INTERNATIONAL RECTIFIER IRF7106
Description
HEX/MOS N/P-CH DL 20/-20V 8-SOIC
Part Number
IRF7106
Price
Request Quote
Manufacturer
INTERNATIONAL RECTIFIER
Lead Time
Request Quote
Category
PRODUCTS - I
Datasheet
Extracted Text
PD - 9.1098B IRF7106 PRELIMINARY ® HEXFET Power MOSFET Advanced Process Technology N-CHANNEL MOSFET Ultra Low On-Resistance N-Ch P-Ch 1 8 S1 D1 Dual N and P Channel Mosfet 2 7 G1 D1 Surface Mount V 20V -20V DSS 3 6 Available in Tape & Reel S2 D2 Dynamic dv/dt Rating R 0.125Ω 0.20Ω 4 5 DS(on) G2 D2 Fast Switching P-CHANNEL MOSFET I 3.0A -2.5A D Top View Description Fourth Generation HEXFETs from International Rectifier utilize advanced processing techniques to achieve the lowest possible on-resistance per silicon area. This benefit, combined with the fast switching speed and ruggedized device design for which HEXFET Power MOSFETs are well known, provides the designer with an extremely efficient device for use in a wide variety of applications. The SO-8 has been modified through a customized leadframe for enhanced thermal characteristics and multiple-die capability making it ideal in a variety of power applications. With these improvements, multiple devices can be used in an SO-8 application with dramatically reduced board space. The package is designed for vapor phase, infra-red, or wave soldering techniques. Power dissipation of greater than 0.8W is possible in a typical PCB mount application. Absolute Maximum Ratings Max. Parameter Units N-Channel P-Channel I @ T = 25°C Continuous Drain Current, V @ 10V 3.0 -2.5 D C GS I @ T = 70°C Continuous Drain Current, V @ 10V 2.5 -2.0 A D C GS I Pulsed Drain Current 10 -10 DM W P @T = 25°C Power Dissipation 2.0 D C Linear Derating Factor 0.016 W/°C V Gate-to-Source Voltage ± 20 V GS dv/dt Peak Diode Recovery dv/dt 3.0 -3.0 V/ns T T Junction and Storage Temperature Range -55 to + 150 °C J, STG Thermal Resistance Parameter Min. Typ. Max. Units R Junction-to-Ambient (PCB Mount)** –––– –––– 62.5 °C/W θJA ** When mounted on 1" square PCB (FR-4 or G-10 Material). For recommended footprint and soldering techniques refer to application note #AN-994. Revision 3 69 IRF7106 Electrical Characteristics @ T = 25°C (unless otherwise specified) J Parameter Min. Typ. Max. Units Conditions N-Ch 20 — — V = 0V, I = 250µA GS D V Drain-to-Source Breakdown Voltage (BR)DSS V P-Ch -20 — — V = 0V, I = -250µA GS D N-Ch — 0.037 — Reference to 25°C, I = 1mA D ΔV /ΔT Breakdown Voltage Temp. Coefficient (BR)DSS J V/°C P-Ch — -0.022 — Reference to 25°C, I = -1mA D — — 0.125 V = 10V, I = 1.0A GS D N-Ch — — 0.25 V = 4.5V, I = 0.50A GS D R Static Drain-to-Source On-Resistance DS(ON) Ω — — 0.20 V = -10V, I = -1.0A GS D P-Ch — — 0.35 V = -4.5V, I = -0.50A GS D N-Ch 1.0 — — V = V , I = 250µA DS GS D V Gate Threshold Voltage GS(th) V P-Ch -1.0 — — V = V , I = -250µA DS GS D N-Ch — 4.4 — V = 15V, I = 3.0A DS D g Forward Transconductance fs S P-Ch — 3.0 — V = -15V, I = -3.0A DS D N-Ch — — 2.0 V = 16V, V = 0V DS GS P-Ch — — -2.0 V = -16V, V = 0V DS GS I Drain-to-Source Leakage Current DSS µA N-Ch — — 25 V = 16V, V = 0V, T = 125°C DS GS J P-Ch — — -25 V = -16V, V = 0V, T = 125°C DS GS J I Gate-to-Source Forward Leakage N-P –– — ±100 nA V = ± 20V GSS GS N-Ch — 9.1 25 Q Total Gate Charge g N-Channel P-Ch — 11 25 I = 2.3A, V = 10V, V = 10V D DS GS N-Ch — 1.2 — Q Gate-to-Source Charge gs nC P-Ch — 1.6 — P-Channel N-Ch — 2.5 — Q Gate-to-Drain ("Miller") Charge I = -2.3A, V = -10V, V = -10V gd D DS GS P-Ch — 3.5 — N-Ch — 5.0 15 t Turn-On Delay Time d(on) N-Channel P-Ch — 10 40 V = 20V, I = 1.0A, R = 6.0Ω, DD D G N-Ch — 10 20 t Rise Time r R = 20Ω D P-Ch — 15 40 ns N-Ch — 29 50 t Turn-Off Delay Time P-Channel d(off) P-Ch — 41 90 V = -20V, I = -1.0A, R = 6.0Ω, DD D G N-Ch — 22 50 t Fall Time R = 20Ω f D P-Ch — 39 60 L Internal Drain Inductace N-P — 4.0 — Between lead tip D nH L Internal Source Inductance N-P — 6.0 — and center of die contact S N-Ch — 300 — C Imput Capacitance N-Channel iss P-Ch — 280 — V = 0V, V = 15V, ƒ = 1.0MHz GS DS N-Ch — 260 — C Output Capacitance pF oss P-Ch — 250 — P-Channel N-Ch — 62 — C Reverse Transfer Capacitance V = 0V, V = -15V, ƒ = 1.0MHz rss GS DS P-Ch — 86 — Source-Drain Ratings and Characteristics Parameter Min. Typ. Max. Units Conditions N-Ch — — 1.7 I Continuous Source Current (Body Diode) S P-Ch — — -1.6 A N-Ch — — 10 I Pulsed Source Current (Body Diode) SM P-Ch — — -10 N-Ch — 0.90 1.2 T = 25°C, I = 1.6A, V = 0V J S GS V V Diode Forward Voltage SD P-Ch — -0.90 -1.6 T = 25°C, I = -1.3A, V = 0V J S GS N-Ch — 69 100 N-Channel ns t Reverse Recovery Time rr P-Ch — 69 100 T = 25°C, I = 1.25A, di/dt = 100A/µs J F N-Ch — 58 120 P-Channel nC Q Reverse Recovery Charge rr T = 25°C, I = -1.25A, di/dt = 100A/µs P-Ch — 91 180 J F t Forward Turn-On Time N-P Intrinsic turn-on time is neglegible (turn-on is dominated by L +L ) on S D N-Channel I ≤ 2.3A, di/dt ≤ 100A/µs, V ≤ V , T ≤ 150°C Notes: SD DD (BR)DSS J P-Channel I ≤ -2.3A, di/dt ≤ 50A/µs, V ≤ V , T ≤ 150°C SD DD (BR)DSS J Repetitive rating; pulse width limited by max. junction temperature. ( See fig. 23 ) Pulse width ≤ 300µs; duty cycle ≤ 2%. 70 IRF7106 N-Channel 100 100 VGS VGS TOP 15V TOP 15V 10V 10V 8.0V 8.0V 7.0V 7.0V 6.0V 6.0V 5.5V 5.5V 5.0V 5.0V BOTTOM 4.5V BOTTOM 4.5V 4.5V 10 4.5V 10 1 1 20µs PULSE WIDTH 20µs PULSE WIDTH T = 150°C TJ = 25°C J 0.1 A 0.1 A 0.01 0.1 1 10 100 0.01 0.1 1 10 100 V , Drain-to-Source Voltage (V) V , Drain-to-Source Voltage (V) DS DS Fig 2. Typical Output Characteristics, Fig 1. Typical Output Characteristics, o o T = 150 C T = 25 C J J 100 2.0 I = 3.0A D 1.5 T = 25°C J 1.0 T = 150°C J 0.5 V = 15V DS 20µs PULSE WIDTH V = 10V GS 10 0.0 A A 4 5 6 7 8 9 10 -60 -40 -20 0 20 40 60 80 100 120 140 160 V , Gate-to-Source Voltage (V) T , Junction Temperature (°C) GS J Fig 4. Normalized On-Resistance Fig 3. Typical Transfer Characteristics Vs. Temperature 800 20 V = 0V, f = 1MHz I = 2.3A GS D C = C + C , C SHORTED V = 10V iss gs gd ds DS C = C rss gd C = C + C oss ds gd 16 600 C oss 12 C iss 400 8 200 C 4 rss FOR TEST CIRCUIT SEE FIGURE 11 0 A 0 A 0 2 4 6 8 10 12 14 1 10 100 Q , Total Gate Charge (nC) V , Drain-to-Source Voltage (V) G DS Fig 5. Typical Capacitance Vs. Fig 6. Typical Gate Charge Vs. Drain-to-Source Voltage Gate-to-Source Voltage 71 C, Capacitance (pF) I , Drain-to-Source Current (A) I , Drain-to-Source Current (A) D D R , Drain-to-Source On Resistance DS(on) I , Drain-to-Source Current (A) V , Gate-to-Source Voltage (V) (Normalized) D GS IRF7106 N-Channel 100 100 OPERATION IN THIS AREA LIMITED BY RDS(on) 10 10 T = 150°C J 1ms T = 25°C J 10ms 1 1 100ms T = 25°C A T = 150°C J V = 0V GS Single Pulse 0.1 A 0.1 A 0.4 0.6 0.8 1.0 1.2 1.4 0.1 1 10 100 V , Drain-to-Source Voltage (V) V , Source-to-Drain Voltage (V) SD DS Fig 8. Maximum Safe Operating Area