500 VAC, RMS min. at switch selects one of five operating logic 60 Hz between input and outputs and between NATIONAL CONTROLS modes. A 3-digit push-button switch selects CORPORATION outputs WEST CHICAGO,IL.60185 the amount of time required for a timing MULTIPLE RANGE SOLID STATE TIMER MECHANICAL MODEL: TMM-0999M-461 cycle. RANGE: .01SEC.-999MIN. Termination: 11-pin plug Mounting: Socket mount, part number SPECIFICATIONS MSO-0011P-012 TIME DELAY ENVIRONMENTAL 1.75 Adjustment: 3 digit push-button switch Storage Temperature: -23°C to 70°C Range: 50 ms to 999 minutes in 5 ranges Operating Temperature: -23°C to 55°C Repeatability: ±0.1%, ±.02 seconds over speci- Humidity: 95% relative fied timing range TIMING ACCURACIES Selectable Time Ranges: .05 to 9.99 seconds; Delay On Make: ±1% of set time, plus fixed error .1 to 99.9 seconds; 1 to 999 seconds; .1 to 99.9 of 80 ms max. (40 ms typical including power-on minutes; 1 to 999 minutes (times less than 50 ms response time) are not recommended due to the response time of the mechanical relay) Interval, One shot: ±1% of set time, plus fixed error of 35 ms max. (10 ms typical) Selectable Operating Logic Modes: Repeat Cycle (50% fixed duty cycle) Delay On Break: ±1% of set time, plus fixed Start Switch Single Shot (1 shot) error of 75 ms max. (10 ms typical) Delay On Break (D.O.B.) 6 7 Repeat Cycle, On Time: ±1% of set time, plus 5 4 8 Interval (Intervl) fixed error of 35 ms max. (10 ms typical) 3 9 Delay On Make (D.O.M.) 2 10 Repeat Cycle, Off Time: ±1% of set time, minus PROGRAMMING 1 11 error of 65 ms max. (10 ms typical) To program the timer, remove voltage from the Input INPUT Voltage unit and select the operating logic mode and the Operating Voltage: 24, 120, 240 VAC; 12, 24, PIN CONFIGURATION time range; use the digital switches to select the Polarity Shown is 48 VDC ±10% (DC models have reverse polarity for D.C. Models required time (0 to 999) protection. Unfiltered input voltage to them must Note: 1) Do not apply voltage or ground to the Start switch, be full-wave rectified) 2) Switch leads should be shielded when running close to other wires (Start switch suppled by customer) ORDERING INFORMATION TIME RANGE 12 VDC 24 VDC 48 VDC 24 VAC 120 VAC 240 VAC .05 sec. to 999 min. TMM-0999M-466 TMM-0999M-462 TMM-0999M-464 TMM-0999M-467 TMM-0999M-461 TMM-0999M-465 AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: 800-323-2593 • 630-231-5900 • FAX: 630-231-1377 • www.nationalcontrols.com 11 10 9 FUNCTION RANGE SELECT SELECT 2.4 8 7