Combo NTSC Waveform Monitor /Vectorscope ■ 4:2:2 Serial Component Monitoring ■ Auto Response to 525/60 and 625/50 ■ Two SDI Inputs (A&B) ■ One Set 3-Wire Component/Composite Analog Inputs ■ Active SDI Output from Selected A or B Input ■ SDI Input Level in Terms of Equivalent Cable Length ■ Digital Status Readout with EDH Error ■ Hex Readout of all Pixels (Data Points) ■ User Selected Local and Remote Error Alarms ■ YPbPr or GBR Waveforms in Parade or Overlay ■ 3-Wire Analog Picture Outputs (YPbPr or GBR) ■ Ten Presets Store all Settings but INTEN, FOCUS, ILLUM and POWER ON-OFF LV5100D ■ Picture Display of Y or G (with Line-Select Strobe) ■ Component Vector Display ■ X-Y Stereo Display with Calibration for 0, +2, +4 dB Capable of handling SDI as well as analog components, Presets may be recalled from the front panel or by remote the LV5100D provides comprehensive waveform, vector, control. A touch on the DIGITAL key opens an extensive timing (for use with the bowtie), stereo-audio and picture presentation of digital conditions. These include status monitoring facilities. Menu-driven control functions boards that report signal status, the condition of the data extend familiar observations into highly specialized areas stream in terms of equivalent cable length from an ideal that include overlay or parade displays of YPbPr or GBR; source, the pass or remove EAV/SAV signals from the waveform and presence of ANC data and EDH codes, embedded audio picture. Passing EAV/SAV also allows observation of and the time that EDH error was detected. The cable signals normally blanked such as embedded audio and length indicator provides a simple gauge as to the ANC signals like the EDH codes. Other adjustments proximity of the “digital cliff”. Hex data is presented for all found in the SYSTEM menu include line select setup, 1716 data points on the raster line that is selected vector setup, DC restorer characteristics, calibration, manually or captured as the result of a TRS error. In time/calendar settings and much more. Ten available pre- addition, local and remote alarms may be triggered by the sets store front-panel settings for all observation setups and operator’s choice of monitoring parameters. include positioning, and the use of line select and cursor measurements. k e y s p e c i f i c a t i o n s CRT VERTICAL SECTION LINE SELECTOR Type 525 lines 625 lines Deflection Accuracy 150 mm rectangular, P31 Phosphor FLD 1 & 2 Lines 1 to 262 Lines 1 to 312 ± 1% referenced to 1 V p-p full scale Accelerating Potential FRAME Lines 1 to 525 Lines 1 to 625 ± 2% x5 16.5 kV PRESET FUNCTION ± 0.5% cursor measurements Scales Ten sets of front panel settings can be Filter Characteristics Internal, illuminated graticule stored and recalled with exception of Flat (waveforms) INTEN, READOUT INTEN, ROTATION, Within 2% 25Hz to 6 MHz Electronically-generated (vector and FOCUS, ILLUM and POWER (on-off) (audio) Lowpass CURSOR MEASUREMENTS SIGNAL HANDLING 35 dBm min. at 3.58 MHz Available Cursors Digital Dif’d Step 2 horz, ∆ and REF Applicable standards: ITU-R601-3, 400 kHz bandpass 2 vert, ∆ and REF ITU-R656-1, SMPTE 125M-1992, HORIZONTAL SECTION Accuracy SMPTE 295M Operating Modes Analog 0.5% Overlay, Parade,Timing,Waveform,Vector 3-wire analog component POWER REQUIREMENTS Picture,Audio GBR or YPbPr 90 V - 250 V ac, 48 to 440 Hz, 70 W SERIAL DIGITAL INPUTS EDH FUNCTION PHYSICAL Number of Inputs Applicable Standard Size (W x H x D) 2 sets, passive loop-through 3 1 5 SMPTE RP-165 8 /8 x 5 /4 x 16 /8 in. Return Loss Equivalent Line-Length Function 215 x 132 x 423 mm ≥ 25 dB min, 1 to 270 MHz Reads out serial signal strength in terms Weight ANALOG INPUTS 11 lbs., 5 kg (not including cabinet) of equivalent length of 5C-2V or Number of Analog Inputs SUPPLIED ACCESSORIES Belden 8281 coaxial cable 1 set of 3 inputs, passive loop-through 5 Spare Illumination Lamps DATA READOUT REF Input 2 8-32 Rackmount Screws 1 set, passive loop-through Address 0000-1715 in hex line select or Spare Fuse OUTPUT error trigger AVAILABLE OPTIONS Serial Digital Active Output CAL Carrying Case with Handle & Feet Retransmission of selected serial input Amplitude Analog Picture Monitor Output (LR-2427I-U) 1 V ± 0.5% Format: GBR or YPbPr Rackmount Adapter (LR-2400VI) Frequency Response White Phosphor CRT (NS-305) 25 Hz to 6 MHz RGB WFM Sequence (GBR normal) (NS-298)