Touch Probe Line T25 T36 TL25 NEW HIGH PERFORMANCE MIDA TOUCH PROBES FOR CNC LATHES, MACHINING CENTERS AND FLAGGING ON GRINDING MACHINES New high performance MIDA touch probes for tool check ing, Modular system part inspection and part set-up applications on CNC lathes, New MIDA probes are compatible with the wide range machining centers and grinding machines. Reduced scrap, of MIDA modular components, enabling systems to be shorter cycle and set-up times and im proved prod uct quality conŢ gured to suit all applications. are just some of the beneŢ ts to be gained. Infra-red and radio trans mis sion systems allow the probe Supported by a full range of Software Packages, MIDA of fers to be stored in the ma chine ATC (Automatic Tool Changer), a complete solution for every measurement application. whilst hard-wired sys tems permit economic use on ma chines without ATC, and for table mounted ap pli ca tions. Outstanding performance Extension bars and adap tors enable access into difŢ cult to New MIDA probes offer exceptional improved repeatability reach fea tures. (2σ < 0,5 µm) to meet the most demanding measurement ap pli ca tions. Available versions New MIDA probes are available in a variety of styles to suit Rugged and reliable speciŢ c requirements such as very compact dimensions with New MIDA probes have been developed to withstand the T25 probes, very long styli for deep bore inspection, using harshest operating conditions, having been designed and T36, low trigger force for soft part inspection with TL25. tested to work over many millions cycles. Insensitive to rapid Any probe is available with front rubber gasket (“G” version) machine acceleration and vibration, new MIDA probes offer or shielded to provide additional external protection against excellent protection against high-pres sure coolant and hot chips and swarf on lathes (“S” version). chips. TOUCH PROBE LINE 1 Accessories Tool & Process Toolsetting Arms Software Laser Transmission T Touch P ouch Pr robes obes Monitoring Systems T To ou uch P ch Pr robes obes Transmission Laser Software Toolsetting Arms Tool & Process Accessories Systems Monitoring Probes with rubber gasket (“G” version) Technical SpeciŢ cation 4 40 6.6 T25G TL25G (0.16”) (1.57”) (0.26”) Unidirectional repeatability (2σ) 0,5 µm 0,5 µm at speed up to 600 mm/min 2 N 0,9 N Trigger force on X, Y plane (200 gf) (90 gf) 12 N 5,5 N Trigger force in Z direction (1200 gf) (550 gf) Overtravel on X, Y plane 11,2 mm 11,2 mm Overtravel in Z direction 4 mm 4 mm Probe Code 25.5 T25G 3415335200 (1.00”) IP67 IP67 Watertightness (IEC standards) TL25G 3424306040 Above characteristics refer to a 35 mm stylus Probe Code Technical SpeciŢ cation 55 T36G 3415340200 (2.16”) T36G Unidirectional repeatability (2σ) 0,5 µm at speed up to 600 mm/min 2,6 N Trigger force on X, Y plane (260 gf) 12 N Trigger force in Z direction (1200 gf) Overtravel on X, Y plane 14,4 mm 4.2 Overtravel in Z direction 4,2 mm 34.5 (0.16”) IP67 Watertightness (IEC standards) (1.36”) Above characteristics refer to a 35 mm stylus Probes with metal shield (“S” version) Technical SpeciŢ cation 4 40 6.6 T25S TL25S (0.16”) (1.57”) (0.26”) Unidirectional repeatability (2σ) 0,5 µm 0,5 µm at speed up to 600 mm/min 2 N 0,9 N Trigger force on X, Y plane (200 gf) (90 gf) 12 N 5,5 N Trigger force in Z direction (1200 gf) (550 gf) Overtravel on X, Y plane 11,2 mm 11,2 mm 25.5 Probe Code Overtravel in Z direction 4 mm 4 mm T25S 3415335201 (1.00”) Watertightness (IEC standards) IP67 IP67 TL25S 3424306041 Above characteristics refer to a 35 mm stylus Probe Code Technical SpeciŢ cation 55 T36S 3415340201 (2.16”) T36S Unidirectional repeatability (2σ) 0,5 µm at speed up to 600 mm/min 2,6 N Trigger force on X, Y plane (260 gf) 12 N Trigger force in Z direction (1200 gf) Overtravel on X, Y plane 14,4 mm 4.2 Overtravel in Z direction 4,2 mm 34.5 (0.16”) IP67 Watertightness (IEC standards) (1.36”) Above characteristics refer to a 35 mm stylus For a full list of address locations, please consult the Marposs ofŢ cial website D6C01900G0 - Edition 09/2005 - Specifications are subject to modifications © Copyright 2003-2005 MARPOSS S.p.A. (Italy) - All rights reserved. MARPOSS, and Marposs product names/signs mentioned or shown herein are registered trademarks or trademarks of Marposs in the United States and other countries. The rights, if any, of third parties on trademarks or registered trademarks mentioned in the present publication are acknowledged to the respective owners. Marposs has an integrated system to manage the Company quality, the environment and safety, attested by ISO 9001, ISO 14001 and OHSAS 18001 certiŢ cations. Marposs has further been qualiŢ ed EAQF 94 and has obtained the Q1-Award. www.marposs.com 2 TOUCH PROBE LINE -12° +12° -12° +12° -12° +12° -12° +12° M16x1 M16x1 35.8 25 35.8 25 ( 1.41”) ( 1.41”) ( 0.98”) ( 0.98”)