MODEL: M6NXF3 For changing between suffix codes, set the Input Range Screw Terminal Ultra-Slim Signal Conditioners M6N Series Selector on the side of unit before software adjustment.) HOLD FUNCTION MODULE [2] OUTPUT (PC programmable) Current Functions & Features Z1: Range 0 – 20 mA DC • Track/Hold or Peak hold function’s selection available Voltage • 7.5-mm wide ultra-slim design with DC current signal V2: Range -10 – +10 V DC input V3: Range -5 – +5 V DC • Low profile allows the M6N module to be mounted in a (Configurator software is used to change output over the 120-mm deep panel described range of the selected suffix code. • PC programmable For changing between suffix codes, set the Output Range • High-density mounting available Selector on the side of unit before software adjustment.) • Power and status indicator LEDs • CE approval POWER INPUT Typical Applications DC Power • Monitoring peak power consumption R: 24 V DC • Monitoring the highest or lowest temperature (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) • Capturing signals from a composite analyzer performing on each sample in turn FUNCTIONS PC Configurator Software is used to change function type. 7.5 (.30) • Track/Hold • Peak hold Peak hold 102 Valley hold (4.02) Peak-to-peak hold (Peak hold-Valley hold) Factory default setting Control/Hold: Track/Hold Control/Control Logic: Hold at open 102 (4.02) mm (inch) RELATED PRODUCTS • PC configurator software (model: M6CFG) Downloadable at M-System’s web site. MODEL: M6NXF3–[1][2]–R A dedicated cable is required to connect the module to the PC. Please refer to the internet software download site or ORDERING INFORMATION the users manual for the PC configurator for applicable • Code number: M6NXF3-[1][2]-R cable types. Specify a code from below for each [1] and [2]. (e.g. M6NXF3-Z1Z1-R) GENERAL SPECIFICATIONS • Input range (e.g. 4 – 20 mA DC) Connection • Output range (e.g. 4 – 20 mA DC) Input and output: M3 screw terminal (torque 0.5 N·m) Power input: Via the Installation Base (model: M6NBS) [1] INPUT or M3 screw terminal (torque 0.5 N·m) Current Recommended solderless terminal: Max. 5.8 mm (0.23”) Z1: Range 0 – 50 mA DC (Input resistance 24.9 Ω) wide; Ones with insulation sleeve do not fit. Voltage Applicable wire size 0.2 – 2.5 mm2 S1: Range -1000 – +1000 mV DC (Input resistance 1 MΩ min.) Housing material: Flame-resistant resin (black) S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.) Isolation: Input to output to power (Configurator software is used to change input over the Overrange output: -2 – +102 % described range of the selected suffix code. (Negative current output is not available.) http://www.m-system.co.jp/ M6NXF3 SPECIFICATIONS ES-7920 Rev.1 Page 1/4 MODEL: M6NXF3 Zero adjustment: -2 to +2% (PC programming) output range provided that the minimum span is Span adjustment: 98 to 102% (PC programming) maintained. Power LED: Green light turns on when the power is supplied. Load resistance: Output drive 11 V max. Status indicator LED: Orange LED; Flashing patterns (e.g. 4 – 20 mA: 550 Ω [11 V/20 mA]) indicate different operating status of the transmitter. If not specified, the output range is 4 – 20 mA DC. Programming: Downloaded from PC; input type and range, • DC VOLTAGE output type and range, zero and span, function type, control Code V2 (wide spans) input logic, user’s linearization table (max. 101 points, Output range: -10 – +10 V DC specified within -2 to +102% for both input and output), etc. Conformance range: -10.4 – +10.4 V DC For detailed information, refer to the users manual for the Minimum span: 1 V PC configurator. Code V3 (narrow spans) Configurator connection: 2.5 dia. miniature jack; Output range: -5 – +5 V DC RS-232C level Conformance range: -5.2 – +5.2 V DC ■Recommended solderless terminal Minimum span: 0.5 V 5.5 max. 4 min. Offset: Lower range can be any specific value within the (.22) (.16) 3.2 (.13) dia. output range provided that the minimum span is maintained. Load resistance: Output drive 1 mA max. (e.g. 1 – 5 V: 5000 Ω [5 V/1 mA]) If not specified, the output range is shown below. V2: 0 – 10 V DC INPUT SPECIFICATIONS V3: 1 – 5 V DC • DC Current: Input resistor incoporated (If not specified, the input range is 4 – 20 mA DC.) INSTALLATION Input range: 0 – 50 mA DC Power consumption: Approx. 0.5 W Minimum span: 2 mA Operating temperature: -20 to +55°C (-4 to +131°F) Offset: Lower range can be any specific value within the Operating humidity: 30 to 90 %RH (non-condensing) input range provided that the minimum span is maintained. Mounting: Installation Base (model: M6NBS) or DIN rail • DC Voltage Weight: 65 g (2.3 oz) Code S1 (narrow spans) Input range: -1000 – +1000 mV DC Minimum span: 100 mV PERFORMANCE in percentage of span Code S2 (wide spans) Overall accuracy: Input accuracy + output accuracy Input range: -10 – +10 V DC Inversely proportional to the span. Minimum span: 1 V See CALCULATION EXAMPLES OF OVERALL ACURACY. Offset: Lower range can be any specific value within the • Input accuracy: (% of max. input range) input range provided that the minimum span is maintained. -1000 – +1000 mV : ±0.01 % If not specified, the input range is shown below. -10 – +10 V : ±0.01 % S1: 0 – 100 mV DC 0 – 50 mA : ±0.02 % S2: 1 – 5 V DC • Output accuracy: ±0.04 % of max. output range • CONTROL Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. span Contact rating: 3 V @1 mA Response time: ≤ 0.5 sec. (0 – 90 %) Detection levels: Line voltage effect: ±0.1 % over voltage range ≤ 0.6 kΩ / 0.5 V at close Insulation resistance: ≥ 100 MΩ with 500 V DC ≥ 15 kΩ / 2.5 V at open Dielectric strength: 2000 V AC @1 minute (input to output to power to ground) OUTPUT SPECIFICATIONS • DC CURRENT CALCULATION EXAMPLES OF OVERALL ACCURACY Output range: 0 – 20 mA DC [Example] Input Type -10 – +10 V, Input Range 1 – 5 V, Conformance range: 0 – 20.4 mA DC Output Type -5 – +5 V, Output Range 1 – 5 V Minimum span: 1 mA • Input accuracy = Max. Input Range (20 V) / Span (4 V) × Offset: Lower range can be any specific value within the 0.01 % = 0.05 % http://www.m-system.co.jp/ M6NXF3 SPECIFICATIONS ES-7920 Rev.1 Page 2/4 5.8 max. (.23) MODEL: M6NXF3 • Output accuracy = Max. Output Range (10 V) / Span (4 V) × 0.04 % = 0.1 % Accuracy= ±0.15 % STANDARDS & APPROVALS CE conformity: EMC Directive (2004/108/EC) EN 61000-6-4 (EMI) EN 61000-6-2 (EMS) EXTERNAL VIEW � FRONT VIEW (with the cover open) � SIDE VIEW Output Range Selectors 5 6 7 8 Power LED Status Indicator LED Configurator Jack Input Range Selectors 1 2 3 4 The DIP switch setting is required to select input and output types before setting a precise range using PC Configurator Software (model: M6CFG). Refer to the instruction manual for detailed procedures. http://www.m-system.co.jp/ M6NXF3 SPECIFICATIONS ES-7920 Rev.1 Page 3/4 SW2 SW1 SW2 SW1 ON ON OFF OFF 1 2 1 2 3 4 5 6 7 8 MODEL: M6NXF3 DIMENSIONS unit: mm (inch) SCREWDRIVER * WIRE INSERTION ANGLE INSERTION ANGLE : approx. 35° : approx. 55° 8–M3 SCREW TERMINAL DIN RAIL HOOK 5 6 7 8 DIN RAIL 35mm wide 1 2 3 4 [1 (.04)] SCREWDRIVER INSERTION ANGLE : approx. 40° 7.5 (.30) 102 (4.02) *Screwdriver stem diameter: 6 mm (.24”) or less • When mounting, no extra space is needed between units. SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM STATUS LED DIP SW Isolation Digital Output 5 + Computation Driver + 1 OUTPUT Low Drift INPUT 6 – 24.9ΩAmplifier POWER LED – 2 +3V + 7 3kΩ POWER 3 8 – CONTROL 4 JACK CONFIGURATOR POWER Specifications are subject to change without notice. http://www.m-system.co.jp/ M6NXF3 SPECIFICATIONS ES-7920 Rev.1 Page 4/4 102 (4.02) CONNECTOR