Elite.Parts Manufacturers I INFINEON TECHNOLOGIES BTS442E2
About product Datasheet FAQ

INFINEON TECHNOLOGIES BTS442E2

Description

SWITCH HIGH SIDE POWER TO220AB-5

Part Number

BTS442E2

Price

Request Quote

Manufacturer

INFINEON TECHNOLOGIES

Lead Time

Request Quote

Category

PRODUCTS - B

Datasheet

pdf file

2530715_1.pdf

305 KiB

Extracted Text

® PROFET BTS 442 E2 Smart Highside Power Switch Features Product Summary • Overload protection Overvoltage protection V 63 V bb(AZ) • Current limitation V 4.5 ... 42 V Operating voltage bb(on) • Short-circuit protection On-state resistance R 18 • ON mΩ Thermal shutdown • Overvoltage protection (including load dump) Load current (ISO) I 21 A L(ISO) • Fast demagnetization of inductive loads Current limitation IL(SCr) 70 A 1 • ) Reverse battery protection • Undervoltage and overvoltage shutdown with TO-220AB/5 auto-restart and hysteresis • Open drain diagnostic output • Open load detection in ON-state 5 • CMOS compatible input 5 5 2) • Loss of ground and loss of V protection bb 1 1 1 • Electrostatic discharge (ESD) protection SMD Straight leads Standard Application • µC compatible power switch with diagnostic feedback for 12 V and 24 V DC grounded loads • All types of resistive, inductive and capacitve loads • Replaces electromechanical relays and discrete circuits General Description N channel vertical power FET with charge pump, ground referenced CMOS compatible input and diagnostic  feedback, integrated in Smart SIPMOS chip on chip technology. Fully protected by embedded protection functions. + V R bb bb 3 Voltage Overvoltage Current Gate source protection limit protection V Logic OUT Charge pump Limit for Voltage unclamped 5 sensor Level shifter Temperature ind. loads sensor Rectifier IN 2 Open load Load Logic ESD detection 4 ST Short circuit detection  PROFET GND 1 Load GND Signal GND 1) No external components required, reverse load current limited by connected load. 2) Additional external diode required for charged inductive loads Infineon Technologies AG 1 22.03.99 ® PROFET BTS 442 E2 Pin Symbol Function 1 GND - Logic ground 2 IN I Input, activates the power switch in case of logical high signal 3V + Positive power supply voltage, bb the tab is shorted to this pin 4 ST S Diagnostic feedback, low on failure 5 OUT O Output to the load (Load, L) Maximum Ratings at Tj = 25 °C unless otherwise specified Parameter Symbol Values Unit Supply voltage (overvoltage protection see page 3) V 63 V bb 3) Load dump protection V = U + V , U = 13.5 V V 80 V LoadDump A s A Load dump R = 2 Ω, R = 1.1 Ω, t = 200 ms, IN= low or high I L d Load current (Short-circuit current, see page 4) I self-limited A L Operating temperature range T -40 ...+150 °C j Storage temperature range T -55 ...+150 stg Power dissipation (DC) P 167 W tot Inductive load switch-off energy dissipation, single pulse T=150 °C: E 2.1 J j AS Electrostatic discharge capability (ESD) V 2.0 kV ESD (Human Body Model) Input voltage (DC) V -0.5 ... +6 V IN Current through input pin (DC) I ±5.0 mA IN Current through status pin (DC) I ±5.0 ST see internal circuit diagrams page 6... Thermal resistance chip - case: R ≤ 0.75 K/W thJC ≤ 75 junction - ambient (free air): R thJA 4) SMD version, device on pcb : ≤ tbd 3) V is setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839 Load dump 2 4) Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm (one layer, 70µm thick) copper area for V bb connection. PCB is vertical without blown air. Infineon Technologies AG 2 22.03.99 ® PROFET BTS 442 E2 Electrical Characteristics Parameter and Conditions Symbol Values Unit at Tj = 25 °C, V = 12 V unless otherwise specified bb min typ max Load Switching Capabilities and Characteristics On-state resistance (pin 3 to 5) I = 5 A T=25 °C: R -- 15 18 L j ON mΩ T=150 °C: 28 35 j Nominal load current (pin 3 to 5) I 17 21 -- A L(ISO) ISO Proposal: V = 0.5 V, T = 85 °C ON C Output current (pin 5) while GND disconnected or I -- -- 1 mA L(GNDhigh) GND pulled up, V = 0, see diagram page 7, IN T =-40...+150°C j Turn-on time to 90% V : t 100 -- 350 µs OUT on Turn-off time to 10% V : t 10 -- 130 OUT off R = 12 Ω, T =-40...+150°C L j Slew rate on dV /dt 0.2 -- 2 V/µs on 10 to 30% V , R = 12 Ω, T =-40...+150°C OUT L j Slew rate off -dV/dt 0.4 -- 5 V/µs off 70 to 40% V , R = 12 Ω, T =-40...+150°C OUT L j Operating Parameters 5) Operating voltage T =-40...+150°C: V 4.5 -- 42 V j bb(on) Undervoltage shutdown T =-40...+150°C: V 2.4 -- 4.5 V j bb(under) Undervoltage restart T =-40...+150°C: V -- -- 4.5 V j bb(u rst) Undervoltage restart of charge pump V -- 6.5 7.5 V bb(ucp) see diagram page 12 T =-40...+150°C: j Undervoltage hysteresis ∆V -- 0.2 -- V bb(under) ∆V = V - V bb(under) bb(u rst) bb(under) Overvoltage shutdown T =-40...+150°C: V 42 -- 52 V j bb(over) Overvoltage restart T =-40...+150°C: V 42 -- -- V j bb(o rst) Overvoltage hysteresis T =-40...+150°C: ∆V -- 0.2 -- V j bb(over) 6) Overvoltage protection T =-40°C: V 60 -- -- V j bb(AZ) 63 67 I =40 mA T =25...+150°C: bb j Standby current (pin 3) T =-40...+25°C: I -- 12 25 µA j bb(off) V =0 T =150°C: -- 18 60 IN j I -- 6 -- µA Leakage output current (included in I ) L(off) bb(off) VIN=0 7) Operating current (Pin 1) , V =5 V I -- 1.1 -- mA IN GND 5) At supply voltage increase up to V = 6.5 V typ without charge pump, V ≈V - 2 V bb OUT bb 6) see also V in table of protection functions and circuit diagram page 7. Meassured without load. ON(CL) 7) Add I , if I > 0, add I , if V >5.5 V ST ST IN IN Infineon Technologies AG 3 22.03.99 ® PROFET BTS 442 E2 Parameter and Conditions Symbol Values Unit at Tj = 25 °C, V = 12 V unless otherwise specified bb min typ max Protection Functions 8) Initial peak short circuit current limit (pin 3 to 5) , I L(SCp) ( max 400 µs if V > V ) ON ON(SC) =-40°C: -- -- 140 A Tj =25°C: -- 95 -- Tj =+150°C: 45 -- -- Tj Repetitive short circuit current limit I L(SCr) T = T (see timing diagrams, page 10) 30 70 -- A j jt Short circuit shutdown delay after input pos. slope V > V , T =-40..+150°C: t ON ON(SC) j d(SC) 80 -- 400 µs min value valid only, if input "low" time exceeds 30 µs Output clamp (inductive load switch off) at V = V - V , I = 30 mA V -- 58 -- V OUT bb ON(CL) L ON(CL) Short circuit shutdown detection voltage (pin 3 to 5) V -- 8.3 -- V ON(SC) Thermal overload trip temperature T 150 -- -- °C jt Thermal hysteresis ∆T -- 10 -- K jt 9) Inductive load switch-off energy dissipation , E -- -- 2.1 J AS T = 150 °C, single pulse V = 12 V: E 1.7 j Start bb Load12 1.2 V = 24 V: E bb Load24 10) Reverse battery (pin 3 to 1) -V -- -- 32 V bb Integrated resistor in V line R -- 120 -- Ω bb bb Diagnostic Characteristics Open load detection current T =-40 °C: I 2 -- 1900 mA j L (OL) (on-condition) T =25..150°C: 2 -- 1500 j 8) Short circuit