Fig 7. Typical Source-Drain Diode Forward Voltage 3.0 2.5 2.0 1.5 1.0 Fig 10a. Switching Time Test Circuit 0.5 0.0 A 25 50 75 100 125 150 T , Ambient Temperature (°C) A Fig 9. Maximum Drain Current Vs. Ambient Temperature Fig 10b. Switching Time Waveforms Fig 11b. Basic Gate Charge Waveform Fig 11a. Gate Charge Test Circuit 72 I , Drain Current (Amps) I , Reverse Drain Current (A) D SD I , Drain Current (A) D P-Channel IRF7106 100 100 VGS VGS TOP - 15V TOP - 15V - 10V - 10V - 8.0V - 8.0V - 7.0V - 7.0V - 6.0V - 6.0V - 5.5V - 5.5V - 5.0V - 5.0V BOTTOM - 4.5V BOTTOM - 4.5V 10 10 -4.5V -4.5V 1 1 20µs PULSE WIDTH 20µs PULSE WIDTH TJ = 150°C T = 25°C J A 0.1 0.1 A 0.1 1 10 100 0.1 1 10 100 -V , Drain-to-Source Voltage (V) -V , Drain-to-Source Voltage (V) DS DS Fig 12. Typical Output Characteristics, Fig 13. Typical Output Characteristics, o o T = 25 C T = 150 C J J 2.0 100 I D = -2.5A 1.5 T = 25°C J T = 150°C J 1.0 10 0.5 V = -15V DS V = -10V GS 20µs PULSE WIDTH 0.0 1 A A -60 -40 -20 0 20 40 60 80 100 120 140 160 4 6 8 10 T , Junction Temperature (°C) -V , Gate-to-Source Voltage (V) J GS Fig 15. Normalized On-Resistance Fig 14. Typical Transfer Characteristics Vs. Temperature 800 V = 0V, f = 1MHz GS 20 I = -2.3A C = C + C , C SHORTED D iss gs gd ds V = -10V C = C DS rss gd C = C + C oss ds gd 16 600 C oss 12 Ci ss 400 8 C rss 200 4 FOR TEST CIRCUIT 0 SEE FIGURE 22 A 0 A 1 10 100 0 4 8 12 16 20 -V , Drain-to-Source Voltage (V) DS Q , Total Gate Charge (nC) G Fig 16. Typical Capacitance Vs. Fig 17. Typical Gate Charge Vs. Drain-to-Source Voltage Gate-to-Source Voltage 73 C, Capacitance (pF) -I , Drain-to-Source Current (A) -I , Drain-to-Source Current (A) D D R , Drain-to-Source On Resistance DS(on) -I , Drain-to-Source Current (A) D (Normalized) -V , Gate-to-Source Voltage (V) GS IRF7106 P-Channel 100 10 OPERATION IN THIS AREA LIMITED BY R DS(on) T = 150°C J 10 T = 25°C J 1ms 1 10ms 1 100ms T = 25°C A T = 150°C J Single Pulse VG S = 0V 0.1 A 0.1 A 0.0 1.0 2.0 3.0 0.1 1 10 100 -V , Drain-to-Source Voltage (V) -V , Source-to-Drain Voltage (V) SD DS Fig 18. Typical Source-Drain Diode Fig 19. Maximum Safe Operating Area Forward Voltage 2.5 2.0 1.5 1.0 0.5 Fig 21a. Switching Time Test Circuit 0.0 A 25 50 75 100 125 150 T , Ambient Temperature (°C) A Fig 20. Maximum Drain Current Vs. Ambient Temperature Fig 21b. Switching Time Waveforms Fig 22b. Basic Gate Charge Waveform Fig 22a. Gate Charge Test Circuit 74 -I , Drain Current (Amps) -I , Reverse Drain Current (A) D SD -I , Drain Current (A) D N-P Channel IRF7106 100 D = 0.50 0.20 10 0.10 0.05 P DM 0.02 1 t 0.01 1 t SINGLE PULSE 2 (THERMAL RESPONSE) N otes: 1 . D uty factor D = t / t 1 2 2. P ea k T = P x Z + T J D M th JA A A 0.1 0.00001 0.0001 0.001 0.01 0.1 1 10 100 1000 t , Rectangular Pulse Duration (sec) 1 Fig 23. Maximum Effective Transient Thermal Impedance, Junction-to-Ambient Refer to the Appendix Section for the following: Appendix A: Figure 24, Peak Diode Recovery dv/dt Test Circuit — See page 329. Appendix B: Package Outline Mechanical Drawing — See page 332. Appendix C: Part Marking Information — See page 332. Appendix D: Tape and Reel Information — See page 336. 75 Thermal Response (Z ) thJA
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the IRF7106 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Manufacturers




What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods