JASPER ELECTRONICS 1580 No. Kellogg Dr. Anaheim, Ca., 92807 Ph: (714) 917-0749 Fax: (714) 917-0786 Email: r.nishimoto@jasperelectronics.com Web: www.jasperelectronics.com ® CompactPCI 250 Watt – 3U 8HP Power Supplies ® (PICMG COMPLIANT*) Features: 9 Standard PCI Output Voltages: 5.0V, 3.3V, ±12.0V, with Variable Currents. 9 Hot Swap, N+1 Redundant with Internal OR-ing Diodes. 9 .99 Power Factor Corrected AC 90-264V Input, or DC 36-72V. 9 Current Sharing on 5.0V, 3.3V and +12.0V Outputs. 9 Standard 47 Pin Connector Configuration. 9 Custom Configurations To Meet User Specified Requirements. 9 Excellent Performance, Competitively Priced. 9 2 Year Warranty. ® 9 Complies With All Requirements Of PICMG Power Interface Specifications. 9 Fully Compliant with the EU RoHS Directive.** 9 cCSAus, NEMKO, CE Marked. ® ® *CompactPCI and PICMG are registered trademarks of Cat.# 02127-006 H the PCI Industrial Computer Manufacturers Group. **See Ordering Information. JASPER ELECTRONICS PCI 250W SERIES GENERAL PRODUCT SPECIFICATIONS: Over/Under Shoot .......... None at turn-on or turn-off. -INPUT- Under Voltage Warning.. Any output dropping below 10% of nominal Voltage/Current .............. AC 90-264V, 3.6A max, 47-63Hz, 1 Phase; or, triggers the power fail warning signal. DC 36-72, 6.55A@48V nom (9.0A max). Fusing ............................ Internal line fuse provided, non-user serviceable. -SIGNALS, INDICATORS and CONTROLS- AC- 4.0A, 250V; DC- 10.0A. Remote Enable .............. Enabled by closed circuit or TTL logic 0. Power Factor.................. 0.99 line PFC typical at AC 115V, full load. Disabled by open circuit or TTL logic 1. Inrush Current ................ Thermistor soft start. ~25ºC AC cold start current Remote Inhibit ................ Enabled by open circuit or TTL logic 1. 15Apk @ AC 115V; 30Apk @ AC 230V. Disabled by closed circuit or TTL logic 0. Transient Protection ....... MOV. Withstands transients as specified by Power Fail Warning........ Loss of input AC causes a TTL compatible signal IEEE C62.41 3KV (differential and common to go low >4msec prior to V1 or V2 output drop- mode). ping out of regulation. At AC turn-on, signal stays low until outputs are in regulation. AC and DC EMI Filtering ................... Meets IFCC Level A, and EN 55022 Level A input: PF signal triggered by an under voltage (conducted). condition on V1 or V2 outputs. Efficiency........................ 78% typical at AC 115V, full load. LED Indicator ................. Dual LEDs. Green indicates input power ON and outputs within regulation. Off or Amber indicates Redundant/Hot Swap ..... Full power N+1 redundant, hot swap capable. input and/or output power fault. -OUTPUTS- -OPERATING ENVIRONMENT- Voltage/Current (V/A)....................V1 V2 V3 V4 Operating Temperature.. 0º – 50ºC ambient at full load, with specified Model: PCI254-1022-4... 5.0/33 3.3/33 +12/6.0 –12/1.0 airflow. 5.0/33 3.3/33 +12/6.0 –12/1.0 PCI254-1022-4-P Total loading on all outputs not to exceed 250W. Cooling ........................... A minimum of 20 cfm / 600 lfm direct forward Maximum combined load of V1+V2 not to exceed 55.0A airflow required to achieve full rated power and specified MTBF. Consult factory for derating Model: DPCI254-1022-4 5.0/33 3.3/33 +12/6.0 –12/1.0 guidelines with reduced or reversed airflow. DPCI254-1022-4-P 5.0/33 3.3/33 +12/6.0 –12/1.0 Total loading on all outputs not to exceed 250W. Relative Humidity ........... Up to 90% RH, non-condensing. Maximum combined load of V1+V2 not to exceed 55.0A. Operational Vibration ..... 2.0G peak, 5 – 500Hz along three orthogonal Minimum Loading........... 5% minimum on V1 for standard models; none axis. required for option “P” models. Storage Temperature ..... -40º to 85ºC. Line Regulation .............. At the Sense Point, Over Full Input Range <±1%, sense leads connected. Altitude ........................... Operating to 10,000 ft; Storage to 30,000 ft. Load Regulation ............. Output voltage droops with increasing load. MTBF.............................. Designed for 150,000 hrs at 25ºC. Stability........................... Output drift <±0.2% after 20 minute warm-up. -INTERCONNECT- Temp. Coefficient ........... <±0.02%/ºC, 0º - 50ºC, after 20 minute warm-up. I/O Connectors. Request JE Outline Configuration Drawing #02102-000 (AC), 02600-000 (DC), or refer to the chart in this catalog for pin function Dynamic Response ........ Less than 3% deviation with a 25% load change identification- at 1A/µsec. Output returns to within 1% in less 47 Circuit .................... Positronic Ind. P/N PCIH47M400A1. than 300µsec. Mates with PI P/N PCIH47F300A1. Ripple and Noise Note: Use of the specified mating connector is required to insure proper (PARD)........................... For all outputs, 50mV max or 1% peak-to-peak "make/break" sequential contact sequence. nominal, which ever is greater, DC to 20MHz bandwidth with a coaxial probe and 0.1µF/22µF -MECHANICAL- capacitors at the output terminals. Outline............................ 3U x 8HP front panel. Refer to JE Outline Dwg Current Sharing/ #02102-000 (AC), 02600-000 (DC) or the Parallel N+1 Operation... V1, V2, V3 Outputs. Single wire connection for Mechanical Outline in this catalog. Complies with ±10% current sharing between any number of ® all current PICMG CompactPCI specifications. units. Mixing standard and opt. “P” models is not recommended. Retaining Latches .......... Supplied with a single Rittal #3686.135 Type VII (Telecom) Lower Latch. Other manufacturers Remote Sense ............... V1, V2, V3 outputs compensate for up to 0.25V and types available. Consult factory. total line drop in the load cables. Outputs are internally sensed if leads are opened. Guide Rails..................... Supplied with 0.260[6.61mm] offset guide rails for use with Rittal 3687.832 (or equivalent) PSU Hold-Up Time ................. Outputs remain in regulation >15msec minimum guides. following loss of AC power at low line, full load. Over Current/Short Front Panel Overlay ....... Supplied with Lexan overlay and JE Logo. May Circuit Protection............ Current limit on all outputs. Automatic recovery be deleted, or supplied with customer specified when overload is removed. logo or other information. Consult factory. Over Temperature Protection ....................... Internal temperature sensing. Causes all outputs Weight Approx: 1.8 lbs / 1.06 kgs. to shut down. Automatic recovery. -SAFETY- Over Voltage Protection ....................... Non-crowbar type. Any output that exceeds 25% Recognized to Canadian and U.S. Bi-National Standard CSA C22.2 ±10% of nominal Vout will cause all outputs to No. 60950-1-03 / UL 60950-1 (2001) (cCSAus Mark); latch off. Remote inhibit, enable or input recycle NEMKO certified to EN60950 Ed. 1 (2001) (N Mark). CE Marked. required to reset. JASPER ELECTRONICS PCI 250W SERIES 47 Pin I/O Connector Functions: (1) (1) PIN# SEQ FUNCTION PIN# SEQ FUNCTION 01-04 2 +5.0V V1 Output. 33 2 +S2 +3.3V (V2) Remote Sense. 05-12 2 GND V1+V2 Return. 34 2 S-RTN Sense Return for V1, V2, V3. 13-18 2 +3.3V V2 Output. 35 3 ISHR-1 +5.0V (V1) Current Share. 19 2 GND V3 Return. 36 2 +S3 +12.0V (V3) Remote Sense. 20 2 +12.0V V3 Output. 37 2 N/C No Connection (Reserved). 21 2 -12.0V V4 Output. 38 2 DEG Thermal Degrade Signal. 22 2 RTN Signal Return. 39 2 R/INH Remote Inhibit. Close circuit to GND. 23 2 N/C No Connection (Reserved). 40 2 N/C No Connection (Reserved). 24 2 GND V4 Return. 41 3 ISHR-2 +3.3V (V2) Current Share. 25,26 2 N/C No Connection (Reserved). 42 2 PF Power Fail Signal. 27 3 R/EN Remote Enable. Close circuit to GND. 43 2 N/C No Connection (Reserved). 28 2 N/C No Connection (Reserved). 44 3 ISHR-3 +12.0V (V3) Current Share. 29 2 V1-ADJ V1 Remote Voltage Adjust. 45 1 PE Protective Earth (chassis) Ground. 30 2 +S1 +5.0V (V1) Remote Sense. 46 2 Input Pwr PCI: Neutral (N) ACC Power Input 31 2 N/C No Connection (Reserved). DPCI: +DC. 32 2 V2-ADJ V2 Remote Voltage Adjust. 47 2 Input Pwr PCI: Line (L) AC Power Input. DPCI: -DC. (1) Contact mating sequence. 1= First to make/Last to break. Backplane Connector Locations, Viewed from the Front of the Enclosure (Not to Scale) 4.08 + L x 5.08 [.161] [.200] 7.62 [0.3] 122.5 [4.82] c L (128.7) [5.07] 37.60 [1.48] 61.25 [2.41] PIN 1 N x 20.32 + 7.40 3.10 [.800] [.291] [0.12] FIRST INTERBOARD LAST INTERBOARD SEPARATION PLANE SEPERATION PLANE JASPER ELECTRONICS PCI 250W SERIES Mechanical Outline (Dimensions in millimeters [inches]) 169.4 ±.04 [6.67] 8HP SEE DETAIL A 40.52 3.1 [1.59] 2.5 162.6 [0.12] Typ. [0.10] [6.40] Typ. 122.5 3U [4.82] 128.7 Typ. [5.07] 100.0 Typ. [3.94] FORWARD AIRFLOW 6.61 DIRECTION 7.5 [.260] [0.30] Typ. 8HP (Interboard Separation Plane) Front View, w/Std. Telecom Latch 47 37.1 46 [1.46] 