Engineering Specification Engineering Specification Type 15.0 UXGA Color TFT/LCD Module Model Name: N150U3-L06 Document Control Number: OEM I-N150U3-L06 Note: Specification is subject to change without notice. Consequently it is better to contact International Display Technology before proceeding with the design of your product incorporating this module. Sales Support International Display Technology (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 1/27 Engineering Specification i Contents i Contents ii Record of Revision 1.0 Handling Precautions 2.0 General Description 2.1 Characteristics 2.2 Functional Block Diagram 3.0 Absolute Maximum Ratings 4.0 Optical Characteristics 5.0 Signal Interface 5.1 Connectors 5.2 Interface Signal Connector 5.3 Interface Signal Description 5.4 Interface Signal Electrical Characteristics 5.4.1 Signal Electrical Characteristics for LVDS Receiver 5.4.2 LVDS Receiver Internal Circuit 5.4.3 Recommended Guidelines for Motherboard PCB Design and Cable Selection 5.5 Signal for Lamp connector 6.0 Pixel format image 7.0 Parameter guide line for CFL Inverter 8.0 Interface Timings 8.1 Timing Characteristics 8.2 Timing Definition 9.0 Power Specifications 10.0 Power ON/OFF Sequence 11.0 Mechanical Characteristics 12.0 National Test Lab Requirement (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 2/27 Engineering Specification ii Record of Revision Date Document Revision Page Summary February 18, 2004 OEM I-N150U3-L06 All First Edition for customer. (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 3/27 Engineering Specification 1.0 Handling Precautions ▪ Since front polarizer is easily damaged, pay attention not to scratch it. ▪ Be sure to turn off power supply when inserting or disconnecting from input connector. ▪ Wipe off water drop immediately. Long contact with water may cause discoloration or spots. ▪ When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. ▪ Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. ▪ Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. ▪ Do not open nor modify the Module Assembly. ▪ Do not press the reflector sheet at the back of the module to any directions. ▪ Do not stick the adhesive tape on the reflector sheet at the back of the LCD module. ▪ In case if a Module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CFL Reflector edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT Module may be damaged. ▪ At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT Module. ▪ After installation of the TFT Module into an enclosure ( Notebook PC Bezel, for example), do not twist nor bent the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module may be damaged. ▪ The fluorescent lamp in the liquid crystal display (LCD) contains mercury. Do not put it in trash that is disposed of in landfills. Dispose of it as required by local ordinances or regulations. ▪ Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be supplied by power complied with requirements of Limited Power Source (2.11, IEC60950 3rd.Ed. or UL60950 3rd. Ed.), or be applied exemption conditions of flammability requirements (4.7.3.4, IEC60950 3rd.Ed. or UL60950 3rd.Ed.) in an end product. ▪ The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit (2.4, IEC60950 3rd.Ed. or UL60950 3rd.Ed.). Do not connect the CFL in Hazardous Voltage Circuit. ▪ The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by International Display Technology for any infringements of patents or other right of the third partied which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of International Display Technology or others. ▪ The information contained herein may be changed without prior notice. It is therefore advisable to contact International Display Technology before proceeding with the design of equipment incorporating this product. (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 4/27 Engineering Specification 2.0 General Description This specification applies to the Type 15.0 Color TFT/LCD Module 'N150U3-L06'. This module is designed for a display unit of notebook style personal computer. The screen format and electrical interface are intended to support the UXGA (1600(H) x 1200(V)) screen. Support color is native 262K colors (RGB 6-bit data driver). All input signals are LVDS (Low Voltage Differential Signaling) interface compatible. This module does not contain an inverter card for backlight. 2.1 Characteristics The following items are characteristics summary on the table under 25 degree C condition: CHARACTERISTICS ITEMS SPECIFICATIONS Screen Diagonal [mm] 381 Pixels H x V 1600(x3) x 1200 Active Area [mm] 304.8(H) x 228.6(V) Pixel Pitch [mm] 0.1905(per one triad) x 0.1905 Pixel Arrangement R,G,B Vertical Stripe Weight [grams] 575 Typ 600 Max. Physical Size [mm] 317.3(W) x 242.0(H) x 6.2(D) Typ./6.5(D) Max. Display Mode Normally Black Display Surface Treatment Anti-Glare Treatment Support Color Native 262K colors (RGB 6-bit data driver) 2 White Luminance [cd/m ] (center) 200 Typ. Contrast Ratio 400 : 1 Typ. Optical Rise Time + Fall Time [msec] 60 Typ., 120 Max Nominal Input Voltage VDD [Volt] +3.3 Typ. Power Consumption [Watt](VDD) 3.1 Typ., 4.4 Max. Lamp Power Consumption [Watt] 4.1 Typ., (W/o inverter loss) 4.5 Max., (W/o inverter loss) Typical Power Consumption [Watt] 7.2 Typ., 8.9 Max.(W/o inverter loss) Electrical Interface 8 pairs LVDS (Even/Odd R/G/B Data(6bit), 3sync signals, Clock) Temperature Range [degree C] Operating 0 to +50 Storage (Shipping) -20 to +60 CFL Cable Length [mm] 85 Typ Module Life 10,000 hours (same as lamp life) (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 5/27 Engineering Specification 2.2 Functional Block Diagram The following diagram shows the functional block of this Type 15.0 Color TFT/LCD Module. The first LVDS port transmits even pixels while the second LVDS port transmits odd pixels. X-Driver Y-Driver < 8 pairs LVDS > LCD DRIVE CARD 6bit color data for R/G/B EVEN PIXEL LCD TFT ARRAY/CELL (even/odd) Controller ODD 1600(R/G/B) x 1200 DTCLK(even/od PIXEL DSPTMG Dual LVDS Vsync RECEIVER Hsync G/A VEEDID CLKEEDID DC-DC EEDID DataEEDID Converter Backlight Unit Chip Ref circuit VDD GND Lamp Connector JST BHSR-02VS-1 (2pin) LCD-DRIVE Connector JAE FI-XB30SL-HF10 (30pin) (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 6/27 Engineering Specification 3.0 Absolute Maximum Ratings Absolute maximum ratings of the module is as follows: Item Symbol Min Max Unit Conditions Logic/LCD Drive Voltage VDD -0.3 +4.0 V Input Signal Voltage VIN -0.3 VDD+0.3 V CFL Ignition Voltage Vs - +2,000 Vrms Note 2 CFL Current ICFL - 7 mAms CFL Peak Inrush Current ICFLP - 20 mA Operating Temperature TOP 0 +50 deg.C Note 1 Operating Relative Humidity HOP 8 95 %RH Note 1 Storage Temperature TST -20 +60 deg.C Note 1 Storage Relative Humidity HST 5 95 %RH Note 1 Vibration 1.5 10-200 G Hz Shock 50 18 G ms Rectangle wave Note 1: Maximum Wet-Bulb should be 39 degree C and No condensation. Note 2: Duration: 50msec Max. Ta=0 degree C (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 7/27 Engineering Specification 4.0 Optical Characteristics The optical characteristics are measured under stable conditions as follows under 25 degree C condition: Item Conditions Specification Typ. Note Viewing Angle Horizontal (Right) 85 - (Degrees) K>10 (Left) 85 - Vertical (Upper) 85 - K: Contrast Ratio K>10 (Lower) 85 - Contrast ratio 400 - Response Time (ms) Rising + Falling 60 - Color Red x 0.569 - Chromaticity Red y 0.332 - (CIE) Green x 0.312 - Green y 0.544 - Blue x 0.149 - Blue y 0.132 - White x 0.313 - White y 0.329 - 2 White Luminance (cd/m ) Icfl=6.5mA 200 Typ. - (Center) 185 Typ. (5point average) (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 8/27 Engineering Specification 5.0 Signal Interface 5.1 Connectors Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. Connector Name / Designation For Signal Connector Manufacturer JAE Type / Part Number FI-XB30SL-HF10 Mating Receptacle Manufacture JAE Mating Receptacle/Part Number FI-X30M Connector Name / Designation For Lamp Connector Manufacturer JST Type / Part Number BHSR-02VS-1 Mating Type / Part Number SM02B-BHSS-1 (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 9/27 Engineering Specification 5.2 Interface Signal Connector Pin # Signal Name Pin # Signal Name 1 GND 16 GND 2 VDD 17 ReCLKIN- 3 VDD 18 ReCLKIN+ 4 V (Note 2,3) 19 GND EEDID 5 Reserved (Note 1) 20 RoIN0- 6 CLK (Note 2,4) 21 RoIN0+ EEDID 7 Data (Note 2,4) 22 GND EEDID 8 ReIN0- 23 RoIN1- 9 ReIN0+ 24 RoIN1+ 10 GND 25 GND 11 ReIN1- 26 RoIN2- 12 ReIN1+ 27 RoIN2+ 13 GND 28 GND 14 ReIN2- 29 RoCLKIN- 15 ReIN2+ 30 RoCLKIN+ Note: 1. 'Reserved' pins are not allowed to connect any other line. 2. This LCD Module complies with "VESA ENHANCED EXTENDED DISPLAY IDENTIFICATION DATA STANDARD Release A, Revision 1" and supports "EEDID version 1.3". This module uses Serial EEPROM AT24C02-10TI-2.7 (ATMEL) or compatible as a EEDID function. 3. V power source shall be the current limited circuit which has not exceeding 1A. (Reference Document: EEDID TM "Enhanced Display Data Channel (E-DDC ) Proposed Standard", VESA) 4. Both CLK line and Data line are pulled-up with 10K ohm resistor to V power source line at EEDID EEDID EEDID LCD panel, respectively. Voltage levels of all input signals are LVDS compatible (except VDD,EEDID). Refer to "Signal Electrical Characteristics for LVDS(*)", for voltage levels of all input signals. (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 10/27 Engineering Specification 5.3 Interface Signal Description The LVDS receiver equipped in this LCD module is compatible with ANSI/TIA/TIA-644 standard. PIN # SIGNAL NAME Description 2 GND Ground 3 VDD +3.3V Power Supply 4 VDD +3.3V Power Supply 5 V EEDID 3.3V Power Supply EEDID 6 Reserved Reserved 7 CLK EEDID Clock EEDID 8 Data EEDID Data EEDID 9 ReIN0- Negative LVDS differential data input (ER0-ER5, EG0) 10 ReIN0+ Positive LVDS differential data input (ER0-ER5, EG0) 11 GND Ground 12 ReIN1- Negative LVDS differential data input (EG1-EG5, EB0-EB1) 13 ReIN1+ Positive LVDS differential data input (EG1-EG5, EB0-EB1) 14 GND Ground 15 ReIN2- Negative LVDS differential data input (EB2-EB5, HSYNC, VSYNC, DSPTMG) 16 ReIN2+ Positive LVDS differential data input (EB2-EB5, HSYNC, VSYNC, DSPTMG) 17 GND Ground 18 ReCLKIN- Negative LVDS differential clock input (ECLK) 19 ReCLKIN+ Positive LVDS differential clock input (ECLK) 20 GND Ground 21 RoIN0- Negative LVDS differential data input (OR0-OR5, OG0) 22 RoIN0+ Positive LVDS differential data input (OR0-OR5, OG0) 23 GND Ground 24 RoIN1- Negative LVDS differential data input (OG1-OG5, OB0-OB1) 25 RoIN1+ Positive LVDS differential data input (OG1-OG5, OB0-OB1) 26 GND Ground 27 RoIN2- Negative LVDS differential data input (OB2-OB5) 28 RoIN2+ Positive LVDS differential data input (OB2-OB5) 29 GND Ground 30 RoCLKIN- Negative LVDS differential clock input (OCLK) 31 RoCLKIN+ Positive LVDS differential clock input (OCLK) Note: Input signals of odd and even clock shall be the same timing. The module uses a 100ohm resistor between positive and negative data lines of each receiver input. Even : First Pixel data Odd : Second Pixel Data (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 11/27 Engineering Specification SIGNAL NAME Description ER5/OR5 (Even / Odd) RED Data 5 ER4/OR4 (Even / Odd) RED Data 4 ER3/OR3 (Even / Odd) RED Data 3 ER2/OR2 (Even / Odd) RED Data 2 ER1/OR1 (Even / Odd) RED Data 1 ER0/OR0 (Even / Odd) RED Data 0 Red-pixel Data: Each red pixel's brightness data consists of these 6 bits pixel data. EG5/OG5 (Even / Odd) GREEN Data 5 EG4/OG4 (Even / Odd) GREEN Data 4 EG3/OG3 (Even / Odd) GREEN Data 3 EG2/OG2 (Even / Odd) GREEN Data 2 EG1/OG1 (Even / Odd) GREEN Data 1 EG0/OG0 (Even / Odd) GREEN Data 0 Green-pixel Data: Each green pixel's brightness data consists of these 6 bits pixel data. EB5/OB5 (Even / Odd) BLUE Data 5 EB4/OB4 (Even / Odd) BLUE Data 4 EB3/OB3 (Even / Odd) BLUE Data 3 EB2/OB2 (Even / Odd) BLUE Data 2 EB1/OB1 (Even / Odd) BLUE Data 1 EB0/OB0 (Even / Odd) BLUE Data 0 Blue-pixel Data: Each blue pixel's brightness data consists of these 6 bits pixel data. ECLK / OCLK Data Clock (DTCLK): The typical frequency is 81MHz. The signal is used to strobe the pixel +data and the +DSPTMG DSPTMG Display Timing: When the signal is high, the pixel data shall be valid to be displayed. VSYNC Vertical Sync: Both active high/low signals are acceptable. HSYNC Horizontal Sync: Both active high/low signals are acceptable. VDD Power Supply GND Ground V EEDID Power Supply EEDID CLK EEDID Clock EEDID Data EEDID Data EEDID Note: Output signals except V , CLK and Data from any system shall be Hi-Z state when VDD is off. EEDID EEDID EEDID (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 12/27 Engineering Specification 5.4 Interface Signal Electrical Characteristics 5.4.1 Signal Electrical Characteristics for LVDS Receiver Table. Electrical Characteristics Parameter Symbol Min Typ Max Unit Conditions Differential Input High Threshold Vth +100 mV Vcm=+1.2V Differential Input Low Threshold Vtl -100 mV Vcm=+1.2V Magnitude Differential Input Voltage |Vid| 100 600 mV Common Mode Voltage Vcm 1.0 1.2 1.4 V Vth - Vtl = 200mV Common Mode Voltage Offset ∆Vcm -50 +50 mV Vth - Vtl = 200mV Note: ▪ Input signals shall be low or Hi-Z state when VDD is off. ▪ All electrical characteristics for LVDS signal are defined and shall be measured at the interface connector of LCD (see Figure Measurement system). Figure . Voltage Definitions (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 13/27 Engineering Specification Figure. Measurement system Table. Switching Characteristics Parameter Symbol Min Typ Max Unit Conditions Clock Frequency fc 53.0 81.0 83.0 MHz Cycle Time tc 12.0 12.3 18.8 ns fc = 81MHz, tCCJ < 50ps, Data Setup Time (Note 1) Tsu 500 ps Vth-Vtl = 200mV, Thd 500 ps Data Hold Time (Note 2) Vcm = 1.2V, ∆Vcm = 0 Cycle-to-cycle jitter (Note 3) tCCJ -150 +150 ps fc = 81MHz Cycle Modulation Rate (Note 4) tCJavg 20 ps/clk fc = 81MHz Clock Skew between LVDS 1 ns ODD/EVEN channels Note 1: All values are at VDD=3.3V, Ta=25 degree C. Note 2: See figure "Timing Definition" and "Timing Definition (detail A)" for definition. Note 3: Jitter is the magnitude of the change in input clock period. Note 4: This specification defines maximum average cycle modulation rate in peak-to-peak transition within any 100 clock cycles. This specification is applied only if input clock peak jitter within any 100 clock cycles is greater than 300ps. (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 14/27 Engineering Specification Figure. Timing Definition (Even) (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 15/27 Engineering Specification Figure. Timing Definition (Odd) (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 16/27 Engineering Specification Figure. Timing Definition (detail A) Note: Tsu and Thd are internal data sampling window of receiver. Trskm is the system skew margin; i.e., the sum of cable skew, source clock jitter, and other inter-symbol interference, shall be less than Trskm. (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 17/27 Engineering Specification 5.4.2 LVDS Receiver Internal Circuit Below figure shows the internal block diagram of the LVDS receiver. (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 18/27 Engineering Specification 5.4.3 Recommended Guidelines for Motherboard PCB Design and Cable Selection Following the suggestions below will help to achieve optimal results. ▪ Use controlled impedance media for LVDS signals. They should have a matched differential impedance of 100ohm. ▪ Match electrical lengths between traces to minimize signal skew. ▪ Isolate TTL signals from LVDS signals. ▪ For cables, twisted pair, twinax, or flex circuit with close coupled differential traces are recommended. 5.5 Signal for Lamp Connector Pin # Signal Name 1 Lamp High Voltage 2 Lamp Low Voltage (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 19/27 Engineering Specification 6.0 Pixel format image Following figure shows the relationship of the input signals and LCD pixel format image. Even and odd pair of RGB data are sampled at a time. Even Odd Even Odd 0 1 1598 1599 1st Line R G B R G B R G B R G B R G B R G B R G B R G B 1200th Line (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 20/27 Engineering Specification 7.0 Parameter guide line for CFL Inverter PARAMETER MIN DP-1 MAX UNITS CONDITION 2 White Luminance - 200 - cd/m (Ta=25 deg.C) Note 6 CFL current (ICFL) TBD 6.5 7.0 mArms (Ta=25 deg.C) Note 5 CFL Frequency (FCFL) 40 - 70 KHz (Ta=25 deg.C) Note 1 CFL Ignition Voltage (Vs) 1,600 - - Vrms (Ta= 0 deg.C) Note 3 CFL Voltage (Reference)(VCFL) - 630 - Vrms (Ta=25 deg.C) Note 2 CFL Power consumption (PCFL) - 4.1 4.5 W (Ta=25 deg.C) Note 2 Note 1: CFL discharge frequency should be carefully determined to avoid interference between inverter and TFT LCD. Note 2: Calculated value for reference (ICFL x VCFL = PCFL). Note 3: CFL inverter should be able to give out a power that has a generating capacity of over 1,600 voltage. Lamp units need 1,600 voltage minimum for ignition. Note 4: DP-1 (Design Point-1) is IDTech recommended Design Point. *1 All of characteristics listed are measured under the condition using the IDTech Test inverter. *2 In case of using an inverter other than listed, it is recommended to check the inverter carefully. Sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 In designing an inverter, it is suggested to check safety circuit very carefully. Impedance of CFL, for instance, becomes more than 1 [M ohm] when CFL is damaged. *4 Generally, CFL has some amount of delay time after applying kick-off voltage. It is recommended to keep on applying kick-off voltage for 1 [Sec] until discharge. *5 Reducing CFL current increases CFL discharge voltage and generally increases CFL discharge frequency. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. *6 It should be employed the inverter which has 'Duty Dimming', if ICFL is less than 4[mA]. Note 5: To use inverter card of SANKEN SCF-0281. Note 6: 200 Typ. (center), 170 Min. (center), 185 Typ. (5 point average) (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 21/27 Engineering Specification The following chart is Luminance versus Lamp Power for your reference. (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 22/27 Engineering Specification 8.0 Interface Timings Basically, interface timings described here is not actual input timing of LCD module but output timing of SN75LVDS86 (Texas Instruments) or equivalent. 8.1 Timing Characteristics Signal Item Symbol MIN. TYP. MAX. Unit DTCLK Freqency Fdck 53.0 81.0 83.0 [MHz] (ECLK/OCLK) Tck 12.0 12.3 18.8 [ns] +V-Sync Frame Rate Fv - 60.0 - [Hz] Tv - 16.67 - [ms] Nv 1208 1250 2046 [lines] T V-Active Level va 13.33 40.0 839.8 [us] Nva 1 3 63 [lines] V-Back Porch Nvb 6 46 125 [lines] V-Front Porch Nvf 1 1 125 [lines] +DSPTMG V-Line m 1200 [lines] +H-Sync Scan Rate Fh - 75.0 - [KHz] Th - 13.33 - [usec] Nh 1024 1080 2046 [Tck] T H-Active Level ha 1.185 [usec] Tha 8 96 255 [Tck] H-Back Porch Thb 8 152 511 [Tck] H-Front Porch Thf 8 32 [Tck] +DSPTMG Display Thd - 9.877 - [usec] +DATA Data Even/Odd n 1600 [dots] Note: Both positive Hsync and positive Vsync polarity is recommended. Disp Timing Period (Th, Nh) must be constant by each every line. If Disp timing are not constant due to Spread Spectrum, the following expression has to be satisfied. DeltaDT x Tvblk < 300 [Tck] DTmax : Disp Timing Period MAX [Tck] DTmin : Disp Timing Period MIN [Tck] DeltaDT = DTmax - DTmin Tvblk : V Blanking [lines] Tck : DTCLK (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 23/27 Engineering Specification 8.2 Timing Definition Vertical Timing Support mode Tvblk m Tvf VSYNC Tv,Nv Tva VSYNC Tvb VSYNC Vertical Active Field Front Porch Frame Time Width Back Porch Blanking 1600 x 1200 at 60Hz 0.667 ms 16.000 ms 0.013 ms 16.667 ms 0.040 ms 0.613 ms (H line rate : 13.3 us) (50 lines) (1200 lines) (1 line) (1250 lines) (3 lines) (46 lines) DSPTMG Tv Tvblk m Tvf Tva Tvb +VSYNC Horizontal Timing Support mode Thblk Thd Thf HSYNC Th,Nh Tha Thb Horizontal Active Field Front Porch H Line Time HSYNC HSYNC Blanking Width Back Porch 1600 x 1200 3.457 us 9.877 us 0.395 us 13.333 us 1.185 us 1.877 us Dotclock : 162.000 (560 dots) (1600 dots) (64 dots) (2160 dots) (192 dots) (304 dots) MHz (81.000MHz x2) DSPTMG Th Thblk Thd Thf Tha Thb -HSYNC +HSYNC Tck VID VIDE EO O( (Eve Even n) ) 02 4 n-4 n-2 V VIID DE EO( O(Od Odd d)) 13 5 n-3 n-1 DTCLK (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 24/27 Engineering Specification 9.0 Power Specifications Input power specifications are as follows; Operating Input Voltage Conditions: +3.0V to +3.6V Power Characteristics SYMBOL PARAMETER Min Typ Max UNITS CONDITION VDD Logic/LCD Drive Voltage 3.0 3.3 3.6 [V] Load Capacitance 68 uF PDD VDD Power 4.4 [W] MAX.Pattern, VDD=3.6[V] PDD VDD Power 3.1 [W] All White Pattern, VDD=3.3[V] IDD VDD Current 1.44 [A] MAX.Pattern, VDD=3.0[V] IDD VDD Current 0.95 [A] All White Pattern, VDD=3.3[V] VDDrp Allowable Logic/LCD 100 [mVp-p] Drive Ripple Voltage VDDns Allowable Logic/LCD 100 [mVp-p] Drive Ripple Noise Note: VDD Line impedance of between system side and LCD panel should be minimized for meeting the above requirements. (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 25/27 Engineering Specification 10.0 Power ON/OFF Sequence VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off. 150ms min. 90% 90% VDD 10% 10% 10% 0 V 10ms max. 0 min. 0 min. 90% 90% Signals 10% 10% 0 V 100ms min. 20ms min. 180ms min. (Recommended). On Lamp (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 26/27 Engineering Specification 11.0 Mechanical Characteristics 12.0 National Test Lab Requirement The display module will satisfy all requirements for compliance to UL 60950, 3rd Edition U.S.A. Information Technology Equipment CAN/CSA-C22.2 No.60950-00 Canada, Information Technology Equipment IEC 60950 (3rd. Ed.) International, Information Technology Equipment EN 60950 (3rd. Ed.) International, Information Processing Equipment (European Norm for IEC60950) Conditions of Acceptability For use only in or with complete equipment where the acceptability of the combination is determined by Underwriters laboratories Inc. When installed in an end-product, consideration must be given to the following: ▪ The terminals and connectors are suitable for factory wiring only. ▪ The component has been evaluated for use in a Pollution Degree 2 environment. ▪ Need for fire and/or electrical enclosures hall be considered in end product. ▪ The unit is intended to be supplied by SELV and Limited Power Source. Also separated from electrical parts, which may produce high temperature that could cause ignition by at least 13 mm of air or by a solid barrier of material of V-1 minimum due to materials having no flammability rating. ▪ Back light lamp is rated 630 V rms, 6.5 mA, and intended to be supplied by Limited Current Circuit. ▪ Insulation between Backlight circuit and other SELV circuit has not been evaluated. Additional consideration shall be made if backlight is supplied by a source other than limited current circuit. ****** End Of Page ****** (C) Copyright International Display Technology 2004 All Rights reserved February 18, 2004 OEM I-N150U3-L06 27/27