Elite.Parts Manufacturers M MICROCHIP MCP3221DM-PCTL
About product Datasheet FAQ

MICROCHIP MCP3221DM-PCTL

Description

BOARD DEMO FOR PICTAIL MCP3221

Part Number

MCP3221DM-PCTL

Price

Request Quote

Manufacturer

MICROCHIP

Lead Time

Request Quote

Category

PRODUCTS - M

Datasheet

pdf file

4120871_1.pdf

649 KiB

Extracted Text

MCP3221 MCP3221 M 2 Low Power 12-Bit A/D Converter With I C™ Interface Features Description • 12-bit resolution The Microchip Technology Inc. MCP3221 is a succes- sive approximation A/D converter with 12-bit resolu- • ±1 LSB DNL, ±2 LSB INL max. tion. Available in the SOT-23 package, this device • 250 µA max conversion current provides one single-ended input with very low power • 5 nA typical standby current, 1 µA max. consumption. Based on an advanced CMOS technol- 2 • I C™ compatible serial interface ogy, the MCP3221 provides a low maximum conver- 2 C Standard Mode - 100 kHz I sion current and standby current of 250 µA and 1 µA, 2 respectively. Low current consumption, combined with - 400 kHz I C Fast Mode the small SOT-23 package, make this device ideal for • Up to 8 devices on a single 2-Wire bus battery-powered and remote data acquisition 2 C Fast Mode • 22.3 ksps in I applications. • Single-ended analog input channel Communication to the MCP3221 is performed using a • On-chip sample and hold 2 2-wire, I C compatible interface. Standard (100 kHz) • On-chip conversion clock 2 and Fast (400 kHz) I C modes are available with the • Single-supply specified operation: 2.7V to 5.5V device. An on-chip conversion clock enables indepen- 2 • Temperature range: dent timing for the I C and conversion clocks. The device is also addressable, allowing up to eight devices - Industrial: -40°C to +85°C on a single 2-wire bus. - Extended: -40°C to +125°C The MCP3221 runs on a single supply voltage that • Small SOT-23 package operates over a broad range of 2.7V to 5.5V. This device also provides excellent linearity of ±1 LSB differ- Applications ential non-linearity and ±2 LSB integral non-linearity, • Data Logging maximum. • Multi-zone Monitoring Functional Block Diagram • Hand-Held Portable Applications V V DD SS • Battery-Powered Test Equipment • Remote or Isolated Data Acquisition Package Type DAC 5-Pin SOT-23A Comparator – Sample 12-bit SAR SCL 5 AIN and + V 1 DD Hold Clock V 2 SS 2 Control Logic I C™ Interface 4 SDA AIN 3 SCL SDA  2003 Microchip Technology Inc. DS21732B-page 1 MCP3221 1.0 ELECTRICAL PIN FUNCTION TABLE CHARACTERISTICS Name Function Absolute Maximum Ratings † +2.7V to 5.5V Power Supply V DD V Ground V ...................................................................................7.0V SS DD AIN Analog Input Analog input pin w.r.t. V .......... ............. -0.6V to V +0.6V SS DD SDA Serial Data In/Out SDA and SCL pins w.r.t. V ........... .........-0.6V to V +1.0V SS DD Storage temperature .....................................-65°C to +150°C SCL Serial Clock In Ambient temp. with power applied ................-65°C to +125°C Maximum Junction Temperature...................................150°C ESD protection on all pins (HBM) .................................≥ 4kV † Stresses above those listed under “Maximum ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational list- ings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reli- ability. DC ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise noted, all parameters apply at V = 5.0V, V = GND, R = 2 kΩ DD SS PU 2 T = -40°C to +85°C, I C Fast Mode Timing: f = 400 kHz (Note 3). AMB SCL Parameters Sym Min Typ Max Units Conditions DC Accuracy Resolution 12 bits Integral Nonlinearity INL — ±0.75 ±2 LSB Differential Nonlinearity DNL — ±0.5 ±1 LSB No missing codes Offset Error — ±0.75 ±2 LSB Gain Error — -1 ±3 LSB Dynamic Performance Total Harmonic Distortion THD — -82 — dB V = 0.1V to 4.9V @ 1 kHz IN Signal-to-Noise and Distortion SINAD — 72 — dB V = 0.1V to 4.9V @ 1 kHz IN Spurious-Free Dynamic Range SFDR — 86 — dB V = 0.1V to 4.9V @ 1 kHz IN Analog Input Input Voltage Range V -0.3 — V +0.3 V 2.7V ≤ V ≤ 5.5V SS DD DD Leakage Current -1 — +1 µA SDA/SCL (open-drain output): Data Coding Format Straight Binary High-level input voltage V 0.7 V —— V IH DD Low-level input voltage V — — 0.3 V V IL DD Low-level output voltage V —— 0.4 VI = 3 mA, R = 1.53 kΩ OL OL PU —0.05V —V f = 400 kHz only Hysteresis of Schmitt trigger inputs V HYST DD SCL Note 1: “Sample time” is the time between conversions once the address byte has been sent to the converter. Refer to Figure 5-6. 2: This parameter is periodically sampled and not 100% tested. = Pull-up resistor on SDA and SCL. 3: R PU 4: SDA and SCL = V to V at 400 kHz. SS DD 5: t and t are dependent on internal oscillator timing. See Figure 5-5 and Figure 5-6 for relation to ACQ CONV SCL. DS21732B-page 2  2003 Microchip Technology Inc. MCP3221 DC ELECTRICAL SPECIFICATIONS (CONTINUED) Electrical Characteristics: Unless otherwise noted, all parameters apply at V = 5.0V, V = GND, R = 2 kΩ DD SS PU 2 = -40°C to +85°C, I C Fast Mode Timing: f = 400 kHz (Note 3). T AMB SCL Parameters Sym Min Typ Max Units Conditions Input leakage current I -1 — +1 µA V = 0.1 V and 0.9 V LI IN DD DD Output leakage current I -1 — +1 µA V = 0.1 V and 0.9 V LO OUT SS DD Pin capacitance C , — — 10 pF T = 25°C, f = 1 MHz; IN AMB (all inputs/outputs) C (Note 2) OUT Bus Capacitance C — — 400 pF SDA drive low, 0.4V B Power Requirements Operating Voltage V 2.7 — 5.5 V DD Conversion Current I — 175 250 µA DD Standby Current I — 0.005 1 µA SDA, SCL = V DDS DD Active bus current I — — 120 µA Note 4 DDA Conversion Rate Conversion Time t —8.96 — µs Note 5 CONV Analog Input Acquisition Time t —1.12 — µs Note 5 ACQ Sample Rate f — — 22.3 ksps f = 400 kHz (Note 1) SAMP SCL Note 1: “Sample time” is the time between conversions once the address byte has been sent to the converter. Refer to Figure 5-6. 2: This parameter is periodically sampled and not 100% tested. 3: R = Pull-up resistor on SDA and SCL. PU 4: SDA and SCL = V to V at 400 kHz. SS DD and t are dependent on internal oscillator timing. See Figure 5-5 and Figure 5-6 for relation to 5: t ACQ CONV SCL. TEMPERATURE SPECIFICATIONS Electrical Characteristics: Unless otherwise noted, all parameters apply at V = 5.0V, V = GND. DD SS Parameters Symbol Min Typ Max Units Conditions Temperature Ranges Industrial Temperature Range T -40 — +85 °C A Extended Temperature Range T -40 — +125 °C A Operating Temperature Range T -40 — +125 °C A Storage Temperature Range T -65 — +150 °C A Thermal Package Resistances Thermal Resistance, 5L-SOT23A — — θ 256 °C/W JA  2003 Microchip Technology Inc. DS21732B-page 3 MCP3221 TIMING SPECIFICATIONS Electrical Characteristics: All parameters apply at V = 2.7V - 5.5V, V = GND, T = -40°C to +85°C. DD SS AMB Parameters Sym Min Typ Max Units Conditions 2 I C Standard Mode Clock frequency f 0 — 100 kHz SCL Clock high time T 4000 — — ns HIGH Clock low time T 4700 — — ns LOW SDA and SCL rise time T — — 1000 ns From V to V (Note 1) R IL IH SDA and SCL fall time T — — 300 ns From V to V (Note 1) F IL IH START condition hold time T 4000 — — ns HD:STA START condition setup time T 4700 — — ns SU:STA Data input setup time T 250 — — ns SU:DAT STOP condition setup time T 4000 — — ns SU:STO STOP condition hold time T 4000 — — ns HD:STD Output valid from clock T — — 3500 ns AA Bus free time T 4700 — — ns Note 2 BUF Input filter spike suppression T — — 50 ns SDA and SCL pins (Note 1) SP 2 I C Fast Mode Clock frequency F 0 — 400 kHz SCL Clock high time T 600 — — ns HIGH Clock low time T 1300 — — ns LOW SDA and SCL rise time T 20 + 0.1C — 300 ns From V to V (Note 1) R B IL IH SDA and SCL fall time T 20 + 0.1C — 300 ns From V to V (Note 1) F B IL IH START condition hold time T 600 — — ns HD:STA START condition setup time T 600 — — ns SU:STA Data input hold time T 0— 0.9 ms HD:DAT Data input setup time T 100 — — ns SU:DAT STOP condition setup time T 600 — — ns SU:STO STOP condition hold time T 600 — — ns HD:STD Output valid from clock T — — 900 ns AA Bus free time T 1300 — — ns Note 2 BUF Input filter spike suppression T — — 50 ns SDA and SCL pins (Note 1) SP Note 1: This parameter is periodically sampled and not 100% tested. 2: Time the bus must be free before a new transmission can start. T HIGH V HYS T T F R SCL T SU:STA T T T T SU:STO HD:DAT SU:DAT LOW SDA T HD:STA IN T SP T BUF T AA SDA OUT FIGURE 1-1: Standard and Fast Mode Bus Timing Data. DS21732B-page 4  2003 Microchip Technology Inc. MCP3221 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. 2 Note: Unless otherwise indicated, V = 5V, V = 0V, I C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion DD SS = 22.3 ksps), T = +25°C. Mode (f SAMP A 1 1 0.8 0.8 0.6 Positive INL 0.6 0.4 0.4 Positive INL 0.2 0.2 0 0 -0.2 -0.2 Negative INL -0.4 -0.4 Negative INL -0.6 -0.6 -0.8 -0.8 -1 -1 0 100 200 300 400 0 100 200 300 400 2 2 I C Bus Rate (kHz) I C Bus Rate (kHz) FIGURE 2-1: INL vs. Clock Rate. FIGURE 2-4: INL vs. Clock Rate (V =2.7V). DD 1 1 0.8 0.8 Positive INL 0.6 0.6 0.4 0.4 Positive INL 0.2 0.2 0 0 -0.2 -0.2 Negative INL -0.4 -0.4 Negative INL -0.6 -0.6 -0.8 -0.8 -1 -1 2.533.5 44.555.5 2.533.5 44.555.5 V (V) DD V (V) DD 2 2 FIGURE 2-2: INL vs. V - I C™ FIGURE 2-5: INL vs. V - I C™ Fast DD DD Standard Mode (f = 100 kHz). Mode (f = 400 kHz). SCL SCL 2 2 1.5 1.5 1 1 0.5 0.5 0 0 -0.5 -0.5 -1 -1 -1.5 -1.5 -2 -2 0 1024 2048 3072 4096 0 1024 2048 3072 4096 Digital Code Digital Code FIGURE 2-3: INL vs. Code FIGURE 2-6: INL vs. Code (Representative Part). (Representative Part, V = 2.7V). DD  2003 Microchip Technology Inc. DS21732B-page 5 INL (LSB) INL (LSB) INL (LSB) INL (LSB) INL (LSB) INL (LSB) MCP3221 2 = 5V, V = 0V, I C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion Note: Unless otherwise indicated, V DD SS Mode (f = 22.3 ksps), T = +25°C. SAMP A 1 1 0.8 0.8 Positive INL 0.6 0.6 Positive INL 0.4 0.4 0.2 0.2 0 0 -0.2 -0.2 Negative INL -0.4 -0.4 -0.6 -0.6 Negative INL -0.8 -0.8 -1 -1 -50 -25 0 255075 100 125 -50 -25 0 255075 100 125 Temperature (°C) Temperature (°C) FIGURE 2-7: INL vs. Temperature. FIGURE 2-10: INL vs. Temperature (V =2.7V). DD 1 1 0.8 0.8 0.6 0.6 Positive DNL 0.4 0.4 0.2 Positive DNL 0.2 0 0 -0.2 -0.2 -0.4 -0.4 Negative DNL Negative DNL -0.6 -0.6 -0.8 -0.8 -1 -1 0 100 200 300 400 0 100 200 300 400 2 2 I C Bus Rate (kHz) I C Bus Rate (kHz) FIGURE 2-8: DNL vs. Clock Rate. FIGURE 2-11: DNL vs. Clock Rate (V =2.7V). DD 1 1 0.8 0.8 0.6 0.6 Positive DNL Positive DNL 0.4 0.4 0.2 0.2 0 0 -0.2 -0.2 -0.4 Negative DNL -0.4 Negative DNL -0.6 -0.6 -0.8 -0.8 -1 -1 2.533.5 44.5 55.5 2.5 3.5 4.5 5.5 V (V) DD V (V) DD 2 2 FIGURE 2-9: DNL vs. V - I C™ FIGURE 2-12: DNL vs. V - I C™ Fast DD DD Standard Mode (f = 100 kHz). Mode (f = 400 kHz). SCL SCL DS21732B-page 6  2003 Microchip Technology Inc. DNL (LSB) DNL (LSB) INL (LSB) DNL (LSB) DNL (LSB) INL (LSB) MCP3221 2 = 5V, V = 0V, I C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion Note: Unless otherwise indicated, V DD SS Mode (f = 22.3 ksps), T = +25°C. SAMP A 1 1 0.8 0.8 0.6 0.6 0.4 0.4 0.2 0.2 0 0 -0.2 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 -1 -1 0 1024 2048 3072 4096 0 1024 2048 3072 4096 Digital Code Digital Code FIGURE 2-13: DNL vs. Code FIGURE 2-16: DNL vs. Code (Representative Part). (Representative Part, V = 2.7V). DD 1 1 0.8 0.8 0.6 0.6 Positive DNL 0.4 0.4 Positive DNL 0.2 0.2 0 0 -0.2 -0.2 Negative DNL -0.4 -0.4 Negative DNL -0.6 -0.6 -0.8 -0.8 -1 -1 -50 -25 0 255075 100 125 -50 -25 0 255075 100 125 Temperature (°C) Temperature (°C) FIGURE 2-14: DNL vs. Temperature. FIGURE 2-17: DNL vs. Temperature (V =2.7V). DD 1 0 f = 100 kHz & 400 kHz SCL 0.9 -0.1 -0.2 0.8 -0.3 0.7 -0.4 0.6 Fast Mode -0.5 (f =100 kHz) Standard Mode SCL 0.5 (f =400 kHz) SCL -0.6 0.4 -0.7 0.3 -0.8 0.2 -0.9 0.1 -1 0 2.533.5 44.555.5 2.533.5 4 4.555.5 V (V) DD V (V) DD FIGURE 2-15: Gain Error vs. V . FIGURE 2-18: Offset Error vs. V . DD DD  2003 Microchip Technology Inc. DS21732B-page 7 Gain Error (LSB) DNL (LSB) DNL (LSB) Offset Error (LSB) DNL (LSB) DNL (LSB) MCP3221 2 = 5V, V = 0V, I C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion Note: Unless otherwise indicated, V DD SS Mode (f = 22.3 ksps), T = +25°C. SAMP A 3 2 1.8 2 1.6 V = 2.7V 1.4 DD 1 V = 5V DD 1.2 0 1 0.8 -1 0.6 0.4 -2 0.2 V = 5V V = 2.7V DD DD -3 0 -50 -25 0 25 50 75 100 125 -50 -25 0 25 50 75 100 125 Temperature (°C) Temperature (°C) FIGURE 2-19: Gain Error vs. Temperature. FIGURE 2-22: Offset Error vs. Temperature. 100 100 V = 5V 90 DD V = 5V 90 DD 80 80 70 70 60 60 V = 2.7V DD 50 V = 2.7V DD 50 40 40 30 30 20 20 10 10 0 0 110 110 Input Frequency (kHz) Input Frequency (kHz) FIGURE 2-20: SNR vs. Input Frequency. FIGURE 2-23: SINAD vs. Input Frequency. 0 80 V = 5V -10 DD 70 -20 60 -30 50 -40 V = 5V V = 2.7V DD DD -50 40 V = 2.7V DD -60 30 -70 20 -80 10 -90 -100 0 110 -40 -30 -20 -10 0 Input Frequency (kHz) Input Signal Level (dB) FIGURE 2-21: THD vs. Input Frequency. FIGURE 2-24: SINAD vs. Input Signal Level. DS21732B-page 8  2003 Microchip Technology Inc. THD (dB) SNR (dB) Gain Error (LSB) SINAD (dB) SINAD (dB) Offset Error (LSB) MCP3221 2 = 5V, V = 0V, I C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion Note: Unless otherwise indicated, V DD SS Mode (f = 22.3 ksps), T = +25°C. SAMP A 12 12 11.95 11.5 11.9 11.85 V = 2.7V DD 11 11.8 V = 5V DD 11.75 10.5 11.7 10 11.65 11.6 9.5 11.55 11.5 9 2.5 3 3.5 4 4.5 5 5.5 110 V (V) DD Input Frequency (kHz) FIGURE 2-25: ENOB vs. V . FIGURE 2-28: ENOB vs. Input Frequency. DD 100 10 V = 5V DD 90 f = 5.6 ksps SAMP -10 80 70 -30 60 V = 2.7V DD -50 50 -70 40 30 -90 20 -110 10 -130 0 0 500 1000 1500 2000 2500 110 Frequency (Hz) Input Frequency (kHz) 2 FIGURE 2-26: SFDR vs. Input Frequency. FIGURE 2-29: Spectrum Using I C™ Standard Mode (Representative Part, 1 kHz Input Frequency). 250 10 200 -10 -30 150 -50 100 -70 -90 50 -110 0 -130 2.5 3 3.5 4 4.5 5 5.5 0 2000 4000 6000 8000 10000 V (V) DD Frequency (Hz) 2 FIGURE 2-30: I (Conversion) vs. V . FIGURE 2-27: Spectrum Using I C™ Fast DD DD Mode (Representative Part, 1 kHz Input Frequency).  2003 Microchip Technology Inc. DS21732B-page 9 Amplitude (dB) SFDR (dB) ENOB (rms) I (µA) Amplitude (dB) ENOB (rms) DD MCP3221 2 = 5V, V = 0V, I C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion Note: Unless otherwise indicated, V DD SS Mode (f = 22.3 ksps), T = +25°C. SAMP A 200 100 90 180 160 80 140 70 120 60 100 50 V = 5V DD V = 5V DD 40 80 60 30 V = 2.7V 40 20 DD V = 2.7V DD 20 10 0 0 0 100 200 300 400 0 100 200 300 400 2 2 I C Clock Rate (kHz) I C Clock Rate (kHz) FIGURE 2-31: I (Conversion) vs. Clock FIGURE 2-34: I (Active Bus) vs. Clock DD DDA Rate. Rate. 250 100 90 200 80 V = 5V DD V = 5V DD 70 150 60 50 100 40 V = 2.7V DD 30 V = 2.7V DD 50 20 10 0 0 -50 -25 0 25 50 75 100 125 -50 -25 0 25 50 75 100 125 Temperature (°C) Temperature (°C) FIGURE 2-32: I (Conversion) vs. FIGURE 2-35: I (Active Bus) vs. DD DDA Temperature. Temperature. 100 60 90 50 80 70 40 60 50 30 40 20 30 20 10 10 0 0 2.533.5 44.555.5 2.5 3 3.544.555.5 V (V) V (V) DD DD FIGURE 2-33: I (Active Bus) vs. V . FIGURE 2-36: I (Standby) vs. V . DDA DD DDS DD DS21732B-page 10  2003 Microchip Technology Inc. I (µA) I (µA) I (µA) DDA DD DD I (pA) I (µA) I (µA) DDS DDA DDA MCP3221 2 = 5V, V = 0V, I C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion Note: Unless otherwise indicated, V DD SS Mode (f = 22.3 ksps), T = +25°C. SAMP A 2.1 Test Circuits 1000 100 V = 5V 10 DD 1 0.1 10 µF 0.1 µF 0.01 2kΩ 2kΩ 0.001 V 0.0001 DD AIN SDA MCP3221 -50 -25 0 255075 100 125 V SCL SS Temperature (°C) V IN FIGURE 2-37: I (Standby) vs. DDS Temperature. V = 2.5V CM 2 1.8 1.6 FIGURE 2-39: Typical Test Configuration. 1.4 1.2 1 0.8 0.6 0.4 0.2 0 -50 -25 0 255075 100 125 Temperature (°C) FIGURE 2-38: Analog Input Leakage vs. Temperature.  2003 Microchip Technology Inc. DS21732B-page 11 Analog Input Leakage (nA) I (nA) DDS MCP3221 3.0 PIN FUNCTIONS 3.3 Serial Data (SDA) SDA is a bidirectional pin used to transfer addresses TABLE 3-1: PIN FUNCTION TABLE and data into and out of the device. Since it is an open- drain terminal, the SDA bus requires a pull-up resistor Name Function to V (typically 10kΩ for 100kHz and 2kΩ for DD V +2.7V to 5.5V Power Supply DD 400kHz SCL clock speeds). Refer to Section6.2, 2 V Ground “Connecting to the I C Bus”, for more information. SS AIN Analog Input For normal data transfer, SDA is allowed to change only SDA Serial Data In/Out during SCL low. Changes during SCL high are reserved for indicating the START and STOP conditions. Refer to SCL Serial Clock In 2 Section 5.1, “I C Bus Characteristics”. 3.1 V and V DD SS 3.4 Serial Clock (SCL) The V pin, with respect to V , provides power to the DD SS SCL is an input pin used to synchronize the data trans- device as well as a voltage reference for the conversion fer to and from the device on the SDA pin and is an process. Refer to Section6.4, “Device Power and open-drain terminal. Therefore, the SCL bus requires a Layout Considerations”, for tips on power and pull-up resistor to V (typically 10 kΩ for 100 kHz and DD grounding. 2kΩ for 400kHz SCL clock speeds. Refer to 2 C Bus”). Section 6.2, “Connecting to the I 3.2 Analog Input (AIN) For normal data transfer, SDA is allowed to change AIN is the input pin to the sample-and-hold circuitry of only during SCL low. Changes during SCL high are the Successive Approximation Register (SAR) con- reserved for indicating the START and STOP verter. Care should be taken in driving this pin. Refer to conditions. Refer to Section 6.1, “Driving the Analog Section 6.1, “Driving the Analog Input”. For proper con- Input”. versions, the voltage on this pin can vary from V to SS V . DD DS21732B-page 12  2003 Microchip Technology Inc. MCP3221 4.0 DEVICE OPERATION 4.2 Conversion Time (t ) CONV The conversion time is the time required to obtain the The MCP3221 employs a classic SAR architecture. This architecture uses an internal sample and hold digital result once the analog input is disconnected from the holding capacitor. With the MCP3221, the capacitor to store the analog input while the conversion specified conversion time is typically 8.96 µs. This time is taking place. At the end of the acquisition time, the input switch of the converter opens and the device uses is dependent on the internal oscillator and is independent of SCL. the collected charge on the internal sample-and-hold capacitor to produce a serial 12-bit digital output code. 4.3 Acquisition Time (t ) The acquisition time and conversion is self-timed using ACQ an internal clock. After each conversion, the results are The acquisition time is the amount of time the sample stored in a 12-bit register that can be read at any time. cap array is acquiring charge. Communication with the device is accomplished with a The acquisition time is, typically, 1.12 µs. This time is 2 2-wire, I C interface. Maximum sample rates of dependent on the internal oscillator and independent of 22.3 ksps are possible with the MCP3221 in a continu- SCL. ous-conversion mode and an SCL clock rate of 400 kHz. 4.4 Sample Rate 4.1 Digital Output Code Sample rate is the inverse of the maximum amount of time that is required from the point of acquisition of the The digital output code produced by the MCP3221 is a first conversion to the point of acquisition of the second function of the input signal and power supply voltage, conversion. V . As the V level is reduced, the LSB size is DD DD The sample rate can be measured either by single or reduced accordingly. The theoretical LSB size is shown continuous conversions. A single conversion includes below. a Start Bit, Address Byte, Two Data Bytes and a Stop bit. This sample rate is measured from one Start Bit to EQUATION the next Start Bit. V DD ------------ For continuous conversions (requested by the Master LSB SIZE = 4096 by issuing an acknowledge after a conversion), the maximum sample rate is measured from conversion to V = Supply voltage DD conversion or a total of 18 clocks (two data bytes and two Acknowledge bits). Refer to Section 5-2, “Device The output code of the MCP3221 is transmitted serially Addressing”. with MSB first. The format of the code is straight binary. Output Code 1111 1111 1111 (4095) 1111 1111 1110 (4094) 0000 0000 0011 (3) 0000 0000 0010 (2) 0000 0000 0001 (1) 0000 0000 0000 (0) AIN .5 LSB V -1.5 LSB DD 1.5 LSB V -2.5 LSB DD 2.5 LSB FIGURE 4-1: Transfer Function.  2003 Microchip Technology Inc. DS21732B-page 13 MCP3221 4.5 Differential Non-Linearity (DNL) 4.8 Gain Error In the ideal A/D converter transfer function, each code The gain error determines the amount of deviation from has a uniform width. That is, the difference in analog the ideal slope of the A/D converter transfer function. input voltage is constant from one code transition point Before the gain error is determined, the offset error is to the next. Differential nonlinearity (DNL) specifies the measured and subtracted from the conversion result. deviation of any code in the transfer function from an The gain error can then be determined by finding the ideal code width of 1 LSB. The DNL is determined by location of the last code transition and comparing that subtracting the locations of successive code transition location to the ideal location. The ideal location of the . points after compensating for any gain and offset last code transition is 1.5 LSBs below full-scale or V DD errors. A positive DNL implies that a code is longer than 4.9 Conversion Current (I ) the ideal code width, while a negative DNL implies that DD a code is shorter than the ideal width. The average amount of current over the time required to perform a 12-bit conversion. 4.6 Integral Non-Linearity (INL) Integral nonlinearity (INL) is a result of cumulative DNL 4.10 Active Bus Current (I ) DDA errors and specifies how much the overall transfer The average amount of current over the time required function deviates from a linear response. The method 2 to monitor the I C bus. Any current the device con- of measurement used in the MCP3221 A/D converter sumes while it is not being addressed is referred to as to determine INL is the “end-point” method. “Active Bus” current. 4.7 Offset Error 4.11 Standby Current (I ) DDS Offset error is defined as a deviation of the code transi- The average amount of current required while no con- tion points that are present across all output codes. version is occurring and while no data is being output This has the effect of shifting the entire A/D transfer (i.e., SCL and SDA lines are quiet). function. The offset error is measured by finding the dif- ference between the actual location of the first code 2 4.12 I C Standard Mode Timing transition and the desired location of the first transition. 2 The ideal location of the first code transition is located I C specification where the frequency of SCL is at 1/2 LSB above V . 100 kHz. SS 2 4.13 I C Fast Mode Timing 2 I C specification where the frequency of SCL is 400 kHz. DS21732B-page 14  2003 Microchip Technology Inc. MCP3221 Each data transfer is initiated with a START condition 5.0 SERIAL COMMUNICATIONS and terminated with a STOP condition. The number of 2 data bytes transferred between the START and STOP 5.1 I C Bus Characteristics conditions is determined by the master device and is The following bus protocol has been defined: unlimited. • Data transfer may be initiated only when the bus 5.1.5 ACKNOWLEDGE is not busy. • During data transfer, the data line must remain Each receiving device, when addressed, is obliged to stable whenever the clock line is high. Changes in generate an acknowledge bit after the reception of the data line while the clock line is high will be each byte. The master device must generate an extra interpreted as a START or STOP condition. clock pulse which is associated with this acknowledge bit. Accordingly, the following bus conditions have been defined (refer to Figure 5-1). The device that acknowledges has to pull down the SDA line during the acknowledge clock pulse in such a 5.1.1 BUS NOT BUSY (A) way that the SDA line is stable-low during the high period of the acknowledge-related clock pulse. Setup Both data and clock lines remain high. and hold times must be taken into account. During reads, a master device must signal an end of data to 5.1.2 START DATA TRANSFER (B) the slave by not generating an acknowledge bit on the A high-to-low transition of the SDA line while the clock last byte that has been clocked out of the slave (NAK). (SCL) is high determines a START condition. All In this case, the slave (MCP3221) will release the bus commands must be preceded by a START condition. to allow the master device to generate the STOP condition. 5.1.3 STOP DATA TRANSFER (C) The MCP3221 supports a bidirectional, 2-wire bus and A low-to-high transition of the SDA line while the clock data transmission protocol. The device that sends data (SCL) is high determines a STOP condition. All onto the bus is the transmitter and the device receiving operations must be ended with a STOP condition. data is the receiver. The bus has to be controlled by a master device which generates the serial clock (SCL), 5.1.4 DATA VALID (D) controls the bus access and generates the START and STOP conditions, while the MCP3221 works as a slave The state of the data line represents valid data when, device. Both master and slave devices can operate as after a START condition, the data line is stable for the either transmitter or receiver, but the master device duration of the clock signal’s high period. determines which mode is activated. The data on the line must be changed during the low period of the clock signal. There is one clock pulse per bit of data. (A) (B) (D) (D) (C) (A) SCL SDA START STOP ADDRESS OR DATA CONDITION CONDITION ACKNOWLEDGE ALLOWED VALID TO CHANGE FIGURE 5-1: Data Transfer Sequence on the Serial Bus.  2003 Microchip Technology Inc. DS21732B-page 15 MCP3221 5.2 Device Addressing 5.3 Executing a Conversion The address byte is the first byte received following the This section will describe the details of communicating START condition from the master device. The first part with the MCP3221 device. Initiating the sample-and- of the control byte consists of a 4-bit device code, hold acquisition, reading the conversion data and which is set to 1010 for the MCP3221. The device code executing multiple conversions will be discussed. is followed by three address bits: A2, A1 and A0. The 5.3.1 INITIATING THE SAMPLE AND default address bits are 1001. Contact the Microchip HOLD factory for additional address bit options. The address bits allow up to eight MCP3221 devices on the same The acquisition and conversion of the input signal bus and are used to determine which device is begins with the falling edge of the R/W bit of the accessed. address byte. At this point, the internal clock initiates The eighth bit of the slave address determines if the the sample, hold and conversion cycle, all of which are master device wants to read conversion data or write to internal to the ADC. the MCP3221. When set to a ‘1’, a read operation is selected. When set to a ‘0’, a write operation is t + t is ACQ CONV selected. There are no writable registers on the initiated here MCP3221. Therefore, this bit must be set to a ’1’ in order to initiate a conversion. Address Byte The MCP3221 is a slave device that is compatible with 2 C 2-wire serial interface protocol. A hardware the I connection diagram is shown in Figure 6-2. Communi- SCL 1 234 56 7 8 9 cation is initiated by the microcontroller (master device), which sends a START bit followed by the address byte. 1 0 0 1 A2 A1 A0 R/W SDA On completion of the conversion(s) performed by the Start MCP3221, the microcontroller must send a STOP bit to Bit Device bits Address bits end communication. bit. The last bit in the device address byte is the R/W When this bit is a logic ‘1’, a conversion will be exe- FIGURE 5-3: Initiating the Conversion, cuted. Setting this bit to logic ‘0’ will also result in an Address Byte. “acknowledge” (ACK) from the MCP3221, with the device then releasing the bus. This can be used for device polling. Refer to Section 6.3, “Device Polling”, t + t is for more information. ACQ CONV initiated here START READ/WRITE Lower Data Byte (n) 17 18 19 20 21 22 23 24 25 26 SLAVE ADDRESS R/W A SCL SDA D8 D7 D6 D5 D4 D3 D2 D2 D0 1 0 0 1 1 0 1 FIGURE 5-4: Initiating the Conversion, (1) Device Code Address Bits Continuous Conversions. Note 1: Contact Microchip for additional address bits. FIGURE 5-2: Device Addressing. DS21732B-page 16  2003 Microchip Technology Inc. ACK ACK ACK MCP3221 The input signal will initially be sampled with the first 5.3.2 READING THE CONVERSION DATA falling edge of the clock following the