INTERNATIONAL RECTIFIER IR3856W
Description
International Rectifier IR3856W Series SupIRBuck DC-DC Synchronous Buck Regulators
Part Number
IR3856W
Price
Request Quote
Manufacturer
INTERNATIONAL RECTIFIER
Lead Time
Request Quote
Category
PRODUCTS - I
Features
- -40oC to 125oC operating junction temperature
- 4mm x 5mm Power QFN Package
- Continuous 6A Load Capability
- Enable Input with Voltage Monitoring Capability
- Enhanced Pre-Bias Start-up
- Greater than 95% Maximum Efficiency
- Halogen Free, Lead Free and RoHS compliant
- Hiccup Current Limit
- High Bandwidth E/A for excellent transient performance
- Integrated Bootstrap-diode
- PGood output
- Precision Reference Voltage (0.7V, +/-1%)
- Programmable Over Current Protection
- Programmable Soft-Start
- Programmable Switching Frequency up to 1.5MHz
- Seq input for Tracking applications
- Thermal Protection
- Wide Input Voltage Range 1.5V to 16V
- Wide Output Voltage Range 0.7V to 0.9*Vin
Datasheet
International_Rectifier_IR3856W_SupIRBuck_DC-DC_Buck_Regulators_datasheet1-1726978522.pdf
1016 KiB
Extracted Text
PD-97506
IR3856WMPbF
TM
HIGHLY EFFICIENT
SupIRBuck
INTEGRATED 6A, SYNCHRONOUS BUCK REGULATOR
Features
Description
• Greater than 95% Maximum Efficiency
TM
The IR3856W SupIRBuck is an easy-to-use,
• Wide Input Voltage Range 1.5V to 16V
fully integrated and highly efficient DC/DC
• Wide Output Voltage Range 0.7V to 0.9*Vin
synchronous Buck regulator. The MOSFETs co-
• Continuous 6A Load Capability
packaged with the on-chip PWM controller make
• Integrated Bootstrap-diode
IR3856W a space-efficient solution, providing
• High Bandwidth E/A for excellent transient
accurate power delivery for low output voltage
performance
applications.
• Programmable Switching Frequency up to 1.5MHz
• Programmable Over Current Protection
IR3856W is a versatile regulator which offers
• PGood output
programmability of start up time, switching
• Hiccup Current Limit
frequency and current limit while operating in
• Precision Reference Voltage (0.7V, +/-1%)
wide input and output voltage range.
• Programmable Soft-Start
The switching frequency is programmable from
• Enable Input with Voltage Monitoring Capability
250kHz to 1.5MHz for an optimum solution.
• Enhanced Pre-Bias Start-up
• Seq input for Tracking applications It also features important protection functions,
o o
C to 125 C operating junction temperature
• -40 such as Pre-Bias startup, hiccup current limit and
• Thermal Protection
thermal shutdown to give required system level
• 4mm x 5mm Power QFN Package
security in the event of fault conditions.
• Halogen Free, Lead Free and RoHS compliant
Applications
• Server Applications • Netcom Applications
• Computing Peripheral Voltage Regulators
• Storage Applications
• General DC-DC Converters
• Embedded Telecom Systems
• Distributed Point of Load Power Architectures
Fig. 1. Typical application diagram
1
Rev 9.0
PD-97506
IR3856WMPbF
ABSOLUTE MAXIMUM RATINGS
(Voltages referenced to GND unless otherwise specified)
• Vin ……………………………………….……………. -0.3V to 25V
• PVcc, Vcc ……………….……..….……..……….…… -0.3V to 8V (Note2)
• Boot ……………………………………..……….…. -0.3V to 33V
• SW …………………………………………..……… -0.3V to 25V(DC), -4V to 25V(AC, 100ns)
• Boot to SW ……..…………………………….…..….. -0.3V to Vcc+0.3V (Note1)
• OCSet ………………………………………….……. -0.3V to 30V (Max 30mA)
• Input / output Pins ……………………………….. ... -0.3V to Vcc+0.3V (Note1)
• PGND to GND ……………...………………………….. -0.3V to +0.3V
• Storage Temperature Range ................................... -55°C To 150°C
• Junction Temperature Range ................................... -40°C To 150°C (Note2)
• ESD Classification …………………………… ……… JEDEC Class 1C
• Moisture sensitivity level………………...………………JEDEC Level 3@260 °C (Note5)
Note1: Must not exceed 8V
o o
Note2: Vcc must not exceed 7.5V for Junction Temperature between -10 C and -40 C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. These are stress ratings only and functional operation of the device at these or any other
conditions beyond those indicated in the operational sections of the specifications are not implied.
PACKAGE INFORMATION
4mm x 5mm POWER QFN
o *
θ = 45 C / W
JA
( Sync _ FET )
o *
11
θ = 45 C / W
12 JA
13 ( Ctrl _ FET )
o
SW
V
θ = 2 C / W
IN
J -PCB
PGnd
*
Exposed pads on underside
are connected to copper
pads of 4-layer (2 oz.) PCB
14 10 PVcc
Boot
board design
17
Enable V
15 9
CC
Gnd
PGood
Seq 16 8
1 4 7
23 5 6
Fb NC COMP Gnd Rt SS/SD OCSet
ORDERING INFORMATION
PACKAGE PACKAGE PIN COUNT PARTS PER
DESIGNATOR REEL
DESCRIPTION
M IR3856WMTRPbF 17 4000
M IR3856WMTR1PbF 17 750
2
Rev 9.0
PD-97506
IR3856WMPbF
Block Diagram
Fig. 2. Simplified block diagram of the IR3856W
3
Rev 9.0
PD-97506
IR3856WMPbF
Pin Description
Pin Name Description
1 Fb Inverting input to the error amplifier. This pin is connected directly to the
output of the regulator via resistor divider to set the output voltage and
provide feedback to the error amplifier.
2 NC No connect
3 Comp Output of error amplifier. An external resistor and capacitor network is
typically connected from this pin to Fb pin to provide loop
compensation.
4 Gnd Signal ground for internal reference and control circuitry.
5 Rt Set the switching frequency. Connect an external resistor from this pin
to Gnd to set the switching frequency.
6 SS/SD Soft start / shutdown. This pin provides user programmable soft-start
function. Connect an external capacitor from this pin to Gnd to set the
start up time of the output voltage. The converter can be shutdown by
pulling this pin below 0.3V.
7 OCSet Current limit set point. A resistor from this pin to SW pin will set the
current limit threshold.
8 PGood Power Good status pin. Output is open drain. Connect a pull up resistor
from this pin to Vcc.
9 V This pin powers the internal IC. A minimum of 1uF high frequency
CC
capacitor must be connected from this pin to Analog ground (AGnd).
10 PVcc This pin powers the drivers. A minimum of 1uF high frequency capacitor
must be connected from this pin to the power ground (PGnd).
11 PGnd Power Ground. This pin serves as a separated ground for the MOSFET
drivers and should be connected to the system’s power ground plane.
12 SW Switch node. This pin is connected to the output inductor.
13 V Input voltage connection pin.
IN
14 Boot Supply voltage for high side driver. A 0.1uF capacitor must be
connected from this pin to SW.
15 Enable Enable pin to turn on and off the device. Use two external resistors to
set the turn on threshold (see Enable section). Connect this pin to Vcc if
it is not used.
16 Seq Sequence pin. Use two external resistors to set Simultaneous Power up
sequencing. If this pin is not used connect to Vcc.
17 Gnd Signal ground for internal reference and control circuitry.
4
Rev 9.0
PD-97506
IR3856WMPbF
Recommended Operating Conditions
Symbol Definition Min Max Units
V Input Voltage 1.5 16
in
P V , V Supply Voltage 4.5 5.5
cc cc
V
Boot to SW Supply Voltage 4.5 5.5
V Output Voltage 0.7 0.9*Vin
o
I Output Current 0 6 A
o
Fs Switching Frequency 225 1650 kHz
o
T Junction Temperature -40 125 C
j
Electrical Specifications
Unless otherwise specified, these specification apply over 4.5V< PVcc=V <5.5V, V =12V
cc in
o o o
0 C
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the IR3856W have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Manufacturers




What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods