MODEL: M6SXF3 described range of the selected suffix code. Tension-Clamp Ultra-Slim Signal Conditioners M6S Series For changing between suffix codes, set the Input Range Selector on the side of unit before software adjustment.) HOLD FUNCTION MODULE (PC programmable) [2] OUTPUT Functions & Features Current • Maintenance-free tension clamp connection Z1: Range 0 – 20 mA DC • Track/Hold or Peak hold function’s selection available Voltage • 5.9-mm wide ultra-slim design with DC current signal V2: Range -10 – +10 V DC input V3: Range -5 – +5 V DC • Low profile allows the M6S module to be mounted in a 120 (Configurator software is used to change output over the -mm deep panel described range of the selected suffix code. • PC programmable For changing between suffix codes, set the Output Range • High-density mounting available Selector on the side of unit before software adjustment.) • Power and status indicator LEDs • CE approval POWER INPUT Typical Applications DC Power • Monitoring peak power consumption R: 24 V DC • Monitoring the highest or lowest temperature (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) • Capturing signals from a composite analyzer performing on each sample in turn FUNCTIONS PC Configurator Software is used to change function type. 5.9 (.23) • Track/Hold • Peak hold Peak hold Valley hold 94 (3.70) Peak-to-peak hold (Peak hold-Valley hold) Factory default setting Control/Hold: Track/Hold Control/Control Logic: Hold at open 102 (4.02) mm (inch) RELATED PRODUCTS • PC configurator software (model: M6CFG) Downloadable at M-System’s web site. MODEL: M6SXF3–[1][2]–R A dedicated cable is required to connect the module to the PC. Please refer to the internet software download site or the users manual for the PC configurator for applicable ORDERING INFORMATION cable types. • Code number: M6SXF3-[1][2]-R Specify a code from below for each [1] and [2]. (e.g. M6SXF3-Z1Z1-R) GENERAL SPECIFICATIONS • Input range (e.g. 4 – 20 mA DC) Connection • Output range (e.g. 4 – 20 mA DC) Input and output: Tension clamp Power input: Via the Installation Base (model: M6SBS) or Tension clamp [1] INPUT Applicable wire size: 0.2 to 2.5 mm2, stripped length 8 mm Current Housing material: Flame-resistant resin (black) Z1: Range 0 – 50 mA DC (Input resistance 24.9 Ω) Isolation: Input to output to power Voltage Overrange output: -2 – +102 % S1: Range -1000 – +1000 mV DC (Input resistance 1 MΩ min.) (Negative current output is not available.) S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.) Zero adjustment: -2 to +2% (PC programming) (Configurator software is used to change input over the http://www.m-system.co.jp/ M6SXF3 SPECIFICATIONS ES-7990 Rev.1 Page 1/4 MODEL: M6SXF3 Span adjustment: 98 to 102% (PC programming) Output range: -10 – +10 V DC Power LED: Green light turns on when the power is supplied. Conformance range: -10.4 – +10.4 V DC Status indicator LED: Orange LED; Flashing patterns Minimum span: 1 V indicate different operating status of the transmitter. Code V3 (narrow spans) Programming: Downloaded from PC; input type and range, Output range: -5 – +5 V DC output type and range, zero and span, function type, control Conformance range: -5.2 – +5.2 V DC input logic, user’s linearization table (max. 101 points, Minimum span: 0.5 V specified within -2 to +102% for both input and output), etc. Offset: Lower range can be any specific value within the For detailed information, refer to the users manual for the output range provided that the minimum span is PC configurator. maintained. Configurator connection: 2.5 dia. miniature jack; Load resistance: Output drive 1 mA max. RS-232C level (e.g. 1 – 5 V: 5000 Ω [5 V/1 mA]) If not specified, the output range is shown below. V2: 0 – 10 V DC INPUT SPECIFICATIONS V3: 1 – 5 V DC • DC Current: Input resistor incoporated (If not specified, the input range is 4 – 20 mA DC.) Input range: 0 – 50 mA DC INSTALLATION Minimum span: 2 mA Power consumption: Approx. 0.5 W Offset: Lower range can be any specific value within the Operating temperature: -20 to +55°C (-4 to +131°F) input range provided that the minimum span is maintained. Operating humidity: 30 to 90 %RH (non-condensing) • DC Voltage Mounting: Installation Base (model: M6SBS) or DIN rail Code S1 (narrow spans) Weight: 65 g (2.3 oz) Input range: -1000 – +1000 mV DC Minimum span: 100 mV PERFORMANCE in percentage of span Code S2 (wide spans) Overall accuracy: Input accuracy + output accuracy Input range: -10 – +10 V DC Inversely proportional to the span. Minimum span: 1 V See CALCULATION EXAMPLES OF OVERALL ACURACY. Offset: Lower range can be any specific value within the • Input accuracy: (% of max. input range) input range provided that the minimum span is maintained. -1000 – +1000 mV : ±0.01 % If not specified, the input range is shown below. -10 – +10 V : ±0.01 % S1: 0 – 100 mV DC 0 – 50 mA : ±0.02 % S2: 1 – 5 V DC • Output accuracy: ±0.04 % of max. output range • CONTROL Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. span Contact rating: 3 V @1 mA Response time: ≤ 0.5 sec. (0 – 90 %) Detection levels: Line voltage effect: ±0.1 % over voltage range ≤ 0.6 kΩ / 0.5 V at close Insulation resistance: ≥ 100 MΩ with 500 V DC ≥ 15 kΩ / 2.5 V at open Dielectric strength: 2000 V AC @1 minute (input to output to power to ground) OUTPUT SPECIFICATIONS • DC CURRENT CALCULATION EXAMPLES OF OVERALL ACCURACY Output range: 0 – 20 mA DC [Example] Input Type -10 – +10 V, Input Range 1 – 5 V, Conformance range: 0 – 20.4 mA DC Output Type -5 – +5 V, Output Range 1 – 5 V Minimum span: 1 mA • Input accuracy = Max. Input Range (20 V) / Span (4 V) × Offset: Lower range can be any specific value within the 0.01 % = 0.05 % output range provided that the minimum span is • Output accuracy = Max. Output Range (10 V) / Span (4 V) maintained. × 0.04 % = 0.1 % Load resistance: Output drive 11 V max. Accuracy= ±0.15 % (e.g. 4 – 20 mA: 550 Ω [11 V/20 mA]) If not specified, the output range is 4 – 20 mA DC. • DC VOLTAGE Code V2 (wide spans) http://www.m-system.co.jp/ M6SXF3 SPECIFICATIONS ES-7990 Rev.1 Page 2/4 MODEL: M6SXF3 STANDARDS & APPROVALS CE conformity: EMC Directive (2004/108/EC) EN 61000-6-4 (EMI) EN 61000-6-2 (EMS) EXTERNAL VIEW � FRONT VIEW (with the cover open) � SIDE VIEW Output Range Selectors 5 6 7 8 Power LED Status Indicator LED Configurator Jack Input Range Selectors 1 2 3 4 The DIP switch setting is required to select input and output types before setting a precise range using PC Configurator Software (model: M6CFG). Refer to the instruction manual for detailed procedures. DIMENSIONS unit: mm (inch) SCREWDRIVER * INSERTION ANGLE : approx. 35° WIRE INSERTION ANGLE TEST PROBE : approx.35° max. 2 (.08) dia. 5 6 7 8 DIN RAIL HOOK DIN RAIL 35mm wide 1 2 3 4 SCREWDRIVER [0.5 (.02)] INSERTION ANGLE : approx. 40° 5.9 (.23) 102 (4.02) • When mounting, no extra space is needed between units. *Use a minus screwdriver: tip width 3.8 mm max., tip thickness 0.5 to 0.6 mm http://www.m-system.co.jp/ M6SXF3 SPECIFICATIONS ES-7990 Rev.1 Page 3/4 94 (3.70) SW2 SW1 SW2 SW1 ON ON OFF OFF 1 2 1 2 3 4 5 6 7 8 MODEL: M6SXF3 SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM STATUS LED DIP SW Isolation Digital Output 5 + Computation Driver + 1 OUTPUT Low Drift INPUT 6 – 24.9ΩAmplifier POWER LED – 2 +3V + 7 3kΩ POWER 3 8 – CONTROL 4 JACK CONFIGURATOR POWER Specifications are subject to change without notice. http://www.m-system.co.jp/ M6SXF3 SPECIFICATIONS ES-7990 Rev.1 Page 4/4 CONNECTOR