MODEL: M6SCTC 260: 0 – 60 A AC Tension-Clamp Ultra-Slim Signal Conditioners M6S Series 275: 0 – 75 A AC 2100: 0 – 100 A AC CT TRANSMITTER 2125: 0 – 125 A AC (clamp-on current sensor) 2150: 0 – 150 A AC Functions & Features 2175: 0 – 175 A AC • Maintenance-free tension clamp connection 2200: 0 – 200 A AC • Converts AC current signal into a low-ripple standard 2225: 0 – 225 A AC process signal suitable to be handled for computer inputs 2250: 0 – 250 A AC • 5.9-mm wide ultra-slim design 2300: 0 – 300 A AC • Low profile allows the M6S module mounted in a 120-mm 2350: 0 – 350 A AC deep panel 2400: 0 – 400 A AC • High-density mounting 2500: 0 – 500 A AC • Power indicator LED 2600: 0 – 600 A AC 5.9 (.23) [2] OUTPUT Current A: 4 – 20 mA DC (Load resistance 550 Ω max.) D: 0 – 20 mA DC (Load resistance 550 Ω max.) 94 (3.70) G: 0 – 1 mA DC (Load resistance 11 kΩ max.) Z: Specify current (See OUTPUT SPECIFICATIONS) Voltage 3: 0 – 1 V DC (Load resistance 1000 Ω min.) 102 (4.02) 4: 0 – 10 V DC (Load resistance 10 kΩ min.) mm (inch) 5: 0 – 5 V DC (Load resistance 5000 Ω min.) 6: 1 – 5 V DC (Load resistance 5000 Ω min.) 4W: -10 – +10 V DC (Load resistance 20 kΩ min.) MODEL: M6SCTC–[1][2]–R 5W: -5 – +5 V DC (Load resistance 10 kΩ min.) 0: Specify voltage (See OUTPUT SPECIFICATIONS) ORDERING INFORMATION • Code number: M6SCTC-[1][2]-R POWER INPUT Specify a code from below for each [1] and [2]. DC Power (e.g. M6SCTC-56004W-R) R: 24 V DC • Special output range (For codes Z & 0) (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) Order Clamp-on current sensor separately. RELATED PRODUCTS [1] INPUT • Clamp-on current sensor (model: CLSB) Sensor CLSE • Clamp-on current sensor (model: CLSE) 5R5 0 – 5 A AC (Select “CLSE-x/CE” to comply with CE for the combination 550: 0 – 50 A AC with the sensor.) 5100: 0 – 100 A AC 5200: 0 – 200 A AC GENERAL SPECIFICATIONS 5400: 0 – 400 A AC Connection 5600: 0 – 600 A AC Input and output: Tension clamp Sensor CLSB (CE not available) Power input: Via the Installation Base (model: M6SBS) 210: 0 – 10 A AC or Tension clamp 215: 0 – 15 A AC Applicable wire size: 0.2 to 2.5 mm2, stripped length 8 mm 220: 0 – 20 A AC Housing material: Flame-resistant resin (black) 230: 0 – 30 A AC Isolation: Input to output to power 240: 0 – 40 A AC Input waveform 250: 0 – 50 A AC http://www.m-system.co.jp/ M6SCTC SPECIFICATIONS ES-7972 Rev.3 Page 1/4 MODEL: M6SCTC RMS sensing: Up to 15 % of 3rd harmonic content OUTPUT SPECIFICATIONS Zero adjustment: -2 to +2% (front) • DC Current: 0 – 20 mA DC (Output code 4W, 5W: Adjustable at 0V. No output below Minimum span: 1 mA 0mA for the code D.) Offset: Max. 1.5 times span Span adjustment: 98 to 102 % (front) Load resistance: Output drive 11 V max. Power LED: Green light turns on when the power is supplied. • DC Voltage: 0 – 10 V DC Minimum span: 1 V Offset: Max. 1.5 times span INPUT SPECIFICATIONS Load resistance: Output drive 1 mA max.; at ≥ 1 V • Clamp-on current sensor CLSE (Sensor model No.: AC input) CLSE-R5: 0 – 5 A INSTALLATION CLSE-05: 0 – 50 A Power consumption: Approx. 0.5 W CLSE-10: 0 – 100 A Operating temperature: -20 to +55°C (-4 to +131°F) CLSE-20: 0 – 200 A Operating humidity: 30 to 90 %RH (non-condensing) CLSE-40: 0 – 400 A Mounting: Installation Base (model: M6SBS) or DIN rail CLSE-60: 0 – 600 A Weight: 60 g (2.1 oz) Frequency: 50 / 60 Hz Operational range: 5 – 120 % of rating PERFORMANCE in percentage of span Overload capacity: Accuracy: ±0.5 % with input 5 – 100 % CLSE-R5: 10 A continuous Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) CLSE-05: 60 A continuous Response time: ≤ 1 sec. (0 – 90 %) CLSE-10: 120 A continuous Line voltage effect: ±0.1 % over voltage range CLSE-20: 240 A continuous Insulation resistance: ≥ 100 MΩ with 500 V DC CLSE-40: 480 A continuous Dielectric strength: 2000 V AC @1 minute (input to output CLSE-60: 720 A continuous to power to ground) Be sure that the input voltage is of 480 V or less. • Clamp-on current sensor CLSB (Sensor model No.: AC input) STANDARDS & APPROVALS CLSB-05: CE conformity: 0 – 10 A, 0 – 15 A, 0 – 20 A EMC Directive (2004/108/EC) 0 – 30 A, 0 – 40 A, 0 – 50 A EN 61000-6-4 (EMI) CLSB-10: EN 61000-6-2 (EMS) 0 – 60 A, 0 – 75 A, 0 – 100 A CLSB-20: 0 – 125 A, 0 – 150 A, 0 – 175 A 0 – 200 A, 0 – 225 A, 0 – 250 A CLSB-40: 0 – 300 A, 0 – 350 A, 0 – 400 A CLSB-60: 0 – 500 A, 0 – 600 A Frequency: 50 / 60 Hz Operational range: 5 – 120 % of rating Overload capacity: CLSB-05: 100 A continuous CLSB-10: 200 A continuous CLSB-20: 300 A continuous CLSB-40: 600 A continuous CLSB-60: 720 A continuous Be sure that the input voltage is of 440 V or less. http://www.m-system.co.jp/ M6SCTC SPECIFICATIONS ES-7972 Rev.3 Page 2/4 MODEL: M6SCTC EXTERNAL VIEW (With the cover open) Power LED Zero Adj. Span Adj. DIMENSIONS unit: mm (inch) SCREWDRIVER * INSERTION ANGLE : approx. 35° WIRE INSERTION ANGLE TEST PROBE : approx.35° max. 2 (.08) dia. 5 6 7 8 DIN RAIL HOOK DIN RAIL 35mm wide 1 2 3 4 SCREWDRIVER [0.5 (.02)] INSERTION ANGLE : approx. 40° 5.9 (.23) 102 (4.02) • When mounting, no extra space is needed between units. *Use a minus screwdriver: tip width 3.8 mm max., tip thickness 0.5 to 0.6 mm http://www.m-system.co.jp/ M6SCTC SPECIFICATIONS ES-7972 Rev.3 Page 3/4 94 (3.70) MODEL: M6SCTC SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM SOURCE Z S Isolation k Low Drift RMS Output 1 5 + Amplifier Operation Driver CLAMP-ON SENSOR OUTPUT 2 6 – l POWER LED 3 + LOAD 7 POWER 4 – 8 POWER Specifications are subject to change without notice. http://www.m-system.co.jp/ M6SCTC SPECIFICATIONS ES-7972 Rev.3 Page 4/4 CONNECTOR