Manufacturers
MICRO/SYS SBC1625
Description
Micro/Sys SBC1625 CPU Board with Intel IXP420 or IXP425 XScale Processor, PC/104, Dual Ethernet
Part Number
SBC1625
Price
Request Quote
Manufacturer
MICRO/SYS
Lead Time
Request Quote
Category
COMPONENTS
Specifications
10/100BASE-T Ethernet Ports
Two 10/100 Ethernet ports. Auto MDIX allows automatic switching of twisted pair input and output. Standard RJ45 connectors.
COM1-COM4 Serial Ports
Four async serial ports. 16C550-compatible. RTS and CTS modem controls. RS232 on all channels. COM2 RS485 half duplex.
CompactFlash Interface
Supports Type I or II CompactFlash. Not hot-swappable.
Digital I/O
24 TTL bi-directional signals. 82C55 digital I/O chip. Direction programmable in two groups of eight bits and two groups of four bits. Eight LEDs on port B. Octal DIP switch on port A. 470-ohm current-limiting resistors on all lines.
DK1625 Development Kit
Free with first SBC1625 purchase. Breakout cable to COM1-COM4. Download cable and utilities. Documentation, schematics, sample software.
Environmental
Operating range 0° to +70°C. ET-version operating range -40° to +85°C. -40° to +85°C storage. 5%-95% relative humidity, non-condensing.
External Connections
40-pin header for COM1-COM4, USB, JTAG. Two 8-pin modular RJ45 jacks for Ethernet. 26-pin header for digital I/O. 2-pin locking header for reset. 3-pin removable terminal strip for power input.
JTAG Interface
Debug unit has hardware break points and 256-entry trace history buffer. IEEE 1149.1 JTAG compatible.
Mechanical
PC/104 standard. 3.55” (plus I/O region) x 3.775” x .6”. Installed CompactFlash card extends past edge of board opposite the PC/104 connector. If installed, Ethernet connector on top side has height of .453”. Components on the bottom side have a maximum height of .134”.
On-board Memory
64-128MB Synchronous DRAM. 16-64MB of linear flash for bootloader, operating system, and application.
PC/104 Interface
Non-stackthrough PC/104 connectors. Standard mounting holes. 8-bit and 16-bit PC/104 module support. I/O accesses supported, memory accesses not supported. Stackthrough option available(SBCOPT16ST).
Power Requirements
+5v ±5% at 385mA typical, 770mA max. +12v required only if used by PC/104 modules.
Processor Core Section
Intel IXP425 or IXP420. 266 or 533 MHz clock rate. StrongARM v5TE instruction set.
Real Time Clock
RTC with on-board battery. Driver software in BIOS.
USB Interface
USB v1.1. Device or function controller only. USB controller does not operate as a host.
Watchdog Timer
Program must refresh watchdog timer periodically, or system will be reset. Enabled through software.
Features
- 128MB SDRAM, 64MB Flash
- 24 bits of digital I/O
- 266 to 533MHz clock speed
- CompactFlash connector
- Dual 10/100BASE-T Ethernet
- Extended temperature available
- Four serial ports
- Low-power ARM processor
Datasheet
Extracted Text
XScale PC/104 Computer with Dual Ethernet SBC1625 Features 99999 Low-power ARM processor 99999 266 to 533MHz clock speed 99999 Dual 10/100BASE-T Ethernet 99999 128MB SDRAM, 64MB Flash 99999 CompactFlash connector 99999 Four serial ports 99999 24 bits of digital I/O 99999 Extended temperature available The SBC1625 packs a fast Intel XScale RISC card. Immediately and easily, an advanced engine processor with lots of memory into a is available for software development. PC/104-sized board. The efficient, industry- standard ARM architecture allows the With up to 64MB of onboard linear flash, and SBC1625 to draw little power at its full 533MHz 128MB of SDRAM, many complex operating clock speed. This reduces power supply and systems, such as Linux and Windows CE can be cooling requirements. Onboard I/O includes run. However, if additional storage capacity is 24 TTL digital I/O lines, four serial ports, required, the CompactFlash connector allows dual 10/100BASE-T Ethernet, USB, and hundreds of megabytes of removable storage. CompactFlash. And, if additional capabilities are needed, In its stackthrough version, the SBC1625 is an PC/104 expansion allows a wide variety of I/O ideal computer to plug into a custom OEM I/O cards to be stacked on the SBC1625 Software Support Compatible Hardware Mounting/Packaging Linux PC/104 expansion cards Standoffs, STDOFF01 Windows CE [Items above in Section 4] [Items above in Section 5] VxWorks® RS232/RS485 devices Custom RTOS Custom C, compilers [Items above in Section 6] Micro/sys 3730 Park Place, Montrose, CA 91020 (818)244-4600 Fax (818)244-4246 email: info@embeddedsys.com Dual P DIO Ethernet C / EEPROM XScale (ARM) 1 CPU 0 RTC 4 64MB 128MB Compact I/ SDRAM Flash Flash O USB JTAG COM1-COM4 Technical Details: The SBC1625 core is an Intel IXP425 or IXP420 application code space. Some of the flash can be allocated as a read/write flash drive. XScale processor running at 266 or 533 MHz. The Intel XScale processor core is clocked at a rate of 266MHz to 533MHz. This variation of the If a larger program or data storage space is industry-standard ARM architecture is a RISC required, or if removability is needed, the processor that is designed for fast Ethernet CompactFlash interface can provide hundreds of megabytes of storage. communication and has a dual Ethernet controller built in. Four serial ports allow communication with many The IXP42x allows compatibility with 32-bit different devices. COM1 through COM4 are operating systems. The IXP42x also integrates 16C550-compatible UARTs (with transmit and receive FIFOs). These serial ports have RS-232 many peripherals. Dual USB ports, an interrupt transceivers, and have RTS and CTS modem controller, dual 16C550 UARTs, a watchdog timer, and an SDRAM controller are all present. control lines. Additionally, COM2 is configurable for half-duplex RS-485 communication with The memory subsystem on the SBC1625 allows jumperable termination resistors. many programs to be run without any external The PC/104 connector provides support for both storage. 128 Mbytes of synchronous DRAM (SDRAM) is more than sufficient for many complex 8-bit and 16-bit I/O expansion boards. The default programs and operating systems. configuration is non-stackthrough connectors, allowing the SBC1625 to be the bottom card in a stack. The stackthrough option (SBCOPT16ST) The 64-Mbyte Flash memory contains the bootloader, operating system, and user Micro/sys 3730 Park Place, Montrose, CA 91020 (818)244-4600 Fax (818)244-4246 email: info@embeddedsys.com allows the SBC1625 to be plugged into a custom- Processor Core Section: designed OEM I/O board as an automation Intel IXP425 or IXP420 component. 266 or 533 MHz clock rate StrongARM v5TE instruction set For true 32-bit application development, the SBC1625 supports a number of alternatives. On-board Memory: 32-bit operating systems such as Linux, 64-128MB Synchronous DRAM Windows CE, and VxWorks® can be booted on 16-64MB of linear flash for bootloader, the SBC1625. All have full tool suites available, operating system, and application including compilers and debuggers. Watchdog Timer: For pre-configured sets of options, Micro/sys can Program must refresh watchdog timer provide OEMs with a single part number for periodically, or system will be reset ordering. In addition, custom versions of the Enabled through software SBC1625 are available. Please call Micro/sys Technical Sales for details. COM1-COM4 Serial Ports: Four async serial ports 16C550-compatible Specifications: RTS and CTS modem controls RS232 on all channels Mechanical: COM2 RS485 half duplex PC/104 standard 3.55” (plus I/O region) x 3.775” x .6” 10/100BASE-T Ethernet Ports: Installed CompactFlash card extends past Two 10/100 Ethernet ports edge of board opposite the PC/104 connector Auto MDIX allows automatic switching of If installed, Ethernet connector on top side twisted pair input and output has height of .453”. Components on the Standard RJ45 connectors bottom side have a maximum height of .134”. Real Time Clock: Power Requirements: RTC with on-board battery +5v ±5% at 385mA typical, 770mA max Driver software in BIOS +12v required only if used by PC/104 modules Digital I/O: 24 TTL bi-directional signals Environmental: 82C55 digital I/O chip Operating range 0° to +70°C Direction programmable in two groups of ET-version operating range -40° to +85°C eight bits and two groups of four bits -40° to +85°C storage Eight LEDs on port B 5%-95% relative humidity, non-condensing Octal DIP switch on port A 470-ohm current-limiting resistors on all lines Power Connector Pin Signal 1+5V 2 +12V 3GND Micro/sys 3730 Park Place, Montrose, CA 91020 (818)244-4600 Fax (818)244-4246 email: info@embeddedsys.com PC/104 Interface: Digital I/O Connector Non-stackthrough PC/104 connectors Pin Signal Signal Pin 1DIOA0 DIOA1 2 Standard mounting holes 3DIOA2 DIOA3 4 8-bit and 16-bit PC/104 module support 5DIOA4 DIOA5 6 I/O accesses supported, memory ac- 7DIOA6 DIOA7 8 cesses not supported 9DIOB0 DIOB1 10 Stackthrough option available 11 DIOB2 DIOB3 12 (SBCOPT16ST) 13 DIOB4 DIOB5 14 15 DIOB6 DIOB7 16 17 DIOC0 DIOC1 18 CompactFlash Interface: 19 DIOC2 DIOC3 20 Supports Type I or II CompactFlash 21 DIOC4 DIOC5 22 Not hot-swappable 23 DIOC6 DIOC7 24 25 GND GND 26 DK1625 Development Kit: Free with first SBC1625 purchase JTAG Interface: Breakout cable to COM1-COM4 Debug unit has hardware break points and Download cable and utilities 256-entry trace history buffer Documentation, schematics, sample IEEE 1149.1 JTAG compatible software USB Interface: External Connections: USB v1.1 40-pin header for COM1-COM4, USB, Device or function controller only. USB JTAG controller does not operate as a host Two 8-pin modular RJ45 jacks for Ethernet 26-pin header for digital I/O Main I/O Connector 2-pin locking header for reset Pin Signal Signal Pin 3-pin removable terminal strip for power 1 RX COM3 RTS COM3 2 3 TX COM3 CTS COM3 4 input 5--6 7 GND RX COM4 8 Ordering Information: 9 RTS COM4 TX COM4 10 11 CTS COM4 - 12 13 - GND 14 Single Board Computer: 15 RX COM1 RTS COM1 16 SBC1625 IXP420 CPU, 266MHz, 17 TX COM1 CTS COM1 18 64MB RAM, 16MB Flash, 19--20 dual Ethernet 21 GND RX COM2 22 SBC1625-533 IXP420 CPU, 533MHz, 23 RTS COM2 TX COM2 24 64MB RAM, 16MB Flash, 25 CTS COM2 - 26 dual Ethernet 27 - GND 28 SBC1625-ET IXP420 CPU, 266MHz, 29 RS485- RS485+ 30 31 GND USB- 32 64MB RAM, 16MB Flash, 33 USB+ TRST_N 34 dual Ethernet, -40° to 35 TDO TMS 36 +85°C operating 37 +3.3V TCK 38 temperature 39 TDI RST_N 40 Micro/sys 3730 Park Place, Montrose, CA 91020 (818)244-4600 Fax (818)244-4246 email: info@embeddedsys.com SBC1625-533-ET IXP425 CPU, 533MHz, 64MB RAM, 16MB Flash, dual Ethernet, -40° to +85°C operating temperature DK1625 No charge development kit, available with first order only SDK-Linux-1625 Linux Development kit (must also purchase 1625OPT50) SDK-WinCE-1625 WinCE Development kit (must also purchase 1625OPT55) 1625OPT3 128MB SDRAM 1625OPT5 32MB Flash 1625OPT6 64MB Flash 1625OPT50 Linux in flash 1625OPT55 WinCE in flash Related Products: CA4107 Breakout cable to four DB9 COM port connectors BA4107 Breakout assembly to four DB9 COM port connectors, RS485, USB, JTAG CA5051 26-pin to 26-pin ribbon cable for digital I/O BA0026 Breakout assembly to 26- position terminal strip. Includes CA5051 and TB50326 SBCOPT16ST Stackthrough PC/104 CF-FL128 128MB CompactFlash Card CF-FL256 256MB CompactFlash Card CF-FL512 512MB CompactFlash Card Cables nominally 15”, other lengths available VxWorks trademark Wind River Micro/sys 3730 Park Place, Montrose, CA 91020 (818)244-4600 Fax (818)244-4246 email: info@embeddedsys.com
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the SBC1625 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Related Products
Mirco/sys Extractor Tool - Extractor Tool for PC/104 Boards
Request a Quote
The quote request has been received
Close
Facing challenges or have inquiries? Feel free to contact us!
Call Us +1-469-283-2440
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods