Manufacturers
NAMCO CONTROLS EA740
Description
Namco Controls EA740 Series Nuclear Qualified Limit Switches for Nuclear Environments
Part Number
EA740
Price
Request Quote
Manufacturer
NAMCO CONTROLS
Lead Time
Request Quote
Category
PRODUCTS - E
Datasheet
Namco-Controls-EA740-Series-Nuclear-Qualified-Limit-Switches-datasheet1-737367428.pdf
69 KiB
Extracted Text
Inside Containment Areas EA740 Series Nuclear Qualified Products Limit Switches/ Receptacle Assembly... For Nuclear Environments Features: Technical Data: • Qualified to IEEE Standards 344-1975, 323-1974, andTwo normally open and two normally closed, NEMA 382-1972. form Z contact arrangement. Manufactured to a quality assurance program designedEnclosure meets NEMA 1, 4 and 13 requirements for to meet the requirements of 10CFR50, Appendix B, and dust-tight, water-tight and oil-tight applications. ANSI N45.2, as applicable.Operating lever is adjustable in 7°30' increments Die-cast bronze housing. through 360°. Stainless steel top cover and fasteners.Adequate wiring space for nine conductors. Gold-plated contacts.Rated at 21°C to 90°C. High temperature components throughout.Short term exposure to 175°C. High temperature lubricants.EA 740 has 18° pre-travel, maximum travel 90°. Pressure and radiation resistantWeight EA 740: 4.3 lbs.; EA 740 with Receptacle: 5.3 Seismic and vibration resistant. lbs. Resists chemical spray.DBE maximum test parameters — temperature 340°F, Three mounting styles. pressure 70 PSIG, radiation 204 megarads gamma. EA 740 has a cam action latching mechanism. Receptacle Data Qualified receptacle sealed in place. Qualified ring tongue terminal applied to leads. Continuous Current Rating Every assembly tested before shipment. 75-100% Power Factor* Qualified lead wires. Receptacle keyed for proper alignment of connector. 125 VAC 20 AMPS* All circuits wired. 250 VAC 15 AMPS* Circuits of receptacle identified the same as limit switch 480 VAC 10 AMPS* A, B, C, D, etc. 600 VAC 5 AMPS* 125 VDC 5 AMPS 250 VDC 1.5 AMPS EA740 Series Nuclear Qualified Products FOR INSIDE CONTAINMENT AREAS SWITCHES SHOULD BE SPECIFIED AS FOLLOWS: EA740 Series EA740 Series with Receptacle Se tandard Wg id Lon Se tandardWg id Lon Sn eries Operatio Sn eries Operatio EA740- EA740- C0 W 20 000 50 000 8000 C0 W20 00450 004 8004 EA740 EA740 C1 CW 21 000 51 000 8000 C1 CW21 00451 004 8004 Standard Standard CW & CCW CW & CCW 20 0100 50 010 8010 20 014050 014 8014 (B2 cam) (B2 cam) Maint. Maint. "M" 20 6000 50 600 8600 "M"20 604050 604 8604 Cam Cam EA740 EA740 Maint. Maint. Maint. Maint. "M7" 20 6700 50 670 8670 "M7"20 674050 674 8674 Cam Cam Male Receptacle Assemblies may be ordered separately. Please order part number EC290-19001. Dimensions ����� )�&(�#��&’�&( ���������������� ������ ��������������� ����� ����� ������ ������ ����� ������ ����� ����� ������ ������ ����� ����� ����� ����� ������ ������ ����� ������� �!� ������ ��������" ����� ����� ���������� ������� ������� %�!� #��&’�&( ����� ������� ����� ����� ������� ������� ������ ����� ����� *�+� ����� ����� ����� ������ ����� ������ ����� ������#�$� ������ ������ ����� ����� ������ ����� ����� ������ Nuclear Qualified Products EA740 Series Operational Data Standard Contacts For CW Switch For CCW Switch For CW & CCW Switch C C A A CW Initial CCW CW Initial CCW CW Initial CCW B D D H G H G H G B F E F E F E D C D C D C B A B A B A A. Trip Travel ................................................... 18° B. Reset Travel ............................................... 14° C. Recommended Travel ................................ 30° D. Total Travel Available ................................. 90° Torque to Trip (inch Lbs.) ........................... 27 2 N.O. — 2 N.C. Maintained Contacts & Lever Position Initial Initial Position Position For CW Switch For CCW Switch F D F Initial CCW Initial CCW A C CW CW A D C B B H G H G E E F E F E D C D C B A B A CCW Operating CW Operating CCW CW A. Trip Travel ................................................... 25° 55° B. Reset Travel ............................................... 25° 22° C. Min. Travel to Maintain .............................. 54° 55° D. Recommended Travel ................................ 60° 60° E. Total Travel ................................................. 124° 116° F. Overall Travel ............................................. 56° 64° G. Torque to Trip (inch Lbs.) ........................... 12 6 To change switch orientation from cam (left view) position to cam (right view) position, operate switch thru angle C. Remove lever and reset at initial position. Maintained Contacts — Lever Returned Initial Initial Position Position For CW Switch For CCW Switch C C D D CW Initial CCW CW Initial CCW B B A A H G H G E E E E F E F E D C D C B A B A CCW Operating CW Operating CCW CW A. Trip Travel ................................................... 16° 30° B. Reset Travel ............................................... 30° 26° C. Min. Travel to Maintain .............................. 26° 30° D. Recommended Travel ................................ 45° 45° E. Total Travel ................................................. 90° 90° F. Torque to Trip (inch Lbs.) ........................... 16.5 15 To change switch orientation from cam (left view) position to cam (right view) position, operate switch thru angle B. Remove lever and reset at initial position. EA740 Series Nuclear Qualified Products Accessories PLUG-IN CABLES: Cable lengths for the above Switch/ Receptacle Assemblies should be ordered with specific cable lengths as follows . . . Plug-In Cables Length EC290- 20 Ft. 29020 25 Ft. 29025 30 Ft. 29030 35 Ft. 29035 50 Ft. 29050 100 Ft. 29100 LEVERS: For use inside contain- ment area, levers with bronze arms and beryllium copper rollers are recommended. Note: Levers must be ordered as separate item. For information re- quest Lever Bulletin EL. ADAPTORS: Straight and elbow adapters are available for direct mounting into limit switches. See CD/ EH700 Series Bulletin. 2013 West Meeting Street Lancaster, SC 29720 Technical Assistance: 1-800-NAMTECH © 2002 Namco Controls www.namcocontrols.com EADS04-G | 12/2002
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the EA740 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods