MODEL: W5FV 1 – 5 V DC (Input resistance 1 MΩ min.) Terminal Block Dual Output Signal Conditioners W5-UNIT -10 – +10 V DC (Input resistance 1 MΩ min.) -5 – +5 V DC (Input resistance 1 MΩ min.) SIGNAL TRANSMITTER (field-configurable) OUTPUT 1 – Field-selectable Functions & Features Current • Converts a DC input into two isolated outputs 4 – 20 mA DC (Load resistance 550 Ω max.) • Two independent output ranges 0 – 20 mA DC (Load resistance 550 Ω max.) • DIP switch configurable input & output range Voltage • Four-way isolation (input to output 1 to output2 to power) 0 – 10 V DC (Load resistance 1000 Ω min.) • High-density mounting 0 – 5 V DC (Load resistance 500 Ω min.) • CE marking for 24 V power 1 – 5 V DC (Load resistance 500 Ω min.) -10 – +10 V DC (Load resistance 8000 Ω min.) Typical Applications -5 – +5 V DC (Load resistance 4000 Ω min.) • Isolation between control room and field instrumentation 45 (1.77) [1] OUTPUT 2 Y: None Current A: 4 – 20 mA DC (Load resistance 550 Ω max.) 97 (3.82) B: 2 – 10 mA DC (Load resistance 1100 Ω max.) C: 1 – 5 mA DC (Load resistance 2200 Ω max.) D: 0 – 20 mA DC (Load resistance 550 Ω max.) 41 (1.61) mm (inch) E: 0 – 16 mA DC (Load resistance 685 Ω max.) F: 0 – 10 mA DC (Load resistance 1100 Ω max.) G: 0 – 1 mA DC (Load resistance 11 kΩ max.) MODEL: W5FV-[1]-[2][3] Z: Specify current (See OUTPUT SPECIFICATIONS) Voltage 1: 0 – 10 mV DC (Load resistance 10 kΩ min.) ORDERING INFORMATION 2: 0 – 100 mV DC (Load resistance 100 kΩ min.) Specify a code from below for each [1] through [3]. 3: 0 – 1 V DC (Load resistance 100 Ω min.) When only one output is needed, select code Y for Output 2, 4: 0 – 10 V DC (Load resistance 1000 Ω min.) [1]. 5: 0 – 5 V DC (Load resistance 500 Ω min.) Orders will be shipped at default factory settings for Input (1 6: 1 – 5 V DC (Load resistance 500 Ω min.) – 5V) and Output 1 (4 – 20mA ). 4W: -10 – +10 V DC (Load resistance 2000 Ω min.) • Code number: W5FV-[1]-[2][3] 5W: -5 – +5 V DC (Load resistance 1000 Ω min.) (e.g. W5FV-6-P/Q) 0: Specify voltage (See OUTPUT SPECIFICATIONS) Specify variables. • Special 2nd output range (For codes Z & 0) • Specify the specification for option code /Q [2] POWER INPUT (e.g. /C01) AC Power M: 85 – 264 V AC (Operational voltage range 85 – 264 V, 47 –66 Hz) INPUT – Field-selectable (CE not available) Current DC Power 4 – 20 mA DC (Input resistance 250 Ω) R: 24 V DC 0 – 20 mA DC (Input resistance 250 Ω) (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) 0 – 10 mA DC (Input resistance 250 Ω) R2: 11 – 27 V DC Voltage (Operational voltage range 11 – 27 V, ripple 10 %p-p max.) 0 – 60 mV DC (Input resistance 1 MΩ min.) (CE not available) 0 – 100 mV DC (Input resistance 1 MΩ min.) P: 110 V DC 0 – 1 V DC (Input resistance 1 MΩ min.) (Operational voltage range 85 – 150 V, ripple 10 %p-p max.) 0 – 10 V DC (Input resistance 1 MΩ min.) (CE not available) 0 – 5 V DC (Input resistance 1 MΩ min.) http://www.m-system.co.jp/ W5FV SPECIFICATIONS ES-8515 Rev.6 Page 1/4 MODEL: W5FV Mounting: DIN rail [3] OPTIONS Weight: 130 g (0.29 lbs) blank: none /Q: With options (specify the specification) PERFORMANCE in percentage of span Accuracy: ±0.1 % SPECIFICATIONS OF OPTION: Q Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) COATING (For the detail, refer to M-System's web site.) Response time: ≤ 0.5 sec. (0 – 90 %) /C01: Silicone coating Line voltage effect: ±0.1 % over voltage range /C02: Polyurethane coating Insulation resistance: ≥ 100 MΩ with 500 V DC /C03: Rubber coating Dielectric strength: 2000 V AC @1 minute (input to output 1 or output 2 to GENERAL SPECIFICATIONS power to ground) Construction: Terminal block 1000 V AC @1 minute (output 1 to output 2) Connection Input: M3.5 screw terminals (torque 0.8 N·m) STANDARDS & APPROVALS Output & power: M3 screw terminals (torque 0.8 N·m) CE conformity: Screw terminal: Nickel-plated steel EMC Directive (2004/108/EC) Housing material: Flame-resistant resin (black) EMI EN 61000-6-4: 2007 Isolation: Input to output 1 to output 2 to power EMS EN 61000-6-2: 2005 Overrange output: Approx. -10 to +120 % at 1 – 5 V Zero adjustment: -2 to +2 % (front) (±1 % with ±5V and ±10V input ranges) Span adjustment: 98 to 102 % (front) (99 to 101 % with ±5 V and ±10 V input ranges) INPUT SPECIFICATIONS ■ DC Current: Input resistor incorporated • DC Voltage Input resistance: 1 MΩ min. OUTPUT SPECIFICATIONS OUTPUT 2 ■ DC Current: 0 – 20 mA DC Minimum span: 1 mA Offset: Max. 1.5 times span Load resistance: Output drive 11 V max. ■ DC Voltage: -10 – +12 V DC Spans: Min. 5 mV, max. 20 V Offset: Max. 1.5 times span Load resistance: Output drive 10 mA max.; 5 mA for negative voltage output; at ≥ 0.5 V INSTALLATION Power Consumption •AC Power input: Approx. 4 VA at 100 V Approx. 5 VA at 200 V Approx. 6 VA at 264 V •DC power input: Approx. 3 W Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 0 to 90 %RH (non-condensing) http://www.m-system.co.jp/ W5FV SPECIFICATIONS ES-8515 Rev.6 Page 2/4 MODEL: W5FV EXTERNAL VIEW Input Range 1 2 3 4 5 6 7 8 DIP SW (SW1) 1 2 3 4 5 Output Range DIP SW (SW2) • Output 2* • Output 1 Span Adj. Span Adj. Zero Adj. Zero Adj. 6 7 8 9 10 11 *Not provided for single output type. INPUT RANGE(DIP SW) Input exceeding the maximum value of each input range may destroy the transmitter. Be sure to confirm the setting range before applying input signals. Input range setting accuracy: Approx. 1 %(≤ 2 % when both input and output ranges are modified.) SW1 INPUT RANGE 1 2 3 4 5 6 7 8 4 – 20mA DC n n n 0 – 20mA DC n n n 0 – 10mA DC n n n 0 – 60mV DC n 0 – 100mV DC n n 0 – 1V DC n n n 0 – 10V DC n n 0 – 5V DC n n 1 – 5V DC n n n -10 – +10V DC n n -5 – +5V DC n n n n = ON, Blank = OFF OUTPUT RANGE(DIP SW) Only Output 1 is field-configurable. Specify Output 2 range when ordering. Output range setting accuracy: Approx. 1 %(≤ 2 % when both input and output ranges are modified.) SW2 OUTPUT RANGE 1 2 3 4 5 6 7 8 4 – 20mA DC n n n n n n n 0 – 20mA DC n n 0 – 10V DC n n n n 0 – 5V DC n n n n n n 1 – 5V DC n n n -10 – +10V DC n n -5 – +5V DC n n n http://www.m-system.co.jp/ W5FV SPECIFICATIONS ES-8515 Rev.6 Page 3/4 ON MODEL: W5FV DIMENSIONS unit: mm (inch) 7.4 (.29) 5–M3.5 SCREW 1 2 3 4 5 DIN RAIL 35mm wide 6 (.24) 6 7 8 9 10 11 45 (1.77) 41 (1.61) [3.3 (.13)] 6–M3 SCREW • When mounting, no extra space is needed between units. SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM OUTPUT RANGE SELECTOR DIP SW Z S Isolation Low Drift Output + 4 6 + Amplifier Driver * INPUT OUTPUT 1 – 5 7 – INPUT RANGE Z S SELECTOR DIP SW 1 Output + 8 Driver 2 OUTPUT 2 – 9 3 10 U(+) POWER 11 V(–) *Input shunt resistor attached for current input. Remark 1: The section enclosed by broken line is only with 2nd output option. Remark 2: DO NOT connect to the terminals 1 – 2 – 3. Specifications are subject to change without notice. http://www.m-system.co.jp/ W5FV SPECIFICATIONS ES-8515 Rev.6 Page 4/4 3 (.12) 94 (3.70)