Elite.Parts Manufacturers N NATIONAL SEMICONDUCTOR LM34DZ/NOPB
About product Datasheet FAQ

NATIONAL SEMICONDUCTOR LM34DZ/NOPB

Description

IC SENSOR TEMP PREC FAHR TO-92

Part Number

LM34DZ/NOPB

Price

Request Quote

Manufacturer

NATIONAL SEMICONDUCTOR

Lead Time

Request Quote

Category

PRODUCTS - L

Datasheet

pdf file

9644294_1.pdf

251 KiB

Extracted Text

LM34 Precision Fahrenheit Temperature Sensors November 2000 LM34 Precision Fahrenheit Temperature Sensors hermetic TO-46 transistor packages, while the LM34C, General Description LM34CA and LM34D are also available in the plastic TO-92 The LM34 series are precision integrated-circuit temperature transistor package. The LM34D is also available in an 8-lead sensors, whose output voltage is linearly proportional to the surface mount small outline package. The LM34 is a comple- Fahrenheit temperature. The LM34 thus has an advantage ment to the LM35 (Centigrade) temperature sensor. over linear temperature sensors calibrated in degrees Kelvin, as the user is not required to subtract a large con- Features stant voltage from its output to obtain convenient Fahrenheit n Calibrated directly in degrees Fahrenheit scaling. The LM34 does not require any external calibration 1 ± n Linear +10.0 mV/˚F scale factor or trimming to provide typical accuracies of ⁄2˚F at room 1 temperature and ±1 ⁄2˚F over a full −50 to +300˚F tempera- n 1.0˚F accuracy guaranteed (at +77˚F) ture range. Low cost is assured by trimming and calibration n Rated for full −50˚ to +300˚F range at the wafer level. The LM34’s low output impedance, linear n Suitable for remote applications output, and precise inherent calibration make interfacing to n Low cost due to wafer-level trimming readout or control circuitry especially easy. It can be used n Operates from 5 to 30 volts with single power supplies or with plus and minus supplies. n Less than 90 μA current drain As it draws only 75 μA from its supply, it has very low n Low self-heating, 0.18˚F in still air self-heating, less than 0.2˚F in still air. The LM34 is rated to n Nonlinearity only ±0.5˚F typical operate over a −50˚ to +300˚F temperature range, while the LM34C is rated for a −40˚ to +230˚F range (0˚F with im- n Low-impedance output, 0.4Ω for 1 mA load proved accuracy). The LM34 series is available packaged in Connection Diagrams TO-46 TO-92 Metal Can Package SO-8 Plastic Package (Note 1) Small Outline Molded Package DS006685-1 DS006685-2 Order Numbers LM34H, Order Number LM34CZ, LM34AH, LM34CH, LM34CAZ or LM34DZ DS006685-20 LM34CAH or LM34DH See NS Package N.C. = No Connection See NS Package Number Z03A Number H03H Top View Order Number LM34DM See NS Package Number M08A Note 1: Case is connected to negative pin (GND). © 2000 National Semiconductor Corporation DS006685 www.national.com Typical Applications DS006685-3 FIGURE 1. Basic Fahrenheit Temperature Sensor (+5˚ to +300˚F) DS006685-4 FIGURE 2. Full-Range Fahrenheit Temperature Sensor www.national.com 2 LM34 LM34 Absolute Maximum Ratings (Note 11) TO-46 Package (Soldering, 10 seconds) +300˚C If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ TO-92 Package Distributors for availability and specifications. (Soldering, 10 seconds) +260˚C SO Package (Note 13) Supply Voltage +35V to −0.2V Vapor Phase (60 seconds) 215˚C Output Voltage +6V to −1.0V Infrared (15 seconds) 220˚C Output Current 10 mA Specified Operating Temp. Range (Note 3) Storage Temperature, T to T MIN MAX TO-46 Package −76˚F to +356˚F LM34, LM34A −50˚F to +300˚F TO-92 Package −76˚F to +300˚F LM34C, LM34CA −40˚F to +230˚F SO-8 Package −65˚C to +150˚C LM34D +32˚F to +212˚F ESD Susceptibility (Note 12) 800V Lead Temp. DC Electrical Characteristics (Notes 2, 7) LM34A LM34CA Parameter Conditions Tested Design Tested Design Units Typical Limit Limit Typical Limit Limit (Max) (Note 5) (Note 6) (Note 5) (Note 6) Accuracy (Note 8) T = +77˚F ±0.4 ±1.0 ±0.4 ±1.0 ˚F A T = 0˚F ±0.6 ±0.6 ±2.0 ˚F A T =T ±0.8 ±2.0 ±0.8 ±2.0 ˚F A MAX ± ± ± ± T =T 0.8 2.0 0.8 3.0 ˚F A MIN ± ± ± ± Nonlinearity (Note 9) T ≤ T ≤ T 0.35 0.7 0.30 0.6 ˚F MIN A MAX Sensor Gain T ≤ T ≤ T +10.0 +9.9, +10.0 +9.9, mV/˚F, min MIN A MAX (Average Slope) +10.1 +10.1 mV/˚F, max Load Regulation T = +77˚F ±0.4 ±1.0 ±0.4 ±1.0 mV/mA A (Note 4) T ≤ T ≤ T ±0.5 ±3.0 ±0.5 ±3.0 mV/mA MIN A MAX 0 ≤ I ≤ 1mA L ± ± ± ± Line Regulation T = +77˚F 0.01 0.05 0.01 0.05 mV/V A (Note 4) 5V ≤ V ≤ 30V ±0.02 ±0.1 ±0.02 ±0.1 mV/V S Quiescent Current V = +5V, +77˚F 75 90 75 90 μA S (Note 10) V = +5V 131 160 116 139 μA S V = +30V, +77˚F 76 92 76 92 μA S V = +30V 132 163 117 142 μA S Change of Quiescent 4V ≤ V ≤ 30V, +77˚F +0.5 2.0 0.5 2.0 μA S Current (Note 4) 5V ≤ V ≤ 30V +1.0 3.0 1.0 3.0 μA S Temperature Coefficient +0.30 +0.5 +0.30 +0.5 μA/˚F of Quiescent Current Minimum Temperature In circuit of Figure 1, +3.0 +5.0 +3.0 +5.0 ˚F for Rated Accuracy I =0 L ± ± Long-Term Stability T =T 0.16 0.16 ˚F j MAX for 1000 hours Note 2: Unless otherwise noted, these specifications apply: −50˚F ≤ T ≤ + 300˚F for the LM34 and LM34A; −40˚F ≤ T ≤ +230˚F for the LM34C and LM34CA; and j j +32˚F ≤ T ≤ + 212˚F for the LM34D. V = +5 Vdc and I = 50 μA in the circuit of Figure 2; +6 Vdc for LM34 and LM34A for 230˚F ≤ T ≤ 300˚F. These specifications j S LOAD j also apply from +5˚F to T in the circuit of Figure 1. MAX Note 3: Thermal resistance of the TO-46 package is 720˚F/W junction to ambient and 43˚F/W junction to case. Thermal resistance of the TO-92 package is 324˚F/W junction to ambient. Thermal resistance of the small outline molded package is 400˚F/W junction to ambient. For additional thermal resistance information see table in the Typical Applications section. Note 4: Regulation is measured at constant junction temperature using pulse testing with a low duty cycle. Changes in output due to heating effects can be computed by multiplying the internal dissipation by the thermal resistance. Note 5: Tested limits are guaranteed and 100% tested in production. Note 6: Design limits are guaranteed (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are not used to calculate outgoing quality levels. Note 7: Specification in BOLDFACE TYPE apply over the full rated temperature range. 3 www.national.com DC Electrical Characteristics (Notes 2, 7) (Continued) Note 8: Accuracy is defined as the error between the output voltage and 10 mV/˚F times the device’s case temperature at specified conditions of voltage, current, and temperature (expressed in ˚F). Note 9: Nonlinearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line over the device’s rated temperature range. Note 10: Quiescent current is defined in the circuit of Figure 1. Note 11: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its rated operating conditions (Note 2). Note 12: Human body model, 100 pF discharged through a 1.5 kΩ resistor. Note 13: See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” or the section titled “Surface Mount” found in a current National Semiconductor Linear Data Book for other methods of soldering surface mount devices. DC Electrical Characteristics (Notes 2, 7) LM34 LM34C, LM34D Parameter Conditions Tested Design Tested Design Units Typical Limit Limit Typical Limit Limit (Max) (Note 5) (Note 6) (Note 5) (Note 6) Accuracy, LM34, LM34C T = +77˚F ±0.8 ±2.0 ±0.8 ±2.0 ˚F A ± ± ± (Note 8) T = 0˚F 1.0 1.0 3.0 ˚F A ± ± ± ± T =T 1.6 3.0 1.6 3.0 ˚F A MAX T =T ±1.6 ±3.0 ±1.6 ±4.0 ˚F A MIN Accuracy, LM34D T = +77˚F ±1.2 ±3.0 ˚F A (Note 8) T =T ±1.8 ±4.0 ˚F A MAX T =T ±1.8 ±4.0 ˚F A MIN ± ± ± ± Nonlinearity (Note 9) T ≤ T ≤ T 0.6 1.0 0.4 1.0 ˚F MIN A MAX Sensor Gain T ≤ T ≤ T +10.0 +9.8, +10.0 +9.8, mV/˚F, min MIN A MAX (Average Slope) +10.2 +10.2 mV/˚F, max Load Regulation T = +77˚F ±0.4 ±2.5 ±0.4 ±2.5 mV/mA A (Note 4) T ≤ T ≤ +150˚F ±0.5 ±6.0 ±0.5 ±6.0 mV/mA MIN A 0 ≤ I ≤ 1mA L ± ± ± ± Line Regulation T = +77˚F 0.01 0.1 0.01 0.1 mV/V A ± ± ± ± (Note 4) 5V ≤ V ≤ 30V 0.02 0.2 0.02 0.2 mV/V S Quiescent Current V = +5V, +77˚F 75 100 75 100 μA S (Note 10) V = +5V 131 176 116 154 μA S V = +30V, +77˚F 76 103 76 103 μA S V = +30V 132 181 117 159 μA S Change of Quiescent 4V ≤ V ≤ 30V, +77˚F +0.5 3.0 0.5 3.0 μA S Current (Note 4) 5V ≤ V ≤ 30V +1.0 5.0 1.0 5.0 μA S Temperature Coefficient +0.30 +0.7 +0.30 +0.7 μA/˚F of Quiescent Current Minimum Temperature In circuit of Figure 1, +3.0 +5.0 +3.0 +5.0 ˚F for Rated Accuracy I =0 L ± ± Long-Term Stability T =T 0.16 0.16 ˚F j MAX for 1000 hours www.national.com 4 LM34 LM34 Typical Performance Characteristics Thermal Resistance Thermal Time Constant Thermal Response in Junction to Air Still Air DS006685-23 DS006685-22 DS006685-24 Thermal Response in Minimum Supply Voltage Quiescent Current vs. Stirred Oil Bath vs. Temperature Temperature (In Circuit of Figure 1) DS006685-25 DS006685-26 DS006685-27 Quiescent Current vs. Temp- Accuracy vs. Temperature Accuracy vs. Temperature erature (In Circuit of Figure 2; (Guaranteed) (Guaranteed) −V = −5V, R1 = 100k) S DS006685-29 DS006685-30 DS006685-28 5 www.national.com Typical Performance Characteristics (Continued) Noise Voltage Start-Up Response DS006685-31 DS006685-32 These devices are sometimes soldered to a small, Typical Applications light-weight heat fin to decrease the thermal time constant The LM34 can be applied easily in the same way as other and speed up the response in slowly-moving air. On the integrated-circuit temperature sensors. It can be glued or other hand, a small thermal mass may be added to the cemented to a surface and its temperature will be within sensor to give the steadiest reading despite small deviations about 0.02˚F of the surface temperature. This presumes that in the air temperature. the ambient air temperature is almost the same as the surface temperature; if the air temperature were much Capacitive Loads higher or lower than the surface temperature, the actual temperature of the LM34 die would be at an intermediate Like most micropower circuits, the LM34 has a limited ability temperature between the surface temperature and the air to drive heavy capacitive loads. The LM34 by itself is able to drive 50 pF without special precautions. If heavier loads are temperature. This is expecially true for the TO-92 plastic anticipated, it is easy to isolate or decouple the load with a package, where the copper leads are the principal thermal resistor; see Figure 3. Or you can improve the tolerance of path to carry heat into the device, so its temperature might capacitance with a series R-C damper from output to be closer to the air temperature than to the surface tempera- ture. ground; see Figure 4. When the LM34 is applied with a 499Ω load resistor (as shown), it is relatively immune to wiring To minimize this problem, be sure that the wiring to the capacitance because the capacitance forms a bypass from LM34, as it leaves the device, is held at the same tempera- ground to input, not on the output. However, as with any ture as the surface of interest. The easiest way to do this is linear circuit connected to wires in a hostile environment, its to cover up these wires with a bead of epoxy which will performance can be affected adversely by intense electro- insure that the leads and wires are all at the same tempera- magnetic sources such as relays, radio transmitters, motors ture as the surface, and that the LM34 die’s temperature will with arcing brushes, SCR’s transients, etc., as its wiring can not be affected by the air temperature. act as a receiving antenna and its internal junctions can act The TO-46 metal package can also be soldered to a metal as rectifiers. For best results in such cases, a bypass ca- surface or pipe without damage. Of course in that case, the pacitor from V to ground and a series R-C damper such as IN V terminal of the circuit will be grounded to that metal. − 75Ω in series with 0.2 or 1 μF from output to ground are often Alternatively, the LM34 can be mounted inside a sealed-end useful. These are shown in the following circuits. metal tube, and can then be dipped into a bath or screwed into a threaded hole in a tank. As with any IC, the LM34 and accompanying wiring and circuits must be kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may operate at cold temperatures where conden- sation can occur. Printed-circuit coatings and