transmission of a Once the MCP3221 acknowledges the address byte, logic-high R/W bit. Additionally, with the rising edge of the device will transmit four ‘0’ bits followed by the upper the SCL, the ADC will transmit an acknowledge bit four data bits of the conversion. The master device will (ACK = 0). The master must release the data bus dur- then acknowledge this byte with an ACK = Low. With the ing this clock pulse to allow the MCP3221 to pull the following 8 clock pulses, the MCP3221 will transmit the line low (refer to Figure 5-3). lower eight data bits from the conversion. The master For consecutive samples, sampling begins on the fall- then sends an ACK = high, indicating to the MCP3221 ing edge of the LSB of the conversion result, which is that no more data is requested. The master can then two bytes long. Refer to Figure 5-6 a for timing diagram. send a stop bit to end the transmission. t + t is ACQ CONV initiated here 12 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 SCL S T S Upper Data Byte Lower Data Byte Address Byte A T R O T P A A R N A A A D D D D D D D D D D D D C C / A SDA S 10 0 1 00 0 0 P 2 1 0 K 11 10 9 8 K 7 6 5 4 3 2 1 0 W K Device bits Address bits FIGURE 5-5: Executing a Conversion. 5.3.3 CONSECUTIVE CONVERSIONS For consecutive samples, sampling begins on the fall- ing edge of the LSB of the conversion result. See Figure 5-6 for timing. t + t is t + t is ACQ CONV ACQ CONV initiated here initiated here f = 22.3 ksps (f = 400 kHz) SAMP CLK 12 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 SCL S T Address Byte Upper Data Byte (n) Lower Data Byte (n) A R T A A A R D D D D D D D D D D D D C C C SDA S 1 0 0 1 A2 A1 A0 / 00 0 0 0 K 11 10 9 8 K 7 6 5 4 3 2 1 0 K W Device bits Address bits FIGURE 5-6: Continuous Conversion.  2003 Microchip Technology Inc. DS21732B-page 17 MCP3221 The analog input model is shown in Figure 6-1. In this 6.0 APPLICATIONS INFORMATION diagram, the source impedance (R ) adds to the inter- SS nal sampling switch (R ) impedance, directly affecting 6.1 Driving the Analog Input S ). the time required to charge the capacitor (C SAMPLE The MCP3221 has a single-ended analog input (AIN). Consequently, a larger source impedance increases For proper conversion results, the voltage at the AIN the offset error, gain error and integral linearity errors of pin must be kept between V and V . If the converter SS DD the conversion. Ideally, the impedance of the signal has no offset error, gain error, INL or DNL errors, and source should be near zero. This is achievable with an the voltage level of AIN is equal to or less than operational amplifier, such as the MCP6022, which has V + 1/2 LSB, the resultant code will be 000h. Addi- SS a closed-loop output impedance of tens of ohms. tionally, if the voltage at AIN is equal to or greater than V - 1.5 LSB, the output code will be FFFh. DD V DD Sampling Switch V = 0.6V T R = 1 kΩ AIN SS R S SS C SAMPLE C I PIN LEAKAGE V = DAC capacitance A V = 0.6V T 7pF ±1 nA = 20 pF V SS Legend VA = signal source R = source impedance SS AIN = analog input pad C = analog input pin capacitance PIN V = threshold voltage T I = leakage current at the pin LEAKAGE due to various junctions SS = sampling switch R = sampling switch resistor S C = sample/hold capacitance SAMPLE FIGURE 6-1: Analog Input Model, AIN. 2 The number of devices connected to the bus is limited 6.2 Connecting to the I C Bus only by the maximum bus capacitance of 400 pF. A 2 The I C bus is an open-collector bus, requiring pull-up possible configuration using multiple devices is shown resistors connected to the SDA and SCL lines. This in Figure 6-3. configuration is shown in Figure 6-2. SDA SCL V DD PIC16F876 Microcontroller MCP3221 R R 24LC01 PU PU EEPROM SDA AIN SCL Analog MCP3221 12-bit ADC Input Signal TC74 Temperature R is typically: 10 kΩ for f = 100 kHz PU SCL Sensor 2kΩ for f = 400 kHz SCL 2 FIGURE 6-2: Pull-up Resistors on I C 2 FIGURE 6-3: Multiple Devices on I C™ Bus. Bus. DS21732B-page 18  2003 Microchip Technology Inc. ® PICmicro Microcontroller MCP3221 Digital and analog traces should be separated as much 6.3 Device Polling as possible on the board, with no traces running under- In some instances, it may be necessary to test for neath the device or the bypass capacitor. Extra precau- 2 C bus without performing MCP3221 presence on the I tions should be taken to keep traces with high- a conversion. This operation is described in Figure 6-4. frequency signals (such as clock lines) as far as Here we are setting the R/W bit in the address byte to possible from analog traces. a zero. The MCP3221 will then acknowledge by pulling Use of an analog ground plane is recommended in SDA low during the ACK clock and then release the 2 order to keep the ground potential the same for all bus back to the I C master. A stop or repeated start bit devices on the board. Providing V connections to 2 DD can then be issued from the master and I C devices in a “star” configuration can also reduce noise communication can continue. by eliminating current return paths and associated errors (Figure 6-6). For more information on layout tips Address Byte when using the MCP3221 or other ADC devices, refer to AN688, “Layout Tips for 12-Bit A/D Converter SCL 12 3 4 5 6 7 8 9 Applications”. V DD 1 00 1 A2 A1A0 0 SDA Connection Start Start R/W Device bits Bit Bit Address bits MCP3221 response Device 4 Device 1 FIGURE 6-4: Device Polling. 6.4 Device Power and Layout Considerations Device 3 6.4.1 POWERING THE MCP3221 Device 2 V supplies the power to the device as well as the ref- DD erence voltage. A bypass capacitor value of 0.1 µF is recommended. Adding a 10 µF capacitor in parallel is FIGURE 6-6: V traces arranged in a recommended to attenuate higher frequency noise DD ‘Star’ configuration in order to reduce errors present in some systems. caused by current return paths. V DD 6.4.3 USING A REFERENCE FOR SUPPLY V DD The MCP3221 uses V as both power and a refer- DD 10 µF 0.1 µF ence. In some applications, it may be necessary to use a stable reference to achieve the required accuracy. V DD R R PU PU Figure 6-7 shows an example using the MCP1541 as a SCL AIN To 4.096V, 2% reference. MCP3221 SDA Microcontroller V DD V DD 1µF FIGURE 6-5: Powering the MCP3221. MCP1541 C L 4.096V 6.4.2 LAYOUT CONSIDERATIONS V DD R Reference PU SCL When laying out a printed circuit board for use with AIN MCP3221 analog components, care should be taken to reduce SDA noise wherever possible. A bypass capacitor from V DD to ground should always be used with this device and should be placed as close as possible to the device pin. A bypass capacitor value of 0.1 µF is recommended. FIGURE 6-7: Stable Power and Reference Configuration.  2003 Microchip Technology Inc. DS21732B-page 19 ACK 0.1 µF To Microcontroller MCP3221 7.0 PACKAGING INFORMATION 7.1 Package Marking Information 5-Pin SOT-23A (EIAJ SC-74) Device 3 2 1 cdef 4 5 Part Number Address Option SOT-23 MCP3221A0T-I/OT EE 000 MCP3221A1T-I/OT 001 EH MCP3221A2T-I/OT 010 EB MCP3221A3T-I/OT EC 011 MCP3221A4T-I/OT 100 ED MCP3221A5T-I/OT 101 S1 * MCP3221A6T-I/OT EF 110 MCP3221A7T-I/OT 111 EG MCP3221A0T-E/OT GE 000 MCP3221A1T-E/OT 001 GH MCP3221A2T-E/OT 010 GB MCP3221A3T-E/OT GC 011 MCP3221A4T-E/OT 100 GD MCP3221A5T-E/OT 101 GA * MCP3221A6T-E/OT GF 110 MCP3221A7T-E/OT 111 GG * Default option. Contact Microchip Factory for other address options. Legend: 1 Part Number code + temperature range 2 Part Number code + temperature range 3 Year and work week 4 Lot ID Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information. * Standard device marking consists of Microchip part number, year code, week code, and traceability code. DS21732B-page 20  2003 Microchip Technology Inc. MCP3221 5-Lead Plastic Small Outline Transistor (OT) (SOT23) E E1 p B p1 D n 1 α c A A2 φ A1 L β Units INCHES* MILLIMETERS Dimension Limits MIN NOM MAX MIN NOM MAX Number of Pins n 5 5 p Pitch .038 0.95 p1 Outside lead pitch (basic) .075 1.90 Overall Height A .035 .046 .057 0.90 1.18 1.45 Molded Package Thickness A2 .035 .043 .051 0.90 1.10 1.30 Standoff § A1 .000 .003 .006 0.00 0.08 0.15 Overall Width E .102 .110 .118 2.60 2.80 3.00 Molded Package Width E1 .059 .064 .069 1.50 1.63 1.75 Overall Length D .110 .116 .122 2.80 2.95 3.10 Foot Length L .014 .018 .022 0.35 0.45 0.55 φ Foot Angle 0 5 10 0 5 10 c Lead Thickness .004 .006 .008 0.09 0.15 0.20 Lead Width B .014 .017 .020 0.35 0.43 0.50 α Mold Draft Angle Top 0 5 10 0 5 10 Mold Draft Angle Bottom β 0 5 10 0 5 10 * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MO-178 Drawing No. C04-091  2003 Microchip Technology Inc. DS21732B-page 21 MCP3221 NOTES: DS21732B-page 22  2003 Microchip Technology Inc. MCP3221 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. Examples: PART NO. XX X /XX a) MCP3221A0T-I/OT: Industrial, A0 Address, Device Address Temperature Package Tape and Reel Options Range b) MCP3221A1T-I/OT: Industrial, A1 Address, Tape and Reel c) MCP3221A2T-I/OT: Industrial, A2 Address, Device: MCP3221T: 12-Bit 2-Wire Serial A/D Converter Tape and Reel (Tape and Reel) d) MCP3221A3T-I/OT: Industrial, A3 Address, Tape and Reel Temperature Range: I = -40°C to +85°C e) MCP3221A4T-I/OT: Industrial, A4 Address, E= -40°C to +125°C Tape and Reel f) MCP3221A5T-I/OT: Industrial, A5 Address, Address Options: XX A2 A1 A0 Tape and Reel A0 = 0 0 0 g) MCP3221A6T-I/OT: Industrial, A6 Address, Tape and Reel A1 = 0 0 1 h) MCP3221A7T-I/OT: Industrial, A7 Address, A2 = 0 1 0 Tape and Reel A3 = 0 1 1 a) MCP3221A0T-E/OT: Extended, A0 Address, A4 = 1 0 0 Tape and Reel A5 * = 1 0 1 b) MCP3221A1T-E/OT: Extended, A1 Address, A6 = 1 1 0 Tape and Reel A7 = 1 1 1 c) MCP3221A2T-E/OT: Extended, A2 Address, Tape and Reel * Default option. Contact Microchip factory for other address options d) MCP3221A3T-E/OT: Extended, A3 Address, Tape and Reel e) MCP3221A4T-E/OT: Extended, A4 Address, Package: OT = SOT-23, 5-lead (Tape and Reel) Tape and Reel f) MCP3221A5T-E/OT: Extended, A5 Address, Tape and Reel g) MCP3221A6T-E/OT: Extended, A6 Address, Tape and Reel h) MCP3221A7T-IE/OT: Extended, A7 Address, Tape and Reel Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. Your local Microchip sales office 2. The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 3. The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products.  2003 Microchip Technology Inc. DS21732B-page 23 MCP3221 NOTES: DS21732B-page 24  2003 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device Trademarks applications and the like is intended through suggestion only The Microchip name and logo, the Microchip logo, dsPIC, and may be superseded by updates. It is your responsibility to KEELOQ, MPLAB, PIC, PICmicro, PICSTART, PRO MATE and ensure that your application meets with your specifications. PowerSmart are registered trademarks of Microchip No representation or warranty is given and no liability is Technology Incorporated in the U.S.A. and other countries. assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of FilterLab, microID, MXDEV, MXLAB, PICMASTER, SEEVAL patents or other intellectual property rights arising from such and The Embedded Control Solutions Company are use or otherwise. Use of Microchip’s products as critical registered trademarks of Microchip Technology Incorporated components in life support systems is not authorized except in the U.S.A. with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual Accuron, Application Maestro, dsPICDEM, dsPICDEM.net, property rights. ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In- Circuit Serial Programming, ICSP, ICEPIC, microPort, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, PICC, PICkit, PICDEM, PICDEM.net, PowerCal, PowerInfo, PowerMate, PowerTool, rfLAB, rfPIC, Select Mode, SmartSensor, SmartShunt, SmartTel and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. Serialized Quick Turn Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2003, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999 and Mountain View, California in March 2002. The Company’s quality system processes and procedures are QS-9000 compliant for its ® ® PICmicro 8-bit MCUs, KEELOQ code hopping devices, Serial EEPROMs, microperipherals, non-volatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001 certified. DS21732B-page 25  2003 Microchip Technology Inc. M WORLDWIDE SALES AND SERVICE Japan AMERICAS ASIA/PACIFIC Microchip Technology Japan K.K. Corporate Office Australia Benex S-1 6F 2355 West Chandler Blvd. Microchip Technology Australia Pty Ltd 3-18-20, Shinyokohama Chandler, AZ 85224-6199 Marketing Support Division Kohoku-Ku, Yokohama-shi Tel: 480-792-7200 Fax: 480-792-7277 Suite 22, 41 Rawson Street Kanagawa, 222-0033, Japan Technical Support: 480-792-7627 Epping 2121, NSW Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Web Address: http://www.microchip.com Australia Korea Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 Atlanta Microchip Technology Korea China - Beijing 3780 Mansell Road, Suite 130 168-1, Youngbo Bldg. 3 Floor Microchip Technology Consulting (Shanghai) Alpharetta, GA 30022 Samsung-Dong, Kangnam-Ku Co., Ltd., Beijing Liaison Office Tel: 770-640-0034 Fax: 770-640-0307 Seoul, Korea 135-882 Unit 915 Tel: 82-2-554-7200 Fax: 82-2-558-5934 Boston Bei Hai Wan Tai Bldg. 2 Lan Drive, Suite 120 Singapore No. 6 Chaoyangmen Beidajie Westford, MA 01886 Microchip Technology Singapore Pte Ltd. Beijing, 100027, No. China Tel: 978-692-3848 Fax: 978-692-3821 200 Middle Road Tel: 86-10-85282100 Fax: 86-10-85282104 #07-02 Prime Centre Chicago China - Chengdu Singapore, 188980 333 Pierce Road, Suite 180 Microchip Technology Consulting (Shanghai) Tel: 65-6334-8870 Fax: 65-6334-8850 Itasca, IL 60143 Co., Ltd., Chengdu Liaison Office Taiwan Tel: 630-285-0071 Fax: 630-285-0075 Rm. 2401-2402, 24th Floor, Microchip Technology (Barbados) Inc., Ming Xing Financial Tower Dallas Taiwan Branch No. 88 TIDU Street 4570 Westgrove Drive, Suite 160 11F-3, No. 207 Chengdu 610016, China Addison, TX 75001 Tung Hua North Road Tel: 86-28-86766200 Fax: 86-28-86766599 Tel: 972-818-7423 Fax: 972-818-2924 Taipei, 105, Taiwan China - Fuzhou Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 Detroit Microchip Technology Consulting (Shanghai) Tri-Atria Office Building Co., Ltd., Fuzhou Liaison Office EUROPE 32255 Northwestern Highway, Suite 190 Unit 28F, World Trade Plaza Farmington Hills, MI 48334 Austria No. 71 Wusi Road Tel: 248-538-2250 Fax: 248-538-2260 Microchip Technology Austria GmbH Fuzhou 350001, China Durisolstrasse 2 Kokomo Tel: 86-591-7503506 Fax: 86-591-7503521 A-4600 Wels 2767 S. Albright Road China - Hong Kong SAR Austria Kokomo, IN 46902 Microchip Technology Hongkong Ltd. Tel: 43-7242-2244-399 Tel: 765-864-8360 Fax: 765-864-8387 Unit 901-6, Tower 2, Metroplaza Fax: 43-7242-2244-393 223 Hing Fong Road Los Angeles Denmark Kwai Fong, N.T., Hong Kong 18201 Von Karman, Suite 1090 Microchip Technology Nordic ApS Tel: 852-2401-1200 Fax: 852-2401-3431 Irvine, CA 92612 Regus Business Centre Tel: 949-263-1888 Fax: 949-263-1338 China - Shanghai Lautrup hoj 1-3 Microchip Technology Consulting (Shanghai) Ballerup DK-2750 Denmark Phoenix Co., Ltd. Tel: 45-4420-9895 Fax: 45-4420-9910 2355 West Chandler Blvd. Room 701, Bldg. B France Chandler, AZ 85224-6199 Far East International Plaza Microchip Technology SARL Tel: 480-792-7966 Fax: 480-792-4338 No. 317 Xian Xia Road Parc d’Activite du Moulin de Massy San Jose Shanghai, 200051 43 Rue du Saule Trapu Microchip Technology Inc. Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 Batiment A - ler Etage 2107 North First Street, Suite 590 China - Shenzhen 91300 Massy, France San Jose, CA 95131 Microchip Technology Consulting (Shanghai) Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Tel: 408-436-7950 Fax: 408-436-7955 Co., Ltd., Shenzhen Liaison Office Germany Rm. 1812, 18/F, Building A, United Plaza Toronto Microchip Technology GmbH No. 5022 Binhe Road, Futian District 6285 Northam Drive, Suite 108 Steinheilstrasse 10 Shenzhen 518033, China Mississauga, Ontario L4V 1X5, Canada D-85737 Ismaning, Germany Tel: 86-755-82901380 Fax: 86-755-8295-1393 Tel: 905-673-0699 Fax: 905-673-6509 Tel: 49-89-627-144-0 China - Qingdao Fax: 49-89-627-144-44 Rm. B505A, Fullhope Plaza, Italy No. 12 Hong Kong Central Rd. Microchip Technology SRL Qingdao 266071, China Via Quasimodo, 12 Tel: 86-532-5027355 Fax: 86-532-5027205 20025 Legnano (MI) Milan, Italy India Tel: 39-0331-742611 Fax: 39-0331-466781 Microchip Technology Inc. India Liaison Office United Kingdom Marketing Support Division Microchip Ltd. Divyasree Chambers 505 Eskdale Road 1 Floor, Wing A (A3/A4) Winnersh Triangle No. 11, O’Shaugnessey Road Wokingham Bangalore, 560 025, India Berkshire, England RG41 5TU Tel: 91-80-2290061 Fax: 91-80-2290062 Tel: 44-118-921-5869 Fax: 44-118-921-5820 05/30/03 DS21732B-page 26  2003 Microchip Technology Inc.

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the MCP3221DM-PCTL have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

product

IC CAN I/O EXPND A/D 14SOIC

product

IC CAN CONTROLLER W/SPI 20-TSSOP

product

IC CAN CONTROLLER W/SPI 18SOIC

product

IC CAN CONTROLLER W/SPI 20TSSOP

product

IC COMP PUSHPULL 1.6V QUAD 14DIP

product

IC PGA 2CH R-R I/O 8SOIC