current limit for max. duration of t =400 µs, prior to shutdown d(SC) max 9) While demagnetizing load inductance, dissipated energy in PROFET is E = V * i (t) dt, approx. AS ON(CL) L ∫ V 2 ON(CL) 1 E = / * L * I * ( ), see diagram page 8 AS 2 L V - V ON(CL) bb 10) Reverse load current (through intrinsic drain-source diode) is normally limited by the connected load. Reverse current I of ≈ 0.3 A at V = -32 V through the logic heats up the device. Time allowed under GND bb these condition is dependent on the size of the heatsink. Reverse I can be reduced by an additional GND external GND-resistor (150 Ω). Input and Status currents have to be limited (see max. ratings page 2 and circuit page 7). Infineon Technologies AG 4 22.03.99 ® PROFET BTS 442 E2 Parameter and Conditions Symbol Values Unit at Tj = 25 °C, V = 12 V unless otherwise specified bb min typ max 11) Input and Status Feedback Input turn-on threshold voltage V 1.5 -- 2.4 V IN(T+) T =-40..+150°C: j Input turn-off threshold voltage V 1.0 -- -- V IN(T-) T =-40..+150°C: j Input threshold hysteresis ∆ V -- 0.5 -- V IN(T) Off state input current (pin 2), V = 0.4 V I 1-- 30 µA IN IN(off) On state input current (pin 2), V = 3.5 V I 10 25 50 µA IN IN(on) Status invalid after positive input slope t 80 200 400 µs d(ST SC) (short circuit) T =-40 ... +150°C: j Status invalid after positive input slope t 350 -- 1600 µs d(ST) (open load) T =-40 ... +150°C: j Status output (open drain) Zener limit voltage T =-40...+150°C, I = +1.6 mA: V 5.4 6.1 -- V j ST ST(high) ST low voltage T =-40...+150°C, I = +1.6 mA: V -- -- 0.4 j ST ST(low) 11) If a ground resistor R is used, add the voltage drop across this resistor. GND Infineon Technologies AG 5 22.03.99 ® PROFET BTS 442 E2 Truth Table Input- Output Status level level 442 442 D2 E2 Normal L L H H H operation H H H 12 ) Open load L H H H H L L Short circuit L L H H to GND H L L L H Short circuit L H H 13) 13) to V H H H (L ) H (L ) bb Overtem- L L L L L perature H L L 14) Under- L L L H 14) voltage H L L H Overvoltage L L L H H L L H L = "Low" Level H = "High" Level Terms Status output +5V I bb 3 I IN V R bb ST(ON) IN ST 2 I V L ON OUT PROFET I 5 ST ESD- ST 4 ZD V GND V GND IN ST V 1 I bb V GND OUT ESD-Zener diode: 6.1 V typ., max 5 mA; R GND R < 250 Ω at 1.6 mA, ESD zener diodes are not ST(ON) to be used as voltage clamp at DC conditions. Operation in this mode may result in a drift of the zener Input circuit (ESD protection) voltage (increase of up to 1 V). R I IN ESD- ZD ZD I1 I2 I I GND ZD 6.1 V typ., ESD zener diodes are not to be used I1 as voltage clamp at DC conditions. Operation in this mode may result in a drift of the zener voltage (increase of up to 1 V). 12) Power Transistor off, high impedance 13) Low resistance short V to output may be detected by no-load-detection bb 14) No current sink capability during undervoltage shutdown Infineon Technologies AG 6 22.03.99 ® PROFET BTS 442 E2 Short Circuit detection Open-load detection Fault Condition: V > 8.3 V typ.; IN high ON-state diagnostic condition: V < R * I ; IN ON ON ON L(OL) high + V bb + V bb V ON V ON ON OUT Short circuit Logic OUT detection unit Open load Logic detection unit Inductive and overvoltage output clamp + V bb V Z GND disconnect V ON 3 OUT V bb IN GND 2 OUT PROFET 5 V clamped to 58 V typ. ON ST 4 GND Overvolt. and reverse batt. protection V V V 1 V bb IN ST GND + V bb R Any kind of load. In case of Input=high is V ≈ V - V . bb OUT IN IN(T+) V Z Due to V >0, no V = low signal available. R GND ST IN IN GND disconnect with GND pull up Logic V OUT ST R 3 ST GND PROFET V bb IN 2 R GND OUT PROFET Signal GND 5 ST R = 120 Ω typ., V +R *40 mA = 67 V typ., add 4 bb Z bb GND R , R , R for extended protection GND IN ST 1 V V V V IN ST GND bb Any kind of load. If V > V - V device stays off GND IN IN(T+) Due to V >0, no V = low signal available. GND ST Infineon Technologies AG 7 22.03.99 ® PROFET BTS 442 E2 V disconnect with charged inductive Inductive Load switch-off energy bb load dissipation E bb 3 E AS V high bb E IN Load 2 V bb IN OUT PROFET 5 OUT PROFET ST 4 = GND ST E L 1 GND V E R bb Energy dissipated in PROFET E = E + E - E . AS bb L R 3 2 1 E < E , E = / * L * I Load L L 2 L V high bb IN 2 OUT PROFET 5 ST 4 GND 1 V bb Infineon Technologies AG 8 22.03.99 ® PROFET BTS 442 E2 Options Overview all versions: High-side switch, Input protection, ESD protection, load dump and reverse battery protection , protection against loss of ground Type BTS 442D2 442E2 Logic version D E Overtemperature protection 15 16 ) ) T >150 °C, latch function X j X T >150 °C, with auto-restart on cooling j Short-circuit to GND protection 15) switches off when V >8.3 V typ. X X ON (when first turned on after approx. 200 µs) Open load detection in OFF-state with sensing current 30 µA typ. in ON-state with sensing voltage drop across X X power transistor Undervoltage shutdown with auto restart X X Overvoltage shutdown with auto restart X X Status feedback for overtemperature X X short circuit to GND X X 17) 17) - - short to V bb open load X X undervoltage X - overvoltage X - Status output type CMOS X X Open drain Output negative voltage transient limit (fast inductive load switch off) to V - V bb ON(CL) X X Load current limit high level (can handle loads with high inrush currents) X X medium level low level (better protection of application) 15) Latch except when V -V < V after shutdown. In most cases V = 0 V after shutdown (V ≠ bb OUT ON(SC) OUT OUT 0 V only if forced externally). So the device remains latched unless V < V (see page 4). No latch bb ON(SC) between turn on and t . d(SC) 16) With latch function. Reseted by a) Input low, b) Undervoltage, c) Overvoltage 17) Low resistance short V to output may be detected by no-load-detection bb Infineon Technologies AG 9 22.03.99 ® PROFET BTS 442 E2 Timing diagrams Figure 1a: V turn on: bb Figure 2b: Switching an inductive load IN IN t d(bb IN) V bb d(ST) t ST *) V OUT V OUT A ST open drain I L I L(OL) t A t in case of too early V =high the device may not turn on (curve A) IN t approx. 150 µs d(bb IN) *) if the time constant of load is too large, open-load-status may occur Figure 2a: Switching a lamp, Figure 3a: Turn on into short circuit, IN IN ST ST V OUT V OUT t d(SC) I L I L t t t approx. 200µs if V - V > 8.3 V typ. d(SC) bb OUT Infineon Technologies AG 10 22.03.99 ® PROFET BTS 442 E2 Figure 3b: Turn on into overload, Figure 4a: Overtemperature: Reset if T

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the BTS442E2 have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

product

TRANS PNP AF 20V SOT-89

product

TRANS NPN AF 45V SOT-23

product

TRANS NPN AF 45V SOT-23

product

TRANS RF NPN 15V 150MA SOT-223

product

TRANS NPN RF 4.5V SOT-343

product

TRANS NPN RF 4.5V SOT-343