Intel® Desktop Board D510MO Technical Product Specification October 2011 Order Number: E74523-002 ® The Intel Desktop Board D510MO may contain design defects or errors known as errata that may cause the product to deviate from published specifications. Current characterized errata are documented in the Intel Desktop Board D510MO Specification Update. Revision History Revision Revision History Date ® 001 First release of the Intel Desktop Board D510MO Technical Product December 2009 Specification. 002 Specification Changes October 2011 ® This product specification applies to only the standard Intel Desktop Board D510MO with BIOS identifier MOPNV10J.86A. ® INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS OTHERWISE AGREED IN WRITING BY INTEL, THE INTEL PRODUCTS ARE NOT DESIGNED NOR INTENDED FOR ANY APPLICATION IN WHICH THE FAILURE OF THE INTEL PRODUCT COULD CREATE A SITUATION WHERE PERSONAL INJURY OR DEATH MAY OCCUR. Intel Corporation may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights. Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. ® Intel Desktop Boards may contain design defects or errors known as errata, which may cause the product to deviate from published specifications. Current characterized errata are available on request. Contact your local Intel sales office or your distributor to obtain the latest specifications before placing your product order. Intel, the Intel logo, and Intel Atom are trademarks of Intel Corporation in the United States and/or other countries. * Other names and brands may be claimed as the property of others. Copyright © 2009-2011, Intel Corporation. All rights reserved. Board Identification Information Basic Desktop Board D510MO Identification Information AA Revision BIOS Revision Notes E76523-302 MOPNV10J.86A.0115 1,2 E76523-400 MOPNV10J.86A.0148 1,2 E76523-401 MOPNV10J.86A.0154 1,2 E76523-402 MOPNV10J.86A.0175 1,2 E76523-403 MOPNV10J.86A.0175 1,2 E76523-404 MOPNV10N.86A.0400 1,2 E76523-405 MOPNV10N.86A.0516 1,2 E76523-406 MOPNV10N.86A.0516 1,2 E76525-301 MOPNV10J.86A.0115 1,2 E76525-400 MOPNV10J.86A.0148 1,2 E76525-401 MOPNV10J.86A.0154 1,2 E76525-402 MOPNV10J.86A.0175 1,2 E76525-403 MOPNV10J.86A.0175 1,2 E76525-404 MOPNV10N.86A.0400 1,2 E76525-405 MOPNV10N.86A.0516 1,2 E76525-406 MOPNV10N.86A.0516 1,2 E67982-303 MOPNV10J.86A.0115 1,2 E67982-400 MOPNV10J.86A.0148 1,2 E67982-401 MOPNV10J.86A.0154 1,2 E67982-402 MOPNV10J.86A.0175 1,2 E67982-403 MOPNV10J.86A.0175 1,2 E67982-404 MOPNV10N.86A.0400 1,2 E67982-405 MOPNV10N.86A.0516 1,2 E67982-406 MOPNV10N.86A.0516 1,2 Notes: 1. The AA number is found on a small label on the component side of the board. 2. The CG82NM10 Express Chipset used on this AA revision consists of the following component: Device Stepping S-Spec Numbers CG82NM10 B0 SLGXX iii Intel Desktop Board D510MO Technical Product Specification Specification Changes or Clarifications Table 1 indicates the Specification Changes or Specification Clarifications that apply to ® the Intel Desktop Board D510MO. Table 1. Specification Changes or Clarifications Date Type of Change Description of Changes or Clarifications • Updated Table 34: October 2011 Spec Clarification ― Deleted “2.5-inch SATA hard disk drive” ― Changed the Maximum Load Configuration to 3.825 A for Current Draw at 12 V and 45.9 W for Power Consumption Errata Current characterized errata, if any, are documented in a separate Specification Update. See http://developer.intel.com/products/desktop/motherboard/index.htm for the latest documentation. iv Preface This Technical Product Specification (TPS) specifies the board layout, components, ® connectors, power and environmental requirements, and the BIOS for the Intel Desktop Board D510MO. It describes the standard product and available manufacturing options. Intended Audience The TPS is intended to provide detailed, technical information about the Intel Desktop Board D510MO and its components to the vendors, system integrators, and other engineers and technicians who need this level of information. It is specifically not intended for general audiences. What This Document Contains Chapter Description 1 A description of the hardware used on the board 2 A map of the resources of the board 3 The features supported by the BIOS Setup program 4 A description of the BIOS error messages, beep codes, and POST codes 5 Regulatory compliance and battery disposal information Typographical Conventions This section contains information about the conventions used in this specification. Not all of these symbols and abbreviations appear in all specifications of this type. Notes, Cautions, and Warnings NOTE Notes call attention to important information. CAUTION Cautions are included to help you avoid damaging hardware or losing data. v Intel Desktop Board D510MO Technical Product Specification Other Common Notation # Used after a signal name to identify an active-low signal (such as USBP0#) GB Gigabyte (1,073,741,824 bytes) GB/sec Gigabytes per second Gbit Gigabit (1,073,741,824 bits) KB Kilobyte (1024 bytes) Kbit Kilobit (1024 bits) kbits/sec 1000 bits per second MB Megabyte (1,048,576 bytes) MB/sec Megabytes per second Mbit Megabit (1,048,576 bits) Mbit/sec Megabits per second xxh An address or data value ending with a lowercase h indicates a hexadecimal value. x.x V Volts. Voltages are DC unless otherwise specified. * This symbol is used to indicate third-party brands and names that are the property of their respective owners. vi Contents 1 Product Description 1.1 Overview........................................................................................ 11 1.1.1 Feature Summary ................................................................ 11 1.1.2 Board Layout....................................................................... 13 1.1.3 Block Diagram ..................................................................... 15 1.2 Online Support................................................................................ 16 1.3 Processor ....................................................................................... 16 1.3.1 Intel D510 Graphics Subsystem.............................................. 17 1.4 System Memory .............................................................................. 18 ® 1.5 Intel NM10 Express Chipset............................................................. 19 1.5.2 USB ................................................................................... 21 1.5.3 SATA Support ...................................................................... 21 1.6 Real-Time Clock Subsystem .............................................................. 22 1.7 Legacy I/O Controller....................................................................... 22 1.7.1 Serial Port Headers............................................................... 22 1.7.2 Parallel Port Header.............................................................. 23 1.8 LAN Subsystem............................................................................... 23 1.8.1 LAN Subsystem Drivers......................................................... 23 1.8.2 RJ-45 LAN Connector with Integrated LEDs .............................. 24 1.9 Audio Subsystem............................................................................. 25 1.9.1 Audio Subsystem Software .................................................... 26 1.9.2 Audio Connectors and Headers............................................... 26 1.10 Hardware Management Subsystem .................................................... 27 1.10.1 Hardware Monitoring............................................................. 27 1.10.2 Thermal Monitoring .............................................................. 28 1.11 Power Management ......................................................................... 29 1.11.1 ACPI................................................................................... 29 1.11.2 Hardware Support ................................................................ 32 1.11.3 ENERGY STAR*, E-Standby, and EuP Compliance...................... 35 2 Technical Reference 2.1 Memory Map................................................................................... 37 2.1.1 Addressable Memory............................................................. 37 2.2 Connectors and Headers................................................................... 40 2.2.1 Back Panel .......................................................................... 41 2.2.2 Component-side Connectors and Headers ................................ 43 2.3 BIOS Configuration Jumper Block....................................................... 54 2.4 Mechanical Considerations ................................................................ 56 2.4.1 Form Factor......................................................................... 56 2.5 Electrical Considerations................................................................... 57 2.5.1 Fan Header Current Capability................................................ 57 2.5.2 Add-in Board Considerations .................................................. 57 vii Intel Desktop Board D510MO Technical Product Specification 2.6 Thermal Considerations.................................................................... 57 2.6.1 Passive Heatsink Design in a Passive System Environment ......... 59 2.7 Power Consumption ......................................................................... 62 2.7.1 Minimum Load Configuration.................................................. 62 2.7.2 Maximum Load Configuration ................................................. 62 2.8 Reliability ....................................................................................... 63 2.9 Environmental ................................................................................ 64 3 Overview of BIOS Features 3.1 Introduction ................................................................................... 65 3.2 BIOS Flash Memory Organization....................................................... 66 3.3 Resource Configuration .................................................................... 66 3.3.1 PCI* Autoconfiguration.......................................................... 66 3.4 System Management BIOS (SMBIOS)................................................. 67 3.5 Legacy USB Support ........................................................................ 68 3.6 BIOS Updates ................................................................................. 69 3.6.1 BIOS Recovery..................................................................... 69 3.6.2 Custom Splash Screen .......................................................... 70 3.7 Boot Options................................................................................... 70 3.7.1 CD-ROM Boot ...................................................................... 70 3.7.2 Network Boot....................................................................... 70 3.7.3 Booting Without Attached Devices........................................... 71 3.7.4 Changing the Default Boot Device During POST ........................ 71 3.8 BIOS Security Features .................................................................... 72 4 Board Status and Error Messages 4.1 BIOS Beep Codes ............................................................................ 73 4.2 Front-panel Power LED Blink Codes.................................................... 74 4.3 BIOS Error Messages ....................................................................... 74 4.4 Port 80h POST Codes ....................................................................... 75 5 Regulatory Compliance and Battery Disposal Information 5.1 Regulatory Compliance..................................................................... 81 5.1.1 Safety Standards.................................................................. 81 5.1.2 European Union Declaration of Conformity Statement................ 82 5.1.3 Product Ecology Statements................................................... 83 5.1.4 EMC Regulations .................................................................. 87 5.1.5 Product Certification Markings (Board Level)............................. 88 5.2 Battery Disposal Information............................................................. 89 viii Contents Figures 1. Major Board Components.................................................................. 13 2. Block Diagram................................................................................ 15 3. LAN Connector LED Locations............................................................ 24 4. Back Panel Audio Connectors ............................................................ 26 5. Thermal Sensors and Fan Header....................................................... 28 6. Location of the Standby Power Indicator LED....................................... 34 7. Detailed System Memory Address Map ............................................... 38 8. Back Panel Connectors ..................................................................... 41 9. I/O Shield Reference Diagram ........................................................... 42 10. Component-side Connectors and Headers ........................................... 43 11. Connection Diagram for Front Panel Header ........................................ 51 12. Connection Diagram for Front Panel USB Header.................................. 53 13. Connection Diagram for Front Panel USB Header (with Intel Z-U130 USB Solid-State Drive, or Compatible Device, Support)......................... 53 14. Location of the BIOS Configuration Jumper Block ................................. 54 15. Board Dimensions........................................................................... 56 16. Localized High Temperature Zones..................................................... 58 17. Fan Location Guide for Cassis Selection (Chassis Orientation is Not Restricted)................................................................................ 61 Tables 1. Feature Summary............................................................................ 11 2. Board Components Shown in Figure 1-1 ............................................. 14 3. Supported Memory Configurations ..................................................... 18 4. LAN Connector LED States................................................................ 24 5. Audio Jack Support.......................................................................... 25 6. Effects of Pressing the Power Switch .................................................. 29 7. Power States and Targeted System Power........................................... 30 8. Wake-up Devices and Events ............................................................ 31 9. ENERGY STAR Requirements............................................................. 35 10. System Memory Map ....................................................................... 39 11. Component-side Connectors and Headers Shown in Figure 2-4............... 44 12. Serial Port Header (COM 1 and COM 2)............................................... 45 13. LVDS Data Connector (30-Pin) .......................................................... 45 14. LVDS Panel Voltage Selection Jumper................................................. 46 15. Chassis Fan Header ......................................................................... 46 16. SATA Connectors............................................................................. 46 17. LVDS Inverter Power Connector......................................................... 47 18. LVDS Inverter Power Voltage Selection Jumper.................................... 47 19. Parallel Port Header ......................................................................... 48 20. Front Panel Wireless Activity LED Header ............................................ 48 21. S/PDIF Header................................................................................ 48 22. Front Panel Audio Header for Intel HD Audio........................................ 49 23. Front Panel Audio Header for AC ’97 Audio .......................................... 49 ix Intel Desktop Board D510MO Technical Product Specification 24. Front Panel USB Header ................................................................... 49 25. Front Panel USB Header (with Intel Z-U130 USB Solid-State Drive, or Compatible Device, Support)......................................................... 49 26. Power Connector............................................................................. 50 27. Front Panel Header .......................................................................... 51 28. States for a One-Color Power LED...................................................... 52 29. BIOS Configuration Jumper Settings................................................... 55 30. Fan Header Current Capability........................................................... 57 31. Thermal Considerations for Components ............................................. 59 32. Minimum Load Configuration Current and Power Results ....................... 62 33. Maximum Load Configuration Current and Power Results....................... 63 34. Intel Desktop Board D510MO Environmental Specifications.................... 64 35. BIOS Setup Program Menu Bar.......................................................... 66 36. BIOS Setup Program Function Keys.................................................... 66 37. Acceptable Drives/Media Types for BIOS Recovery ............................... 69 38. Boot Device Menu Options ................................................................ 71 39. Supervisor and User Password Functions............................................. 72 40. BIOS Beep Codes ............................................................................ 73 41. Front-panel Power LED Blink Codes.................................................... 74 42. BIOS Error Messages ....................................................................... 74 43. Port 80h POST Code Ranges.............................................................. 75 44. Port 80h POST Codes ....................................................................... 76 45. Typical Port 80h POST Sequence........................................................ 79 46. Safety Standards............................................................................. 81 47. Lead-Free Board Markings ................................................................ 86 48. EMC Regulations............................................................................. 87 49. Product Certification Markings ........................................................... 88 x 1 Product Description 1.1 Overview 1.1.1 Feature Summary Table 2 summarizes the major features of Intel Desktop Board D510MO. Table 2. Feature Summary Form Factor Mini-ITX, (6.7 inches by 6.7 inches [170 millimeters by 170 millimeters]) compatible with microATX ® Processor Passively-cooled, soldered-down Dual-Core Intel Atom™ processor with integrated graphics and integrated memory controller • Two 240-pin DDR2 SDRAM Dual Inline Memory Module (DIMM) sockets Memory • Support for DDR2 800 MHz and DDR2 667 MHz DIMMs • Support for up to 2 GB of system memory on a single DIMM (4 GB with two DIMMs) ® • Passively cooled, Intel NM10 Express Chipset Chipset Audio Multi-streaming 4+2 channel audio subsystem support based on the Realtek* ALC662 high definition audio codec ® Internal Graphics Onboard Intel graphics subsystem with support for: • Integrated GMCH • Analog displays (VGA) • Flat Panel displays (optional LVDS interface) Legacy I/O Control Winbond W83627THG-I based Legacy I/O controller for hardware management, serial, parallel, and PS/2* ports • Seven USB 2.0 ports: Peripheral ― Four back panel ports Interfaces ― Three front panel ports (via two internal headers; one header (with one ® port) supports an Intel Z-U130 USB Solid-State Drive (or compatible device) • Two Serial ATA (SATA) 3.0 Gb/s connectors (supporting IDE and AHCI) • One parallel port header • Two serial port headers • PS/2*-style keyboard and mouse ports LAN Support 10/100/1000 Mbits/sec LAN subsystem using a Realtek 8111DL Gigabit Ethernet Controller continued 11 Intel Desktop Board D510MO Technical Product Specification Table 2. Feature Summary (continued) ® • Intel BIOS (resident in the SPI Flash device) BIOS • Support for Advanced Configuration and Power Interface (ACPI), Plug and Play, and SMBIOS • Support for PCI* Local Bus Specification Revision 2.3 Instantly Available PC Technology • Suspend to RAM support • Wake on PCI, PCI Express*, PS/2, serial, front panel, USB ports, and LAN • One PCI Conventional bus connector Expansion Capabilities • PCI Express x1 Mini Card connector • Hardware monitoring through the Windbond I/O controller Hardware Monitor Subsystem • Voltage sense to detect out of range power supply voltages • Thermal sense to detect out of range thermal values • One fan header • One fan sense input used to monitor fan activity • Fan speed control 12 Product Description 1.1.2 Board Layout Figure 1 shows the location of the major components. Figure 1. Major Board Components Table 3 lists the components identified in Figure 1. 13 Intel Desktop Board D510MO Technical Product Specification Table 3. Board Components Shown in Figure 1 Item/callout from Figure 1 Description Back panel connectors A B Serial port header (COM 1) C Parallel port header D Serial port header (COM 2) E LVDS inverter power voltage selection jumper (optional) Chassis fan header F G Power connector (2 x 12) H LVDS inverter power connector (optional) I Standby power LED J Intel Atom processor LVDS inverter panel voltage selection header (optional) K DIMM channel A socket, DIMM 0 L M DIMM channel A socket, DIMM 1 N LVDS panel connector (optional) O SATA connector 1 P SATA connector 0 Front panel header Q R Battery S Front panel wireless activity LED header T Intel NM10 Express Chipset U Front panel USB header (with Intel Z-U130 USB Solid-State Drive (or compatible device) support V PCI conventional bus connector W PCI Express x1 Mini Card connector USB front panel header X Front panel audio header Y Z BIOS setup configuration jumper block AA S/PDIF header 14 Product Description 1.1.3 Block Diagram Figure 2 is a block diagram of the major functional areas. Figure 2. Block Diagram 15 Intel Desktop Board D510MO Technical Product Specification 1.2 Online Support To find information about… Visit this World Wide Web site: Intel Desktop Board D510MO http://www.intel.com/products/motherboard/510MO/index.htm Desktop Board Support http://www.intel.com/support/motherboards/desktop Available configurations for the Intel http://www.intel.com/products/motherboard/D510MO/index.htm Desktop Board D510MO Chipset information http://www.intel.com/products/desktop/chipsets/index.htm BIOS and driver updates http://downloadcenter.intel.com Integration information http://www.intel.com/support/go/buildit Tested memory http://www.intel.com/support/motherboards/desktop/sb/CS- 025414.htm 1.3 Processor The board has a passively-cooled, soldered-down Dual-Core Intel Atom processor with integrated graphics and integrated memory controller. NOTE The board is designed to be passively cooled in a properly ventilated chassis. Chassis venting locations are recommended above the processor heatsink area for maximum heat dissipation effectiveness. For information about Refer to Power supply connectors Section 2.2.2.3, page 50 16 Product Description 1.3.1 Intel D510 Graphics Subsystem ® 1.3.1.1 Intel Graphics Media Accelerator 3150 Graphics Controller The Intel GMA 3150 graphics controller features the following: • 400 MHz core frequency • High quality texture engine ⎯ DX9.0c* and OpenGL* 1.4 compliant ⎯ Hardware Pixel Shader 2.0 ⎯ Vertex Shader Model 2.0 • 3D Graphics Rendering enhancements ⎯ 1.6 dual texture GigaPixel/s max fill rate ⎯ 16-bit and 32-bit color ⎯ Vertex cache • Video ⎯ Software DVD at 30 fps full screen ⎯ DVMT support up to 256 MB • Display ⎯ Supports analog displays up to 2048 x 1536 at 75 Hz refresh (QXGA) ⎯ Optionally supports LVDS display up to 1366 x 768 (single channel, 18 bpp) ⎯ Dual independent display support with LVDS option For information about Refer to Obtaining graphics software and utilities Section 1.2, page 16 17 Intel Desktop Board D510MO Technical Product Specification 1.4 System Memory The board has two 240-pin DDR2 DIMM sockets and supports the following memory features: • DDR2 SDRAM DIMMs with gold-plated contacts • Unbuffered, single-sided or double-sided DIMMs • 4 GB maximum total system memory • Minimum total system memory: 256 MB • Non-ECC DIMMs • Serial Presence Detect • DDR2 800 MHz and DDR2 667 MHz DIMMs NOTE Due to passively-cooled thermal constraints, system memory must have an operating o temperature rating of 85 C. The board is designed to be passively cooled in a properly ventilated chassis. Chassis venting locations are recommended above the system memory area for maximum heat dissipation effectiveness. NOTE To be fully compliant with all applicable DDR2 SDRAM memory specifications, the board should be populated with DIMMs that support the Serial Presence Detect (SPD) data structure. This allows the BIOS to read the SPD data and program the chipset to accurately configure memory settings for optimum performance. If non-SPD memory is installed, performance and reliability may be impacted or the DIMMs may not function under the determined frequency. Table 4 lists the supported DIMM configurations. Table 4. Supported Memory Configurations DIMM SDRAM SDRAM Organization Number of SDRAM Capacity Configuration Density Front-side/Back-side Devices 256 MB SS 256 Mbit 32 M x 8/empty 8 256 MB SS 512 Mbit 32 M x 16/empty 4 512 MB DS 256 Mbit 32 M x 8/32 M x 8 16 512 MB SS 512 Mbit 64 M x 8/empty 8 512 MB SS 1 Gbit 64 M x 16/empty 4 1024 MB DS 512 Mbit 64 M x 8/64 M x 8 16 1024 MB SS 1 Gbit 128 M x 8/empty 8 2048 MB DS 1 Gbit 128 M x 8/128 M x 8 16 Note: In the second column, “DS” refers to double-sided memory modules (containing two rows of SDRAM) and “SS” refers to single-sided memory modules (containing one row of SDRAM). 18 Product Description ® 1.5 Intel NM10 Express Chipset The Intel NM10 Express Chipset provides interfaces to the processor and the USB, SATA, LPC, LAN, PCI, and PCIe interfaces. The Intel NM10 Express Chipset is a centralized controller for the board’s I/O paths. NOTE The board is designed to be passively cooled in a properly ventilated chassis. Chassis venting locations are recommended above the processor heatsink area for maximum heat dissipation effectiveness. For information about Refer to The Intel NM10 Express chipset http://www.intel.com/products/desktop/chipsets/index.htm Resources used by the chipset Chapter 2 1.5.1.1 Video Memory Allocation Video memory is allocated from the total available system memory for the efficient balancing of 2-D/3-D graphics performance and overall system performance. Dynamic allocation of system memory to video memory is as follows: • 256 MB total RAM results in 32 MB video RAM • 512 MB total RAM results in 64 MB video RAM • 1 GB total RAM results in 128 MB video RAM • 2 GB total RAM results in 224 MB video RAM 1.5.1.2 Analog Display (VGA) The VGA port supports analog displays. The maximum supported resolution is 2048 x 1536 (QXGA) at a 75 Hz refresh rate. 1.5.1.3 Optional Flat Panel Interface (LVDS) The optional flat panel interface (LVDS) supports the following: • Panel support up to UXGA (1366 x 768) • 25 MHz to 112 MHz single–channel; @18 bpp ⎯ TFT panel type • Panel fitting, panning, and center mode • CPIS 1.5 compliant • Spread spectrum clocking • Panel power sequencing • Integrated PWM interface for LCD backlight inverter control 19 Intel Desktop Board D510MO Technical Product Specification 1.5.1.4 Configuration Modes For monitors attached to the VGA port, video modes supported by this board are based on the Extended Display Identification Data (EDID) protocol. Video mode configuration for LVDS displays is supported as follows: • Automatic panel identification via Extended Display Identification Data (EDID) for LVDS panels supporting EDID protocol. • Manual LVDS panel configuration through the BIOS setup page. This feature allows the manual entry of critical panel settings (equivalent to the 18-byte Detailed Timings Descriptor structure defined by the VESA EDID specification) for non-EDID panel support. In addition, BIOS setup provides the following configuration parameters for LVDS displays: • Screen Brightness: allows the end-user to set screen brightness for the display. • Maintain Aspect Ratio: allows the end-user to select whether the native aspect ratio is to be preserved during POST and before the video driver is loaded. • LVDS Configuration Changes: allows the system integrator to “lock” critical settings of the LVDS configuration to avoid end-users potentially rendering the display unusable (refer to Note 1). • Inverter Frequency and Polarity: allows the system integrator to set the operating frequency and polarity of the panel inverter board. • Minimum Inverter Current Limit (%): allows the system integrator to set minimum PWM%, as appropriate, according to the power requirements of the LVDS display and the selected inverter board. NOTE Support for LVDS configuration complies with the following: ® 1. “Unlocking” of critical settings of the LVDS configuration is supported via Intel Integrator Toolkit’s command-line tool. 2. Critical settings of the LVDS configuration are not exposed through Intel Integrator ® Toolkit or Intel Integrator Assistant GUIs. 3. Critical settings of the LVDS configuration will not be overwritten by loading BIOS setup defaults. 4. Critical settings of the LVDS configuration will be preserved across BIOS updates. 20 Product Description 1.5.2 USB The board provides up to seven USB 2.0 ports, supports UHCI and EHCI, and uses UHCI- and EHCI-compatible drivers. The port arrangement is as follows: • Four ports are implemented with stacked back panel connectors • Three front panel ports (via two internal headers; one header (with one port) ® supports an Intel Z-U130 USB Solid-State Drive (or compatible device) NOTE One of the front panel USB headers supports an Intel Z-U130 USB Solid-State Drive (or compatible device). Computer systems that have an unshielded cable attached to a USB port may not meet FCC Class B requirements, even if no device is attached to the cable. Use shielded cable that meets the requirements for full-speed devices. For information about Refer to The location of the USB connectors on the back panel Figure 8, page 41 The location of the front panel USB headers Figure 10, page 43 1.5.3 SATA Support The board provides two SATA interface connectors that support one device per connector. The board’s SATA controller offers independent SATA ports with a theoretical maximum transfer rate of 3.0 Gbits/sec on each port. One device can be installed on each port for a maximum of two SATA devices. A point-to-point interface is used for host to device connections, unlike PATA which supports a master/slave configuration and two devices on each channel. For compatibility, the underlying SATA functionality is transparent to the operating system. The SATA controller supports IDE and AHCI configuration and can operate in both legacy and native modes. In legacy mode, standard ATA I/O and IRQ resources are assigned (IRQ 14 and 15). In Native mode, standard PCI Conventional bus resource steering is used. Native mode is the preferred mode for configurations using the Windows* XP and Windows Vista* operating systems. For information about Refer to Obtaining AHCI driver Section 1.2, page 16 The location of the SATA connectors Figure 10, page 43 21 Intel Desktop Board D510MO Technical Product Specification 1.6 Real-Time Clock Subsystem A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years. When the computer is plugged in, the standby current from the power supply extends the life of the battery. The clock is accurate to ± 13 minutes/year at 25 ºC with 3.3 VSB applied. NOTE If the battery and AC power fail, custom defaults, if previously saved, will be loaded into CMOS RAM at power-on. When the voltage drops below a certain level, the BIOS Setup program settings stored in CMOS RAM (for example, the date and time) might not be accurate. Replace the battery with an equivalent one. Figure 1 on page 13 shows the location of the battery. 1.7 Legacy I/O Controller The Legacy I/O Controller provides the following features: • Two serial port headers • One parallel port header with Extended Capabilities Port (ECP) and Enhanced Parallel Port (EPP) support • Serial IRQ interface compatible with serialized IRQ support for PCI Conventional bus systems • PS/2-style keyboard and mouse ports • Intelligent power management, including a programmable wake-up event interface • PCI Conventional bus power management support The BIOS Setup program provides configuration options for the Legacy I/O controller. 1.7.1 Serial Port Headers The serial port headers, COM 1 and COM 2, are implemented as two 10-pin headers on the board. The serial port headers support data transfers at speeds up to 115.2 kbits/s with BIOS support. For information about Refer to The location of the serial port headers Figure 10, page 43 22 Product Description 1.7.2 Parallel Port Header The parallel port header is implemented as a 26-pin header on the board. Use the BIOS Setup program to set the parallel port mode. For information about Refer to The location of the parallel port header Figure 10, page 43 1.8 LAN Subsystem The LAN subsystem consists of the following: • Intel NM10 Express Chipset • Realtek 8111DL Gigabit Ethernet Controller for 10/100/1000 Mbits/sec Ethernet LAN connectivity • RJ-45 LAN connector with integrated status LEDs Additional features of the LAN subsystem include: • CSMA/CD protocol engine • LAN connect interface that supports the ethernet controller • PCI Conventional bus power management ⎯ Supports ACPI technology ⎯ Supports LAN wake capabilities 1.8.1 LAN Subsystem Drivers LAN drivers are available from Intel’s World Wide Web site. For information about Refer to Obtaining LAN drivers Section 1.2, page 16 23 Intel Desktop Board D510MO Technical Product Specification 1.8.2 RJ-45 LAN Connector with Integrated LEDs Two LEDs are built into the RJ-45 LAN connector (shown in Figure 3). Figure 3. LAN Connector LED Locations Table 5 describes the LED states when the board is powered up and the 10/100/1000 Mbits/sec LAN subsystem is operating. Table 5. LAN Connector LED States LED Color State Condition Green Blinking LAN activity occurring Activity (A) N/A Off 10 Mb/s data rate Speed (B) Green On 100 Mb/s data rate Yellow On 1000 Mb/s data rate 24 Product Description 1.9 Audio Subsystem The board supports the Intel High Definition Audio subsystem. The audio subsystem consists of the following: • Intel NM10 Express Chipset • Realtek ALC662 audio codec The audio subsystem has the following features: • Advanced jack sense for the back panel audio jacks that enables the audio codec to recognize the device that is connected to an audio port. The back panel audio jacks are capable of retasking according to the user’s definition, or can be automatically switched depending on the recognized device type. • Front panel Intel HD Audio and AC ’97 audio support • 3-port analog audio out stack • Internal S/PDIF out header • Windows Vista Basic certification • A signal-to-noise (S/N) ratio of 95 dB • Independent 5.1 audio playback from back panel connectors and stereo playback from the Intel High Definition Audio front panel header. • 4+2 channel in multi-streaming mode Table 6 lists the supported functions of the front panel and back panel audio jacks. Table 6. Audio Jack Support Line/ Center/ Audio Jack Line In Front Out Rear Out LFE MIC Headphones Front panel – Green No Yes No No No Yes Front panel – Pink No No No No Yes No Back panel – Blue Yes No Yes No No No Back panel – Green No Yes No No No Yes Back panel – Pink No No No Yes Yes No 25 Intel Desktop Board D510MO Technical Product Specification 1.9.1 Audio Subsystem Software Audio software and drivers are available from Intel’s World Wide Web site. For information about Refer to Obtaining audio software and drivers Section 1.2, page 16 1.9.2 Audio Connectors and Headers The board contains audio connectors and headers on both the back panel and the component side of the board. The component-side audio headers include the following: • Front panel audio (a 2 x 5-pin header that provides mic in and line out signals for front panel audio connectors) • S/PDIF audio 1 x 3-pin header Item Description A Line in B Line out C Mic in Figure 4. Back Panel Audio Connectors NOTE The back panel audio line out connector is designed to power headphones or amplified speakers only. Poor audio quality occurs if passive (non-amplified) speakers are connected to this output. For information about Refer to The locations of the front panel audio header and S/PDIF audio header Figure 10, page 43 The signal names of the front panel audio header and S/PDIF header Section 2.2.2.1. page 45 The back panel audio connectors Figure 4. page 26 26 Product Description 1.10 Hardware Management Subsystem The hardware management features enable the board to be compatible with the Wired for Management (WfM) specification. The board has several hardware management features, including the following: • Thermal and voltage monitoring • Chassis intrusion detection 1.10.1 Hardware Monitoring The hardware monitoring and fan control subsystem is based on the Winbond W83627THG-I device, which supports the following: • Processor and system ambient temperature monitoring • Chassis fan speed monitoring • Power monitoring of +12 V, +5 V, +5 Vstdby, +3.3 V, and +VCCP • SMBus interface 27 Intel Desktop Board D510MO Technical Product Specification 1.10.2 Thermal Monitoring Figure 5 shows the locations of the thermal sensors and fan header. Item Description A Chassis fan header B Thermal diode, located on the processor die C Remote thermal sensor Figure 5. Thermal Sensors and Fan Header 28 Product Description 1.11 Power Management Power management is implemented at several levels, including: • Software support through Advanced Configuration and Power Interface (ACPI) • Hardware support: ⎯ Power connector ⎯ Fan header ⎯ LAN wake capabilities ⎯ Instantly Available PC technology ⎯ Wake from USB ⎯ Wake from PS/2 devices ⎯ Power Management Event signal (PME#) wake-up support ⎯ WAKE# signal wake-up support 1.11.1 ACPI ACPI gives the operating system direct control over the power management and Plug and Play functions of a computer. The use of ACPI with the board requires an operating system that provides full ACPI support. ACPI features include: • Plug and Play (including bus and device enumeration) • Power management control of individual devices, add-in boards (some add-in boards may require an ACPI-aware driver), video displays, and hard disk drives • Methods for achieving less than 15-watt system operation in the power-on/standby sleeping state • A Soft-off feature that enables the operating system to power-off the computer • Support for multiple wake-up events (see Table 9 on page 31) • Support for a front panel power and sleep mode switch Table 7 lists the system states based on how long the power switch is pressed, depending on how ACPI is configured with an ACPI-aware operating system. Table 7. Effects of Pressing the Power Switch If the system is in this …and the power switch state… is pressed for …the system enters this state Off Less than four seconds Power-on (ACPI G2/G5 – Soft off) (ACPI G0 – working state) On Less than four seconds Power-off (ACPI G0 – working state) (ACPI G2/G5 – Soft off) On More than four seconds Fail safe power-off (ACPI G0 – working state) (ACPI G2/G5 – Soft off) Sleep Less than four seconds Wake-up (ACPI G1 – sleeping state) (ACPI G0 – working state) Sleep More than four seconds Power-off (ACPI G1 – sleeping state) (ACPI G2/G5 – Soft off) 29 Intel Desktop Board D510MO Technical Product Specification 1.11.1.1 System States and Power States Under ACPI, the operating system directs all system and device power state transitions. The operating system puts devices in and out of low-power states based on user preferences and knowledge of how devices are being used by applications. Devices that are not being used can be turned off. The operating system uses information from applications and user settings to put the system as a whole into a low-power state. Table 8 lists the power states supported by the board along with the associated system power targets. See the ACPI specification for a complete description of the various system and power states. Table 8. Power States and Targeted System Power Global Processor Targeted System (Note 1) States Sleeping States States Device States Power G0 – working S0 – working C0 – working D0 – working Full power > 30 W state state. G1 – sleeping S1 – Processor C1 – stop D1, D2, D3 – 5 W < power < 52.5 W state stopped grant device specification specific. (Note 2) G1 – sleeping S3 – Suspend to No power D3 – no power Power < 5 W state RAM. Context except for saved to RAM. wake-up logic. (Note 2) G1 – sleeping S4 – Suspend to No power D3 – no power Power < 5 W state disk. Context except for saved to disk. wake-up logic. (Note 2) G2/S5 S5 – Soft off. No power D3 – no power Power < 5 W Context not saved. except for Cold boot is wake-up logic. required. G3 – No power to the No power D3 – no power for No power to the system. mechanical off. system. wake-up logic, Service can be performed AC power is except when safely. disconnected provided by from the battery or computer. external source. Notes: 1. Total system power is dependent on the system configuration, including add-in boards and peripherals powered by the system’s power supply. 2. Dependent on the standby power consumption of wake-up devices used in the system. 30 Product Description 1.11.1.2 Wake-up Devices and Events Table 9 lists the devices or specific events that can wake the computer from specific states. Table 9. Wake-up Devices and Events These devices/events can wake up the computer… …from this state (Note 1) LAN S1, S3, S4, S5 (Note 1) PME# signal S1, S3, S4, S5 (Notes 1 and 3) Wake# signal S1, S3, S4, S5 (Note 1) Power switch S1, S3, S4, S5 (Note 1) RTC alarm S4, S5 Serial port S1, S3 (Note 2) USB S1, S3 (Notes 1 and 4) PS/2 devices S1, S3, S4, S5 Notes: 1. S4 implies operating system support only. Wake from S5 must include wake after loss of power. 2. USB ports are turned off during S4/S5 states. 3. Wake# signal must be controllable by the BIOS (enable/disable option). 4. PS/2 wake from S5 should have a selection in the BIOS to enable wake from a combination key (Alt + Print Screen) or the keyboard power button. NOTE The use of these wake-up events from an ACPI state requires an operating system that provides full ACPI support. In addition, software, drivers, and peripherals must fully support ACPI wake events. 31 Intel Desktop Board D510MO Technical Product Specification 1.11.2 Hardware Support The board provides several power management hardware features, including: • Power connector • Fan header • LAN wake capabilities • Instantly Available PC technology • Wake from USB • Wake from PS/2 devices • Power Management Event signal (PME#) wake-up support • WAKE# signal wake-up support • +5V Standby Power Indicator LED LAN wake capabilities and Instantly Available PC technology require power from the +5 V standby line. NOTE The use of Wake from USB technologies from an ACPI state requires an operating system that provides full ACPI support. 1.11.2.1 Fan Header The function/operation of the fan header is as follows: • The fan is on when the board is in the S0 state. • The fan is off when the board is off or in the S3, S4, or S5 state. • The chassis fan header supports closed-loop fan control that can adjust the fan speed and is wired to a fan tachometer input. • The fan header supports +12 V, 3-wire fans at 1 A maximum. For information about Refer to The locations of the fan header and thermal sensors Figure 5, page 28 The signal names of the chassis fan header Table 16, page 45 1.11.2.2 LAN Wake Capabilities LAN wake capabilities enable remote wake-up of the computer through a network. The LAN subsystem network adapter monitors network traffic at the Media Independent Interface. The board supports LAN wake capabilities with ACPI in the following ways: • By Ping • By Magic Packet Upon detecting the configured wake packet type, the LAN subsystem asserts a wake- up signal that powers up the computer. 32 Product Description 1.11.2.3 Instantly Available PC Technology Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to- RAM) sleep-state. While in the S3 sleep-state, the computer will appear to be off (the hard drive(s) and fan will power off, the front panel LED will blink). When signaled by a wake-up device or event, the system quickly returns to its last known state. Table 9 on page 31 lists the devices and events that can wake the computer from the S3 state. The board supports the PCI Bus Power Management Interface Specification. Add-in boards that also support this specification can participate in power management and can be used to wake the computer. The use of Instantly Available PC technology requires operating system support and PCI 2.3 compliant add-in cards and drivers. 1.11.2.4 Wake from USB USB bus activity wakes the computer from an ACPI S1 or S3 state. NOTE Wake from USB requires the use of a USB peripheral that supports Wake from USB and support in the operating system. 1.11.2.5 PME# Signal Wake-up Support When the PME# signal on the PCI bus is asserted, the computer wakes from an ACPI S1, S3, S4, or S5 state (with Wake on PME enabled in the BIOS). 1.11.2.6 Wake from PS/2 Devices PS/2 keyboard activity wakes the computer from an ACPI S1, S3, S4, or S5 state. However, when the computer is in an ACPI S4 or S5 state, the only PS/2 activity that will wake the computer is the Alt + Print Screen or the Power Key available only on some keyboards. 1.11.2.7 WAKE# Signal Wake-up Support When the WAKE# signal on the PCI Express bus is asserted, the computer wakes from an ACPI S1, S3, S4, or S5 state. 1.11.2.8 Wake from Serial Port Serial Port activity wakes the computer from an ACPI S1 or S3 state. 33 Intel Desktop Board D510MO Technical Product Specification 1.11.2.9 +5 V Standby Power Indicator LED The +5 V standby power indicator LED shows that power is still present even when the computer appears to be off. Figure 6 shows the location of the standby power indicator LED. CAUTION If AC power has been switched off and the standby power indicator is still lit, disconnect the power cord before installing or removing any devices connected to the board. Failure to do so could damage the board and any attached devices. Figure 6. Location of the Standby Power Indicator LED 34 Product Description 1.11.3 ENERGY STAR*, E-Standby, and EuP Compliance The US Department of Energy and the US Environmental Protection Agency have continually revised the ENERGY STAR requirements. Intel has worked directly with these two governmental agencies in the definition of new requirements. This Intel Desktop Board meets the ENERGY STAR requirements listed in Table 10 when used in corresponding system configurations. NOTE Energy Star compliance is based at the system level not the board level. Use of an Intel Desktop Board alone does not guarantee Energy Star compliance. Table 10. ENERGY STAR Requirements ENERGY STAR Capability Specification Computer Type Req States Adjustments TEC Criteria v4.0 Desktop Computer Idle State (Cat A) With and without N/A WOL (Sleep, Sleep Mode Standby) v4.0 Integrated Computer Standby Level v5.0 Desktop Computer Off Mode With and without Cat A under additional internal “desktop Sleep Mode storage conventional” and “desktop Idle State proxying” Active State operational mode v5.0 Integrated Desktop weightings Computer v5.0 Thin Client Off Mode With and without N/A WOL (Sleep, Sleep Mode Standby) Idle State (Cat B) For information about Refer to ENERGY STAR requirements and recommended configurations http://www.intel.com/go/energystar Intel Desktop Board D510MO also meets the following international program requirements: • Korea E-Standby • European Union EuP 35 Intel Desktop Board D510MO Technical Product Specification 36 2 Technical Reference 2.1 Memory Map 2.1.1 Addressable Memory The board utilizes 4 GB of addressable system memory. Typically the address space that is allocated for PCI Conventional bus add-in cards, PCI Express configuration space, BIOS (SPI Flash), and chipset overhead resides above the top of DRAM (total system memory). On a system that has 4 GB of system memory installed, it is not possible to use all of the installed memory due to system address space being allocated for other system critical functions. These functions include the following: • BIOS/ SPI Flash (4 MB) • Local APIC (19 MB) • Direct Media Interface (40 MB) • Front side bus interrupts (17 MB) • GMCH base address registers, internal graphics ranges • Memory-mapped I/O that is dynamically allocated for PCI Conventional add-in cards 37 Intel Desktop Board D510MO Technical Product Specification The amount of installed memory that can be used will vary based on add-in cards and BIOS settings. Figure 7 shows a schematic of the system memory map. All installed system memory can be used when there is no overlap of system addresses. Figure 7. Detailed System Memory Address Map 38 Technical Reference Table 11 lists the system memory map. Table 11. System Memory Map Address Range Address Range (decimal) (hex) Size Description 1024 K - 4096 K 100000 - 400000 4096 MB Extended memory 960 K - 1024 K F0000 - FFFFF 64 KB Runtime BIOS 896 K - 960 K E0000 - EFFFF 64 KB Reserved 800 K - 896 K C8000 - DFFFF 96 KB Potential available high DOS memory (open to the PCI bus). Dependent on video adapter used. 640 K - 800 K A0000 - C7FFF 160 KB Video memory and BIOS 639 K - 640 K 9FC00 - 9FFFF 1 KB Extended BIOS data (movable by memory manager software) 512 K - 639 K 80000 - 9FBFF 127 KB Extended conventional memory 0 K - 512 K 00000 - 7FFFF 512 KB Conventional memory 39 Intel Desktop Board D510MO Technical Product Specification 2.2 Connectors and Headers CAUTION Only the following connectors/headers have overcurrent protection: Back panel and front panel USB and PS/2. The other internal connectors/headers are not overcurrent protected and should connect only to devices inside the computer’s chassis, such as fans and internal peripherals. Do not use these connectors/headers to power devices external to the computer’s chassis. A fault in the load presented by the external devices could cause damage to the computer, the power cable, and the external devices themselves. NOTE Computer systems that have an unshielded cable attached to a USB port may not meet FCC Class B requirements, even if no device is attached to the cable. Use shielded cable that meets the requirements for full-speed devices. This section describes the board’s connectors and headers. The connectors and headers can be divided into these groups: • Back panel I/O connectors (see page 41) • Component-side connectors and headers (see page 43) 40 Technical Reference 2.2.1 Back Panel 2.2.1.1 Back Panel Connectors Figure 8 shows the location of the back panel connectors. Item Description A PS/2 keyboard/mouse connector B PS/2 keyboard/mouse connector C VGA port D USB ports E LAN connector (RJ-45) F USB ports G Line in H Line out I Mic in Figure 8. Back Panel Connectors NOTE The back panel audio line out connector is designed to power headphones or amplified speakers only. Poor audio quality occurs if passive (non-amplified) speakers are connected to this output. 41 Intel Desktop Board D510MO Technical Product Specification 2.2.1.2 I/O Shield The I/O shield provided with the board allows access to all back panel connectors and is compatible with standard mini-ITX and microATX chassis. As an added benefit for system configurations with wireless PCI Express Mini Card solutions, the I/O shield also provides pre-cut holes for user installation of up to three external wireless antennas. Figure 9 shows an I/O shield reference diagram. Figure 9. I/O Shield Reference Diagram 42 Technical Reference 2.2.2 Component-side Connectors and Headers Figure 10 shows the locations of the component-side connectors and headers. Figure 10. Component-side Connectors and Headers 43 Intel Desktop Board D510MO Technical Product Specification Table 12 lists the component-side connectors and headers identified in Figure 10. Table 12. Component-side Connectors and Headers Shown in Figure 10 Item/callout from Figure 10 Description S/PDIF header A B Serial port header (COM 1) C Parallel port header D Serial port header (COM 2) E LVDS inverter power voltage selection jumper (optional) Chassis fan header F G Main power connector (2 x 12) H LVDS inverter power connector (optional) I LVDS inverter panel voltage selection header (optional) J LVDS panel connector (optional) SATA connector 1 K SATA connector 0 L M Front panel header N Front panel wireless activity LED header O Front panel USB header (with Intel Z-U130 USB Solid-State Drive, or compatible device, support) P PCI conventional bus connector Q USB front panel header R Front panel audio header 44 Technical Reference 2.2.2.1 Signal Tables for the Connectors and Headers Table 13. Serial Port Header (COM 1 and COM 2) Pin Signal Name Pin Signal Name 1 DCD (Data Carrier Detect) 2 RXD# (Receive Data) 3 TXD# (Transmit Data) 4 DTR (Data Terminal Ready) 5 Ground 6 DSR (Data Set Ready) 7 RTS (Request To Send) 8 CTS (Clear To Send) 9 RI (Ring Indicator) 10 Key (no pin) Table 14. LVDS Data Connector - 30-Pin (Optional) Signal Signal Pin Name Description Pin Name Description 1 LA_CLKN LVDS Channel A diff 2 NC clock output - negative 3 LA_CLKP LVDS Channel A diff 4 NC clock output - positive 5 EDID_3.3V Power for EDID ROM 6 EDID_GND Ground for EDID signaling 7 LA_DATAN0 LVDS Channel A diff 8 NC data output – negative 9 LA_DATAP0 LVDS Channel A diff 10 NC data output – positive 11 LA_DATAN1 LVDS Channel A diff 12 NC data output – negative 13 LA_DATAP1 LVDS Channel A diff 14 NC data output – positive 15 GND Ground 16 GND Ground 17 LA_DATAN2 LVDS Channel A diff 18 NC data output – negative 19 LA_DATAP2 LVDS Channel A diff 20 NC data output – positive 21 GND Ground 22 GND Ground 23 GND Ground 24 GND Ground 25 3.3 V/5 V/12 V Selectable LCD 26 3.3 V/5 V/12 V Selectable LCD power power output output 27 3.3 V/5 V/12 V Selectable LCD 28 3.3 V/5 V/12 V Selectable LCD power power output output 29 EDID_CLK EDID/DDC clock 30 EDID_DATA EDID/DDC data signal signal 45 Intel Desktop Board D510MO Technical Product Specification Table 15. LVDS Panel Voltage Selection Jumper (Optional) Voltage Jumper Setting Configuration 3.3 V 2 and 4 Jumper position for 3.3 V (default) 5 V 6 and 4 Jumper position for 5 V 12 V 3 and 4 Jumper position for 12 V Table 16. Chassis Fan Header Pin Signal Name 1 Ground 2 +12 V (PWM controlled pulses) 3 Tach Table 17. SATA Connectors Pin Signal Name 1 Ground 2 TXP 3 TXN 4 Ground 5 RXN 6 RXP 7 Ground 46 Technical Reference Table 18. LVDS Inverter Power Connector (Optional) Pin Signal Name Description 1 GND Ground 2 GND Ground 3 5 V/12 V Inverter power 4 5 V/12 V Inverter power 5 INV_RATING Inverter rating 6 BKLT_PWM Backlight PWM 7 BKLT_EN Backlight enable Table 19. LVDS Inverter Power Voltage Selection Jumper (Optional) Voltage Jumper Setting Configuration 5 V 1 and 2 Jumper position for 5 V (default) 12 V 3 and 2 Jumper position for 12 V 47 Intel Desktop Board D510MO Technical Product Specification Table 20. Parallel Port Header Pin Standard Signal Name ECP Signal Name EPP Signal Name 1 STROBE# STROBE# WRITE# 2 AUTOFD# AUTOFD#, HOSACK DATASTB# 3 PD0 PD0 PD0 4 FAULT# FAULT#, PERIPHREQST# FAULT# 5 PD1 PD1 PD1 6 INT# INT#, REVERSERQST# RESET# 7 PD2 PD2 PD2 8 SLCTIN# SLCTIN# ADDRSTB# 9 PD3 PD3 PD3 10 GROUND GROUND GROUND 11 PD4 PD4 PD4 12 GROUND GROUND GROUND 13 PD5 PD5 PD5 14 GROUND GROUND GROUND 15 PD6 PD6 PD6 16 GROUND GROUND GROUND 17 PD7 PD7 PD7 18 GROUND GROUND GROUND 19 ACK# ACK# INTR 20 GROUND GROUND GROUND 21 BUSY BUSY#, PERIPHACK WAIT# 22 GROUND GROUND GROUND 23 PERROR PE, ACKREVERSE# PE 24 GROUND GROUND GROUND 25 SELECT SELECT SELECT 26 KEY (no pin) KEY (no pin) KEY (no pin) Table 21. Front Panel Wireless Activity LED Header Pin Signal Name 1 LED (+) 2 Ground Table 22. S/PDIF Header Pin Signal Name 1 VCC (5 V) 2 S/PDIF out 3 Ground 48 Technical Reference Table 23. Front Panel Audio Header for Intel HD Audio Pin Signal Name Pin Signal Name 1 [Port 1] Left channel 2 Ground 3 [Port 1] Right channel 4 PRESENCE# (Dongle present) 5 [Port 2] Right channel 6 [Port 1] SENSE_RETURN 7 SENSE_SEND (Jack detection) 8 Key (no pin) 9 [Port 2] Left channel 10 [Port 2] SENSE_RETURN Table 24. Front Panel Audio Header for AC ’97 Audio Pin Signal Name Pin Signal Name 1 MIC 2 AUD_GND 3 MIC_BIAS 4 AUD_GND 5 FP_OUT_R 6 FP_RETURN_R 7 AUD_5V 8 KEY (no pin) 9 FP_OUT_L 10 FP_RETURN_L Table 25. Front Panel USB Header Pin Signal Name Pin Signal Name 1 +5 VDC 2 +5 VDC 3 D- 4 D- 5 D+ 6 D+ 7 Ground 8 Ground 9 KEY (no pin) 10 No Connect Table 26. Front Panel USB Header (with Intel Z-U130 USB Solid-State Drive, or Compatible Device, Support) Pin Signal Name Pin Signal Name 1 +5 VDC 2 NC 3 D- 4 NC 5 D+ 6 NC 7 Ground 8 NC 9 KEY (no pin) 10 LED# 49 Intel Desktop Board D510MO Technical Product Specification 2.2.2.2 Add-in Card Connectors The board has the following add-in card connectors: • PCI Express x1 Mini Card (rev 1.2 compliant) connector • PCI Conventional (rev 2.3 compliant) bus connector Note the following considerations for the PCI Conventional bus connector: • The PCI Conventional bus connector is bus master capable. • SMBus signals are routed to the PCI Conventional bus connector. This enables PCI Conventional bus add-in boards with SMBus support to access sensor data on the board. The specific SMBus signals are as follows: ⎯ The SMBus clock line is connected to pin A40. ⎯ The SMBus data line is connected to pin A41. The PCI Conventional bus connector also supports single-slot and dual-slot riser cards for use of up to two bus master PCI expansion cards. In order to support two PCI bus master expansion cards, the riser card must support the following PCI signal routing: • Pin A11: additional 33 MHz PCI clock • Pin B10: additional PCI Request signal (i.e., PREQ#2) • Pin B14: additional PCI Grant signal (i.e., GNT#2) 2.2.2.3 Power Supply Connector The board has a 2 x 12 power connector (see Table 27). This board requires a TFX12V or SFX12V power supply. Table 27. Power Connector Pin Signal Name Pin Signal Name 1 +3.3 V 13 +3.3 V 2 +3.3 V 14 -12 V 3 Ground 15 Ground 4 +5 V 16 PS-ON# (power supply remote on/off) 5 Ground 17 Ground 6 +5 V 18 Ground 7 Ground 19 Ground 8 PWRGD (Power Good) 20 No connect 9 +5 V (Standby) 21 +5 V 10 +12 V 22 +5 V 11 +12 V 23 +5 V 12 No connect 24 Ground 50 Technical Reference 2.2.2.4 Front Panel Header This section describes the functions of the front panel header. Table 28 lists the signal names of the front panel header. Figure 11 is a connection diagram for the front panel header. Table 28. Front Panel Header In/ In/ Pin Signal Out Description Pin Signal Out Description Hard Drive Activity LED Power LED 1 HD_PWR Out Hard disk LED 2 HDR_BLNK_GRN Out Front panel green pull-up to +5 V LED 3 HDA# Out Hard disk active 4 HDR_BLNK_YEL Out Front panel yellow LED LED Reset Switch On/Off Switch 5 Ground Ground 6 FPBUT_IN In Power switch 7 FP_RESET# In Reset switch 8 Ground Ground Power Not Connected 9 +5 V Power 10 N/C Not connected Figure 11. Connection Diagram for Front Panel Header 51 Intel Desktop Board D510MO Technical Product Specification 2.2.2.4.1 Hard Drive Activity LED Header Pins 1 and 3 can be connected to an LED to provide a visual indicator that data is being read from or written to a hard drive. Proper LED function requires one of the following: • SATA storage device connected to an onboard SATA connector • Intel Z-U130 USB Solid State Drive (or compatible device) connected to the designated Z-U130 front panel USB header 2.2.2.4.2 Reset Switch Header Pins 5 and 7 can be connected to a momentary single pole, single throw (SPST) type switch that is normally open. When the switch is closed, the board resets and runs the POST. 2.2.2.4.3 Power/Sleep LED Header Pins 2 and 4 can be connected to a single- or dual-color LED. Table 29 shows the default states for a single-color LED. Table 29. States for a One-Color Power LED LED State Description Off Power off/hibernate (S5/S4) Blinking Sleeping (S3) Steady Green Running/Away (S0/S1) NOTE The LED states listed in Table 29 are default settings that can be modified through BIOS setup. Systems built with a dual-color front panel power LED can also use alternate color state options. 2.2.2.4.4 Power Switch Header Pins 6 and 8 can be connected to a front panel momentary-contact power switch. The switch must pull the SW_ON# pin to ground for at least 50 ms to signal the power supply circuitry to switch on or off. (The time requirement is due to internal debounce circuitry on the board.) At least two seconds must pass before the power supply circuitry will recognize another on/off signal. 52 Technical Reference 2.2.2.5 Front Panel USB Headers Figure 12 and Figure 13 are connection diagrams for the front panel USB headers. NOTE • The +5 VDC power on the USB headers is fused. • Use only a front panel USB connector that conforms to the USB 2.0 specification for high-speed USB devices. Figure 12. Connection Diagram for Front Panel USB Header Figure 13. Connection Diagram for Front Panel USB Header (with Intel Z-U130 USB Solid-State Drive, or Compatible Device, Support) 53 Intel Desktop Board D510MO Technical Product Specification 2.3 BIOS Configuration Jumper Block CAUTION Do not move the jumper with the power on. Always turn off the power and unplug the power cord from the computer before changing a jumper setting. Otherwise, the board could be damaged. Figure 14 shows the location of the jumper block. The jumper determines the BIOS Setup program’s mode. Table 30 lists the jumper settings for the three modes: normal, configure, and recovery. Figure 14. Location of the BIOS Configuration Jumper Block 54 Technical Reference Table 30. BIOS Configuration Jumper Settings Function/Mode Jumper Setting Configuration Normal 1-2 The BIOS uses current configuration information and passwords for booting. 32 1 Configure 2-3 After the POST runs, Setup runs automatically. The maintenance menu is displayed. 32 1 Recovery None The BIOS attempts to recover the BIOS configuration. See Section 3.7 for more information on BIOS recovery. 32 1 55 Intel Desktop Board D510MO Technical Product Specification 2.4 Mechanical Considerations 2.4.1 Form Factor The board is designed to fit into a mini-ITX or microATX form-factor chassis. Figure 15 illustrates the mechanical form factor for the board. Dimensions are given in inches [millimeters]. The outer dimensions are 6.7 inches by 6.7 inches [170 millimeters by 170 millimeters]. Location of the I/O connectors and mounting holes are in compliance with the microATX specification. Figure 15. Board Dimensions 56 Technical Reference 2.5 Electrical Considerations 2.5.1 Fan Header Current Capability Table 31 lists the current capability of the fan header. Table 31. Fan Header Current Capability Fan Header Maximum Available Current Chassis fan 1.0 A 2.5.2 Add-in Board Considerations The board is designed to provide 2 A (average) of +5 V current for the PCI Conventional slot. The total +5 V current draw for the PCI Conventional expansion slot (total load) must not exceed 2 A. 2.6 Thermal Considerations CAUTION o A chassis with a maximum internal ambient temperature of 38 C at the processor fan inlet is a requirement. CAUTION Failure to ensure appropriate airflow may result in reduced performance of both the processor and/or voltage regulator or, in some instances, damage to the board. For a list of chassis that have been tested with Intel Desktop Boards please refer to the following website: http://developer.intel.com/design/motherbd/cooling.htm All responsibility for determining the adequacy of any thermal or system design remains solely with the reader. Intel makes no warranties or representations that merely following the instructions presented in this document will result in a system with adequate thermal performance. CAUTION Ensure that the ambient temperature does not exceed the board’s maximum operating temperature. Failure to do so could cause components to exceed their maximum case temperature and malfunction. For information about the maximum operating temperature, see the environmental specifications in Section 2.9. 57 Intel Desktop Board D510MO Technical Product Specification CAUTION Ensure that proper airflow is maintained in the processor voltage regulator circuit. Failure to do so may result in damage to the voltage regulator circuit. The processor o voltage regulator area (shown in Figure 16) can reach a temperature of up to 85 C in an open chassis. Figure 16 shows the locations of the localized high temperature zones. Item Description A Processor voltage regulator area B Intel Atom processor Intel NM10 Express Chipset C Figure 16. Localized High Temperature Zones Table 32 provides maximum case temperatures for the board components that are sensitive to thermal changes. The operating temperature, current load, or operating frequency could affect case temperatures. Maximum case temperatures are important when considering proper airflow to cool the board. 58 Technical Reference Table 32. Thermal Considerations for Components Component Maximum Case Temperature o Intel Atom processor 99 C o Processor voltage regulator area 85 C o Intel NM10 Express Chipset 113 C o Memory DIMM 85 C For information about Refer to Processor datasheets and specification updates Section 1.2, page 16 2.6.1 Passive Heatsink Design in a Passive System Environment This section highlights important guidelines and related thermal boundary conditions for passive heatsink design in a passive system environment. Passive heatsink describes a thermal solution without a fan attached. Passive system environment describes a chassis with either a power supply fan or a built-in chassis fan. This information should be used in conjunction with the Thermal/Mechanical ® Specifications and Design Guidelines (TMSDG) published for Intel Atom™ D400 and D500 Series processors. The TMSDG contains detailed package information and thermal mechanical specifications for the processors. The TMSDG also contains information on how to enable a completely fanless design provided the right usage scenario and boundary conditions are observed for optimal thermal design. While the TMSDG has a section on thermal design for passive system environments (pages 29-30), the information in this section can also be used to complement the TMSDG. 2.6.1.1 Definition of Terms Term Description T The measured ambient temperature locally surrounding the processor. The ambient A temperature should be measured just upstream of a passive heatsink. T Processor junction temperature. J Ψ Junction-to-ambient thermal characterization parameter (psi). A measure of thermal solution JA performance using total package power. Defined as (T - T )/TDP. J A Note: Heat source must be specified for Ψ measurements. TIM Thermal Interface Material: the thermally conductive compound between the heatsink and the processor die surface. This material fills the air gaps and voids, and enhances the transfer of the heat from the processor die surface to the heatsink. TDP Thermal Design Power: a power dissipation target based on worst-case applications. Thermal solutions should be designed to dissipate the thermal design power. T external The measured external ambient temperature surrounding the chassis. The external ambient A temperature should be measured just upstream of the chassis inlet vent. 59 Intel Desktop Board D510MO Technical Product Specification 2.6.1.2 Thermal Specifications Guideline Terms Requirements T ≤ 50 °C A T ≤ 100 °C J Ψ ≤ 3.85 °C/W JA TIM Honeywell PCM45F TDP 13 W T external ≤ 35 °C A 2.6.1.3 Heatsink Design Guideline Maximum heatsink size* 87 x 62 x 35.54 mm Heatsink mass ≤ 80 grams Retention type Spring loaded fasteners Heatsink preload 11.3 +/- 3.6 lb Note: Refers to the heatsink installed on the board. 2.6.1.4 Chassis Design Guideline The pin fin heatsink design used on this board will be able to dissipate up to 13 W of processor power in most of the passively enabled system chassis. This board is targeted for 3-7 liters volumetric or larger, desktop/tower orientation, mini-ITX and micro-ATX chassis with a chassis fan. The recommended fan type is an exhaust fan. For best thermal performance, it is recommended that the chassis fan provide reasonable airflow directly over the all the major components on the board. The pin fin heatsink is designed to have the best thermal performance when airflow direction is parallel to the heatsink fins. The processor on the board will generate the highest amount of heat, leading to high ambient temperature within the chassis. The chassis fan should be located near the board region in order to effectively regulate airflow (see Figure 17). A chassis fan located further away from the board region, i.e., at the optical disk drive or hard disk drive region, will be less effective in controlling the local ambient temperature. Regardless of where the chassis fan is located, the maximum local ambient temperature as defined by TA should be capped at 50 °C. Chassis inlet vents should also provide adequate openings for airflow to pass through. The recommended free- area-ratio of chassis vents should be equal to or greater than 0.53. By using the reference pin fin heatsink, most chassis with a chassis fan enabled should have local ambient temperature safely below the 50 °C limit. 60 Technical Reference Figure 17. Fan Location Guide for Cassis Selection (Chassis Orientation is Not Restricted) For all chassis configurations, the heatsink performance parameter, Ψ should be less JA than 3.85 °C/W. The detail thermal measurement metrology is described in the TMSDG. For chassis that fail to meet the thermal specifications guideline highlighted above, an actively cooled heatsink solution should be used. 61 Intel Desktop Board D510MO Technical Product Specification 2.7 Power Consumption Power measurements were performed to determine bare minimum and likely maximum power requirements from the board, as well as attached devices, in order to facilitate power supply rating estimates for specific system configurations. 2.7.1 Minimum Load Configuration Minimum load refers to the power demand placed on the power supply when using a bare system configuration with minimal power requirement conditions. Minimum load configuration test results are shown in Table 33. The test configuration was defined as follows: • 4 GB DDR2/667 MHz DIMM • USB keyboard and mouse • LAN linked at 1 Gb/s • DOS booted via network (PXE); system at idle • All on board peripherals enabled (serial, parallel, audio, …) Table 33. Minimum Load Configuration Current and Power Results Current Draw at 12 V Power Consumption 1.737 A 20.844 W 2.7.2 Maximum Load Configuration Maximum load refers to the incremental power demands placed on the power supply, augmenting the minimum load configuration into a fully-featured system that stresses power consumption from all subsystems. Maximum load configuration test results are shown in Table 34. The test configuration was defined as follows: • 4 GB DDR2/667 MHz DIMM • 14.1-inch LCD via LVDS • SATA DVD-R/W ⎯ Load: DVD playback • 3.5-inch SATA hard disk drive, running Microsoft Windows Vista Home Basic ⎯ Load: continuous read/write benchmark • Intel Z-U130 USB Solid-State Drive (or compatible device) on the USB flash drive header ⎯ Load: continuous read/write benchmark • Wireless card on PCI Express Mini Card slot, connected via 802.11n protocol ⎯ Load: continuous read/write benchmark on remote share • Riser card on conventional PCI slot, populated with PCI LAN card, running file transfer through local network to SATA hard drive • USB keyboard and mouse 62 Technical Reference • Back and front panel host-powered USB devices (other than keyboard and mouse) ⎯ Load: continuous read/write activity on external drive/peripheral • LAN linked at 1 Gbps ⎯ Load: continuous read/write benchmark on remote share • All on board peripherals enabled (serial, parallel, audio, …) Table 34. Maximum Load Configuration Current and Power Results Subsystem Current Draw at 12 V Power Consumption Minimum Load Configuration 1.737 A 20.844 W 14.1-inch LCD via LVDS 0.532 6.384 W SATA DVD-R/W 0.332 A 3.984 W 3.5-inch SATA hard disk drive 0.724 A 8.688 W Intel Z-U130 USB Solid State Drive 0.062 A 0.744 W (or compatible device) Wireless PCI Express Mini Card 0.2 A 2.4 W PCI cards on riser 0.131 A 1.572 W Host-powered USB devices (other 0.107 A 1.284 W than keyboard and mouse) Maximum Load Configuration 3.825 A 45.9 W 2.8 Reliability The Mean Time Between Failures (MTBF) prediction is calculated using component and subassembly random failure rates. The calculation is based on the Bellcore Reliability Prediction Procedure, TR-NWT-000332, Issue 4, September 1991. The MTBF prediction is used to estimate repair rates and spare parts requirements. The MTBF data was calculated from predicted data at 55 ºC. The Intel Desktop Board D510MO MTBF is 248,232.584 hours. 63 Intel Desktop Board D510MO Technical Product Specification 2.9 Environmental Table 35 lists the environmental specifications for the board. Table 35. Intel Desktop Board D510MO Environmental Specifications Parameter Specification Temperature Non-Operating -20 °C to +70 °C Operating 0 °C to +50 °C Shock Unpackaged 50 g trapezoidal waveform Velocity change of 170 inches/second² Packaged Half sine 2 millisecond Product weight (pounds) Free fall (inches) Velocity change (inches/sec²) <20 36 167 21-40 30 152 41-80 24 136 81-100 18 118 Vibration Unpackaged 5 Hz to 20 Hz: 0.01 g² Hz sloping up to 0.02 g² Hz 20 Hz to 500 Hz: 0.02 g² Hz (flat) Packaged 10 Hz to 40 Hz: 0.015 g² Hz (flat) 40 Hz to 500 Hz: 0.015 g² Hz sloping down to 0.00015 g² Hz 64 3 Overview of BIOS Features 3.1 Introduction The board uses an Intel BIOS that is stored in the Serial Peripheral Interface Flash Memory (SPI Flash) and can be updated using a disk-based program. The SPI Flash contains the BIOS Setup program, POST, the PCI auto-configuration utility, LAN EEPROM information, and Plug and Play support. The BIOS displays a message during POST identifying the type of BIOS and a revision code. The initial production BIOSs are identified as MOPNV10J.86A. The BIOS Setup program can be used to view and change the BIOS settings for the computer. The BIOS Setup program is accessed by pressing the key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins. The menu bar is shown below. Maintenance Main Advanced Security Power Boot Exit NOTE The maintenance menu is displayed only when the board is in configure mode. Section 2.3 on page 54 shows how to put the board in configure mode. 65 Intel Desktop Board D510MO Technical Product Specification Table 36 lists the BIOS Setup program menu features. Table 36. BIOS Setup Program Menu Bar Maintenance Main Advanced Security Power Boot Exit Clears Displays Configures Sets Configures Selects boot Saves or passwords and processor advanced passwords power options discards displays and memory features and security management changes to processor configuration available features features and Setup information through the power states program chipset options options Table 37 lists the function keys available for menu screens. Table 37. BIOS Setup Program Function Keys BIOS Setup Program Function Key Description <←> or <→> Selects a different menu screen (Moves the cursor left or right) <↑> or <↓> Selects an item (Moves the cursor up or down) Executes command or selects the submenu Load the default configuration values for the current menu Save the current values and exits the BIOS Setup program Exits the menu 3.2 BIOS Flash Memory Organization The Serial Peripheral Interface Flash Memory (SPI Flash) includes an 8 Mbit (1024 KB) flash memory device. 3.3 Resource Configuration 3.3.1 PCI* Autoconfiguration The BIOS can automatically configure PCI devices. PCI devices may be onboard or add-in cards. Autoconfiguration lets a user insert or remove PCI cards without having to configure the system. When a user turns on the system after adding a PCI card, the BIOS automatically configures interrupts, the I/O space, and other system resources. Any interrupts set to Available in Setup are considered to be available for use by the add-in card. 66 Overview of BIOS Features 3.4 System Management BIOS (SMBIOS) SMBIOS is a Desktop Management Interface (DMI) compliant method for managing computers in a managed network. The main component of SMBIOS is the Management Information Format (MIF) database, which contains information about the computing system and its components. Using SMBIOS, a system administrator can obtain the system types, capabilities, operational status, and installation dates for system components. The MIF database defines the data and provides the method for accessing this information. The BIOS enables applications such as third-party management software to use SMBIOS. The BIOS stores and reports the following SMBIOS information: • BIOS data, such as the BIOS revision level • Fixed-system data, such as peripherals, serial numbers, and asset tags • Resource data, such as memory size, cache size, and processor speed • Dynamic data, such as event detection and error logging Non-Plug and Play operating systems require an additional interface for obtaining the SMBIOS information. The BIOS supports an SMBIOS table interface for such operating systems. Using this support, an SMBIOS service-level application running on a non-Plug and Play operating system can obtain the SMBIOS information. Additional board information can be found in the BIOS under the Additional Information header under the Main BIOS page. 67 Intel Desktop Board D510MO Technical Product Specification 3.5 Legacy USB Support Legacy USB support enables USB devices to be used even when the operating system’s USB drivers are not yet available. Legacy USB support is used to access the BIOS Setup program, and to install an operating system that supports USB. By default, Legacy USB support is set to Enabled. Legacy USB support operates as follows: 1. When you apply power to the computer, legacy support is disabled. 2. POST begins. 3. Legacy USB support is enabled by the BIOS allowing you to use a USB keyboard to enter and configure the BIOS Setup program and the maintenance menu. 4. POST completes. 5. The operating system loads. While the operating system is loading, USB keyboards and mice are recognized and may be used to configure the operating system. (Keyboards and mice are not recognized during this period if Legacy USB support was set to Disabled in the BIOS Setup program.) 6. After the operating system loads the USB drivers, all legacy and non-legacy USB devices are recognized by the operating system, and Legacy USB support from the BIOS is no longer used. 7. Additional USB legacy feature options can be accessed by using Intel Integrator Toolkit. To install an operating system that supports USB, verify that Legacy USB support in the BIOS Setup program is set to Enabled and follow the operating system’s installation instructions. 68 Overview of BIOS Features 3.6 BIOS Updates The BIOS can be updated using either of the following utilities, which are available on the Intel World Wide Web site: ® • Intel Express BIOS Update utility, which enables automated updating while in the Windows environment. Using this utility, the BIOS can be updated from a file on a hard disk, a USB drive (a flash drive or a USB hard drive), or a CD-ROM, or from the file location on the Web. ® • Intel Flash Memory Update Utility, which requires booting from DOS. Using this utility, the BIOS can be updated from a file on a hard disk, a USB drive (a flash drive or a USB hard drive), or a CD-ROM. Both utilities verify that the updated BIOS matches the target system to prevent accidentally installing an incompatible BIOS. NOTE Review the instructions distributed with the upgrade utility before attempting a BIOS update. For information about Refer to BIOS update utilities http://downloadcenter.intel.com 3.6.1 BIOS Recovery It is unlikely that anything will interrupt a BIOS update; however, if an interruption occurs, the BIOS could be damaged. Table 38 lists the drives and media types that can and cannot be used for BIOS recovery. The BIOS recovery media does not need to be made bootable. Table 38. Acceptable Drives/Media Types for BIOS Recovery Media Type Can be used for BIOS recovery? CD-ROM drive connected to the SATA interface Yes USB removable drive (a USB Flash Drive, for example) Yes USB diskette drive (with a 1.44 MB diskette) No USB hard disk drive No For information about Refer to BIOS update instructions http://www.intel.com/support/motherboards/desktop/sb/ CS-022312.htm 69 Intel Desktop Board D510MO Technical Product Specification 3.6.2 Custom Splash Screen ® During POST, an Intel splash screen is displayed by default. This splash screen can ® be augmented with a custom splash screen. The Intel Integrator’s Toolkit that is available from Intel can be used to create a custom splash screen. NOTE If you add a custom splash screen, it will share space with the Intel branded logo. Refer to For information about Intel Integrator Toolkit http://developer.intel.com/design/motherbd/software/itk/ 3.7 Boot Options In the BIOS Setup program, the user can choose to boot from optical drives, hard drives, removable media or the network. The default setting is for the optical drive to be the first boot device, the hard drive second, and removable media third. If enabled, the last default boot device is the network. 3.7.1 CD-ROM Boot Booting from CD-ROM is supported in compliance to the El Torito bootable CD-ROM format specification. Under the Boot menu in the BIOS Setup program, ATAPI CD-ROM is listed as a boot device. Boot devices are defined in priority order. Accordingly, if there is not a bootable CD in the CD-ROM drive, the system will attempt to boot from the next defined drive. 3.7.2 Network Boot The network can be selected as a boot device. This selection allows booting from the onboard LAN or a network add-in card with a remote boot ROM installed. Pressing the key during POST automatically forces booting from the LAN. To use this key during POST, the User Access Level in the BIOS Setup program's Security menu must be set to Full. 70 Overview of BIOS Features 3.7.3 Booting Without Attached Devices For use in embedded applications, the BIOS has been designed so that after passing the POST, the operating system loader is invoked even if the following devices are not present: • Video adapter • Keyboard • Mouse 3.7.4 Changing the Default Boot Device During POST Pressing the key during POST causes a boot device menu to be displayed. This menu displays the list of available boot devices (as set in the BIOS setup program’s Boot Device Priority submenu). Table 39 lists the boot device menu options. Table 39. Boot Device Menu Options Boot Device Menu Function Keys Description <↑> or <↓> Selects a default boot device Exits the menu, saves changes, and boots from the selected device Exits the menu without saving changes 71 Intel Desktop Board D510MO Technical Product Specification 3.8 BIOS Security Features The BIOS includes security features that restrict access to the BIOS Setup program and who can boot the computer. A supervisor password and a user password can be set for the BIOS Setup program and for booting the computer, with the following restrictions: • The supervisor password gives unrestricted access to view and change all the Setup options in the BIOS Setup program. This is the supervisor mode. • The user password gives restricted access to view and change Setup options in the BIOS Setup program. This is the user mode. • If only the supervisor password is set, pressing the key at the password prompt of the BIOS Setup program allows the user restricted access to Setup. • If both the supervisor and user passwords are set, users can enter either the supervisor password or the user password to access Setup. Users have access to Setup respective to which password is entered. • Setting the user password restricts who can boot the computer. The password prompt will be displayed before the computer is booted. If only the supervisor password is set, the computer boots without asking for a password. If both passwords are set, the user can enter either password to boot the computer. • For enhanced security, use different passwords for the supervisor and user passwords. • Valid password characters are A-Z, a-z, and 0-9. Passwords may be up to 16 characters in length. Table 40 shows the effects of setting the supervisor password and user password. This table is for reference only and is not displayed on the screen. Table 40. Supervisor and User Password Functions Password Password Password Supervisor to Enter During Set Mode User Mode Setup Options Setup Boot Neither Can change all Can change all None None None (Note) (Note) options options Supervisor Can change all Can change a Supervisor Password Supervisor None only options limited number of options User only N/A Can change all Enter Password User User options Clear User Password Supervisor Can change all Can change a Supervisor Password Supervisor or Supervisor or and user set options limited number Enter Password user user of options Note: If no password is set, any user can change all Setup options. 72 4 Board Status and Error Messages 4.1 BIOS Beep Codes Whenever a recoverable error occurs during POST, the BIOS causes the board’s speaker to beep an error message describing the problem (see Table 41). Table 41. BIOS Beep Codes Type Pattern Frequency F2 Setup/F10 Boot Menu One 0.5 second beep when BIOS is ready to 932 Hz Prompt accept keyboard input BIOS update in progress None Video error On-off (1.0 second each) two times, then 932 Hz 2.5-second pause (off), entire pattern repeats When no VGA option ROM is (beeps and pause) once and the BIOS will found. continue to boot. Memory error On-off (1.0 second each) three times, then 932 Hz 2.5-second pause (off), entire pattern repeats (beeps and pause) until the system is powered off. Thermal trip warning Alternate high and low beeps (1.0 second each) High beep 2000 Hz for 8 beeps, followed by system shut down. Low beep 1500 Hz 73 Intel Desktop Board D510MO Technical Product Specification 4.2 Front-panel Power LED Blink Codes Whenever a recoverable error occurs during POST, the BIOS causes the board’s front panel power LED to blink an error message describing the problem (see Table 42). Table 42. Front-panel Power LED Blink Codes Type Pattern Note F2 Setup/F10 Boot Menu None Prompt BIOS update in progress Off when the update begins, then on for 0.5 seconds, then off for 0.5 seconds. The pattern repeats until the BIOS update is complete. Video error On-off (1.0 second each) two times, then When no VGA option ROM is 2.5-second pause (off), entire pattern repeats found. (blink and pause) until the system is powered off. Memory error On-off (1.0 second each) three times, then 2.5-second pause (off), entire pattern repeats (blinks and pause) until the system is powered off. Thermal trip warning Each beep will be accompanied by the following blink pattern: .25 seconds On, .25 seconds Off, .25 seconds On, .25 seconds Off. This will result in a total of 16 blinks. 4.3 BIOS Error Messages Whenever a recoverable error occurs during POST, the BIOS displays an error message describing the problem. Table 43 lists the error messages and provides a brief description of each. Table 43. BIOS Error Messages Error Message Explanation CMOS Battery Low The battery may be losing power. Replace the battery soon. CMOS Checksum Bad The CMOS checksum is incorrect. CMOS memory may have been corrupted. Run Setup to reset values. Memory Size Decreased Memory size has decreased since the last boot. If no memory was removed, then memory may be bad. No Boot Device Available System did not find a device to boot. 74 Board Status and Error Messages 4.4 Port 80h POST Codes During the POST, the BIOS generates diagnostic progress codes (POST codes) to I/O port 80h. If the POST fails, execution stops and the last POST code generated is left at port 80h. This code is useful for determining the point where an error occurred. Displaying the POST codes requires a PCI bus add-in card, often called a POST card. The POST card can decode the port and display the contents on a medium such as a seven-segment display. NOTE The POST card must be installed in PCI bus connector 1. The following tables provide information about the POST codes generated by the BIOS: • Table 44 lists the Port 80h POST code ranges • Table 45 lists the Port 80h POST codes themselves • Table 46 lists the Port 80h POST sequence NOTE In the tables listed above, all POST codes and range values are listed in hexadecimal. Table 44. Port 80h POST Code Ranges Range Category/Subsystem 00 – 0F Debug codes: Can be used by any PEIM/driver for debug. 10 – 1F Host Processors: 1F is an unrecoverable CPU error. 20 – 2F Memory/Chipset: 2F is no memory detected or no useful memory detected. 30 – 3F Recovery: 3F indicated recovery failure. 40 – 4F Reserved for future use. 50 – 5F I/O Busses: PCI, USB, ISA, ATA, etc. 5F is an unrecoverable error. Start with PCI. 60 – 6F Reserved for future use (for new busses). 70 – 7F Output Devices: All output consoles. 7F is an unrecoverable error. 80 – 8F Reserved for future use (new output console codes). 90 – 9F Input devices: Keyboard/Mouse. 9F is an unrecoverable error. A0 – AF Reserved for future use (new input console codes). B0 – BF Boot Devices: Includes fixed media and removable media. BF is an unrecoverable error. C0 – CF Reserved for future use. D0 – DF Boot device selection. E0 – FF E0 – EE: Miscellaneous codes. See Table 45. EF: boot/S3 resume failure. F0 – FF: FF processor exception. 75 Intel Desktop Board D510MO Technical Product Specification Table 45. Port 80h POST Codes POST Code Description of POST Operation Host Processor 10 Power-on initialization of the host processor (Boot Strap Processor) 11 Host processor cache initialization (including APs) 12 Starting Application processor initialization 13 SMM initialization Chipset 21 Initializing a chipset component Memory 22 Reading SPD from memory DIMMs 23 Detecting presence of memory DIMMs 24 Programming timing parameters in the memory controller and the DIMMs 25 Configuring memory 26 Optimizing memory settings 27 Initializing memory, such as ECC init 28 Testing memory PCI Bus 50 Enumerating PCI busses 51 Allocating resources to PCI bus 52 Hot Plug PCI controller initialization 53 – 57 Reserved for PCI Bus USB 58 Resetting USB bus 59 Reserved for USB ATA/ATAPI/SATA 5A Resetting PATA/SATA bus and all devices 5B Reserved for ATA SMBus 5C Resetting SMBus 5D Reserved for SMBus Local Console 70 Resetting the VGA controller 71 Disabling the VGA controller 72 Enabling the VGA controller Remote Console 78 Resetting the console controller 79 Disabling the console controller 7A Enabling the console controller continued 76 Board Status and Error Messages Table 45. Port 80h POST Codes (continued) POST Code Description of POST Operation Keyboard (PS/2 or USB) 90 Resetting keyboard 91 Disabling keyboard 92 Detecting presence of keyboard 93 Enabling the keyboard 94 Clearing keyboard input buffer 95 Instructing keyboard controller to run Self Test (PS/2 only) Mouse (PS/2 or USB) 98 Resetting mouse 99 Disabling mouse 9A Detecting presence of mouse 9B Enabling mouse Fixed Media B0 Resetting fixed media B1 Disabling fixed media B2 Detecting presence of a fixed media (hard drive detection etc.) B3 Enabling/configuring a fixed media Removable Media B8 Resetting removable media B9 Disabling removable media BA Detecting presence of a removable media (CD-ROM detection, etc.) BC Enabling/configuring a removable media BDS Dy Trying boot selection y (y=0 to 15) PEI Core E0 Started dispatching PEIMs (emitted on first report of EFI_SW_PC_INIT_BEGIN EFI_SW_PEI_PC_HANDOFF_TO_NEXT) E2 Permanent memory found E1, E3 Reserved for PEI/PEIMs DXE Core E4 Entered DXE phase E5 Started dispatching drivers E6 Started connecting drivers continued 77 Intel Desktop Board D510MO Technical Product Specification Table 45. Port 80h POST Codes (continued) POST Code Description of POST Operation DXE Drivers E7 Waiting for user input E8 Checking password E9 Entering BIOS setup EB Calling Legacy Option ROMs Runtime Phase/EFI OS Boot F4 Entering Sleep state F5 Exiting Sleep state F8 EFI boot service ExitBootServices ( ) has been called F9 EFI runtime service SetVirtualAddressMap ( ) has been called FA EFI runtime service ResetSystem ( ) has been called PEIMs/Recovery 30 Crisis Recovery has initiated per user request 31 Crisis Recovery has initiated by software (corrupt flash) 34 Loading recovery capsule 35 Handing off control to the recovery capsule 3F Unable to recover 78 Board Status and Error Messages Table 46. Typical Port 80h POST Sequence POST Code Description 21 Initializing a chipset component 22 Reading SPD from memory DIMMs 23 Detecting presence of memory DIMMs 25 Configuring memory 28 Testing memory 34 Loading recovery capsule E4 Entered DXE phase 12 Starting application processor initialization 13 SMM initialization 50 Enumerating PCI busses 51 Allocating resourced to PCI bus 92 Detecting the presence of the keyboard 90 Resetting keyboard 94 Clearing keyboard input buffer 95 Keyboard Self Test EB Calling Video BIOS 58 Resetting USB bus 5A Resetting PATA/SATA bus and all devices 92 Detecting the presence of the keyboard 90 Resetting keyboard 94 Clearing keyboard input buffer 5A Resetting PATA/SATA bus and all devices 28 Testing memory 90 Resetting keyboard 94 Clearing keyboard input buffer E7 Waiting for user input 01 INT 19 00 Ready to boot 79 Intel Desktop Board D510MO Technical Product Specification 80 5 Regulatory Compliance and Battery Disposal Information 5.1 Regulatory Compliance This section contains the following regulatory compliance information for Intel Desktop Board D510MO: • Safety standards • European Union Declaration of Conformity statement • Product Ecology statements • Electromagnetic Compatibility (EMC) standards • Product certification markings 5.1.1 Safety Standards Intel Desktop Board D510MO complies with the safety standards stated in Table 47 when correctly installed in a compatible host system. Table 47. Safety Standards Standard Title CSA/UL 60950-1, First Edition Information Technology Equipment – Safety - Part 1: General Requirements (USA and Canada) EN 60950-1:2006, Second Information Technology Equipment – Safety - Part 1: General Edition Requirements (European Union) IEC 60950-1:2005, Second Information Technology Equipment – Safety - Part 1: General Edition Requirements (International) 81 Intel Desktop Board D510MO Technical Product Specification 5.1.2 European Union Declaration of Conformity Statement ® We, Intel Corporation, declare under our sole responsibility that the product Intel Desktop Board D510MO is in conformity with all applicable essential requirements necessary for CE marking, following the provisions of the European Council Directive 2004/108/EC (EMC Directive) and 2006/95/EC (Low Voltage Directive). The product is properly CE marked demonstrating this conformity and is for distribution within all member states of the EU with no restrictions. This product follows the provisions of the European Directives 2004/108/EC and 2006/95/EC. Čeština Tento výrobek odpovídá požadavkům evropských směrnic 2004/108/EC a 2006/95/EC. Dansk Dette produkt er i overensstemmelse med det europæiske direktiv 2004/108/EC & 2006/95/EC. Dutch Dit product is in navolging van de bepalingen van Europees Directief 2004/108/EC & 2006/95/EC. Eesti Antud toode vastab Euroopa direktiivides 2004/108/EC ja 2006/95/EC kehtestatud nõuetele. Suomi Tämä tuote noudattaa EU-direktiivin 2004/108/EC & 2006/95/EC määräyksiä. Français Ce produit est conforme aux exigences de la Directive Européenne 2004/108/EC & 2006/95/EC. Deutsch Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie 2004/108/EC & 2006/95/EC. Ελληνικά Το παρόν προϊόν ακολουθεί τις διατάξεις των Ευρωπαϊκών Οδηγιών 2004/108/EC και 2006/95/EC. Magyar E termék megfelel a 2004/108/EC és 2006/95/EC Európai Irányelv előírásainak. Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer 2004/108/EC & 2006/95/EC. Italiano Questo prodotto è conforme alla Direttiva Europea 2004/108/EC & 2006/95/EC. Latviešu Šis produkts atbilst Eiropas Direktīvu 2004/108/EC un 2006/95/EC noteikumiem. Lietuvių Šis produktas atitinka Europos direktyvų 2004/108/EC ir 2006/95/EC nuostatas. Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej 2004/108/EC u 2006/95/EC. Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 2004/108/EC & 2006/95/EC. Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej 2004/108/EC i 73/23/EWG. Portuguese Este produto cumpre com as normas da Diretiva Européia 2004/108/EC & 2006/95/EC. 82 Regulatory Compliance and Battery Disposal Information Español Este producto cumple con las normas del Directivo Europeo 2004/108/EC & 2006/95/EC. Slovensky Tento produkt je v súlade s ustanoveniami európskych direktív 2004/108/EC a 2006/95/EC. Slovenščina Izdelek je skladen z določbami evropskih direktiv 2004/108/EC in 2006/95/EC. Svenska Denna produkt har tillverkats i enlighet med EG-direktiv 2004/108/EC & 2006/95/EC. Türkçe Bu ürün, Avrupa Birliği’nin 2004/108/EC ve 2006/95/EC yönergelerine uyar. 5.1.3 Product Ecology Statements The following information is provided to address worldwide product ecology concerns and regulations. 5.1.3.1 Disposal Considerations This product contains the following materials that may be regulated upon disposal: lead solder on the printed wiring board assembly. 5.1.3.2 Recycling Considerations As part of its commitment to environmental responsibility, Intel has implemented the Intel Product Recycling Program to allow retail consumers of Intel’s branded products to return used products to selected locations for proper recycling. Please consult the http://www.intel.com/intel/other/ehs/product_ecology for the details of this program, including the scope of covered products, available locations, shipping instructions, terms and conditions, etc. 中文 作为其对环境责任之承诺的部分，英特尔已实施 Intel Product Recycling Program （英特尔产品回收计划），以允许英特尔品牌产品的零售消费者将使用过的产品退还至指定地点作 恰当的重复使用处理。 请参考http://www.intel.com/intel/other/ehs/product_ecology 了解此计划的详情，包括涉及产品之范围、回收地点、运送指导、条款和条件等。 Deutsch Als Teil von Intels Engagement für den Umweltschutz hat das Unternehmen das Intel Produkt-Recyclingprogramm implementiert, das Einzelhandelskunden von Intel Markenprodukten ermöglicht, gebrauchte Produkte an ausgewählte Standorte für ordnungsgemäßes Recycling zurückzugeben. Details zu diesem Programm, einschließlich der darin eingeschlossenen Produkte, verfügbaren Standorte, Versandanweisungen, Bedingungen usw., finden Sie auf der http://www.intel.com/intel/other/ehs/product_ecology 83 Intel Desktop Board D510MO Technical Product Specification Español Como parte de su compromiso de responsabilidad medioambiental, Intel ha implantado el programa de reciclaje de productos Intel, que permite que los consumidores al detalle de los productos Intel devuelvan los productos usados en los lugares seleccionados para su correspondiente reciclado. Consulte la http://www.intel.com/intel/other/ehs/product_ecology para ver los detalles del programa, que incluye los productos que abarca, los lugares disponibles, instrucciones de envío, términos y condiciones, etc. Français Dans le cadre de son engagement pour la protection de l'environnement, Intel a mis en œuvre le programme Intel Product Recycling Program (Programme de recyclage des produits Intel) pour permettre aux consommateurs de produits Intel de recycler les produits usés en les retournant à des adresses spécifiées. Visitez la page Web http://www.intel.com/intel/other/ehs/product_ecology pour en savoir plus sur ce programme, à savoir les produits concernés, les adresses disponibles, les instructions d'expédition, les conditions générales, etc. 日本語 インテルでは、環境保護活動の一環として、使い終えたインテル ブランド製品を指定の場所へ返送していただき、リサイクルを適切に行えるよう、インテル製品リサイクル プログラムを発足させました。 対象製品、返送先、返送方法、ご利用規約など、このプログラムの詳細情報は、http://www.intel.com/in tel/other/ehs/product_ecology （英語）をご覧ください。 Malay Sebagai sebahagian daripada komitmennya terhadap tanggungjawab persekitaran, Intel telah melaksanakan Program Kitar Semula Produk untuk membenarkan pengguna-pengguna runcit produk jenama Intel memulangkan produk terguna ke lokasi-lokasi terpilih untuk dikitarkan semula dengan betul. Sila rujuk http://www.intel.com/intel/other/ehs/product_ecology untuk mendapatkan butir-butir program ini, termasuklah skop produk yang dirangkumi, lokasi-lokasi tersedia, arahan penghantaran, terma & syarat, dsb. Portuguese Como parte deste compromisso com o respeito ao ambiente, a Intel implementou o Programa de Reciclagem de Produtos para que os consumidores finais possam enviar produtos Intel usados para locais selecionados, onde esses produtos são reciclados de maneira adequada. Consulte o site http://www.intel.com/intel/other/ehs/product_ecology (em Inglês) para obter os detalhes sobre este programa, inclusive o escopo dos produtos cobertos, os locais disponíveis, as instruções de envio, os termos e condições, etc. 84 Regulatory Compliance and Battery Disposal Information Russian В качестве части своих обязательств к окружающей среде, в Intel создана программа утилизации продукции Intel (Product Recycling Program) для предоставления конечным пользователям марок продукции Intel возможности возврата используемой продукции в специализированные пункты для должной утилизации. Пожалуйста, обратитесь на веб-сайт http://www.intel.com/intel/other/ehs/product_ecology за информацией об этой программе, принимаемых продуктах, местах приема, инструкциях об отправке, положениях и условиях и т.д. Türkçe Intel, çevre sorumluluğuna bağımlılığının bir parçası olarak, perakende tüketicilerin Intel markalı kullanılmış ürünlerini belirlenmiş merkezlere iade edip uygun şekilde geri dönüştürmesini amaçlayan Intel Ürünleri Geri Dönüşüm Programı’nı uygulamaya koymuştur. Bu programın ürün kapsamı, ürün iade merkezleri, nakliye talimatları, kayıtlar ve şartlar v.s dahil bütün ayrıntılarını ögrenmek için lütfen http://www.intel.com/intel/other/ehs/product_ecology Web sayfasına gidin. 5.1.3.3 Lead Free Intel Desktop Board This Intel Desktop Board is a European Union Restriction of Hazardous Substances (EU RoHS Directive 2002/95/EC) compliant product. EU RoHS restricts the use of six materials. One of the six restricted materials is lead. This Intel Desktop Board is lead free although certain discrete components used on the board contain a small amount of lead which is necessary for component performance and/or reliability. This Intel Desktop Board is referred to as “Lead-free second level interconnect.” The board substrate and the solder connections from the board to the components (second-level connections) are all lead free. China bans the same substances and has the same limits as EU RoHS; however it requires different product marking and controlled substance information. The required mark shows the Environmental Friendly Usage Period (EFUP). The EFUP is defined as the number of years for which controlled listed substances will not leak or chemically deteriorate while in the product. nd Table 48 shows the various forms of the “Lead-Free 2 Level Interconnect” mark as it appears on the board and accompanying collateral. 85 Intel Desktop Board D510MO Technical Product Specification Table 48. Lead-Free Board Markings Description Mark nd Lead-Free 2 Level Interconnect: This symbol is used to identify electrical and electronic assemblies and components in which the lead (Pb) concentration level in the board substrate and the solder connections from the or board to the components (second- level interconnect) is not greater than 0.1% by weight (1000 ppm). or 86 Regulatory Compliance and Battery Disposal Information 5.1.4 EMC Regulations Intel Desktop Board D510MO complies with the EMC regulations stated in Table 49 when correctly installed in a compatible host system. Table 49. EMC Regulations Regulation Title FCC 47 CFR Part 15, Title 47 of the Code of Federal Regulations, Part15, Subpart B, Radio Subpart B Frequency Devices. (USA) ICES-003 Issue 4 Interference-Causing Equipment Standard, Digital Apparatus. (Canada) EN55022:2006 Limits and methods of measurement of Radio Interference Characteristics of Information Technology Equipment. (European Union) EN55024:1998 Information Technology Equipment – Immunity Characteristics Limits and methods of measurement. (European Union) EN55022:2006 Australian Communications Authority, Standard for Electromagnetic Compatibility. (Australia and New Zealand) CISPR 22:2005 Limits and methods of measurement of Radio Disturbance Characteristics of +A1:2005 +A2:2006 Information Technology Equipment. (International) CISPR 24:1997 Information Technology Equipment – Immunity Characteristics – Limits and +A1:2001 +A2:2002 Methods of Measurement. (International) VCCI V-3/2007.04, Voluntary Control for Interference by Information Technology Equipment. V-4/2007.04 (Japan) KN-22, KN-24 Korean Communications Commission – Framework Act on Telecommunications and Radio Waves Act (South Korea) CNS 13438:2006 Bureau of Standards, Metrology and Inspection (Taiwan) Japanese Kanji statement translation: this is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. 87 Intel Desktop Board D510MO Technical Product Specification Korean Class B statement translation: this is household equipment that is certified to comply with EMC requirements. You may use this equipment in residential environments and other non-residential environments. 5.1.5 Product Certification Markings (Board Level) Intel Desktop Board D510MO has the product certification markings shown in Table 50: Table 50. Product Certification Markings Description Mark UL joint US/Canada Recognized Component mark. Includes adjacent UL file number for Intel Desktop Boards: E210882. FCC Declaration of Conformity logo mark for Class B equipment. Includes Intel name and D510MO model designation. CE mark. Declaring compliance to European Union (EU) EMC directive and Low Voltage directive. Australian Communications Authority (ACA) and New Zealand Radio Spectrum Management (NZ RSM) C-tick mark. Includes adjacent Intel supplier code number, N-232. Japan VCCI (Voluntary Control Council for Interference) mark. Korea Certification mark. Includes an adjacent KCC (Korean Communications Commission) certification number: KCC-REM-CPU-D510MO Taiwan BSMI (Bureau of Standards, Metrology and Inspections) mark. Includes adjacent Intel company number, D33025. Printed wiring board manufacturer’s recognition mark. Consists of a unique V-0 UL recognized manufacturer’s logo, along with a flammability rating (solder side). China RoHS/Environmentally Friendly Use Period Logo: This is an example of the symbol used on Intel Desktop Boards and associated collateral. The color of the mark may vary depending upon the application. The Environmental Friendly Usage Period (EFUP) for Intel Desktop Boards has been determined to be 10 years. 88 Regulatory Compliance and Battery Disposal Information 5.2 Battery Disposal Information CAUTION Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations. PRECAUTION Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect. Les piles usagées doivent être recyclées dans la mesure du possible. La mise au rebut des piles usagées doit respecter les réglementations locales en vigueur en matière de protection de l'environnement. FORHOLDSREGEL Eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. Batterier bør om muligt genbruges. Bortskaffelse af brugte batterier bør foregå i overensstemmelse med gældende miljølovgivning. OBS! Det kan oppstå eksplosjonsfare hvis batteriet skiftes ut med feil type. Brukte batterier bør kastes i henhold til gjeldende miljølovgivning. VIKTIGT! Risk för explosion om batteriet ersätts med felaktig batterityp. Batterier ska kasseras enligt de lokala miljövårdsbestämmelserna. VARO Räjähdysvaara, jos pariston tyyppi on väärä. Paristot on kierrätettävä, jos se on mahdollista. Käytetyt paristot on hävitettävä paikallisten ympäristömääräysten mukaisesti. VORSICHT Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie darf nur durch denselben oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt werden. Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend. AVVERTIMENTO Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto. Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per disfarsi delle pile usate, seguire le istruzioni del produttore. 89 Intel Desktop Board D510MO Technical Product Specification PRECAUCIÓN Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo. Para deshacerse de las pilas usadas, siga igualmente las instrucciones del fabricante. WAARSCHUWING Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type batterij. Batterijen moeten zoveel mogelijk worden gerecycled. Houd u bij het weggooien van gebruikte batterijen aan de plaatselijke milieuwetgeving. ATENÇÃO Haverá risco de explosão se a bateria for substituída por um tipo de bateria incorreto. As baterias devem ser recicladas nos locais apropriados. A eliminação de baterias usadas deve ser feita de acordo com as regulamentações ambientais da região. AŚCIAROŽZNAŚĆ Існуе рызыка выбуху, калі заменены акумулятар неправільнага тыпу. Акумулятары павінны, па магчымасці, перепрацоўвацца. Пазбаўляцца ад старых акумулятараў патрэбна згодна з мясцовым заканадаўствам па экалогіі. UPOZORNÌNÍ V případě výměny baterie za nesprávný druh může dojít k výbuchu. Je-li to možné, baterie by měly být recyklovány. Baterie je třeba zlikvidovat v souladu s místními předpisy o životním prostředí. Προσοχή Υπάρχει κίνδυνος για έκρηξη σε περίπτωση που η μπαταρία αντικατασταθεί από μία λανθασμένου τύπου. Οι μπαταρίες θα πρέπει να ανακυκλώνονται όταν κάτι τέτοιο είναι δυνατό. Η απόρριψη των χρησιμοποιημένων μπαταριών πρέπει να γίνεται σύμφωνα με τους κατά τόπο περιβαλλοντικούς κανονισμούς. VIGYAZAT Ha a telepet nem a megfelelő típusú telepre cseréli, az felrobbanhat. A telepeket lehetőség szerint újra kell hasznosítani. A használt telepeket a helyi környezetvédelmi előírásoknak megfelelően kell kiselejtezni. 90 Regulatory Compliance and Battery Disposal Information AWAS Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri sepatutnya dikitar semula jika boleh. Pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan. OSTRZEŻENIE Istnieje niebezpieczeństwo wybuchu w przypadku zastosowania niewłaściwego typu baterii. Zużyte baterie należy w miarę możliwości utylizować zgodnie z odpowiednimi przepisami ochrony środowiska. PRECAUŢIE Risc de explozie, dacă bateria este înlocuită cu un tip de baterie necorespunzător. Bateriile trebuie reciclate, dacă este posibil. Depozitarea bateriilor uzate trebuie să respecte reglementările locale privind protecţia mediului. ВНИМАНИЕ При использовании батареи несоответствующего типа существует риск ее взрыва. Батареи должны быть утилизированы по возможности. Утилизация батарей должна проводится по правилам, соответствующим местным требованиям. UPOZORNENIE Ak batériu vymeníte za nesprávny typ, hrozí nebezpečenstvo jej výbuchu. Batérie by sa mali podľa možnosti vždy recyklovať. Likvidácia použitých batérií sa musí vykonávať v súlade s miestnymi predpismi na ochranu životného prostredia. POZOR Zamenjava baterije z baterijo drugačnega tipa lahko povzroči eksplozijo. Če je mogoče, baterije reciklirajte. Rabljene baterije zavrzite v skladu z lokalnimi okoljevarstvenimi predpisi. . UYARI Yanlış türde pil takıldığında patlama riski vardır. Piller mümkün olduğunda geri dönüştürülmelidir. Kullanılmış piller, yerel çevre yasalarına uygun olarak atılmalıdır. OСТОРОГА Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху. Якщо можливо, використані батареї слід утилізувати. Утилізація використаних батарей має бути виконана згідно місцевих норм, що регулюють охорону довкілля. 91 Intel Desktop Board D510MO Technical Product Specification 92