MCP1630 NiMH
Battery Charger Demo Board
User’s Guide
© 2006 Microchip Technology Inc. DS51505B
Note the following details of the code protection feature on Microchip devices:
• Microchip products meet the specification contained in their particular Microchip Data Sheet.
• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
• Microchip is willing to work with the customer who is concerned about the integrity of their code.
• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device Trademarks
applications and the like is provided only for your convenience
The Microchip name and logo, the Microchip logo, Accuron,
and may be superseded by updates. It is your responsibility to
dsPIC, KEELOQ, microID, MPLAB, PIC, PICmicro,
ensure that your application meets with your specifications.
PICSTART, PRO MATE, PowerSmart, rfPIC and SmartShunt
MICROCHIP MAKES NO REPRESENTATIONS OR
are registered trademarks of Microchip Technology
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
Incorporated in the U.S.A. and other countries.
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
AmpLab, FilterLab, Migratable Memory, MXDEV, MXLAB,
OTHERWISE, RELATED TO THE INFORMATION,
SEEVAL, SmartSensor and The Embedded Control Solutions
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
Company are registered trademarks of Microchip Technology
QUALITY, PERFORMANCE, MERCHANTABILITY OR
Incorporated in the U.S.A.
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
Analog-for-the-Digital Age, Application Maestro, dsPICDEM,
devices in life support and/or safety applications is entirely at
dsPICDEM.net, dsPICworks, ECAN, ECONOMONITOR,
the buyer’s risk, and the buyer agrees to defend, indemnify and
FanSense, FlexROM, fuzzyLAB, In-Circuit Serial
hold harmless Microchip from any and all damages, claims,
Programming, ICSP, ICEPIC, Linear Active Thermistor,
suits, or expenses resulting from such use. No licenses are
MPASM, MPLIB, MPLINK, MPSIM, PICkit, PICDEM,
conveyed, implicitly or otherwise, under any Microchip
PICDEM.net, PICLAB, PICtail, PowerCal, PowerInfo,
intellectual property rights.
PowerMate, PowerTool, REAL ICE, rfLAB, rfPICDEM, Select
Mode, Smart Serial, SmartTel, Total Endurance, UNI/O,
WiperLock and ZENA are trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2006, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona, Gresham, Oregon and Mountain View, California. The
Company’s quality system processes and procedures are for its
® ®
PICmicro 8-bit MCUs, KEELOQ code hopping devices, Serial
EEPROMs, microperipherals, nonvolatile memory and analog
products. In addition, Microchip’s quality system for the design and
manufacture of development systems is ISO 9001:2000 certified.
DS51505B-page ii © 2006 Microchip Technology Inc.
MCP1630 NiMH BATTERY CHARGER
DEMO BOARD USER’S GUIDE
Table of Contents
Preface ........................................................................................................................... 1
Chapter 1. Product Overview ....................................................................................... 5
1.1 Introduction ..................................................................................................... 5
1.2 What is the MCP1630 NiMH Battery Charger Demo Board? ......................... 6
1.3 What the MCP1630 NiMH Battery Charger Demo Board Kit Includes ........... 6
Chapter 2. Installation and Operation ......................................................................... 7
2.1 Introduction ..................................................................................................... 7
2.2 Features ......................................................................................................... 7
2.3 Getting Started ............................................................................................... 8
Appendix A. Schematic and Layouts ........................................................................ 11
A.1 Introduction .................................................................................................. 11
A.2 Board Schematic - Page 1 ......................................................................... 12
A.3 Board Schematic - Page 2 ......................................................................... 13
A.4 Board - Top Layer ...................................................................................... 14
A.5 Board - Bottom Layer ................................................................................. 15
A.6 Board - Mid-Layer 1 ................................................................................... 16
A.7 Board - Mid-Layer 2 ................................................................................... 17
Appendix B. Bill Of Materials (BOM) ......................................................................... 19
Appendix C. Evaluation Board Firmware .................................................................. 21
C.1 Device Firmware .......................................................................................... 21
Worldwide Sales and Service .................................................................................... 24
© 2006 Microchip Technology Inc. DS51505B-page iii
MCP1630 NiMH Battery Charger Demo Board User’s Guide
NOTES:
DS51505B-page iv © 2006 Microchip Technology Inc.
MCP1630 NiMH BATTERY CHARGER
DEMO BOARD USER’S GUIDE
Preface
NOTICE TO CUSTOMERS
All documentation becomes dated, and this manual is no exception. Microchip tools and
documentation are constantly evolving to meet customer needs, so some actual dialogs
and/or tool descriptions may differ from those in this document. Please refer to our web site
(www.microchip.com) to obtain the latest documentation available.
Documents are identified with a “DS” number. This number is located on the bottom of each
page, in front of the page number. The numbering convention for the DS number is
“DSXXXXXA”, where “XXXXX” is the document number and “A” is the revision level of the
document.
®
For the most up-to-date information on development tools, see the MPLAB IDE on-line help.
Select the Help menu, and then Topics to open a list of available on-line help files.
INTRODUCTION
This chapter contains general information that will be useful to know before using the
MCP1630 NiMH Battery Charger Demo Board. Items discussed in this chapter include:
• Document Layout
• Conventions Used in this Guide
• Recommended Reading
• The Microchip Web Site
• Customer Support
• Document Revision History
DOCUMENT LAYOUT
This document describes how to use the MCP1630 NiMH Battery Charger Demo
Board. The manual layout is as follows:
• Chapter 1. “Product Overview” – Important information about the MCP1630
NiMH Battery Charger Demo Board.
• Chapter 2. “Installation and Operation” – This chapter includes instructions on
how to get started, as well as a description of the MCP1630 NiMH Battery
Charger Demo Board.
• Appendix A. “Schematic and Layouts” – Shows the schematic and layout
diagrams for the MCP1630 NiMH Battery Charger Demo Board.
• Appendix B. “Bill Of Materials (BOM)” – Lists the parts used to build the
MCP1630 NiMH Battery Charger Demo Board.
• Appendix C. “Evaluation Board Firmware” – Provides information about the
application firmware and where the source code can be found.
© 2006 Microchip Technology Inc. DS51505B-page 1
MCP1630 NiMH Battery Charger Demo Board User’s Guide
CONVENTIONS USED IN THIS GUIDE
This manual uses the following documentation conventions:
DOCUMENTATION CONVENTIONS
Description Represents Examples
Arial font:
®
Italic characters Referenced books MPLAB IDE User’s Guide
Emphasized text ...is the only compiler...
Initial caps A window the Output window
A dialog the Settings dialog
A menu selection select Enable Programmer
Quotes A field name in a window or “Save project before build”
dialog
Underlined, italic text with A menu path File>Save
right angle bracket
Bold characters A dialog button Click OK
A tab Click the Power tab
N‘Rnnnn A number in verilog format, 4‘b0010, 2‘hF1
where N is the total number of
digits, R is the radix and n is a
digit.
Text in angle brackets < > A key on the keyboard Press ,
Courier New font:
Plain Courier New Sample source code #define START
Filenames autoexec.bat
File paths c:\mcc18\h
Keywords _asm, _endasm, static
Command-line options -Opa+, -Opa-
Bit values 0, 1
Constants 0xFF, ‘A’
Italic Courier New A variable argument file.o, where file can be
any valid filename
Square brackets [ ] Optional arguments mcc18 [options] file
[options]
Curly brackets and pipe Choice of mutually exclusive errorlevel {0|1}
character: { | } arguments; an OR selection
Ellipses... Replaces repeated text var_name [,
var_name...]
Represents code supplied by void main (void)
user { ...
}
RECOMMENDED READING
This user's guide describes how to use the MCP1630 NiMH Battery Charger Demo
Board. The following Microchip documents are available and recommended as
supplemental reference resources.
MCP1630 Data Sheet, “High-Speed, Microcontroller-Adaptable, Pulse Width
Modulator” (DS21896)
This data sheet provides detailed information regarding the MCP1630 product family.
DS51505B-page 2 © 2006 Microchip Technology Inc.
Preface
THE MICROCHIP WEB SITE
Microchip provides online support via our web site at www.microchip.com. This web
site is used as a means to make files and information easily available to customers.
Accessible by using your favorite internet browser, the web site contains the following
information:
• Product Support – Data sheets and errata, application notes and sample
programs, design resources, user’s guides and hardware support documents,
latest software releases and archived software
• General Technical Support – Frequently Asked Questions (FAQs), technical
support requests, online discussion groups, Microchip consultant program
member listing
• Business of Microchip – Product selector and ordering guides, latest Microchip
press releases, listing of seminars and events, listings of Microchip sales offices,
distributors and factory representatives
CUSTOMER SUPPORT
Users of Microchip products can receive assistance through several channels:
• Distributor or Representative
• Local Sales Office
• Field Application Engineer (FAE)
• Technical Support
• Development Systems Information Line
Customers should contact their distributor, representative or field application engineer
for support. Local sales offices are also available to help customers. A listing of sales
offices and locations is included in the back of this document.
Technical support is available through the web site at: http://support.microchip.com
DOCUMENT REVISION HISTORY
Revision B (March 2006)
• Updated Bill of Materials (BOM) to show RoHS-compliant part numbers.
Revision A (September 2004)
• Initial Release of this Document.
© 2006 Microchip Technology Inc. DS51505B-page 3
MCP1630 NiMH Battery Charger Demo Board User’s Guide
NOTES:
DS51505B-page 4 © 2006 Microchip Technology Inc.
MCP1630 NiMH BATTERY CHARGER
DEMO BOARD USER’S GUIDE
Chapter 1. Product Overview
1.1 INTRODUCTION
The MCP1630 NiMH Battery Charger Demo Board is used to evaluate the Microchip
MCP1630 used in a SEPIC power-converter application. The evaluation board is a
complete stand-alone 4-cell NiMH battery charger that utilizes an 8V to 15V input
capable of charging 4 NiMH batteries in series.
MCP1630 NiMH Battery Charger and Fuel Gauge Application Diagram
C
C
+V
BATT
+8V to +15V Input Voltage SEPIC Converter
4 NiMH Cells
+5V Bias
Cout
C
IN
MCP1630
Linear
1:1
Regulator
V
IN
I
BATT
N-Channel
COMP
V
EXT
MOSFET
FB
OSC IN
CS
I
SW
V
GND
REF
+V
BATT
+5V Bias
+
–
3V
0V
PIC16LF818
PWM OUT
V
DD
MCP1700
–
3.0V V
DD
A/D
SOT-23
+
1/2 MCP6042
V
DD
+
2
I C™ Interface
A/D
I/O
–
A/D
To System
1/2 MCP6042
TC1047A
FIGURE 1-1: NiMH Charger Block Diagram.
© 2006 Microchip Technology Inc. DS51505B-page 5
MCP1630 NiMH Battery Charger Demo Board User’s Guide
1.2 WHAT IS THE MCP1630 NIMH BATTERY CHARGER DEMO BOARD?
The MCP1630 NiMH Battery Charger Demo Board is a complete stand-alone constant
current battery charger and simple fuel gauge for four NiMH series batteries. This
®
board utilizes Microchip’s MCP1630 (high-speed PIC MCU PWM MSOP-8),
MCP1700T (LDO Regulator SOT-23), MCP6042T (Op Amp MSOP-8), PIC16LF818
(MCU Flash SSOP-20), TC54 (Voltage Detector SOT-23A) and TC1047A (Temp-Volt
Converter SOT-23B). The input voltage range for the demo board is 8V to 15V. The
output is capable of charging four NiMH batteries with up to 1.6V per cell at a fast
charge rate of 500 mA contant current.
Input terminals are provided to apply an intput voltage to the charger. Output terminals
are also provided as a way to connect the external NiMH batteries or a simulated
battery load.
1.3 WHAT THE MCP1630 NIMH BATTERY CHARGER DEMO BOARD KIT
INCLUDES
This MCP1630 NiMH Battery Charger Demo Board Kit includes:
• The MCP1630 NiMH Battery Charger Demo Board
• MCP1630 NiMH Battery Charger Demo Board User’s Guide (DS51505)
• MCP1630 Data Sheet, “High-Speed, Microcontroller-Adaptable, Pulse Width
Modulator” (DS21896)
DS51505B-page 6 © 2006 Microchip Technology Inc.
MCP1630 NiMH BATTERY CHARGER
DEMO BOARD USER’S GUIDE
Chapter 2. Installation and Operation
2.1 INTRODUCTION
The MCP1630 NiMH Battery Charger Demo Board demonstrates Microchip’s
MCP1630 high-speed Pulse Width Modulator (PWM) used in a smart battery charger
application. The MCP1630 is a high-speed, microcontroller-adaptable PWM that, when
used in conjunction with a microcontroller, will control the power system duty cycle to
provide output voltage or current regulation. The PIC16LF818 microcontroller can be
used to regulate output voltage or current, switching frequency and maximum duty
cycle. The MCP1630 generates pulse-by-pulse duty cycle, provides fast overcurrent
protection and utilizes variable external inputs. External signals include the input
oscillator and the reference voltage. The power train signals include the current sense
and the feedback voltage; the output signal is a square-wave pulse. The power train
used for the MCP1630 NiMH Battery Charger Demo Board is a Single-Ended Primary
Inductive Converter (SEPIC).
2.2 FEATURES
The MCP1630 NiMH Battery Charger Demo Board has the following features:
• Programmed charge currents:
- Fast Charge = 500 mA
- Trickle Charge = 50 mA
- Top-Off Charge = 25 mA
• Overvoltage protection (battery removed)
• Overcharge protection to prevent the battery from becoming dangerously
overcharged
• Overdischarge protection to prevent the battery from being damaged
• Overcurrent protection in the event of a shorted battery
• Battery reversal protection
• Input short circuit protection
• Fast charge termination if the battery or ambient temperature is too high
• Soft-start capability by holding the reference voltage low during power-up
• The MCP1630 NiMH Battery Charger Demo Board terminates charge by detect-
ing a predefined change in voltage with respect to time, a specified temperature or
specified elapsed time
• A simple fuel gauge that has a dual MCP6042 amplifier, a 1-channel sense
voltage and a 1-channel sense current
• The MCP1630 NiMH Battery Charger Demo Board has the flexibility to optimize
the charging algorithm for new battery technology and add proprietary features by
coding the microcontroller
• Ability to adapt to environmental effects, such as ambient temperature
• Uses a very low standby current of 29μA
© 2006 Microchip Technology Inc. DS51505B-page 7
MCP1630 NiMH Battery Charger Demo Board User’s Guide
2.3 GETTING STARTED
The MCP1630 NiMH Battery Charger Demo Board is fully assembled and tested for
charging four 1,000 mA/hour NiMH batteries in series from 3.2V to 6V in accordance
with the recommended charge profile for NiMH batteries. This board requires the use
of an external input voltage source (+8V to +15V) and external load (battery or simu-
lated battery load). It is recommended that four NiMH cells connected in series to act
as a load or the recommended simulated load be used.
2.3.1 Power Input and Output Connections
2.3.1.1 POWERING THE MCP1630 NiMH BATTERY CHARGER DEMO BOARD.
1. Apply the input voltage to the surface mount test points provided. The input
voltage source should be limited to the 0V to +15V range. For normal operation,
the input voltage should be between +8V and +15V. However, the input voltage
must not exceed +15V maximum. The source current necessary to regulate the
output voltage to 6.4V at 500 mA should be a minimum of approximately 800 mA.
2. Connect the positive side of the input source (+) to test point TP2. Connect the
negative (or return side) (–) of the input source to the GND test point TP3. TP2
is located just above TP3 in the upper-left corner of the board.
2.3.1.2 APPLYING THE LOAD TO THE MCP1630 NiMH BATTERY CHARGER
DEMO BOARD.
1. To apply a load to the MCP1630 NiMH Battery Charger Demo Board, the positive
side of the load (+) should be connected to test point TP1. The negative side of
the load (–) should be connected to test point TP4. Care should be taken when
using electronic or ground-referenced loads, and never connect TP4 to ground.
The battery current sense is referenced in the return leg, so connecting TP4 to
ground will short out the current sense. The typical charge current is 50 mA while
the battery is in the Trickle Charge mode or the battery voltage is below 0.8V/cell.
The current is typically 500 mA when the battery is in the Fast Charge mode and
typically 25 mA when the battery is in the Top-off Charge mode. The charge
current is automatically regulated by the MCP1630.
2. The code will prevent the board from entering the 500 mA Fast Charge mode if
the battery terminal voltage is less than 3.2V (0.8V / Cell). During power up, the
board will always trickle charge first, so using a purely resistive load will not work
for trickle and fast charge currents. The best way to evaluate the charger is to
use four series NiMH batteries or the recommended simulated battery load.
TP1
+
+
+
1,000μF
10Ω
Charger
4V Lab Supply
10V Al
5 Watt
–
–
–
TP4
FIGURE 2-1: Simulated Battery Load.
DS51505B-page 8 © 2006 Microchip Technology Inc.
Installation and Operation
2.3.1.3 STATUS LEDS
The MCP1630 NiMH Battery Charger Demo Board has two LEDs. D is a red LED that
1
is used to indicate when input power is available. When the +12V input is connected,
D will be illuminated. The other LED (D ) has two LEDs built into a SOT-23 package.
1 9
These can be off, red, green or both on (amber). To conserve energy, D is never
9
illuminated when there is no input power. If both LEDs are off, that is an indication there
is no power supplied to the board input.
Under normal power-up conditions, the charger will begin with a 50 mA trickle charge.
The microcontroller will then check the status of the batteries to ensure that they are
present, their temperature is within range and the series voltage is within specified
charging limits. For visual LED charge status, a dual-color SOT-23 LED is used (D ).
9
-D Status Indication Normal Charge Modes:
9
Normal Charge Mode
Red LED Green LED
Board Status
Initial Trickle Charge (50 mA) ON (Solid) OFF
Fast Charge (500 mA) ON (Solid) ON (Solid)
Final Trickle Charge (50 mA) OFF ON (Solid)
Top Off Charge (25 mA) OFF ON (Solid)
Charge Complete (0 mA) OFF ON (Blinking, 1 sec)
Initial Trickle Charge (50 mA) ON (Solid) OFF
-D Status Indication for Fault Modes:
9
Fault Mode Board Status Red LED Green LED
Overvoltage Initial ON (Blinking) OFF
(Restart Initiated)
Overvoltage ON (Blinking Faster) OFF
(Persistent, Latched-off after 9
attempts)
Overcurrent ON Blinking OFF
With no input connected and 4 NiMH batteries used as a load, the MCP1630 NiMH
Battery Charger Demo Board will consume approximately 29μA from the battery.
A temperature sensor is provided for charge termination. The sensor (U2) is located on
the back of the printed circuit board. To utilize this feature, batteries should be in
physical contact with the temperature sensor.
Programming:
- J1 can be used as a Flash programming port to modify the code for proto-
type applications. The pinout of J1 matches the required pinout for the
®
MPLAB ICD 2 programmer.
© 2006 Microchip Technology Inc. DS51505B-page 9
MCP1630 NiMH Battery Charger Demo Board User’s Guide
NOTES:
DS51505B-page 10 © 2006 Microchip Technology Inc.
MCP1630 NiMH BATTERY CHARGER
DEMO BOARD USER’S GUIDE
Appendix A. Schematic and Layouts
A.1 INTRODUCTION
This appendix contains the schematics and layouts for the MCP1630 NiMH Battery
Charger Demo Board. The diagrams included in this appendix include:
• Board Schematic
• Board - Top Layer
• Board - Bottom Layer
• Board - Mid-Layer 1
• Board - Mid-Layer 2
© 2006 Microchip Technology Inc. DS51505B-page 11
MCP1630 NiMH Battery Charger Demo Board User’s Guide
A.2 BOARD SCHEMATIC - PAGE 1
DS51505B-page 12 © 2006 Microchip Technology Inc.
(BACK)
(BACK)
Schematic and Layouts
A.3 BOARD SCHEMATIC - PAGE 2
© 2006 Microchip Technology Inc. DS51505B-page 13
(BACK)
S
G
(BACK)
D
(BACK)
2
(BACK)
(BACK)
(BACK)
(BACK)
3
1
MCP1630 NiMH Battery Charger Demo Board User’s Guide
A.4 BOARD - TOP LAYER
TOP LAYER
DS51505B-page 14 © 2006 Microchip Technology Inc.
Schematic and Layouts
A.5 BOARD - BOTTOM LAYER
© 2006 Microchip Technology Inc. DS51505B-page 15
MCP1630 NiMH Battery Charger Demo Board User’s Guide
A.6 BOARD - MID-LAYER 1
DS51505B-page 16 © 2006 Microchip Technology Inc.
Schematic and Layouts
A.7 BOARD - MID-LAYER 2
© 2006 Microchip Technology Inc. DS51505B-page 17
MID2
MCP1630 NiMH Battery Charger Demo Board User’s Guide
NOTES:
DS51505B-page 18 © 2006 Microchip Technology Inc.
MCP1630 NiMH BATTERY CHARGER
DEMO BOARD USER’S GUIDE
Appendix B. Bill Of Materials (BOM)
TABLE B-1: BILL OF MATERIALS (BOM)
Qty Reference Description Manufacturer Part Number
6 C1, C2, C4, “Do Not Populate” DNP0603 — —
C10, C13, C22
®
8 C3, C5, C6, CAP .10UF 10V CERAMIC X7R 0603 Kemet Electronics C0603C104K8RACTU
C7, C14, C15,
C17, C24
®
2 C8, C9 CAP CERAMIC 4.7UF 16V X5R 0805 Panasonic - ECG ECJ-2FB1C475K
1 C11 CAP CERAMIC 470PF 50V NP0 0603 Panasonic - ECG ECJ-1VC1H471J
®
3 C12, C19, C20 CAP CER 1.0UF 10V 10% X5R 0603 Murata Electronics GRM188R61A105KA61
North America D
2 C16,C21 CAP CERAMIC 22PF 50V NP0 0603 Kemet Electronics C0603C220J5GACTU
1 C18 CAP 10000PF 50V CERAMIC X7R 0603 Kemet Electronics C0603C103K5RACTU
1 C23 CAP CERAMIC 1UF 25V X5R 0805 Panasonic - ECG ECJ-2FB1E105K
®
1 D1 LED 660NM SUPER RED DIFF 0603SMD Lumex Opto/ SML-LX0603SRW-TR
Components Inc.
1 D4 DIODE SWITCH 75V 200MW SOT-323 Diodes Inc. BAS16W-7
1 D5 DIODE SCHOTTKY 25V 1.0A MINI-2P Panasonic - SSG MA2YD2300L
2D6, D8 “Do Not Populate” SOT-323 — —
®
1 D7 DIODE SWITCH DUAL CC 50V SOT-23 ON Semiconductor BAV74LT1
1 D9 LED DUAL RED/GREEN CLEAR SOT-23 Lumex Opto/ SML-LX15IGC-RP-TR
Components Inc.
® ®
1 J1 CONN MOD JACK 6-6 R/A PCB 50AU AMP /Tyco 5520470-3
Electronics
1 J2 CONN HEADER VERT 3POS .100 TIN AMP/Tyco Electronics 640454-3
1 J3 CONN HEADER VERT 2POS .100 TIN AMP/Tyco Electronics 640454-2
1 Q1 HEX/MOS N-CH 20V 4.2A SOT-23 International Rectifier IRLML2502TR
1 Q3 MOSFET N-CH 30V 1.7A 3-SSOT Fairchild NDS355AN
®
Semiconductor
2 R1, R2 RES 200 OHM 1/16W 1% 0603 SMD Panasonic - ECG ERJ-3EKF2000V
9 R3, R5, R6 RES 47.5K OHM 1/16W 1% 0603 SMD Panasonic - ECG ERJ-3EKF4752V
R7, R8, R9
R10, R11, R12
1 R4 RES 2.49K OHM 1/16W 1% 0603 SMD Panasonic - ECG ERJ-3EKF2491V
5 R13, R14, R29, “Do Not Populate” 0603 - -
R30, R37
1 R15 RES 20K OHM 1/16W .1% 0603 SMD Panasonic - ECG ERA-3YEB203V
1 R16 RES ZERO OHM 1/10W 5% 0603 SMD Panasonic - ECG ERJ-3GEY0R00V
2 R17, R34 RES 301K OHM 1/16W 1% 0603 SMD Panasonic - ECG ERJ-3EKF3013V
3 R18, R35, R36 RES 30.1K OHM 1/16W 1% 0603 SMD Panasonic - ECG ERJ-3EKF3012V
3 R19, R20, R27 RES 1.00K OHM 1/16W 1% 0603 SMD Panasonic - ECG ERJ-3EKF1001V
1 R21 RES .39 OHM 1/4W 1% 1206 SMD Panasonic - ECG ERJ-8RQFR39V
© 2006 Microchip Technology Inc. DS51505B-page 19
MCP1630 NiMH Battery Charger Demo Board User’s Guide
TABLE B-1: BILL OF MATERIALS (BOM) (CONTINUED)
Qty Reference Description Manufacturer Part Number
1 R22 RES .15 OHM 1/8W 5% 0805 SMD Panasonic - ECG ERJ-6RSJR15V
1 R23 RES 4.3K OHM 1/16W .5% 0603 SMD Susumu Co Ltd RR0816P-432-D
1 R24 RES 243K OHM 1/16W 1% 0603 SMD Panasonic - ECG ERJ-3EKF2433V
1 R25 RES 150K OHM 1/16W 1% 0603 SMD Panasonic - ECG ERJ-3EKF1503V
1 R26 RES 16.0K OHM 1/16W .5% 0603 SMD Susumu Co Ltd RR0816P-163-D
1 R28 RES 10.0K OHM 1/16W 1% 0603 SMD Panasonic - ECG ERJ-3EKF1002V
1 R31 RES 107K OHM 1/16W 1% 0603 SMD Panasonic - ECG ERJ-3EKF1073V
2 R32, R33 RES 61.9K OHM 1/16W 1% 0603 SMD Panasonic - ECG ERJ-3EKF6192V
1 R38 RES 249 OHM 1/16W 1% 0603 SMD Panasonic - ECG ERJ-3EKF2490V
3 S1, S2, S3 SWITCH TACT 6MM 260GF SMT E-Switch, Inc. TL3301NF260QG
®
1 T1 8th-PAK SMT Dual Inductor BH Electronics L11-1016
®
4 TP1, TP2, TP3, PC TEST POINT COMPACT SMT Keystone Electronics 5016
TP4
1 U1 IC MCU FLASH 1KX14 EEPROM Microchip Technology, PIC16LF818-I/SS
20-SSOP Inc.
1 U2 IC TEMP-VOLT CONV PREC SOT-23B Microchip Technology, TC1047AVNBTR
Inc.
1 U3 High-Speed PIC PWM MSOP8 Microchip Technology, MCP1630-E/MS
Inc.
1 U4 IC OPAMP 1UA 1.4V DUAL R-R 8MSOP Microchip Technology, MCP6042T-I/MS
Inc.
1 U5 IC VREG MINI 5V 50MA SOT-23 Zetex Inc. ZMR500FTA
1 U6 IC COMPARATOR R-R OUT SC-70-5 National LMV7219M7
®
Semiconductor
1 U7 IC LDO REG 250MA 3.0V SOT-23 Microchip Technology, MCP1700T-3002E/TT
Inc.
1 U8 IC VOLT DETECTOR 2.9V SOT23A Microchip Technology, TC54VC2902ECB713
Inc.
DS51505B-page 20 © 2006 Microchip Technology Inc.
MCP1630 NiMH BATTERY CHARGER
DEMO BOARD USER’S GUIDE
Appendix C. Evaluation Board Firmware
C.1 DEVICE FIRMWARE
For the latest version of the MCP1630 NiMH Battery Charger Demo Board User’s
Guide firmware, visit the Microchip web site at www.microchip.com.
Power-Up
Initialize:
Ports, Clocks, A/D,
PWM, IIC, and
Interrupts
Yes
No No
Is Input Is Battery
Sleep Mode
Present? > 3.2V ?
Yes
Trickle Charge:
No Yes
Turn-on RED LED, Is Input
Start PWM, Soft-start Present?
C/20 Rate
No
Is Input
Present?
Yes No
No
Is Battery Timer
> 3.2V ? Expired?
Yes Yes
Yes
In Over- Hiccup Restart:
voltage? Stop PWM
No
Fast Charge:
No
Turn-on GREEN
Persistent?
LED, C/2 Rate
Yes
No
Is Input
Present?
Yes
Yes
In Over-
voltage?
No No
No
Full Timer
Charge? Expired?
Yes Yes
A B C D E
FIGURE C-1: Firmware Flowcharge - Page 1.
© 2006 Microchip Technology Inc. DS51505B-page 21
Evaluation Board Firmware
A B C D E
Top-off Charge:
Turn-off RED LED,
Fault:
C/20 Rate Followed Flash RED LED
BSy C/40 Rate
No Yes
Is Input
Is Input
Present? Present?
Yes No
Yes
In Over-
voltage?
No
Yes
Recharge?
No
No
Timer
Expired?
Yes
Charge Complete:
Flash GREEN LED,
C/40 Rate
No
Is Input
Present?
Yes
Yes
Recharge?
No
No
Timer
Expired?
Yes
FIGURE C-2: Firmware Flowchart - Page 2.
© 2006 Microchip Technology Inc. DS51505B-page 22
Evaluation Board Firmware
NOTES:
© 2006 Microchip Technology Inc. DS51505B-page 23
WORLDWIDE SALES AND SERVICE
AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE
Corporate Office Australia - Sydney
India - Bangalore Austria - Wels
2355 West Chandler Blvd. Tel: 61-2-9868-6733
Tel: 91-80-4182-8400
Tel: 43-7242-2244-399
Chandler, AZ 85224-6199 Fax: 61-2-9868-6755
Fax: 91-80-4182-8422
Fax: 43-7242-2244-393
Tel: 480-792-7200
China - Beijing
Denmark - Copenhagen
India - New Delhi
Fax: 480-792-7277
Tel: 86-10-8528-2100
Tel: 45-4450-2828
Tel: 91-11-5160-8631
Technical Support:
Fax: 86-10-8528-2104
Fax: 45-4485-2829
Fax: 91-11-5160-8632
http://support.microchip.com
China - Chengdu
France - Paris
India - Pune
Web Address:
Tel: 86-28-8676-6200 Tel: 33-1-69-53-63-20
Tel: 91-20-2566-1512
www.microchip.com
Fax: 86-28-8676-6599 Fax: 33-1-69-30-90-79
Fax: 91-20-2566-1513
Atlanta
China - Fuzhou Germany - Munich
Japan - Yokohama
Alpharetta, GA
Tel: 49-89-627-144-0
Tel: 86-591-8750-3506
Tel: 81-45-471- 6166
Tel: 770-640-0034
Fax: 49-89-627-144-44
Fax: 86-591-8750-3521
Fax: 81-45-471-6122
Fax: 770-640-0307
Italy - Milan
China - Hong Kong SAR
Korea - Gumi
Boston
Tel: 39-0331-742611
Tel: 852-2401-1200
Tel: 82-54-473-4301
Westborough, MA
Fax: 39-0331-466781
Fax: 852-2401-3431
Fax: 82-54-473-4302
Tel: 774-760-0087
Netherlands - Drunen
Fax: 774-760-0088 China - Qingdao
Korea - Seoul
Tel: 31-416-690399
Tel: 86-532-8502-7355
Tel: 82-2-554-7200
Chicago
Fax: 31-416-690340
Fax: 86-532-8502-7205
Fax: 82-2-558-5932 or
Itasca, IL
82-2-558-5934 Spain - Madrid
Tel: 630-285-0071
China - Shanghai
Tel: 34-91-708-08-90
Fax: 630-285-0075 Tel: 86-21-5407-5533
Malaysia - Penang
Fax: 34-91-708-08-91
Fax: 86-21-5407-5066
Tel: 60-4-646-8870
Dallas
UK - Wokingham
Addison, TX Fax: 60-4-646-5086
China - Shenyang
Tel: 44-118-921-5869
Tel: 972-818-7423
Tel: 86-24-2334-2829
Philippines - Manila
Fax: 44-118-921-5820
Fax: 972-818-2924
Fax: 86-24-2334-2393
Tel: 63-2-634-9065
Detroit Fax: 63-2-634-9069
China - Shenzhen
Farmington Hills, MI
Tel: 86-755-8203-2660
Singapore
Tel: 248-538-2250
Fax: 86-755-8203-1760
Tel: 65-6334-8870
Fax: 248-538-2260
Fax: 65-6334-8850
China - Shunde
Kokomo
Tel: 86-757-2839-5507
Taiwan - Hsin Chu
Kokomo, IN
Fax: 86-757-2839-5571
Tel: 886-3-572-9526
Tel: 765-864-8360
Fax: 886-3-572-6459
China - Wuhan
Fax: 765-864-8387
Tel: 86-27-5980-5300
Taiwan - Kaohsiung
Los Angeles
Fax: 86-27-5980-5118 Tel: 886-7-536-4818
Mission Viejo, CA
Fax: 886-7-536-4803
China - Xian
Tel: 949-462-9523
Tel: 86-29-8833-7250 Taiwan - Taipei
Fax: 949-462-9608
Tel: 886-2-2500-6610
Fax: 86-29-8833-7256
San Jose
Fax: 886-2-2508-0102
Mountain View, CA
Thailand - Bangkok
Tel: 650-215-1444
Tel: 66-2-694-1351
Fax: 650-961-0286
Fax: 66-2-694-1350
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
02/16/06
DS51505B-page 24 © 2006 Microchip Technology Inc.
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods