MODEL: M6SXAS Tension-Clamp Ultra-Slim Signal Conditioners M6S Series POWER INPUT DC Power R: 24 V DC DC ALARM (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) (PC programmable) Functions & Features • Maintenance-free tension clamp connection RELATED PRODUCTS • 5.9-mm wide ultra-slim design • PC configurator software (model: M6CFG) • Low profile allows the M6S module mounted in a 120-mm Downloadable at M-System’s web site. deep panel A dedicated cable is required to connect the module to the • Provides a relay contact output at preset DC input levels PC. Please refer to the internet software download site or • PC programmable the users manual for the PC configurator for applicable • High-density mounting cable types. • Power and status indicator LEDs GENERAL SPECIFICATIONS 5.9 (.23) Connection Input and output: Tension clamp Power input: Via the Installation Base (model: M6SBS) or Tension clamp 94 (3.70) Applicable wire size: 0.2 to 2.5 mm2, stripped length 8 mm Housing material: Flame-resistant resin (black) Isolation: Input to output to power Power LED: Green light turns on when the power is supplied. 102 (4.02) Status indicator LED: Orange LED; Flashing patterns mm (inch) indicate different operating status of the transmitter. Alarm monitor LED: Red LED turns on when the alarm is tripped. Programming: Downloaded from PC MODEL: M6SXAS–[1]–R Input type and range Input fine adjustments ORDERING INFORMATION Alarm setpoint (input %) • Code number: M6SXAS-[1]-R Trip action (High or Low) Specify a code from below for [1]. Relay coil (energized or de-energized) (e.g. M6SXAS-Z1-R) Power ON delay time (0 to 999 sec.) • Input range (e.g. 4 – 20 mA DC) Alarm ON delay time (0 to 999 sec.) Hysteresis (deadband) (input %) Alarm test, and others [1] INPUT For detailed information, refer to the users manual for the Current PC configurator. Z1: Range 0 – 50 mA DC (Input resistance 24.9 Ω) Configurator connection: 2.5 dia. miniature jack; Voltage RS-232C level S1: Range -1000 – +1000 mV DC (Input resistance 1 MΩ min.) Factory default setting S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.) Alarm setpoint: 80 % (Configurator software is used to change input over the Trip action: High described range of the selected suffix code. Relay coil at alarm: Energized For changing between suffix codes, set the Input Range Power ON delay time: 5 sec. Selector on the side of unit before software adjustment.) Alarm ON delay time: 0 sec. Hysteresis (deadband) : 1.0 % OUTPUT Relay; SPDT or transfer contact INPUT SPECIFICATIONS • DC Current: Input resistor incoporated (If not specified, the input range is 4 – 20 mA DC.) http://www.m-system.co.jp/ M6SXAS SPECIFICATIONS ES-7978 Rev.1 Page 1/4 MODEL: M6SXAS Input range: 0 – 50 mA DC Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. span Minimum span: 2 mA Response time: ≤ 0.2 sec. (0 – 100 % at 90 % setpoint) Offset: Lower range can be any specific value within the Line voltage effect: ±0.1 % over voltage range input range provided that the minimum span is maintained. Insulation resistance: ≥ 100 MΩ with 500 V DC • DC Voltage Dielectric strength: 2000 V AC @1 minute (input to output Code S1 (narrow spans) to power to ground) Input range: -1000 – +1000 mV DC Minimum span: 100 mV STANDARDS & APPROVALS Code S2 (wide spans) CE conformity: Input range: -10 – +10 V DC EMC Directive (2004/108/EC) Minimum span: 1 V EN 61000-6-4 (EMI) Offset: Lower range can be any specific value within the EN 61000-6-2 (EMS) input range provided that the minimum span is maintained. Low Voltage Directive (2006/95/EC) If not specified, the input range is shown below. EN 61010-1 S1: 0 – 100 mV DC Overvoltage Category II S2: 1 – 5 V DC Pollution Degree 2 Max. operating voltage 250 V (relay output circuit) OUTPUT SPECIFICATIONS Input or power to output: Reinforced insulation • RELAY OUTPUT Input to power: Basic insulation Relay rating: 250 V AC @2 A (cos ø = 1) 30 V DC @2 A (resistive load) Maximum switching voltage: 250 V AC or 125 V DC Maximum switching power: 500 VA or 60 W Minimum load: 5 V DC @100 mA Mechanical life: 5 × 106 cycles (rate 180/min.) Alarm Trip Operation Terminal No. in parentheses • Setting Example Hi alarm (coil energized at alarm) or Lo alarm (coil de-energized at alarm) (3–2)ON Output (3–4)ON Input (%) 0 50 � 100 Setpoint Trip operation in power failure: Terminals 3 – 4 turn ON. INSTALLATION Power consumption: Approx. 0.5 W Operating temperature: -20 to +55°C (-4 to +131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Installation Base (model: M6SBS) or DIN rail Weight: 65 g (2.3 oz) PERFORMANCE in percentage of span Setpoint accuracy (trip point accuracy) : ±0.05 % Setpoint accuracy is inversely proportional to the input span. [Example] Input type 0 – 50 mA, Input range 4 – 20 mA Max. Input Range (50 mA) / Span (16 mA) × 0.05 % = ±0.16 % http://www.m-system.co.jp/ M6SXAS SPECIFICATIONS ES-7978 Rev.1 Page 2/4 MODEL: M6SXAS EXTERNAL VIEW � FRONT VIEW (with the cover open) � SIDE VIEW 5 6 7 8 Power LED Input Selector Alarm Monitor LED I v Status Indicator LED Configurator Jack 1 2 3 4 The DIP switch setting is required to select input types before setting a precise input range using PC Configurator Software (model: M6CFG). Refer to the instruction manual for detailed procedures. DIMENSIONS unit: mm (inch) SCREWDRIVER * INSERTION ANGLE : approx. 35° WIRE INSERTION ANGLE TEST PROBE : approx.35° max. 2 (.08) dia. 5 6 7 8 DIN RAIL HOOK DIN RAIL 35mm wide 1 2 3 4 SCREWDRIVER [0.5 (.02)] INSERTION ANGLE : approx. 40° 5.9 (.23) 102 (4.02) • When mounting, no extra space is needed between units. *Use a minus screwdriver: tip width 3.8 mm max., tip thickness 0.5 to 0.6 mm http://www.m-system.co.jp/ M6SXAS SPECIFICATIONS ES-7978 Rev.1 Page 3/4 94 (3.70) SW1 MODEL: M6SXAS SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM STATUS ALARM LED MONITOR LED INPUT N.C. SELECTOR 4 Digital + Ry 5 Computation N.O. Low Drift 2 OUTPUT INPUT 24.9Ω Amplifier COM 3 – 6 POWER LED 1 7 + POWER CONFIGURATOR JACK 8 – POWER � Relay Protection • AC Powered • DC Powered Inductive Inductive Load (Coil) Load (Coil) LOAD LOAD Diode, Varistor or Varistor or CR Circuit CR Circuit Specifications are subject to change without notice. http://www.m-system.co.jp/ M6SXAS SPECIFICATIONS ES-7978 Rev.1 Page 4/4 CONNECTOR