EEmail : sales@rackmountmart.co Tel:510-226-8368 Fax:510-226-8968 MODEL : PS2013 / TC-3U40 ( ATX 400W for 3U) 1. Specification 1.1 AC Input Voltage: 95 to 132 or 185 to 264 Auto selectable 50 to 60 Hz. 1.2 DC Output: 400W maximum Output-1 Output-2 Output-3 Output-4 Output-5 Voltage: +5V DC +12V DC -5V DC -12V DC +3.3V DC Maximum Load: 40A 15A 0.5A 0.8A 20A Minimum Load: 3A 2A 0.1A 0.1A 0.3A Ripple: 50mv 120mv 50mv 120mv 40mv Ripple/Noise: 100mv 150mv 100mv 240mv 40mv Line Regulation: ±1﹪ ±1﹪ ±1﹪ ±1﹪ ±1﹪ ±5﹪ ±5﹪ ±10﹪ ±10﹪ ±5﹪ Output Regulation: Cross Regulation: ±5﹪ ±5﹪ ±10﹪ ±10﹪ ±5﹪ Note: 1. Noise Test – Noise bandwidth is from DC to 20 MHz. 2. Ripple frequencies greater than 1MHz shall be attenuated by the measurement System. 3.Add 0.1uF/10uF capacitor at output connector terminals for ripple and noise measurements. 4.The combined total power from +5V and +3.3V shall not exceed 150W. 5.+5V SB DC Output 1.5A.（Peak 2A） 1.3 PS-ON Remote On/Off Control: When PS-ON is pulled to TTL Low, the DC output is to be enabled. When PS-OFF is pulled to TTL high, the DC output is to be disabled. 1.4 PW-OK PW-OK is power good signal and should be asserted high by the power supply to indicate that +5VDC and +3.3VDC output are above the under voltage thresholds of the power supply TTL. compatible signal out with 100ms to 500ms. Timing of PS-ON, PW-OK, and Germane Voltage Rails Although there is no requirement to meet specific timing parameters, The following signal timings are recommended: 2ms≦T2≦200ms 100ms≦T3≦500ms T4＞1ms T5≦10ms 1.5 Efficiency: ≧ 67﹪at full load.(Normal Line) 1.6 Hold-Up Time: 16ms at maximum load & normal input voltage. 2.PROTECTIONS 2.1 OVER-VOLTAGE PROTECTION Standard on +5.0V output, set at 6.25VDC ± 075VDC. 2.2 SHORT CIRCUIT PROTECTION A short circuit placed between the DC Return and the output shall cause No damage and the power supply shall shutdown. 2.3 OVER POWER PROTECTION The power supply shall shut down when output power exceeds 130﹪to 160﹪ of full load and require a power on cycle be performed by the operate 2.4 NO LOAD OPERATION No parts shall be damaged on the power supply. 3. ENVIRONMENT TEMPERATURE 3.1 Operation Temperature: 0℃ to 50℃ 3.2 Cooling: By forced air 3.3 Storage Temperature:-20℃ to 70℃ 3.4 Humidity: 5 to 90﹪non-condensing. 4. RELIABILITY 4.1 MTBF OF POWER SUPPLY ELECTRONIS 100,000 hours at full load and 25℃ ambient temperature 4.2 LIFE EXPECTANCY OF FAN 40,000 hours at 40℃ 5. AGENCY APPROVALS UL 1950 QQGQ2 UL 1950 QQGQ8 TUV Rheinland ( EN60950, IEC950 mod ) CB Certification 6. EMI FCC part 15, Subpart B, Class B EN55022 CISPR22 Class B, CE Make EN61000-3-3;1995 EN61000-4-2, -3, -4, -5, -6, -8, -11 7. DIMENSION L 180 x W 117 x H 86 mm 8. PINOUTS OF CONNECTORS 6 x 5.25” , 1 x 3.25”, 1 x ATX-20Pin ( for motherboard), 1 x AUX 12V Power Connector