• SmarTRAQ • Product Specification • Application SmarTRAQ Specifications SmarTRAQ SmarTRAQ is a closed-loop technology, limitless, door operator designed to replace older mechanical circuits, cams, and resistors with a digital control sys- tem providing precise door operation and reliable performance. Because SmarTRAQ is limit- less, Door Open Limit and Door Closed Limit signals are generated electronically — DOL and DCL mechanical switches are not required. SmarTRAQ dramatically improves door operation regardless of lobby door mass and wind loading. SmarTRAQ is A17.1, CSA-B44.1 compliant. SmarTRAQ provides flexibility: • Choose to modernize an existing installation economically with a new brushless motor and microprocessor-based inverter drive (re-using existing mechanical equipment) • Replace the complete operator with a new brushless motor, microprocessor-based inverter drive, and new center-parting or side-slide door operator package. 1 SmarTRAQ Specifications Product Specification The SmarTRAQ limitless, closed-loop, door operator includes a permanent-magnet, brushless motor with a built-in encoder and a microprocessor-based inverter drive. The compact inverter drive enclosure mounts easily on the elevator car. The motor replaces the original motor when re-using existing operator packages or mounts to the new operator package when the complete door operator is being replaced or newly installed. Table 1.1 SmarTRAQ Specifications, Interface Data, and Code Compliance Door Operator Drive Technical Data Input Voltage 120VAC, 50/60Hz, Single-phase Output Voltage 3-Phase, 30VAC, 9A (26A peak) Power Requirement 300VA Controller Type Closed Loop, Distance and Velocity Feedback, Limitless Door Motor Technical Data Type Three-phase, synchronous, brushless motor with perma- nent magnet excitation and built-in digital encoder Motor 0.564 HP, 3-Phase AC, 8-Pole, 30 Volt, 9A (26A peak), 0 — 2000 RPM, 0 — 133Hz Encoder 640 PPR (Pulses Per Revolution) Elevator Control Interface Data Input Signals Door Open Door Close Nudging Heavy Door Input Signal Level Dry Contact Output Signals Door Open Limit Door Close Limit Limit 1 Limit 2 Output Signal Level N.O./N.C. Contact, 10 Amp Code Compliance For ASME A17.1-1996 (Rule 210.15), ASME A17.1-2000/CSA B44-00 (Requirement 2.26.5), or CSA B44-94 (Requirement 3.12.1.5) compliance, mechanical Door Position Monitoring Switch must be provided. 2 SmarTRAQ Specification, 42-IS-ST01 Application Application SmarTRAQ offers wide mechanical and electrical interface, providing a cost-effective solution for modernization of existing door operators or for new installations. SmarTRAQ models sup- port: •MCE • Center-Parting Door Operator Package • Two-Speed Center-Parting Door Operator Package • Single-Speed Side Slide Door Operator Package • Two-Speed Side Slide Door Operator Package •Westinghouse • Model A Series • Model B Series • Model BB2 •Model E Series •Model EZ •Model HY •Model MG •Haughton •T •T1 •TH •Montgomery •MAC Series •Dover •DC Series •HD Series • Otis •6970 •7300 • 7782 •GAL • All Models •Armor •C4 3 SmarTRAQ Specifications SmarTRAQ Models To support a wide selection of door operators, SmarTRAQ motor configurations include: Figure 1.1 Motor Configurations Model 4151-F Model 4157-F Otis 7300 Otis 6970 Westinghouse A, B, and BB2 Model 4151-B1 Armor C4 GAL (all models) Haughton T and T1 Otis 7782 Westinghouse E and HY Model 4152-B2 Haughton TH Model 4150-B3 Dover DC and HD Model 4150-B1 MAC Westinghouse EZ 4 SmarTRAQ Specification, 42-IS-ST01