MODEL: M6NVF -164 – +164 mV DC Screw Terminal Ultra-Slim Signal Conditioners M6N Series -200 – +200 mV DC -15 – +15 V DC SIGNAL TRANSMITTER -25 – +25 V DC (high-accuracy, ultra-high speed response 30 μsec.) -55 – +55 V DC Functions & Features -60 – +60 V DC • 7.5-mm wide ultra-slim design • Low profile allows the M6N module mounted in a 120-mm OUTPUT deep panel Voltage • Galvanically isolates process instrumentation signals 4W: -10 – +10 V DC (Load resistance 2000 Ω min.) • 30-microsecond response • Frequency characteristics 12 kHz (-3 dB) • High-density mounting POWER INPUT • Power indicator LED DC Power R: 24 V DC Typical Applications (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) • Isolation for a vibration analyzing system • Isolation for Discharge/Charge tester GENERAL SPECIFICATIONS Connection 7.5 (.30) Input and output: M3 screw terminal (torque 0.5 N·m) Power input: Via the Installation Base (model: M6NBS) or M3 screw terminal (torque 0.5 N·m) 102 Recommended solderless terminal: Max. 5.8 mm (0.23”) (4.02) wide; Ones with insulation sleeve do not fit. Applicable wire size 0.2 – 2.5 mm2 Housing material: Flame-resistant resin (black) Isolation: Input to output to power 102 (4.02) Overrange input: -5 to +105% mm (inch) Zero adjustment: -1 to +1 % (front)) Span adjustment: 99 to 101 % (front) Power LED: Green light turns on when the power is supplied. MODEL: M6NVF–[1]4W–R ■Recommended solderless terminal 5.5 max. 4 min. (.22) (.16) 3.2 (.13) dia. ORDERING INFORMATION • Code number: M6NVF-[1]4W-R Specify a code from below for [1]. (e.g. M6NVF-04W-R) • Special input range (For codes 0: e.g. -164 – +164 mV DC) INPUT SPECIFICATIONS Input resistance: 1 MΩ min. (3 kΩ min. at power loss) [1] INPUT Voltage 2W : -100 – +100 mV DC (Input resistance 1 MΩ min.) OUTPUT SPECIFICATIONS 4W: -10 – +10 V DC (Input resistance 1 MΩ min.) Parallel load capacitance: Max. 2000 pF 5W: -5 – +5 V DC (Input resistance 1 MΩ min.) 8W: -20 – +20 V DC (Input resistance 1 MΩ min.) INSTALLATION 0 : Specify voltage Power consumption: Approx. 0.6 W (Select input range as indicated below. Input resistance 1 MΩ min.) Operating temperature: -20 to +55°C (-4 to +131°F) -20 – +20 mV DC Operating humidity: 30 to 90 %RH (non-condensing) -24 – +24 mV DC Mounting: Installation Base (model: M6NBS) or DIN rail -40 – +40 mV DC Weight: 60 g (2.1 oz) -85 – +85 mV DC http://www.m-system.co.jp/ M6NVF SPECIFICATIONS ES-7924 Rev.1 Page 1/3 5.8 max. (.23) MODEL: M6NVF PERFORMANCE in percentage of span Accuracy: ±0.01 % Temp. coefficient: ±0.005 %/°C (±0.003 %/°F) Frequency characteristics: 12 kHz, -3 dB Response time: ≤ 30 µsec. (0 – 90 %) Line voltage effect: ±0.01 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 2000 V AC @1 minute (input to output to power to ground) STANDARDS & APPROVALS CE conformity: EMC Directive (2004/108/EC) EN 61000-6-4 (EMI) EN 61000-6-2 (EMS) EXTERNAL VIEW (With the cover open) Power LED Zero Adj. Span Adj. http://www.m-system.co.jp/ M6NVF SPECIFICATIONS ES-7924 Rev.1 Page 2/3 MODEL: M6NVF DIMENSIONS unit: mm (inch) SCREWDRIVER * WIRE INSERTION ANGLE INSERTION ANGLE : approx. 35° : approx. 55° 8–M3 SCREW TERMINAL DIN RAIL HOOK 5 6 7 8 DIN RAIL 35mm wide 1 2 3 4 [1 (.04)] SCREWDRIVER INSERTION ANGLE : approx. 40° 7.5 (.30) 102 (4.02) *Screwdriver stem diameter: 6 mm (.24”) or less • When mounting, no extra space is needed between units. SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Z S Isolation Low Drift Output + + 1 5 SIGNAL Amplifier Driver OUTPUT SOURCE – – 2 6 POWER LED 3 + 7 POWER 4 – 8 POWER This unit, by its fast-response feature, is not designed to eliminate noise present in the input signal. Use a shielded twisted-pair cable to prevent noise from entering through the input wiring. Specifications are subject to change without notice. http://www.m-system.co.jp/ M6NVF SPECIFICATIONS ES-7924 Rev.1 Page 3/3 102 (4.02) CONNECTOR