45 42 44 22 23 19 20 2 1 47P DETAIL A I/O CONNECTOR PIN ID NOT TO SCALE -LIMITED WARRANTY POLICY- All Jasper Electronics (JE) standard model power supplies and products are guaranteed to be free of defects in work- manship and materials for a minimum of two (2) years from the date of original shipment, when operated within specification. This warranty applies only to defects that result in a failure to perform to published specifications. Non- standard (custom) power supplies and products may be warranted on an individual basis. The unused portion of this warranty is fully transferable with the original equipment in which the power supply is installed. JASPER ELECTRONICS PCI 250W SERIES ORDERING INFORMATION: A 4 to 6-character option code is required following the base model description to define the desired model configuration. Codes added in the following sequence, 1 from each required category: ∗ PCI254-1022- (1) -(2) (3) (4) (5) (6) ∗Input: Base Model Connector Internal Latch Overlay -MXXXX RoHS AC – Blank w/ V Code. Type V1 Type Type User Compliant out DC – D Preload Specified Model 254 – 250W, Config. 4 Output - ∗ Configuration Options - Option: Code: (1) Connector Type.......... 4 = 47 pin (PICMG standard); (2) Internal Preload... Blank = Standard configuration. Refer to minimum external preload requirements in the general specifications. P = Optional internal preload on V1. (3) Latch Type .................S = Standard Telecom Type VII; O = Optional Type IV; N = None provided. (4) Overlay.......................S = Standard (JE Logo, model designation, etc); B = Blank overlay (No logo, model designation, etc); N = No overlay provided; NN = No overlay; in addition, the front panel including the EMI strip is also deleted. For user provided panel or custom enclosure applications. Note: Removal of the panel does not violate safety enclosure requirements or integrity. Contact the factory for panel fastener type, max penetration depth and location information. *M = Custom overlay– user specified. May require a factory assigned custom model code. (* - may incur additional cost. Consult factory.) (5) Custom Configuration ............ M = Modified, followed by a factory assigned 4-digit number to identify a user specified configuration. Such models may include special or non-standard features and/or options, or be in a configuration differing sufficiently from the design of the approved similar standard model from which it is derived to require re-evaluation of all or part of the design to insure continuing compliance with all safety requirements. Option codes 2,3,4 may not be present in the model description as these requirements are generally included in the user specifi- cation documentation on file with the factory. Consult the factory for exact requirements. (May incur additional cost. Consult the factory.) (6) RoHS Compliant ....... G = Jasper products that are fully compliant with the requirements of Directive 2002/95/EC Restrictions of Hazardous Substances (RoHS) are identified with the letter code “G” either included in or adjacent to the model description on the unit labels and related documents (sales orders, etc). All materials, processes and packaging used in the assembly and shipping of this product comply. Note: non-RoHS compliant standard models only available until existing stock is depleted. User requests for non-RoHS or RoHS-5 (lead exception) versions may be available under the “-M” custom configuration option, at additional cost. Minimum order quantities may apply. Consult the factory. Examples: PCI254-1022-4-PSS DPCI254-1022-4-PNNNG DPCI254-1022-4-M5412 G All statements and technical information contained herein are believed by JE to be reliable as of the publication date of this document, but the accuracy or completeness is not guaranteed, and JE reserves the right to change specifications without prior notification. However, every reasonable effort will be made by JE to inform users of JE products of changes to design form, fit or function that may affect the user's applications. JE manufactures a quality product, equal to any available in the marketplace; however, these products are intended to be used in accordance with the specifications described in this catalog. Any use or application that deviates from the stated operating specifications is not recommended and may be unsafe. 02127-006 H