Elite.Parts Manufacturers N NATIONAL SEMICONDUCTOR LM331N/NOPB
About product Specifications Features Datasheet FAQ

NATIONAL SEMICONDUCTOR LM331N/NOPB

Image of NATIONAL SEMICONDUCTOR LM331N/NOPB

Description

National Semiconductor LM331N/NOPB Converter - Voltage to Frequency; 8; Dual-In-Line; 10 kHz (Min.); 40 V; -0.2 V

Part Number

LM331N/NOPB

Price

Request Quote

Manufacturer

NATIONAL SEMICONDUCTOR

Lead Time

Request Quote

Category

PRODUCTS - L

Specifications

Dual-In-Line Package (Plastic)

260°C

ESD Susceptibility

500V

Input Voltage

-0.2V to +VS

Operating Ambient Temperature

0°C to +70°C

Output Short Circuit to Ground

Continuous

Output Short Circuit to VCC

Continuous

Package Dissipation at 25°C

1.25W

Supply Voltage, VS

40V

Features

Datasheet

pdf file

lm331-Datashee-1500788502t.pdf

839 KiB

Extracted Text

LM231,LM331 LM231A/LM231/LM331A/LM331 Precision Voltage-to-Frequency Converters Literature Number: SNOSBI2A LM231A/LM231/LM331A/LM331 Precision Voltage-to-Frequency Converters April 2006 LM231A/LM231/LM331A/LM331 Precision Voltage-to-Frequency Converters over the full operating temperature range, at power supplies General Description as low as 4.0V. The precision timer circuit has low bias TheLM231/LM331familyofvoltage-to-frequencyconverters currentswithoutdegradingthequickresponsenecessaryfor are ideally suited for use in simple low-cost circuits for 100 kHz voltage-to-frequency conversion. And the output analog-to-digital conversion, precision frequency-to-voltage are capable of driving 3 TTL loads, or a high voltage output conversion, long-term integration, linear frequency modula- up to 40V, yet is short-circuit-proof against V . CC tion or demodulation, and many other functions. The output when used as a voltage-to-frequency converter is a pulse Features train at a frequency precisely proportional to the applied n Guaranteed linearity 0.01% max inputvoltage.Thus,itprovidesalltheinherentadvantagesof the voltage-to-frequency conversion techniques, and is easy n Improved performance in existing voltage-to-frequency to apply in all standard voltage-to-frequency converter appli- conversion applications cations. Further, the LM231A/LM331A attain a new high n Split or single supply operation level of accuracy versus temperature which could only be n Operates on single 5V supply attained with expensive voltage-to-frequency modules. Ad- n Pulse output compatible with all logic forms ditionally the LM231/331 are ideally suited for use in digital n Excellent temperature stability: ±50 ppm/˚C max systems at low power supply voltages and can provide low- n Low power consumption: 15 mW typical at 5V cost analog-to-digital conversion in microprocessor- n Wide dynamic range, 100 dB min at 10 kHz full scale controlled systems. And, the frequency from a battery pow- frequency eredvoltage-to-frequencyconvertercanbeeasilychanneled n Wide range of full scale frequency: 1 Hz to 100 kHz through a simple photo isolator to provide isolation against n Low cost high common mode levels. The LM231/LM331 utilize a new temperature-compensated band-gap reference circuit, to provide excellent accuracy Connection Diagram Dual-In-Line Package 00568021 Order Number LM231AN, LM231N, LM331AN, or LM331N See NS Package Number N08E Ordering Information Device Temperature Range Package LM231N −25˚C ≤ T ≤ +85˚C N08E (DIP) A LM231AN −25˚C ≤ T ≤ +85˚C N08E (DIP) A LM331N 0˚C ≤ T ≤ +70˚C N08E (DIP) A LM331AN 0˚C ≤ T ≤ +70˚C N08E (DIP) A ® Teflon is a registered trademark of DuPont © 2006 National Semiconductor Corporation DS005680 www.national.com Absolute Maximum Ratings Operating Ratings (Note 2) (Notes 1, 2) Operating Ambient Temperature If Military/Aerospace specified devices are required, LM231, LM231A −25˚C to +85˚C pleasecontacttheNationalSemiconductorSalesOffice/ LM331, LM331A 0˚C to +70˚C Distributors for availability and specifications. Supply Voltage, V +4V to +40V S Supply Voltage, V 40V S Output Short Circuit to Ground Continuous Output Short Circuit to V Continuous CC Package Thermal Resistance Input Voltage −0.2V to +V S Package θ Package Dissipation at 25˚C 1.25W (Note 3) J-A 8-Lead Plastic DIP 100˚C/W Lead Temperature (Soldering, 10 sec.) Dual-In-Line Package (Plastic) 260˚C ESD Susceptibility (Note 5) 500V Electrical Characteristics All specifications apply in the circuit of Figure 4, with 4.0V ≤ V ≤ 40V, T =25˚C, unless otherwise specified. S A Parameter Conditions Min Typ Max Units ± ± 4.5V ≤ V ≤ 20V 0.003 0.01 % Full- Scale S VFC Non-Linearity (Note 4) T ≤ T ≤ T ±0.006 ±0.02 % Full- Scale MIN A MAX VFC Non-Linearity in Circuit of Figure 3 V =15V,f=10Hzto11kHz ±0.024 ±0.14 %Full- Scale S Conversion Accuracy Scale Factor (Gain) LM231, LM231A V = −10V, R =14kΩ 0.95 1.00 1.05 kHz/V IN S LM331, LM331A 0.90 1.00 1.10 kHz/V Temperature Stability of Gain LM231/LM331 T ≤ T ≤ T , 4.5V ≤ V ≤ 20V ±30 ±150 ppm/˚C MIN A MAX S LM231A/LM331A ±20 ±50 ppm/˚C 4.5V ≤ V ≤ 10V 0.01 0.1 %/V S Change of Gain with V S 10V ≤ V ≤ 40V 0.006 0.06 %/V S Rated Full-Scale Frequency V = −10V 10.0 kHz IN ± Gain Stability vs. Time (1000 Hours) T ≤ T ≤ T 0.02 % Full- Scale MIN A MAX Over Range (Beyond Full-Scale) V = −11V 10 % IN Frequency INPUT COMPARATOR Offset Voltage ±3 ±10 mV LM231/LM331 T ≤ T ≤ T ±4 ±14 mV MIN A MAX ± ± LM231A/LM331A T ≤ T ≤ T 3 10 mV MIN A MAX Bias Current −80 −300 nA Offset Current ±8 ±100 nA Common-Mode Range T ≤ T ≤ T −0.2 V −2.0 V MIN A MAX CC TIMER Timer Threshold Voltage, Pin 5 0.63 0.667 0.70 x V S Input Bias Current, Pin 5 V = 15V S ± ± All Devices 0V ≤ V ≤ 9.9V 10 100 nA PIN 5 LM231/LM331 V = 10V 200 1000 nA PIN 5 LM231A/LM331A V = 10V 200 500 nA PIN 5 V (Reset) I=5mA 0.22 0.5 V SAT PIN 5 CURRENT SOURCE (Pin 1) Output Current LM231, LM231A R =14kΩ,V = 0 126 135 144 µA S PIN 1 LM331, LM331A 116 136 156 µA Change with Voltage 0V ≤ V ≤ 10V 0.2 1.0 µA PIN 1 Current Source OFF Leakage www.national.com 2 LM231A/LM231/LM331A/LM331 LM231A/LM231/LM331A/LM331 Electrical Characteristics (Continued) All specifications apply in the circuit of Figure 4, with 4.0V ≤ V ≤ 40V, T =25˚C, unless otherwise specified. S A Parameter Conditions Min Typ Max Units CURRENT SOURCE (Pin 1) LM231, LM231A, LM331, LM331A 0.02 10.0 nA All Devices T =T 2.0 50.0 nA A MAX Operating Range of Current (Typical) (10 to 500) µA REFERENCE VOLTAGE (Pin 2) LM231, LM231A 1.76 1.89 2.02 V DC LM331, LM331A 1.70 1.89 2.08 V DC Stability vs. Temperature ±60 ppm/˚C Stability vs. Time, 1000 Hours ±0.1 % LOGIC OUTPUT (Pin 3) I=5mA 0.15 0.50 V V I = 3.2 mA (2 TTL Loads), SAT 0.10 0.40 V T ≤ T ≤ T MIN A MAX OFF Leakage ±0.05 1.0 µA SUPPLY CURRENT V = 5V 2.0 3.0 4.0 mA S LM231, LM231A V = 40V 2.5 4.0 6.0 mA S V = 5V 1.5 3.0 6.0 mA S LM331, LM331A V = 40V 2.0 4.0 8.0 mA S Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC andAC electrical specifications do not apply when operating the device beyond its specified operating conditions. Note 2: All voltages are measured with respect to GND = 0V, unless otherwise noted. Note 3: The absolute maximum junction temperature (T max) for this device is 150˚C. The maximum allowable power dissipation is dictated by T max, the J J junction-to-ambient thermal resistance (θ ), and the ambient temperature T , and can be calculated using the formula P max=(T max - T )/θ . The values for JA A D J A JA maximumpowerdissipationwillbereachedonlywhenthedeviceisoperatedinaseverefaultcondition(e.g.,wheninputoroutputpinsaredrivenbeyondthepower supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided. Note 4: Nonlinearity is defined as the deviation of f from V x (10 kHz/−10 V ) when the circuit has been trimmed for zero error at 10 Hz and at 10 kHz, over OUT IN DC ® the frequency range 1 Hz to 11 kHz. For the timing capacitor, C , use NPO ceramic, Teflon , or polystyrene. T Note 5: Human body model, 100 pF discharged through a 1.5 kΩ resistor. 3 www.national.com Functional Block Diagram 00568002 Pin numbers apply to 8-pin packages only. FIGURE 1. www.national.com 4 LM231A/LM231/LM331A/LM331 LM231A/LM231/LM331A/LM331 Typical Performance Characteristics (All electrical characteristics apply for the circuit of Figure 4, unless otherwise noted.) Nonlinearity Error as Precision V-to-F Converter (Figure 4) Nonlinearity Error 00568025 00568026 Nonlinearity Error vs. Power Supply Voltage Frequency vs. Temperature 00568028 00568027 Output Frequency vs. V vs. Temperature V REF SUPPLY 00568030 00568029 5 www.national.com Typical Performance Characteristics (Continued) 100 kHz Nonlinearity Error Nonlinearity Error (Figure 5) (Figure 3) 00568032 00568031 Input Current (Pins 6,7) vs. Temperature Power Drain vs. V SUPPLY 00568033 00568034 Output Saturation Voltage vs. Nonlinearity Error, Precision I (Pin 3) F-to-V Converter (Figure 7) OUT 00568036 00568035 www.national.com 6 LM231A/LM231/LM331A/LM331 LM231A/LM231/LM331A/LM331 Detail of Operation, Functional Block Applications Information Diagram (Figure 1) The block diagram shows a band gap reference which pro- PRINCIPLES OF OPERATION vides a stable 1.9 V output. This 1.9 V is well regulated DC DC The LM231/331 are monolithic circuits designed for accu- over a V range of 3.9V to 40V. It also has a flat, low S racy and versatile operation when applied as voltage-to- 1 temperature coefficient, and typically changes less than ⁄2% frequency (V-to-F) converters or as frequency-to-voltage (F- over a 100˚C temperature change. to-V) converters. A simplified block diagram of the LM231/ The current pump circuit forces the voltage at pin 2 to be at 331 is shown in Figure 2 and consists of a switched current 1.9V, and causes a current i=1.90V/R to flow. For R =14k, source, input comparator, and 1-shot timer. S s i=135 µA. The precision current reflector provides a current equal to i to the current switch. The current switch switches thecurrenttopin1ortoground,dependinguponthestateof the R flip-flop. S The timing function consists of an R flip-flop and a timer S comparator connected to the external RC network. When t t the input comparator detects a voltage at pin 7 higher than pin 6, it sets the R flip-flop which turns ON the current S switch and the output driver transistor. When the voltage at 2 pin 5 rises to ⁄3 V , the timer comparator causes the R CC S flip-flop to reset. The reset transistor is then turned ON and the current switch is turned OFF. However, if the input comparator still detects pin 7 higher 2 than pin 6 when pin 5 crosses ⁄3 V , the flip-flop will not be CC reset, and the current at pin 1 will continue to flow, trying to make the voltage at pin 6 higher than pin 7. This condition will usually apply under start-up conditions or in the case of an overload voltage at signal input. During this sort of over- 00568004 load the output frequency will be 0.As soon as the signal is restored to the working range, the output frequency will be FIGURE 2. Simplified Block Diagram of Stand-Alone resumed. Voltage-to-Frequency Converter and The output driver transistor acts to saturate pin 3 with an ON External Components resistance of about 50Ω. In case of over voltage, the output current is actively limited to less than 50 mA. The voltage at pin 2 is regulated at 1.90 V for all values of Simplified Voltage-to-Frequency Converter DC i between 10 µA to 500 µA. It can be used as a voltage The operation of these blocks is best understood by going reference for other components, but care must be taken to through the operating cycle of the basic V-to-F converter, ensure that current is not taken from it which could reduce Figure 2, which consists of the simplified block diagram of the accuracy of the converter. the LM231/331 and the various resistors and capacitors connected to it. Basic Voltage-to-Frequency Converter (Figure 3) The voltage comparator compares a positive input voltage, The simple stand-alone V-to-F converter shown in Figure 3 V1, at pin 7 to the voltage, V , at pin 6. If V1 is greater, the x includes all the basic circuitry of Figure 2 plus a few compo- comparator will trigger the 1-shot timer. The output of the nents for improved performance. timer will turn ON both the frequency output transistor and Aresistor, R =100 kΩ ±10%, has been added in the path to the switched current source for a period t=1.1 RC. During IN t t pin 7, so that the bias current at pin 7 (−80 nA typical) will this period, the current i will flow out of the switched current cancel the effect of the bias current at pin 6 and help provide source and provide a fixed amount of charge,Q=ixt, into minimum frequency offset. the capacitor, C .This will normally charge V up to a higher L x levelthanV1.Attheendofthetimingperiod,thecurrentiwill The resistance R at pin 2 is made up of a 12 kΩ fixed S turn OFF, and the timer will reset itself. resistorplusa5kΩ(cermet,preferably)gainadjustrheostat. The function of this adjustment is to trim out the gain toler- Now there is no current flowing from pin 1, and the capacitor ance of the LM231/331, and the tolerance of R,R and C. C willbegraduallydischargedbyR untilV fallstothelevel t L t L L x of V1. Then the comparator will trigger the timer and start For best results, all the components should be stable low- another cycle. temperature-coefficient components, such as metal-film re- sistors. The capacitor should have low dielectric absorption; The current flowing into C is exactly I = i x (1.1xRC)xf, L AVE t t depending on the temperature characteristics desired, NPO and the current flowing out of C is exactly V /R . V /R . L x L IN L ceramic, polystyrene, Teflon or polypropylene are best If V is doubled, the frequency will double to maintain this IN suited. balance. Even a simple V-to-F converter can provide a fre- quency precisely proportional to its input voltage over a wide AcapacitorC isaddedfrompin7togroundtoactasafilter IN range of frequencies. for V .Avalue of 0.01 µF to 0.1 µF will be adequate in most IN cases; however, in cases where better filtering is required, a 1µFcapacitorcanbeused.WhentheRCtimeconstantsare matched at pin 6 and pin 7, a voltage step at V will cause IN a step change in f .IfC is much less than C , a step at OUT IN L V may cause f to stop momentarily. IN OUT 7 www.national.com Applications Information (Continued) Details of Operation: Precision V-To-F Converter A47Ω resistor, in series with the 1 µF C , provides hyster- (Figure 4) L esis, which helps the input comparator provide the excellent In this circuit, integration is performed by using a conven- linearity. tional operational amplifier and feedback capacitor, C . F When the integrator’s output crosses the nominal threshold level at pin 6 of the LM231/331, the timing cycle is initiated. The average current fed into the op-amp’s summing point (pin 2) is i x (1.1 RC) x f which is perfectly balanced with t t −V /R . In this circuit, the voltage offset of the LM231/331 IN IN inputcomparatordoesnotaffecttheoffsetoraccuracyofthe V-to-F converter as it does in the stand-alone V-to-F con- verter; nor does the LM231/331 bias current or offset cur- rent. Instead, the offset voltage and offset current of the operational amplifier are the only limits on how small the signal can be accurately converted. Since op-amps with voltageoffsetwellbelow1mVandoffsetcurrentswellbelow 2nAareavailableatlowcost,thiscircuitisrecommendedfor best accuracy for small signals. This circuit also responds immediately to any change of input signal (which a stand- alonecircuitdoesnot)sothattheoutputfrequencywillbean 00568001 accuraterepresentationofV ,asquicklyas2outputpulses’ IN spacing can be measured. In the precision mode, excellent linearity is obtained be- causethecurrentsource(pin1)isalwaysatgroundpotential and that voltage does not vary with V or f . (In the IN OUT *Use stable components with low temperature coefficients. See Typical stand-alone V-to-F converter, a major cause of non-linearity Applications section. istheoutputimpedanceatpin1whichcausesitochangeas **0.1µF or 1µF, See “Principles of Operation.” a function of V ). IN ThecircuitofFigure5operatesinthesamewayasFigure4, FIGURE 3. Simple Stand-Alone V-to-F Converter but with the necessary changes for high speed operation. ± with 0.03% Typical Linearity (f = 10 Hz to 11 kHz) 00568005 *Use stable components with low temperature coefficients. See Typical Applications section. **This resistor can be 5 kΩ or 10 kΩ for V =8V to 22V, but must be 10 kΩ for V =4.5V to 8V. S S ***Use low offset voltage and low offset current op-amps for A1: recommended type LF411A FIGURE 4. Standard Test Circuit and Applications Circuit, Precision Voltage-to-Frequency Converter www.national.com 8 LM231A/LM231/LM331A/LM331 LM231A/LM231/LM331A/LM331 In the precision circuit, an operational amplifier provides a Applications Information (Continued) bufferedoutputandalsoactsasa2-polefilter.Theripplewill DETAILS OF OPERATION: F-to-V CONVERTERS be less than 5 mV peak for all frequencies above 1 kHz, and (Figure 6 and Figure 7) the response time will be much quicker than in Figure 6. However, for input frequencies below 200 Hz, this circuit will In these applications, a pulse input at f is differentiated by IN have worse ripple thanFigure6.The engineering of the filter a C-R network and the negative-going edge at pin 6 causes time-constants to get adequate response and small enough the input comparator to trigger the timer circuit. Just as with ripple simply requires a study of the compromises to be aV-to-Fconverter,theaveragecurrentflowingoutofpin1is made. Inherently, V-to-F converter response can be fast, but I = i x (1.1 RC)xf. AVERAGE t t F-to-V response can not. In the simple circuit of Figure 6, this current is filtered in the networkR =100kΩand1µF.Theripplewillbelessthan10 L mV peak, but the response will be slow, with a 0.1 second time constant, and settling of 0.7 second to 0.1% accuracy. 00568006 *Use stable components with low temperature coefficients. See Typical Applications section. **This resistor can be 5 kΩ or 10 kΩ for V =8V to 22V, but must be 10 kΩ for V =4.5V to 8V. S S ***Use low offset voltage and low offset current op-amps for A1: recommended types LF411A or LF356. FIGURE 5. Precision Voltage-to-Frequency Converter, ± 100 kHz Full-Scale, 0.03% Non-Linearity 9 www.national.com Applications Information (Continued) 00568007 *Use stable components with low temperature coefficients. FIGURE 6. Simple Frequency-to-Voltage Converter, 10 kHz Full-Scale, ±0.06% Non-Linearity 00568008 *Use stable components with low temperature coefficients. FIGURE 7. Precision Frequency-to-Voltage Converter, 10 kHz Full-Scale with 2-Pole Filter, ±0.01% Non-Linearity Maximum www.national.com 10 LM231A/LM231/LM331A/LM331 LM231A/LM231/LM331A/LM331 Applications Information (Continued) Light Intensity to Frequency Converter 00568009 *L14F-1, L14G-1 or L14H-1, photo transistor (General Electric Co.) or similar Temperature to Frequency Converter 00568010 Long-Term Digital Integrator Using VFC Basic Analog-to-Digital Converter Using Voltage-to-Frequency Converter 00568011 00568012 Analog-to-Digital Converter with Microprocessor 00568013 11 www.national.com Applications Information (Continued) Remote Voltage-to-Frequency Converter with 2-Wire Transmitter and Receiver 00568014 Voltage-to-Frequency Converter with Square-Wave Output Using ÷ 2 Flip-Flop 00568015 Voltage-to-Frequency Converter with Isolators 00568016 www.national.com 12 LM231A/LM231/LM331A/LM331 LM231A/LM231/LM331A/LM331 Applications Information (Continued) Voltage-to-Frequency Converter with Isolators 00568017 Voltage-to-Frequency Converter with Isolators 00568018 Voltage-to-Frequency Converter with Isolators 00568019 13 www.national.com www.national.com 14 LM231A/LM231/LM331A/LM331 Schematic Diagram 00568022 LM231A/LM231/LM331A/LM331 Precision Voltage-to-Frequency Converters PhysicalDimensions inches (millimeters) unless otherwise noted Dual-In-Line Package (N) Order Number LM231AN, LM231N, LM331AN, or LM331N NS Package N08E National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems 2. A critical component is any component of a life support which, (a) are intended for surgical implant into the body, or device or system whose failure to perform can be reasonably (b) support or sustain life, and whose failure to perform when expected to cause the failure of the life support device or properly used in accordance with instructions for use system, or to affect its safety or effectiveness. provided in the labeling, can be reasonably expected to result in a significant injury to the user. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor National Semiconductor National Semiconductor National Semiconductor Americas Customer Europe Customer Support Center Asia Pacific Customer Japan Customer Support Center Support Center Fax: +49 (0) 180-530 85 86 Support Center Fax: 81-3-5639-7507 Email: new.feedback@nsc.com Email: europe.support@nsc.com Email: ap.support@nsc.com Email: jpn.feedback@nsc.com Tel: 1-800-272-9959 Deutsch Tel: +49 (0) 69 9508 6208 Tel: 81-3-5639-7560 English Tel: +44 (0) 870 24 0 2171 www.national.com Français Tel: +33 (0) 1 41 91 8790 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or"enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright© 2011, Texas Instruments Incorporated

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the LM331N/NOPB have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

product

NATIONAL SEMICONDUCTOR LM10CN/NOPB Amplifier - Operational Amplifier (Op-Amp) IC

product

-LIFETIME BUYS TIL 02/07 RoHS Compliant: Yes

product

60V INPUT 2A 150KHZ S SWITCHER RoHS Compliant: Yes

product

STEP DOWN DC-DC CONVERTER RoHS Compliant: Yes

product

IC SUPER MATCHED NPN PAIRS TO-5

product

IC TRANSISTOR ULTR REL PWR TO220