Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. Pyroelectric Infrared Sensors Murata Manufacturing Co., Ltd. Cat.No.S21E-4 Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. ® CONTENTS HIC in this catalog are the trademarks of Murata Manufacturing Co., Ltd. Part Numbering 1 2 1 Dual Type Pyroelectric Infrared Sensor IRA-E700 Series 2 3 Quad Type Pyroelectric Infrared Sensor IRA-E900 Series 4 3 Quad Type Pyroelectric Infrared Sensor IRA-E940ST1 Series 4 Temperature Compensation Single Type Pyroelectric Infrared Sensor 5 IRA-E420 Series Pyroelectric Infrared Sensor IRA Series Characteristics Data 7 Fresnel Lens 10 Notice 13 Recycled Paper Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. o Part Numbering Pyroelectric Infrared Sensor (Part Number) IR A- E710ST 1 q w e r qProduct ID wType eCharacteristics rIndividual Specification Code * Part Number shows only an example which might be different from actual part number. * "eCharacteristics" and "rIndividual Specification Code" might have different digit number from actual Part Number. 1 5.0 0.05 Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. 1 Pyroelectric Infrared Sensors Dual Type Pyroelectric Infrared Sensor Series IRA-E700 Pyroelectric infrared sensors, IRA series, exhibit high sensitivity and reliable performance made possible by Murata's ceramic technology and Hybrid IC technique expertise developed over many years. IRA-E700 series realizes cost benefits and higher performance with a new infrared sensor element of improved material parameters and fabrication. IRA-E700 series is available in two types. IRA-E710ST0 has enhanced immunity to RFI (Radio Frequency Interference). ! Features 1. High sensitivity and excellent S/N ratio ! Dimensions & Circuit Diagrams 2. High stability to temperature changes 3. Slight movement can be detectable. 4.7–0.1 4. High immunity to external noise (Vibration, RFI etc.) 45° 5. Custom design is available. – 6. Higher in cost-performance 45° ! Applications 1. Security 2. Lighting appliances 3. Household or other appliances– f0.45 –0.05 *Specified on the bottom of stem !Rating (25˚C)– * Part Number IRA-E700ST0 IRA-E710ST0 Responsivity (500K, 1Hz, 1Hz) 4.3mVp-p (Typ.) d s q=q=45° Field of View 1 2 g General Tolerance : ±0.2 (in mm) 5μm long-pass Optical Filter Electrode (2.0Z1.0mm)Z2 Supply Voltage 2 to 15V Pyroelectric element Operating Temperature -40 to 70D -40 to 85D Storage Temperature 1.0 1.0 1.0 (in mm) d IRA-E700ST0 s RG g IRA-E710ST0 d s RG g 2 3.6 3.7 0.1 11.0 2 4.7 9.2 2.0 Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. Pyroelectric Infrared Sensors Quad Type Pyroelectric Infrared Sensor Series IRA-E900 2 Pyroelectric infrared sensors, IRA series, exhibit high sensitivity and reliable performance made possible by Murata's ceramic technology and Hybrid IC technique expertise developed over many years. IRA-E900 series realizes cost benefits and higher performance with a new infrared sensor element of improved material parameters and fabrication. IRA-E900 series is available in two types. IRA-E910ST1 has enhanced immunity to RFI (Radio Frequency Interference). ! Features 1. High sensitivity and excellent S/N ratio ! Dimensions & Circuit Diagrams 2. High stability to temperature changes 3. Slight movement can be detectable. 4.7–0.1 41° 4. Non directional sensing with wide F.O.V. 5. High immunity to external noise (Vibration, RFI etc.) 6. Custom design is available. 7. Higher in cost-performance 41° ! Applications 1. Security – 2. Lighting appliancesf0.45 –0.05 3. Household or other appliances*Specified on the bottom of stem * 5.08–0.05 ! Rating (25˚C) d s Part Number IRA-E900ST1 IRA-E910ST1 General Tolerance : ±0.2 g 3.3mV (Typ.) Responsivity (500K, 1Hz, 1Hz) p-p (in mm) q=q=41° Field of View 1 2 Optical Filter 5μm long-pass Pyroelectric element Electrode (1.1Z1.1mm)Z4 Supply Voltage 3 to 15V -25 to 55D Operating Temperature Storage Temperature -40 to 85D (in mm) 1.1 1.0 1.1 d IRA-E900ST1 W Y s Y W Y W W Y RG W Y Y W Y W W Y g IRA-E910ST1 d W Y s Y W Y W W Y RG W Y Y W Y W W Y g 3 9.2 3.6 4.7 11.0 2 1.1 1.0 1.1 Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. Pyroelectric Infrared Sensors Quad Type Pyroelectric Infrared Sensor Series IRA-E940ST1 Pyroelectric infrared sensors, IRA series, exhibit high sensitivity and reliable performance made possible by Murata's ceramic technology and Hybrid IC technique 3 expertise developed over many years. IRA-E940ST1 realizes cost benefits and higher performance with a new infrared sensor element of improved material parameters and fabrication. IRA-E940ST1 which has quad elements and 2 outputs will detect the human body more correctly with OR/AND logic circuit. ! Features 1. High sensitivity and excellent S/N ratio ! Dimensions & Circuit Diagrams 2. High stability to temperature changes 3. High immunity to external noise (Vibration, RFI etc.) 4.7–0.1 50° 4. Higher in cost-performance 5. Custom design is available. ! Applications 55° 1. Security 2. Lighting appliances 3. Household or other appliances – f0.45 –0.05 *Specified on the bottom of stem ! Rating (25˚C) * 5.08–0.05 Part Number IRA-E940ST1 Responsivity (500K, 1Hz, 1Hz) 3.3mV (Typ.) p-p s1 d Field of Viewq1=55°, q2=50° g s2 General Tolerance : ±0.2 5μm long-pass (in mm) Optical Filter (1.35Z1.0mm)Z4 Electrode Supply Voltage 2 to 15V Pyroelectric element Operating Temperature -25 to 55D (Y) W Y (W) Storage Temperature -40 to 85D (Y) W Y (W) (in mm) 1.0 0.8 1.0 d s1 RG g RG s2 4 9.2 3.6 11.0 2 4.7 1.35 0.3 1.35 Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. Pyroelectric Infrared Sensors Temperature Compensation Single Type Pyroelectric Infrared Sensor Series IRA-E420 Single type pyroelectric infrared sensors IRA-E420 series have a temperature compensation element. They are suitable for flame detection and gas detection. ! Features 1. High stability against abrupt ambient temperature changes 2. High immunity to external noise (Vibration, RFI etc.) 3. Custom design is available with varying optical filter. 4 ! Applications Part Number Optical Filter Applications IRA-E420S1 Silicon 1-15μm infrared detection IRA-E420QW1 4.3μm band-pass Flame detection IRA-E420SW1 4.45μm band-pass Flame detection ! Dimensions & Circuit Diagrams (IRA-E420S1, IRA-E420QW1) (IRA-E420SW1) 3.0–0.1 2.4–0.1 17° 17° 50° – ø0.45 ø0.45–0.05 – –0.05 **5.08–0.05 5.08–0.05 *Specified on the bottom of stem*Specified on the bottom of stem d s s d General Tolerance : ±0.2 General Tolerance : ±0.2 g g (in mm) (in mm) Pyroelectric element Pyroelectric element 1.6 1.8 (in mm) (in mm) d s RG g 5 3.6 9.2 11.0 2 4.9 1.5 max. 3.6 9.2 11 2 4.5 Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. ! Rating (25˚C) Part Number IRA-E420S1 IRA-E420QW1 IRA-E420SW1 * 3.4mV (Typ.) 1.3mV (Typ.) Responsivity (500K, 1Hz, 1Hz) p-p p-p 0.45mVp-p (Typ.) q=q=50° Field of Viewq=q=17° 1 2 1 2 Silicon 4.3μm band-pass 4.45μm band-pass Optical Filter Electrode ø1.6mm ø1.8mm Supply Voltage 3 to 15V -25 to 70D -25 to 55D Operating Temperature -25 to 70D -30 to 100D Storage Temperature * 700K, 5Hz, 1Hz 4 6 Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. Pyroelectric Infrared Sensor IRA Series Characteristics Data ! Spectral Response of Window Materials Wave length (μm) 2.5 3.0 4.0 5.0 6.0 7.0 8.0 10.0 12.0 100 5μm Long-Pass Filter 80 4.3μm Band-Pass Filter 60 40 Silicon Filter 20 7μm Long-Pass Filter 4 0 4000 3500 3000 2500 2000 1800 1600 1400 1200 1000 800 -1 Wave number (cm ) ! Frequency Characteristics 10 1 1.0 10 Chopping Frequency (Hz) 7 Relative Responsivity (RV) Transmittance (%) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. Pyroelectric Infrared Sensor IRA Series Characteristics Data ! Test Method of Sensitivity Lock-in Amplifier (1Hz) 140mm W5V d Black Body 47kW s 1 500K* W 22mF g Mechanical Chopper Infrared Sensor 1 1Hz* Oscilloscope Black Body Mechanical Chopper *1 IRA-E420QW1 700K 5Hz IRA-E420SW1 400K 2.5Hz IRA-E700/E900 Series 500K 1Hz 4 ! Typical Application Circuit (Human Detection) 3 Terminal Regulater 78L05 9Y15 100k 100k 4 8 260k 330k B102K B222K LM358 2 2SD596 100k 3.3mD 1S184 120k B102K 220k Photo Coupler 16V 3 S 100k W W 10M 100m100mNJM R WmPD5555G 16V 16V g 10M 2903M 6 120k Relay 100k 100k LM358 B222K W4.7m330k 1k 7 1 1S184 B102K 16V W 10mW B102K W 1 5 C 220k 16V 10mB103K 16V GND TH=1.1ZC (�F) Z R (M‰) second 8 Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. Pyroelectric Infrared Sensor IRA Series Characteristics Data ! Reliability Test IRA-E700 series, IRA-E900 series Item Test Conditions Criteria High Temperature 100D for 500 hrs. After test completion, leave for three hours in Y40D for 500 hrs. Low Temperature normal humidity temperature conditions, and 60D, 95% RH for 500 hrs. Humidity then measure. 20 times of following cycle. 1. External appearance: Heat Cycle Y25D, 30 min.eRoom temp., 30 min.h No significant damage gRoom temp., 30 min.f55D, 30 min. 2. Sensitivity: Apply vibration of amplitude of 1.5mm with 10 to 55Hz band to each of 3 Vibration Tolerance within 20% deviation from original perpendicular directions for 60 min. value Apply shock of 100G sinewave by standard shock tester to each of 3 3. Noise: Shock perpendicular directions. Maximum tolerance W100mV of original value Immerse up to 3.0mm from can case in solder bath of 260T5D for 10T1 s. Soldering Heat Conform to MIL-STD-202F chapter 112D, condition D. Hermetic Sealing No generation of bubbles Immerse in fluorocarbon bath (FC-40) of 125T5D for 20 s. 4 IRA-E420 series Item Test Conditions Criteria High Temperature 100D for 500 hrs. After test completion, leave for three hours in Low Temperature Y30D for 500 hrs. normal humidity temperature conditions, and 60D, 95% RH for 500 hrs. Humidity then measure. 20 times of following cycle. 1. External appearance: Heat Cycle Y25D, 30 min.eRoom temp., 30 min.h No significant damage gRoom temp., 30 min.f55D, 30 min. 2. Sensitivity: Apply vibration of amplitude of 1.5mm with 10 to 55Hz band to each of 3 Vibration Tolerance within 20% deviation from original perpendicular directions for 60 min. value Apply shock of 100G sinewave by standard shock tester to each of 3 Shock 3. Noise: perpendicular directions. Maximum tolerance W100mV of original value Immerse up to 3.0mm from can case in solder bath of 260T5˚C for 10T1 s. Soldering Heat Conform to MIL-STD-202F chapter 112D, condition D. Hermetic Sealing No generation of bubbles Immerse in fluorocarbon bath (FC-40) of 125T5D for 20 s. 9 Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. Pyroelectric Infrared Sensors/Fresnel Lens PPGI0601 m 3.0 C m C 4.0 2.0 B D, D' D B B 1.0 3.0 C D E B' C' A 16.0 A 22.5° Vertical Area 2.0 Horizontal Area 0 A 30° E' D' 1.0 1.0 B' E, E' D' B' 0 2.0 1.0 2.0 3.0 4.0 5.0 m C' Cross-Sectional View C' 3.0 1.0 2.0 3.0 4.0 5.0 m f20.0 4 f21.0 (in mm) PPGI0902 Horizontal Area Vertical Area Sensor 7.7m 9m 2m 10m 1m Sensor 1.6m 10m 3.5m 12° 9m 51.5 56.5 7.7m (in mm) 29.6R Lens plane 0.7max. 10 29.6R 6.4 5.0 3.64 D D' C B A B' C' 3.60 E E' 11.64 R 2.24 8 10 21.5 16.3 44.5 12.1SR Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. Pyroelectric Infrared Sensors/Fresnel Lens PPGI0626 f23T0.2 12.9SR f21.4 f19.4 A B C 3.6 6 3 (in mm) 16.5 4 Detection area on the floor B : 60° pitch Y C : 30° pitch C1 C12 C2 2.2m B1 C11 C3 0.8m B6 B2 C10 C4 Z X B5 B3 C9 B4 C5 C8 C6 C7 A : 0° B : 21.8° C : 48° IML-0635 6m Tab 13º 13º (4.5) ø9.0 ø8.2 5m Step 2m Housing 0m 0m Pyro-Element Figure A 3.0 1.15 1) Insert a sensor into Fresnel lens like each tab is overlapped. (In case there are two tabs on Fresnel lens, the field of view is 2m determined by your choice (TabA or B on Fresnel lens). R4.8 Vertical Please see following page(s) for more details to see which characteristic of field of view is preferable for your application.) 