varnishes such as Humiseal and epoxy paints or dips are often used to insure that moisture cannot corrode the LM34 or its connec- tions. DS006685-6 www.national.com 6 LM34 LM34 Typical Applications DS006685-7 FIGURE 3. LM34 with Decoupling from Capacitive Load DS006685-8 FIGURE 4. LM34 with R-C Damper Temperature Rise of LM34 Due to Self-Heating (Thermal Resistance) Conditions TO-46, TO-46, TO-92, TO-92, SO-8 SO-8 No Heat Small Heat Fin No Heat Small Heat Fin No Heat Small Heat Fin Sink (Note 14) Sink (Note 15) Sink (Note 15) Still air 720˚F/W 180˚F/W 324˚F/W 252˚F/W 400˚F/W 200˚F/W Moving air 180˚F/W 72˚F/W 162˚F/W 126˚F/W 190˚F/W 160˚F/W Still oil 180˚F/W 72˚F/W 162˚F/W 126˚F/W Stirred oil 90˚F/W 54˚F/W 81˚F/W 72˚F/W (Clamped to metal, (43˚F/W) (95˚F/W) infinite heat sink) Note 14: Wakefield type 201 or 1" disc of 0.020" sheet brass, soldered to case, or similar. Note 15: TO-92 and SO-8 packages glued and leads soldered to 1" square of 1/16" printed circuit board with 2 oz copper foil, or similar. Two-Wire Remote Temperature Sensor Two-Wire Remote Temperature Sensor (Grounded Sensor) (Output Referred to Ground) DS006685-9 DS006685-10 V = 10mV/˚F (T +3˚F) OUT A FROM +3˚F TO + 100˚F 7 www.national.com Typical Applications (Continued) 4-to-20 mA Current Source Fahrenheit Thermometer (0 to +100˚F) (Analog Meter) DS006685-12 DS006685-11 Expanded Scale Thermometer Temperature-to-Digital Converter (50˚ to 80˚ Fahrenheit, for Example Shown) (Serial Output, +128˚F Full Scale) DS006685-14 DS006685-13 LM34 with Voltage-to-Frequency Converter and Isolated Output (3˚F to + 300˚F; 30 Hz to 3000 Hz) DS006685-15 www.national.com 8 LM34 LM34 Typical Applications (Continued) Bar-Graph Temperature Display (Dot Mode) DS006685-16 * = 1% or 2% film resistor — Trim R for V = 3.525V B B — Trim R for V = 2.725V C C — Trim R for V = 0.085V + 40 mV/˚F x T A A AMBIENT — Example, V = 3.285V at 80˚F A Temperature-to-Digital Converter ® (Parallel TRI-STATE Outputs for Standard Data Bus to μP Interface, 128 ˚F Full Scale) DS006685-17 9 www.national.com Typical Applications (Continued) Temperature Controller DS006685-18 Block Diagram DS006685-19 www.national.com 10 LM34 LM34 Physical Dimensions inches (millimeters) unless otherwise noted Order Number LM34H, LM34AH, LM34CH, LM34CAH or LM34DH NS Package H03H Order Number LM34DM NS Package Number M08A 11 www.national.com Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Order Number LM34CZ, LM34CAZ or LM34DZ NS Package Z03A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or 2. A critical component is any component of a life systems which, (a) are intended for surgical implant support device or system whose failure to perform into the body, or (b) support or sustain life, and can be reasonably expected to cause the failure of whose failure to perform when properly used in the life support device or system, or to affect its accordance with instructions for use provided in the safety or effectiveness. labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor National Semiconductor National Semiconductor National Semiconductor Corporation Europe Asia Pacific Customer Japan Ltd. Americas Fax: +49 (0) 180-530 85 86 Response Group Tel: 81-3-5639-7560 Tel: 1-800-272-9959 Email: europe.support@nsc.com Tel: 65-2544466 Fax: 81-3-5639-7507 Fax: 1-800-737-7018 Deutsch Tel: +49 (0) 69 9508 6208 Fax: 65-2504466 Email: support@nsc.com English Tel: +44 (0) 870 24 0 2171 Email: ap.support@nsc.com www.national.com Français Tel: +33 (0) 1 41 91 8790 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. LM34 Precision Fahrenheit Temperature Sensors

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the LM34DZ/NOPB have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

product

NATIONAL SEMICONDUCTOR LM10CN/NOPB Amplifier - Operational Amplifier (Op-Amp) IC

product

-LIFETIME BUYS TIL 02/07 RoHS Compliant: Yes

product

60V INPUT 2A 150KHZ S SWITCHER RoHS Compliant: Yes

product

STEP DOWN DC-DC CONVERTER RoHS Compliant: Yes

product

IC SUPER MATCHED NPN PAIRS TO-5

product

IC TRANSISTOR ULTR REL PWR TO220