MODEL: M6NXAP N: 12 V pulse (100 kHz for FM, 1 kHz for PWM) Screw Terminal Ultra-Slim Signal Conditioners M6N Series P: 24 V pulse (100 kHz for FM, 1 kHz for PWM) Output modulation type and range are configurable with the DC/FREQUENCY CONVERTER configure software. The output signal type is configurable (PC programmable) with the DIP switches. Function & features • 7.5-mm wide ultra-slim design POWER INPUT • Low profile allows the M6N module mounted in a 120-mm DC Power deep panel R: 24 V DC • Converts a DC input into a FM (frequency modulation) or (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) PWM (pulse width modulated) signal • 3-port isolation • PC programmable [3] OPTIONS • High-density mounting blank: none • Power and status indicator LEDs /Q: With options (specify the specification) • CE marking SPECIFICATIONS OF OPTION: Q EX-FACTORY SETTING 7.5 (.30) /SET: Preset according to the Ordering Information Sheet (No. ESU-7837) 102 (4.02) RELATED PRODUCTS • PC configurator software (model: M6CFG) Downloadable at M-System’s web site. A dedicated cable is required to connect the module to the 102 PC. Please refer to the internet software download site or (4.02) the users manual for the PC configurator for applicable mm (inch) cable types. GENERAL SPECIFICATIONS MODEL: M6NXAP–[1][2]–R[3] Connection Input and output: M3 screw terminal (torque 0.5 N·m) ORDERING INFORMATION Power input: Via the Installation Base (model: M6NBS) • Code number: M6NXAP-[1][2]-R[3] or M3 screw terminal (torque 0.5 N·m) Specify a code from below each [1] through [3]. Recommended solderless terminal: Max. 5.8 mm (0.23”) (e.g. M6NXAP-Z1A-R/Q) wide; Ones with insulation sleeve do not fit. • Specify the specification for option code /Q Applicable wire size 0.2 – 2.5 mm2 (e.g. /SET) Housing material: Flame-resistant resin (black) Isolation: Input to output to power [1] INPUT Zero adjustment: -2 to +2 % (PC programming) Current Span adjustment: 98 to 102 % (PC programming) Z1: Range 0 – 50 mA DC (Input resistance 25 Ω) Power LED: Green light turns on when the power is supplied. Voltage Status indicator LED: Orange LED; Flashing patterns S1: Range -1000 – +1000 mV DC (Input resistance 1 MΩ min.) indicate different operating status of the transmitter. S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.) Programming: Downloaded from PC (Configurator software is used to change the input type and • Input type and range precise range.) • Modulation type (FM, PWM) • Output range • Zero and span [2] OUTPUT • User’s linearization table (max. 101 points, specified A: Open collector (100 kHz for FM, 1 kHz for PWM) within -2 to +102 %) M: 5 V pulse (100 kHz for FM, 1 kHz for PWM) http://www.m-system.co.jp/ M6NXAP SPECIFICATIONS ES-7926 Rev.1 Page 1/4 MODEL: M6NXAP • Others ■ Voltage Pulse (Refer to the instruction manual for details) High level: Rating (5, 12 or 24 V) ±10 % Configurator connection: 2.5 dia. miniature jack; Low level: ≤ 0.5 V RS-232-C level Load resistance: ■Recommended solderless terminal • ≥ 1.0 kΩ for 5 V 5.5 max. 4 min. • ≥ 2.4 kΩ for 12 V (.22) (.16) 3.2 (.13) dia. • ≥ 4.8 kΩ for 24 V Factory default: 0 to 10 kHz, Frequency modulation INSTALLATION Power consumption: Approx. 1 W Operating temperature: -20 to +55°C (-4 to +131°F) INPUT SPECIFICATIONS Operating humidity: 30 to 90 %RH (non-condensing) ■ DC Current: Input resistor incoporated Mounting: Installation Base (model: M6NBS) or DIN rail (If not specified, the input range is 4 – 20 mA DC.) Weight: 65 g (2.3 oz) Input range: 0 – 50 mA DC Minimum span: 2 mA Offset: Lower range can be any specific value within the PERFORMANCE in percentage of span input range provided that the minimum span is maintained. Accuracy: Input accuracy + output accuracy ■ DC Voltage Inversely proportional to the span. •Code S1 (narrow spans) Input conversion accuracy in percentage of input span: Input range: -1000 – +1000 mV DC • ±0.01 % for -1000 to +1000 mV Minimum span: 100 mV • ±0.01 % for -10 to +10 V •Code S2 (wide spans) • ±0.02 % for 0 to 50 mA Input range: -10 – +10 V DC Output accuracy at max. frequency (FM): Minimum span: 1 V • ±0.10 % for ≤ 10 kHz Offset: Lower range can be any specific value within the • ±0.05 % for ≤ 5 kHz input range provided that the minimum span is maintained. • ±0.02 % for ≤ 1 kHz If not specified, the input range is shown below. • For 10 kHz to 100 kHz output accuracy is following. S1: 0 – 100 mV DC Output accuracy (%) = Max. frequency (kHz) x 0.01 S2: 1 – 5 V DC Output accuracy (PWM): ±0.2 % See CALCULATION EXAMPLES OF OVERALL ACCURACY. Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. input OUTPUT SPECIFICATIONS span ■ Modulation Response time: 0.1 sec. + 1 pulse cycle of 100 % output • Frequency modulation The time between the moment when the input changes 0 % Output range: 0 to 100 % to 100 % and the moment when the first pulse changes. Max. frequency: 100 kHz Line voltage effect: ±0.1 % over voltage range Min. span: 0.01 Hz Insulation resistance: ≥ 100 MΩ with 500 V DC (The output frequency changes according to the input Dielectric strength: 2000 V AC @1 minute (input to output signal. Duty rate is approx. 50 %) to power to ground) • Pulse width modulation Output range: 1 to 99 % Usable frequency: 0.008 Hz to 1 kHz CALCULATION EXAMPLES OF OVERALL ACCURACY (According to the input signal, the output pulse width (duty 1. Frequency modulation rate) changes without change of its frequency. The E.g.: Input range -10 to +10 V, input span 1 to 5 V, max. frequency is configurable with PC Configurator software, frequency 10 kHz M6CFG.). Input accuracy = Input range (20 V) ÷ Input span (4 V) x ■ Open Collector Input conversion accuracy (0.01 %) = 0.05 % 50 V DC @ 100 mA (resistive load) Output accuracy = 0.10 % Maximum frequency: 100 kHz Overall accuracy = ±0.15 % Saturation voltage: 0.5 V DC 2. Pulse width modulation (Factory default: 0 to 10 kHz, frequency modulation) E.g.: Input range -10 to +10 V, input span 1 to 5 V, http://www.m-system.co.jp/ M6NXAP SPECIFICATIONS ES-7926 Rev.1 Page 2/4 5.8 max. (.23) MODEL: M6NXAP frequency 1 kHz Input accuracy = 0.05 % (same as above) Output accuracy = 0.20 % Overall accuracy = ±0.25 % STANDARDS & APPROVALS CE conformity: EMC Directive (2004/108/EC) EMI EN 61000-6-4: 2007 EMS EN 61000-6-2: 2005 EXTERNAL VIEW � FRONT VIEW (with the cover open) � SIDE VIEW 5 6 7 8 Power LED Status Indicator LED Output Range Selectors Configurator Jack 1 2 3 4 The output signal type is configurable with the DIP switches. Refer to the installation manual for detailed procedure. DIMENSIONS unit: mm (inch) SCREWDRIVER * WIRE INSERTION ANGLE INSERTION ANGLE : approx. 35° : approx. 55° 8–M3 SCREW TERMINAL DIN RAIL HOOK 5 6 7 8 DIN RAIL 35mm wide 1 2 3 4 [1 (.04)] SCREWDRIVER INSERTION ANGLE : approx. 40° 7.5 (.30) 102 (4.02) *Screwdriver stem diameter: 6 mm (.24”) or less • When mounting, no extra space is needed between units. http://www.m-system.co.jp/ M6NXAP SPECIFICATIONS ES-7926 Rev.1 Page 3/4 102 (4.02) SW1 SW1 ON OFF 1 2 3 4 5 6 7 8 MODEL: M6NXAP SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM STATUS LED DIP SW Isolation 25 Ω + Digital Output 1 5 + Computation Driver CURRENT OUTPUT (Z1) Low Drift – 2 6 – – Amplifier VOLTAGE POWER LED (S1, S2) 3 + + 7 POWER 4 – 8 CONFIGURATOR JACK POWER Output Connection Examples ع Open Collector ع Voltage Pulse 5 + + + + 5 6 – – – – 6 Specifications are subject to change without notice. http://www.m-system.co.jp/ M6NXAP SPECIFICATIONS ES-7926 Rev.1 Page 4/4 CONNECTOR