2) Push the sensor into Fresnel lens until the top face of sensor reaches to the stopper inside Fresnel lens. 5.2 5.7 3) Please prepare a housing yourself that is put onto Fresnel lens as shown in FigureA. The hatching area shown in Figure A, 6m must be obscured by the housing in order to prevent mis- Horizontal detection. Unless otherwise unexpected infrared ray comes though the hatching area. *Assembled with Murata sensor IRA-700 series (in mm) General tolerance : –0.2 11 8.65 5.5 5.7 4.5 1.15 4.0 3.4 4.35 (4.35) 9.15 2.5m Pyroelectric element 35º 35º C B A B C 0.5m 10.8m Y Y 2 (m) 3 2 1 0 1 2 3 3 1.8m Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. Pyroelectric Infrared Sensors/Fresnel Lens IML-0636 0.5 Tab 4m 13º 13º 5m (4.5) ø9.0 ø8.2 3m Step Housing ø10.4 0m 0m Focal point (Pyro-Element) Figure A 1) Insert a sensor into Fresnel lens like each tab is overlapped. (In case there are two tabs on Fresnel lens, the field of view is determined by your choice (TabA or B on Fresnel lens). 3m Please see following page(s) for more details to see which Vertical characteristic of field of view is preferable for your application.) 4m 2) Push the sensor into Fresnel lens until the top face of sensor Horizontal reaches to the stopper inside Fresnel lens. 3) Please prepare a housing yourself that is put onto Fresnel lens as *Assembled with Murata sensor IRA-700 series shown in FigureA. The hatching area shown in Figure A, must be obscured by the housing in order to prevent mis-detection. Unless otherwise unexpected infrared ray comes though the hatching area. 4 (in mm) General tolerance : –0.2 IML-0637 0.5 Tab 13º 13º 5m 5m (4.5) ø9.0 ø8.2 2m 2m Step Housing ø10.4 0m 0m Figure A Focal point (Pyro-Element) 1) Insert a sensor into Fresnel lens like each tab is overlapped. (In case there are two tabs on Fresnel lens, the field of view is 2m 2m determined by your choice (TabA or B on Fresnel lens). Please see following page(s) for more details to see which Horizontal Vertical characteristic of field of view is preferable for your application.) 2) Push the sensor into Fresnel lens until the top face of sensor reaches to the stopper inside Fresnel lens. *Assembled with Murata sensor IRA-700 series 3) Please prepare a housing yourself that is put onto Fresnel lens as shown in FigureA. The hatching area shown in Figure A, must be obscured by the housing in order to prevent mis-detection. Unless otherwise unexpected infrared ray comes though the hatching area. (in mm) General tolerance : –0.2 IML-0638 6.11m 3m 3m 42° Tab 13º 13º (4.5) ø9.0 ø8.2 4.91m 0m Step Housing 42° 3m Pyro-Element Figure A 3.0 On the Floor Vertical 1.15 1) Insert a sensor into Fresnel lens like each tab is overlapped. 3m 0m 3m (In case there are two tabs on Fresnel lens, the field of view is determined by your choice (TabA or B on Fresnel lens). R4.8 Please see following page(s) for more details to see which Vertical characteristic of field of view is preferable for your application.) 2) Push the sensor into Fresnel lens until the top face of sensor reaches to the stopper inside Fresnel lens. Horizontal 5.2 5.7 3) Please prepare a housing yourself that is put onto Fresnel lens as shown in FigureA. The hatching area shown in Figure A, must be obscured by the housing in order to prevent mis- detection. Unless otherwise unexpected infrared ray comes 45.5° 45.5° though the hatching area. Pyroelectric Element Horizontal (in mm) Assembled with Murata sensor IRA-700 Series. General tolerance : –0.2 Freshel lens are available upon request. 12 8.65 5.5 5.7 8.65 8.65 4.5 4.5 4.5 0.5 0.5 1.15 4.0 0.5 0.5 3.4 3.4 3.4 4.35 (4.35) (4.35) (4.35) 9.15 9.15 9.15 19.3º 19.3º 6.6m 2.7m 19.3º 19.3º 5.54m 1.8m Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. Notice ! Notice 1. Caution (Design) 2. Caution (Mounting) (1) Please make sure that your product has been evaluated (1) Soldering and confirmed against your specifications when our (a) Hand soldering should be applied. product is mounted to your product. (2) Be sure to provide an appropriate fail-safe function on (b) Soldering should be done quickly as following. your product to prevent a second damage that may be Temperature of soldering iron : 350˚C caused by the abnormal function or the failure of our Distance from can case Period of time product. 1 to 3mm Within 3 seconds per point (3) In case of outdoor use, suitable optical filter and water Over 3mm Within 10 seconds per point and humidity proof structure should be applied. (4) To prevent failure or malfunction, please use a stabilized (c) Soldering flux should be rosin flux and not contain power supply. more than 0.2wt% chlorine. (5) Please avoid using the sensor in the following conditions Soldering flux should be removed after soldering. because it may cause failure or malfunction. (2) Cleaning (a) in such a fluid as water, alcohol etc. corrosive gas Soldering flux should be removed after soldering. (SO , Cl , NO etc.) or sea breeze Soldering flux may cause malfunction or degradation of 2 2 X (b) in high humidity character unless sufficiently cleaned. (c) in a place exposed directly to sunlight or headlights of automobile 3. Caution (Handling and Storage) (d) in a place exposed to rapid ambient temperature (1) The optical filter of the sensor should not be scratched or change soiled. (e) in a place exposed directly to an air-conditioner or (2) Strong shock should be avoided. heat vent (3) Electrostatics and strong electromagnetic field should be (f) strong vibrations avoided. (g) in a place exposed to strong electromagnetic field (4) The sensor should be kept on conductive sponge. (h) in such a place where infrared ray is shaded (5) High temperature, high humidity, fluid such as water or (i) in any other place similar to the above (a) through (h) alcohol etc., corrosive gas (SO , Cl , NO etc.) and sea 2 2 X breeze should be avoided. 13 Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. !Note S21E.pdf 05.11.16 This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. Note: 1. Export Control Murata products should not be used or sold for use in the development, production, stockpiling or utilization of any conventional weapons or mass-destructive weapons (nuclear weapons, chemical or biological weapons, or missiles), or any other weapons. For customers in Japan < > For products which are controlled items subject to the “Foreign Exchange and Foreign Trade Law” of Japan, the export license specified by the law is required for export. 2. Please contact our sales representatives or product engineers before using the products in this catalog for the applications listed below, which require especially high reliability for the prevention of defects which might directly damage to a third party's life, body or property, or when one of our products is intended for use in applications other than those specified in this catalog. q Aircraft equipment w Aerospace equipment e Undersea equipment r Power plant equipment t Medical equipment y Transportation equipment (vehicles, trains, ships, etc.) u Traffic signal equipment i Disaster prevention / crime prevention equipment o Data-processing equipment !0 Application of similar complexity and/or reliability requirements to the applications listed in the above 3. Product specifications in this catalog are as of August 2005. They are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. If there are any questions, please contact our sales representatives or product engineers. 4. Please read rating and CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. 5. This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 6. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect of our and/or a third party's intellectual property rights and other related rights in consideration of your use of our products and/or information described or contained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentioned above under licenses without our consent. 7. No ozone depleting substances (ODS) under the Montreal Protocol are used in our manufacturing process. http://www.murata.com/ Head Office International Division 1-10-1, Higashi Kotari, Nagaokakyo-shi, Kyoto 617-8555, Japan 3-29-12, Shibuya, Shibuya-ku, Tokyo 150-0002, Japan Phone: 81-75-951-9111 Phone: 81-3-5469-6123 Fax: 81-3-5469-6155 E-mail: intl@murata.co.jp