40 WATTS OUTPUT SPECIFICATIONS SRP-40A SERIES Features Total Output Power 40 W (33W, 1001) Output Voltage Output 1: +/-0.25% Centering(50% Load) Output 2: +/-5.00% Universal 85-264 VAC Input Output 3: +/-3.00% High Efficiency Output 4: +/-3.00% Advanced SMT Design (All outputs at 50% rated load) Compact 2.5" X 4.25" X 1.2" Size Source Regulation Outputs 1-4: 0.5% Class B Emissions Per EN 55022/11 Load Regulation (Local Sense) EMC to EN 61000-6-2 & EN 60601-1-2 Output 1:0.5% (10-100% Load 2 Year Warranty Change) Fits 1U Application (30-100% Output 2: 5.0% EN 60950 ITE Certification Load Change) (30-100% EN 60601-1 Medical Certification (2003, 4002) 7.0% Load Change) Optional Chassis & Cover (10-100% Output 3: 0.5% Load Change) (10-100% Output 4: 0.5% Load Change) Cross Regulation Output 2: 5.0% Output 3: 0.5% Output 4: 0.5% (Output 1 load varied 50-100%) Output Voltage Adjust Output 1: 95% to 105% Range Output Noise Outputs 1-4: 1% Turn On Overshoot None Transient Response Outputs 1-4 Volt. Deviation 5% Recovery Time 2 mS Load Change 50% To 100% Output Overvoltage Output 1: 110% to 150% Protection (Optional) Output Overpower Output 1&2 110% Min. Protection Outputs cycle on/off, auto recovery Output Overcurrent Output 3&4 110% Min. Protection Hold Up Time 10 mS Min, 40 W Output 120 V Input Start Up Time 1 Second INPUT SPECIFICATIONS ENVIRONMENTAL SPECIFICATIONS oo Source Voltage 85-264 Voltage AC 0 C to +70 C Derating: Ambient Operating Frequency Range 47-63 Hz See Power Rating Chart Temperature Range Source Current Ambient Storage oo -40 C to +85 C True RMS 1A At 85V Input Temperature Range Peak Inrush 30A o Outputs 1-4: 0.02%/ C Temperature Coefficient Efficiency .66 -.72 (Varies by model) Authorized Distributor: TRC Electronics, Inc. Tel: 973.779.8282 Fax: 973.779.1490 www.trcelectronics.com SAFETY SPECIFICATIONS GENERAL SPECIFICATIONS General Protection Class: I Dielectric Strength Reinforced Insulation5656 VDC, Primary to Secondary, 1 Sec. Overvoltage Category: II Basic Insulation2121 VDC, Primary to Ground, 1 Sec. Pollution Degree: 2 Operational Insulation 707 VDC, Secondary to Ground, 1 Sec. Underwriters UL 60950, Third Edition Leakage Current <300 ÂIA Earth Leakage Laboratories UL 2601 - 1 Second Current File E137708 Edition Mean Time Between 100,000 Hours min., CB Report Per IEC 950 o Failures MIL-HDBK-217F, 25 C, GB (1991) Weight 0.85 Lbs. Chassis and Second Edition A1, A2, A3, Cover A4 0.49 Lbs. Open Frame All EN 60950 Deviations ELECTROMAGNETIC COMPATIBILITY CB Report Per IEC Electrostatic EN 61000-4-2 +/-8kV Contact 601-1-1988 Discharge Discharge First Edition, A1, A2 +/-8kVAir UL Recognition CAN/CSA-C22.2 No. Discharge Mark for 60950:00 Radiated EN 61000-4-380MHz-2.5GHz, Canada CAN/CSA-C22.2 No. Electro-magnetic 10V/m, 80% AM File E137708 601-1-M90 Field TUV EN 60950/A11:1997 EFT/Bursts EN 61000-4-4 +/-2kV EN 60601-1/A2: 1995 Surges EN 61000-4-5 +/-1 kV Differential Low Voltage Directive Mode +/-2 kV Common Mode Conducted EN 61000-4-6 .15-80MHz., 10V, Notes Immunity 80% AM Consult factory for alternate output configuration. Voltage Dips and EN 30% Reduction Consult factory for positive, negative or floating Interruptions 61000-4-11 95% Reduction output 2 or 3. 60% Reduction Refer to Application Information for complete output power ratings. 95% Reduction All specifications are maximum at 25C unless Radiated EN 55011/22 Class B otherwise stated and are subjected to change Emissions without notice. Conducted EN 55011/22 Class B Specify optional chassis and cover when ordering. Emissions MODEL LISTING Model Output 1 Output 2 Output 3 Output 4 Max Power SRP-40A-4001 +3.3V/5A +5V/3A +12V/.7A -12V/.7A 40W SRP-40A-4002 +5V/5A +3.3V/3A +12V/.7A -12V/.7A 40W SRP-40A-4003 +5V/5A -5V/3A +12V/.7A -12V/.7A 40W SRP-40A-4004 +5V/5A -5V/3A +15V/.7A -15V/.7A 40W SRP-40A-4005 +5V/5A +24V/1.5A +12V/.7A -12V/.7A 40W SRP-40A-4006 +5V/5A +24V/1.5A +15V/.7A -15V/.7A 40W SRP-40A-3001 +5V/5A +12V/2A -12V/.7A 40W SRP-40A-3002 +5V/5A +15V/2A -15V/.7A 40W SRP-40A-2001 +5V/5A +24V/1.5A 40W SRP-40A-2002 +5V/5A +12V/3A 40W SRP-40A-2003 +5V/5A -5V/4A 40W SRP-40A-2004 +12V/3A -12V/3A 40W SRP-40A-2005 +15V/2.5A -15V/2A 40W SRP-40A-1001 3.3V/10A 33W SRP-40A-1002 5V/8A 40W SRP-40A-1003 12V/3.33A 40W SRP-40A-1004 15V/2.67A 40W SRP-40A-1005 24V/1.67A 40W SRP-40A-1006 48V/0.83A 40W Authorized Distributor: TRC Electronics, Inc. Tel: 973.779.8282 Fax: 973.779.1490 www.trcelectronics.com SRP-40A SERIES MECHANICAL SPECIFICATIONS Authorized Distributor: TRC Electronics, Inc. Tel: 973.779.8282 Fax: 973.779.1490 www.trcelectronics.com Authorized Distributor: TRC Electronics, Inc. Tel: 973.779.8282 Fax: 973.779.1490 www.trcelectronics.com APPLICATIONS INFORMATION Each output can deliver its rated current but This power supply has been safety approved 1. 11. total output power must not exceed and final tested using a DC 40 watts(33W, 1001). dielectric strength test. Please consult factory Maximum ambient temperature is reduced to 40 before performing AC dielectric strength test. 2. C with optional chassis and cover. Semiconductor case temperature must not Maximum Output Power vs. Ambient 3. Temperature exceed 110 C Sufficient area must be provided around 4. convection cooled power supplies to allow natural movement of air develop. This product is intended for use as a 5. professionally installed component within information technology and medical equipment. A minimum load of 10% is required on output 6. one to insure proper regulation of remaining outputs. Remote sense terminals may be used to 7. compensate for cable losses up to 250mV. The use of a twisted pair is recommended as well as a decoupling capacitor (0.1 0 10microF) and a capacitor of 100microF/amp connected across CONNECTOR SPECIFICATIONS the load. .156 friction lock header mates 8. Peak to peak output ripple and noise is with Molex 09-50-3031 or measured directly at the output equivalent crimp terminal terminals of the power supply, without the use P1 AC Input housing with Molex of the probe ground lead or retractable tip, 20 08-50-0189 or equivalent MHz bandwidth. crimp terminal. 9. This product is use only one fuse in the input .156 friction lock header mates circuit. In consideration of clause 57.6 of UL with Molex 09-50-3061 or 2601-1, a second fuse may be required in the DC equivalent crimp terminal end product. P3 Output(Single) housing with Molex 10. This product was type tested and safety 08-50-0189 or equivalent certificated using the the dielectric strength test crimp terminal. voltages listed in Table V of UL 60601-1. In .156 friction lock header mates consideration of clause 20.4g, care must be with Molex 09-50-3081 or taken to insure the voltage applied to a DC equivalent crimp terminal reinforced insulation does not over stress basic P3 Output(Multiple) housing with Molex insulation. Secondary to ground capacitors may 08-50-0189 or equivalent need to be removed prior to performing a crimp terminal. dielectric strength type test on the end product. .100 friction lock header mates It is highly recommended that the DC test with Molex 22-01-2027 or voltages listed in DVB.1. Annex DVB are not Sense equivalent crimp terminal exceeded during a production-line dielectric P4,5 housing with Molex strength test of the assembled end product. 08-50-01114 or equivalent Please consult factory for further information. crimp terminal. G Ground .187 quick disconnect terminal. RECOMMENDED AIR FLOW DIRECTION Optimum 1. Good 2. Fair 3. Authorized Distributor: TRC Electronics, Inc. Tel: 973.779.8282 Fax: 973.779.1490 www.trcelectronics.com