MICREL SY10EL34ZCTR
Description
IC CLK GEN /2/4/6 5V/3.3V 16SOIC
Part Number
SY10EL34ZCTR
Price
Request Quote
Manufacturer
MICREL
Lead Time
Request Quote
Category
PRODUCTS - S
Datasheet
Extracted Text
ClockWorks™ 5V/3.3V ÷2, ÷4, ÷8 CLOCK SY10EL34/L SY100EL34/L GENERATION CHIP FINAL FEATURES DESCRIPTION 3.3V and 5V power supply options The SY10/100EL34/L are low skew ÷2, ÷4, ÷8 clock generation chips designed explicitly for low skew clock 50ps output-to-output skew generation applications. The internal dividers are Synchronous enable/disable synchronous to each other, therefore, the common output Master Reset for synchronization edges are all precisely aligned. The devices can be driven Internal 75KΩ input pull-down resistors by either a differential or single-ended ECL or, if positive power supplies are used, PECL input signal. In addition, Available in 16-pin SOIC package by using the VBB output, a sinusoidal source can be AC- coupled into the device. If a single-ended input is to be used, the VBB output should be connected to the CLK input and bypassed to ground via a 0.01μF capacitor. PIN CONFIGURATION/BLOCK DIAGRAM The VBB output is designed to act as the switching reference for the input of the EL34/L under single-ended input conditions. As a result, this pin can only source/ sink up to 0.5mA of current. VCC 16 Q0 1 The common enable (EN) is synchronous so that the Q ÷2 internal dividers will only be enabled/disabled when the 2 15 EN Q0 R internal clock is already in the LOW state. This avoids Q D any chance of generating a runt clock pulse on the VCC 3 14 NC internal clock when the device is enabled/disabled as R can happen with an asynchronous control. An internal 4 Q1 13 CLK runt pulse could lead to losing synchronization between Q ÷4 the internal divider stages. The internal enable flip-flop is 5 12 CLK Q1 R clocked on the falling edge of the divider stages. The internal enable flip-flop is clocked on the falling edge of VCC 6 11 VBB the input clock, therefore, all associated specification limits are referenced to the negative edge of the clock Q2 7 10 MR Q input. ÷8 9 Upon start-up, the internal flip-flops will attain a random 8 R VEE Q2 state; the master reset (MR) input allows for the synchronization of the internal dividers, as well as for multiple EL34/Ls in a system. SOIC TOP VIEW PIN NAMES Pin Function CLK Differential Clock Inputs EN Synchronous Enable MR Master Reset VBB Reference Output Q0 Differential ÷2 Outputs Q1 Differential ÷4 Outputs Q2 Differential ÷8 Outputs Rev.: F Amendment: /0 Issue Date: August, 1998 1 ClockWorks™ SY10EL34/L Micrel SY100EL34/L TRUTH TABLE CLK EN MR Function Z L L Divide ZZ H L Hold Q0–2 X X H Reset Q0–2 NOTE: Z = LOW-to-HIGH transition ZZ = HIGH-to-LOW transition (1) DC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = GND TA = –40°CTA = 0°CTA = +25°CTA = +85°C Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit IEE Power Supply 10EL — — 49 — — 49 — — 49 — — 49 mA Current 100EL — — 49 — — 49 — — 49 — — 54 VBB Output Reference 10EL –1.43 — –1.30 –1.38 — –1.27 –1.35 — –1.25 –1.31 — –1.19 V Voltage 100EL –1.38 — –1.26 –1.38 — –1.26 –1.38 — –1.26 –1.38 — –1.26 IIH Input High Current — — 150 — — 150 — — 150 — — 150 μA NOTE: 1. Parametric values specified at: 5 volt Power Supply Range 100EL34 Series: -4.2V to -5.5V. 10EL34 Series -4.75V to -5.5V. 3 volt Power Supply Range 10/100EL34L Series: -3.0V to -3.8V. (1) AC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = GND TA = –40°CTA = 0°CTA = +25°CTA = +85°C Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit tPLH Propagation Delay to ps tPHL Output CLK 960 1100 1200 960 1100 1200 960 1100 1200 960 1100 1200 MR 650 800 1010 650 800 1010 650 800 1010 650 800 1010 (2) tskew Within-Device Skew — — 50 — — 50 — — 50 — — 50 ps tS Set-up Time EN 400 — — 400 — — 400 — — 400 — — ps tH Hold Time EN 200 — — 200 — — 200 — — 200 — — ps (3) VPP Minimum Input Swing 250 — — 250 — — 250 — — 250 — — mV (4) VCMR Common Mode Range –1.3 — –0.4 –1.4 — –0.4 –1.4 — –0.4 –1.4 — –0.4 V tr Output Rise/Fall Times 275 400 525 275 400 525 275 400 525 275 400 525 ps tf Q (20% – 80%) NOTES: 1. Parametric values specified at: 5 volt Power Supply Range 100EL34 Series: -4.2V to -5.5V. 10EL34 Series -4.75V to -5.5V. 3 volt Power Supply Range 10/100EL34L Series: -3.0V to -3.8V. 2. Skew is measured between outputs under identical transitions. 3. Minimum input swing for which AC parameters are guaranteed. The device will function reliably with differential inputs down to 100mV. 4. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPP min. and 1V. The lower end of the CMR range varies 1:1 with VEE. The numbers in the spec table assume a nominal VEE = –3.3V. Note for PECL operation, the VCMR (min) will be fixed at 3.3V – IVCMR (min)I. 2 ClockWorks™ SY10EL34/L Micrel SY100EL34/L TIMING DIAGRAM Internal Clock Internal Clock Disabled Enabled CLK Q0 Q1 Q2 EN The EN signal will freeze the internal clocks to the flip-flops on the first falling edge of CLK after its assertion. The internal dividers will maintain their state during the internal clock freeze and will return to clocking once the internal clocks are unfrozen. The outputs will transition to their next states in the same manner, time and relationship as they would have had the EN signal not been asserted. PRODUCT ORDERING CODE 5V 3.3V Ordering Package Operating VEE Range Ordering Package Operating VEE Range Code Type Range (V) Code Type Range (V) SY10EL34LZC Z16-2 Commercial -3.0 to -3.8 SY10EL34ZC Z16-2 Commercial -4.75 to -5.5 SY10EL34LZCTR Z16-2 Commercial -3.0 to -3.8 SY10EL34ZCTR Z16-2 Commercial -4.75 to -5.5 SY100EL34LZC Z16-2 Commercial -3.0 to -3.8 SY100EL34ZC Z16-2 Commercial -4.2 to -5.5 SY100EL34LZCTR Z16-2 Commercial -3.0 to -3.8 SY100EL34ZCTR Z16-2 Commercial -4.2 to -5.5 3 ClockWorks™ SY10EL34/L Micrel SY100EL34/L 16 LEAD SOIC .150" WIDE (Z16-2) Rev. 02 MICREL-SYNERGY 3250 SCOTT BOULEVARD SANTA CLARA CA 95054 USA TEL + 1 (408) 980-9191 FAX + 1 (408) 914-7878 WEB http://www.micrel.com This information is believed to be accurate and reliable, however no responsibility is assumed by Micrel for its use nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent right of Micrel Inc. © 2000 Micrel Incorporated 4
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the SY10EL34ZCTR have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Manufacturers




What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods