MODEL: M6SXAT Tension-Clamp Ultra-Slim Signal Conditioners M6S Series OUTPUT Relay; SPDT or transfer contact THERMOCOUPLE ALARM (PC programmable) POWER INPUT Functions & Features DC Power • Maintenance-free tension clamp connection R: 24 V DC • 5.9-mm wide ultra-slim design (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) • Low profile allows the M6S module mounted in a 120-mm deep panel RELATED PRODUCTS • Provides a relay contact output at preset DC input levels • PC configurator software (model: M6CFG) • PC programmable Downloadable at M-System’s web site. • Linearization and upscale and downscale burnout A dedicated cable is required to connect the module to the protection PC. Please refer to the internet software download site or • High-density mounting the users manual for the PC configurator for applicable • Power and status indicator LEDs cable types. 5.9 (.23) GENERAL SPECIFICATIONS Connection Input and output: Tension clamp 94 Power input: Via the Installation Base (model: M6SBS) (3.70) or Tension clamp Applicable wire size: 0.2 to 2.5 mm2, stripped length 8 mm Housing material: Flame-resistant resin (black) 102 Isolation: Input to output to power (4.02) Burnout: Upscale standard; downscale or no burnout mm (inch) optional by programming In case of upscale standard, the alarm operates as if the input signal has exceeded over the range. MODEL: M6SXAT–[1]–R Linearization: Standard Cold Junction Compensation: CJC sensor incorporated Power LED: Green light turns on when the power is supplied. ORDERING INFORMATION Status indicator LED: Orange LED; Flashing patterns • Code number: M6SXAT-[1]-R indicate different operating status of the transmitter. Spacify a code from below for [1]. Alarm monitor LED: Red LED turns on when the alarm is (e.g. M6SXAT-2-R) tripped. • Temperature range (e.g. 0 – 1000°C) Programming: Downloaded from PC Input type and range [1] INPUT THERMOCOUPLE Input fine adjustments 1: (PR) User’s Thermocouple table 2: K (CA) Burnout (Upscale, downscale or no burnout) 3: E (CRC) Alarm setpoint (input %) 4: J (IC) Trip action (High or Low) 5: T (CC) Relay coil (energized or de-energized) 6: B (RH) Power ON delay time (0 to 999 sec.) 7: R Alarm ON delay time (0 to 999 sec.) 8: S Hysteresis (deadband) (input %) N: N Alarm test, and others 0: Specify (Please provide a emf table.) Configurator connection: 2.5 dia. miniature jack; (Configurator software is used to change the input type and RS-232C level precise range.) Factory default setting Alarm setpoint: 80 % http://www.m-system.co.jp/ M6SXAT SPECIFICATIONS ES-7992 Rev.1 Page 1/4 MODEL: M6SXAT Trip action: High PERFORMANCE in percentage of span Relay coil at alarm: Energized Setpoint accuracy (trip point accuracy): Power ON delay time: 5 sec. Accuracy in Table 1 + Cold junction compensation error Alarm ON delay time: 0 sec. Cold junction compensation error: Hysteresis (deadband) : 1.0 % ±3°C at 25 ±10°C Burnout: Upscale ±5.4°F at 77 ±18°F Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. span Response time: ≤ 0.5 sec. (0 – 100 % at 90 % setpoint) INPUT SPECIFICATIONS Burnout response time: ≤ 1 sec. Input resistance: 1 MΩ min. Line voltage effect: ±0.1 % over voltage range Burnout sensing: ≤ 0.1 μA Insulation resistance: ≥ 100 MΩ with 500 V DC Temperature range: See Table 1. Dielectric strength: 2000 V AC @1 minute (input to output If not specified, the input range is shown below. to power to ground) 1 PR: 0 – 1600°C 2 K: 0 – 1000°C 3 E: 0 – 500°C CALCULATION EXAMPLES OF SETPOINT ACCURACY 4 J: 0 – 500°C [Example] K thermocouple, 0 – 1000°C 5 T: 0 – 300°C Absolute value accuracy (Table 1): 0.25°C 6 B: 500 – 1600°C CJC error (3°C) added: 3.25°C 7 R: 500 – 1600°C Setpoint accuracy = 3.25°C / 1000°C × 100 = 0.33 % 8 S: 0 – 1600°C Table 1. N N: 0 – 1000°C C THERMOCOUPLE MIN. MAXIMUM CONFORMANCE ACCURACY OUTPUT SPECIFICATIONS SPAN RANGE RANGE (PR) 20 0 to 1760 0 to 1760 ±1.00 • RELAY OUTPUT K (CA) 20 -270 to +1370 -150 to +1370 ±0.25 Relay rating: E (CRC) 20 -270 to +1000 -170 to +1000 ±0.20 250 V AC @2 A (cos ø = 1) J (IC) 20 -210 to +1200 -180 to +1200 ±0.25 30 V DC @2 A (resistive load) T (CC) 20 -270 to +400 -170 to +400 ±0.25 Maximum switching voltage: 250 V AC or 125 V DC B (RH) 20 100 to 1820 400 to 1760 ±0.75 Maximum switching power: 500 VA or 60 W R 20 -50 to +1760 200 to 1760 ±0.50 Minimum load: 5 V DC @100 mA S 20 -50 to +1760 0 to 1760 ±0.50 Mechanical life: 5 × 106 cycles (rate 180/min.) N 20 -270 to +1300 -130 to +1300 ±0.30 F Alarm Trip Operation Terminal No. in parentheses THERMOCOUPLE MIN. MAXIMUM CONFORMANCE • Setting Example ACCURACY SPAN RANGE RANGE Hi alarm (coil energized at alarm) or Lo alarm (coil de-energized at alarm) (PR) 36 32 to 3200 32 to 3200 ±1.80 K (CA) 36 -454 to +2498 -238 to +2498 ±0.45 (3–2)ON Output E (CRC) 36 -454 to +1832 -274 to +1832 ±0.36 (3–4)ON J (IC) 36 -346 to +2192 -292 to +2192 ±0.45 Input T (CC) 36 -454 to +752 -274 to +752 ±0.45 (%) 0 50 � 100 36 212 to 3308 752 to 3200 ±1.35 B (RH) Setpoint R 36 -58 to +3200 392 to 3200 ±0.90 Trip operation in power failure: Terminals 3 – 4 turn ON. S 36 -58 to +3200 32 to 3200 ±0.90 N 36 -454 to +2372 -202 to +2372 ±0.54 INSTALLATION STANDARDS & APPROVALS Power consumption: Approx. 0.5 W CE conformity: Operating temperature: -20 to +55°C (-4 to +131°F) EMC Directive (2004/108/EC) Operating humidity: 30 to 90 %RH (non-condensing) EN 61000-6-4 (EMI) Mounting: Installation Base (model: M6SBS) or DIN rail EN 61000-6-2 (EMS) Weight: 65 g (2.3 oz) Low Voltage Directive (2006/95/EC) EN 61010-1 Overvoltage Category II http://www.m-system.co.jp/ M6SXAT SPECIFICATIONS ES-7992 Rev.1 Page 2/4 MODEL: M6SXAT Pollution Degree 2 Max. operating voltage 250 V (relay output circuit) Input or power to output: Reinforced insulation Input to power: Basic insulation EXTERNAL VIEW (With the cover open) Power LED Alarm Monitor LED Status Indicator LED Configurator Jack DIMENSIONS unit: mm (inch) SCREWDRIVER * INSERTION ANGLE : approx. 35° WIRE INSERTION ANGLE TEST PROBE : approx.35° max. 2 (.08) dia. 5 6 7 8 DIN RAIL HOOK DIN RAIL 35mm wide 1 2 3 4 SCREWDRIVER [0.5 (.02)] INSERTION ANGLE : approx. 40° 5.9 (.23) 102 (4.02) • When mounting, no extra space is needed between units. *Use a minus screwdriver: tip width 3.8 mm max., tip thickness 0.5 to 0.6 mm http://www.m-system.co.jp/ M6SXAT SPECIFICATIONS ES-7992 Rev.1 Page 3/4 94 (3.70) MODEL: M6SXAT SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM STATUS ALARM CJC LED MONITOR LED SENSOR comp. leadwire + 4 NC T/C Digital + Ry 5 Computation Low Drift 2 NO OUTPUT Amplifier - 6 3 COM – POWER LED 1 + 7 POWER CONFIGURATOR JACK – 8 POWER n Relay Protection • AC Powered • DC Powered Inductive Inductive Load (Coil) Load (Coil) LOAD LOAD Diode, Varistor or Varistor or CR Circuit CR Circuit Specifications are subject to change without notice. http://www.m-system.co.jp/ M6SXAT SPECIFICATIONS ES-7992 Rev.1 Page 4/4 CONNECTOR