MODEL: M6NPP Screw Terminal Ultra-Slim Signal Conditioners M6N Series [3]OUTPUT LOGIC N: The same as the input R: Inverted PULSE ISOLATOR Functions & Features • 7.5-mm wide ultra-slim design POWER INPUT • Low profile allows the M6N module mounted in a 120-mm DC Power deep panel R: 24 V DC • Galvanically isolates pulse rate signals (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) • High-density mounting • Power indicator and input monitor LED GENERAL SPECIFICATIONS Connection Typical Applications Input and output: M3 screw terminal (torque 0.5 N·m) • Isolating field pulse signals in order to reduce noises Power input: Via the Installation Base (model: M6NBS) • Changing e.g. dry contact signal to e.g. 5 V signals or M3 screw terminal (torque 0.5 N·m) Recommended solderless terminal: Max. 5.8 mm (0.23”) 7.5 (.30) wide; Ones with insulation sleeve do not fit. Applicable wire size 0.2 – 2.5 mm2 Housing material: Flame-resistant resin (black) Isolation: Input to output to power 102 (4.02) Chattering protection: Filter provided for mechanical contact input Power LED: Green light turns on when the power is supplied. Input monitor LED 102 (4.02) Open collector, Mechanical contact: Orange LED turns mm (inch) on when the input is ON. Voltage pulse, 2-wire current pulse: Orange LED turns on when the input is high. Input pulse sensing: DC coupled MODEL: M6NPP–[1][2][3]–R ■Recommended solderless terminal 5.5 max. 4 min. ORDERING INFORMATION (.22) (.16) 3.2 (.13) dia. • Code number: M6NPP-[1][2][3]-R Specify a code from below for each [1] through [3]. (e.g. M6NPP-CMN-R) [1] INPUT INPUT SPECIFICATIONS A1: Open collector Excitation: 12 V DC @20 mA, shortcircuit protection A2: Mechanical contact • Open Collector C: 5 V pulse (sensitivity 2 V) Maximum frequency: 100 kHz D: 12 V/24 V pulse (sensitivity 5 V) Pulse width time requirement: ≥ 5 μsec. for ON and OFF H: Two-wire current pulse Sensing: Approx. 11 V DC @2.4 mA Detecting levels: ≤ 1.8 kΩ/3 V for ON, ≥ 4 kΩ/5 V for OFF [2] OUTPUT • Mechanical Contact A1: High frequency open collector (max. 100 kHz) Maximum frequency: 30 Hz A2: Low frequency open collector (max. 30 Hz) Pulse width time requirement: ≥ 10 msec. for ON and OFF M: 5 V pulse Sensing: Approx. 11 V DC @2.4 mA N: 12 V pulse Detecting levels: ≤ 1.8 kΩ/3 V for ON, ≥ 4 kΩ/5 V for OFF P: 24 V pulse • Voltage Pulse Maximum frequency: 100 kHz Pulse width time requirement: ≥ 5 μsec. for high and low http://www.m-system.co.jp/ M6NPP SPECIFICATIONS ES-7919 Rev.3 Page 1/4 5.8 max. (.23) MODEL: M6NPP levels STANDARDS & APPROVALS Waveform: Square or sine CE conformity: Input impedance: ≥ 10 kΩ EMC Directive (2004/108/EC) Max. voltage between input terminals: 50 V EN 61000-6-4 (EMI) Detecting H level EN 61000-6-2 (EMS) 5 V pulse: ≥ 3 V 12 V, 24 V pulse: ≥ 6 V Detecting L level 5 V pulse: ≤ 1 V 12 V, 24 V pulse: ≤ 4 V • Two-Wire Current Pulse Max. frequency: 100 kHz Input resistance: Receiving resistor 200 Ω Input range: 0 – 25 mA Detecting levels: ≤ 5 mA for Lo, ≥ 15 mA for Hi OUTPUT SPECIFICATIONS • High Frequency Open Collector: 50 V DC @100 mA (resistive load) Maximum frequency: 100 kHz Saturation voltage: 0.5 V DC • Low Frequency Open Collector: 50 V DC @100 mA (resistive load) Maximum frequency: 30 Hz Timer: Limits within 75 ±25 msec. ON time for output logic non-inverted OFF time for output logic inverted Saturation voltage: 0.5 V DC • Voltage Pulse Maximum frequency: 100 kHz High level: Rating (5, 12 or 24 V) ±10 % Low level: ≤ 0.5 V Load resistance: ≥ 1.0 kΩ for 5 V ≥ 2.4 kΩ for 12 V ≥ 4.8 kΩ for 24 V INSTALLATION Power consumption: Approx. 1 W Operating temperature: -20 to +55°C (-4 to +131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Installation Base (model: M6NBS) or DIN rail Weight: 60 g (2.1 oz) PERFORMANCE Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 2000 V AC @1 minute (input to output to power to ground) http://www.m-system.co.jp/ M6NPP SPECIFICATIONS ES-7919 Rev.3 Page 2/4 MODEL: M6NPP EXTERNAL VIEW (With the cover open) Power LED Input Monitor LED OUTPUT LOGIC VOLTAGE PULSE INPUT TYPE PULSE LOGIC INPUT OPEN COLLECTOR OUTPUT H H OFF Non Inverted L L ON Voltage Pulse Input H H OFF 2-wire Current Pulse Inverted L L ON OFF H OFF Non Inverted ON L ON Mechanical Contact Open Collector OFF H OFF Inverted ON L ON DIMENSIONS unit: mm (inch) SCREWDRIVER * WIRE INSERTION ANGLE INSERTION ANGLE : approx. 35° : approx. 55° 8–M3 SCREW TERMINAL DIN RAIL HOOK 5 6 7 8 DIN RAIL 35mm wide 1 2 3 4 [1 (.04)] SCREWDRIVER INSERTION ANGLE : approx. 40° 7.5 (.30) 102 (4.02) *Screwdriver stem diameter: 6 mm (.24”) or less • When mounting, no extra space is needed between units. http://www.m-system.co.jp/ M6NPP SPECIFICATIONS ES-7919 Rev.3 Page 3/4 102 (4.02) MODEL: M6NPP SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM INPUT MONITOR LED Isolation * Waveform Output + + 1 Timer 5 Shaper Driver INPUT OUTPUT – – 2 6 SENSOR EXCITATION POWER + + 3 12V Supply 7 LED POWER – 4 8 Base Socket POWER *Low freq. open collector output only. Input Connection Examples Output Connection Examples � Mechanical Contact or Open Collector � 2-Wire Current Pulse � Open Collector • Built-in Excitation + + + + 1 5 200Ω – 1 – – – 2 6 – – 2-WIRE +12V 2 PWR PICK-UP + + 3 +12V 5kΩ + 3 � Voltage Pulse � Voltage Pulse + 5 + • External DC Supply + + 1 6 – – 200Ω – 2-WIRE 1 – PICK-UP – + 2 – +12V 2 PWR + + + +12V 3 – + 3 DC SUPPLY Specifications are subject to change without notice. http://www.m-system.co.jp/ M6NPP SPECIFICATIONS ES-7919 Rev.3 Page 4/4 CONNECTOR