Elite.Parts chervon right Manufacturers chervon right I chervon right ICPDAS chervon right ISaGRAF Book-C
About product Datasheet FAQ

ICPDAS ISaGRAF Book-C

Description

ISaGRAF Application Book (Chinese)

Part Number

ISaGRAF Book-C

Price

Request Quote

Manufacturer

ICPDAS

Lead Time

Request Quote

Category

PRODUCTS - I

Datasheet

pdf file

IKIT-20.pdf

59 KiB

Extracted Text

Specifications: I-8437 / 8837 Power supply Power requirements 10 to 30VDC (unregulated) Power consumption 20W (when I/O slots are empty ) Protection Built-in power protection & network protection circuit General environment Operating temperature -25°C to +75°C Storage temperature -30°C to +85°C Humidity 0 to 95 % (non-condensed) System CPU Am188™ES,40MHz, or compatiable Watchdog timer 0.8 second Real time clock Year-2000 compliance. Gives hour, minute, sec, date of week, date of month, month & year (1980 to 2079) SRAM 512Kbytes FLASH Memory 512Kbytes, Erase unit is 64K bytes, 100,000 erase/write cycles NVSRAM 31 bytes, battery backup, data valid up to 10 years EEPROM 2048 bytes, retention > 100 years. 1,000,000 erase/write cycles SMMI Five 7-Seg. Led, four push buttons & three Led on the front panel. It can display message, value, input value, simulate input & ouput. I/O slots 4 empty slots for I-8437, 8 empty slots for I-8837 Accept parallel & serial I/O boards NET ID 8 dip switch to set NET ID as 1 to 255 Ethernet port 10M bps, NE2000 compatible, 10 BaseT, Program download port. Serial ports COM1 RS232: TXD,RXD,GND, Speed: 115200 bps max. Program download port. COM3 Can be configed as RS232 or S485, Speed: 115200 bps max. RS232: TXD,RXD,RTS,CTS,GND, RS485: Data+, Data- COM4 RS232: Full modem signals, Speed: 115200 bps max. TXD,RXD,RTS,CTS,DSR,DTR,CD,RI,GND. Development software ISaGRAF IEC61131-3 standard. Languages: LD, ST, FBD, SFC, IL & FC Motion control The I-8417/8817/8437/8837 can integrate with one I-8091(2-axes) or two I-8091(4-axes) motion board to do motion control. When doing motion control, Ethernet communication is not available. PWM output Pulse Width Modulation 8 channels max. for one controller. output 500Hz max. for Off=1 & On=1 ms Output square curve: Off: 1 to 32767 ms, On: 1 to 32767 ms Optional parallel D/O boards: i-8037, 8041, 8042, 8054, 8055, 8056, 8057, 8060, 8063, 8064, 8065, 8066,8068, 8069 Specifications Of ISaGRAF Embedded Controller 1 ICP DAS Counters Parallel D/I counter 8 ch. max. for one controller. Counter value: 32 bit 500Hz max. Min. pulse width > 1ms Optional parallel D/I boards: i-8040, 8042, 8051, 8052, 8053, 8054, 8055, 8058, 8063, 8077 Serial D/I counter Counter input: 100Hz max. Counter value: 0 to 65535 (16 bit) Optional serial I-87K D/I boards: i-87051, 87052, 87053, 87054, 87055, 87058, 87063 Remote D/I counter All remote I-7000 & I-87K D/I modules support counters. 100Hz max. Counter value: 0 to 65535 (16 bit) High speed counter i-87082: 100kHz max. 32 bit, i-8080: 5kHz max. 32 bit Protocols Modbus serial protocol COM1 supports Modbus serial protocol for connecting PC/HMI & MMI panels. Modbus TCP/IP protocol Ethernet port supports Modbus TCP/IP protocol for connecting PC/HMI. Remote I/O COM3 & COM4 supports I-7000 I/O modules & (I-87K base + I- 87K serial I/O boards) as remote I/O. Max. 64 I/O module for one controller Modbus slave I/O devices COM3 & COM4 supports Modbus master protocol to connect to other Modbus slave I/O devices Fbus A software mechanism built in COM3 port to exchange data between ICP DAS’s ISaGRAF controllers. Ebus A software mechanism built in Ethernet port to exchange data between ICP DAS’s ISaGRAF Ethernet controllers. SMS: COM4 can link to a GSM modem to support SMS. User can Short Message Service request data or control the controller by cellular phone. The controller can also send data & alarms to user’s cell. phone. Optional GSM modems: M1203A: GSM 900/1800 MHz M1213A: GSM 900/1900 MHz User defined protocol User can write his own protocol applied at COM3, COM4 (& COM5 to COM20 if multi-serial port boards are plugged). Modem_Link Supports PC remotely download & monitor I- 8417/8817/8437/8837 through a normal modem. MMICON / LCD COM3 & COM4 supports ICP DAS’s MMICON. The MMICON is featured with a 240 x 64 dot LCD and a 4 x 4 Keyboard. User can use it to display picture, string, integer, float, and input a character, string, integer and float. Redundant Bus7000 Two ISaGRAF controllers can link to remote I-7000 & I-87K I/O modules at the same time. Only one controller is active to control these remote I/Os. If one is dead, the other one will take over the control of remote I/Os. Battery backup SRAM Data, date & time can be stored at S256/S512, and then PC can load these data via COM1 or COM2. PC can also download pre-defined data to the S256/S512. Optional: S256: 256kbytes, S512: 512kbytes PID Software provides PID function Specifications Of ISaGRAF Embedded Controller 2 ICP DAS Specifications: I-8417 / 8817 Power supply Power requirements 10 to 30VDC (unregulated) Power consumption 20W (when I/O slots are empty ) Protection Built-in power protection & network protection circuit General environment Operating temperature -25°C to +75°C Storage temperature -30°C to +85°C Humidity 0 to 95 % (non-condensed) System CPU Am188™ES,40MHz, or compatiable Watchdog timer 0.8 second Real time clock Year-2000 compliance. Gives hour, minute, sec, date of week, date of month, month & year (1980 to 2079) SRAM 512Kbytes FLASH Memory 512Kbytes, Erase unit is 64K bytes, 100,000 erase/write cycles NVSRAM 31 bytes, battery backup, data valid up to 10 years EEPROM 2048 bytes, retention > 100 years. 1,000,000 erase/write cycles SMMI Five 7-Seg. Led, four push buttons & three Led on the front panel. It can display message, value, input value, simulate input & ouput. I/O slots 4 empty slots for I-8417, 8 empty slots for I-8817 Accept parallel & serial I/O boards NET ID 8 dip switch to set NET ID as 1 to 255 Serial ports COM1 RS232: TXD,RXD,GND, Speed: 115200 bps max. Program download port. COM2 RS485: Data+, Data-, Speed: 115200 bps max. Self-tuner ASIC inside, Program download port. COM3 Can be configed as RS232 or S485, Speed: 115200 bps max. RS232: TXD,RXD,RTS,CTS,GND, RS485: Data+, Data- COM4 RS232: Full modem signals, Speed: 115200 bps max. TXD,RXD,RTS,CTS,DSR,DTR,CD,RI,GND. Development software ISaGRAF IEC61131-3 standard. Languages: LD, ST, FBD, SFC, IL & FC Motion control The I-8417/8817/8437/8837 can integrate with one I-8091(2-axes) or two I-8091(4-axes) motion board to do motion control. When doing motion control, Ethernet communication is not available. PWM output Pulse Width Modulation 8 channels max. for one controller. output 500Hz max. for Off=1 & On=1 ms Output square curve: Off: 1 to 32767 ms, On: 1 to 32767 ms Optional parallel D/O boards: i-8037, 8041, 8042, 8054, 8055, 8056, 8057, 8060, 8063, 8064, 8065, 8066,8068, 8069 Specifications Of ISaGRAF Embedded Controller 3 ICP DAS Counters Parallel D/I counter 8 ch. max. for one controller. Counter value: 32 bit 500Hz max. Min. pulse width > 1ms Optional parallel D/I boards: i-8040, 8042, 8051, 8052, 8053, 8054, 8055, 8058, 8063, 8077 Serial D/I counter Counter input: 100Hz max. Counter value: 0 to 65535 (16 bit) Optional serial I-87K D/I boards: i-87051, 87052, 87053, 87054, 87055, 87058, 87063 Remote D/I counter All remote I-7000 & I-87K D/I modules support counters. 100Hz max. Counter value: 0 to 65535 (16 bit) High speed counter i-87082: 100kHz max. 32 bit, i-8080: 5kHz max. 32 bit Protocols Modbus serial protocol COM1 & COM2 supports Modbus serial protocol for connecting PC/HMI & MMI panels. Remote I/O COM3 & COM4 supports I-7000 I/O modules & (I-87K base + I- 87K serial I/O boards) as remote I/O. Max. 64 I/O module for one controller Modbus slave I/O devices COM3 & COM4 supports Modbus master protocol to connect to other Modbus slave I/O devices Fbus A software mechanism built in COM3 port to exchange data between ICP DAS’s ISaGRAF controllers. SMS: Short MessageCOM4 can link to a GSM modem to support SMS. User can Service request data or control the controller by cellular phone. The controller can also send data & alarms to user’s cell. phone. Optional GSM modems: M1203A: GSM 900/1800 MHz M1213A: GSM 900/1900 MHz User defined protocol User can write his own protocol applied at COM3, COM4 (& COM5 to COM20 if multi-serial port boards are plugged). Modem_Link Supports PC remotely download & monitor I- 8417/8817/8437/8837 through a normal modem. MMICON / LCD COM3 & COM4 supports ICP DAS’s MMICON. The MMICON is featured with a 240 x 64 dot LCD and a 4 x 4 Keyboard. User can use it to display picture, string, integer, float, and input a character, string, integer and float. Redundant Bus7000 Two ISaGRAF controllers can link to remote I-7000 & I-87K I/O modules at the same time. Only one controller is active to control these remote I/Os. If one is dead, the other one will take over the control of remote I/Os. Battery backup SRAM Data, date & time can be stored at S256/S512, and then PC can load these data via COM1 or COM2. PC can also download pre-defined data to the S256/S512. Optional: S256: 256kbytes, S512: 512kbytes PID Software provides PID function Specifications Of ISaGRAF Embedded Controller 4 ICP DAS Specifications: I-7188EG Power supply Power requirements 10 to 30VDC (unregulated) Power consumption 7188EG:2W , 7188EGD: 3W Protection Built-in power protection & network protection circuit General environment Operating temperature -25°C to +75°C Storage temperature -40°C to +85°C Humidity 0 to 95 % (non-condensed) System CPU Am188™ES,40MHz, or compatiable Watchdog timer 1.6 second Real time clock Year-2000 compliance. Gives hour, minute, sec, date of week, date of month, month & year (1980 to 2079) SRAM 512Kbytes FLASH Memory 512Kbytes, Erase unit is 64K bytes, 100,000 erase/write cycles NVSRAM 31 bytes, battery backup, data valid up to 10 years EEPROM 2048 bytes, retention > 100 years. 1,000,000 erase/write cycles Display for I-7188EGD Five 7-Seg. Led on the front. It can display message & value. Expansion I/O bus One optional Xxxx series I/O board can be plugged inside I- 7188EG/D. NET ID Set by software Ethernet port 10M bps, NE2000 compatible, 10 BaseT, Program download port. Serial ports COM1 RS232: TXD,RXD,RTS,CTS,GND, Speed: 115200 bps max. Program download port. COM2 RS485: D+, D- , Speed: 115200 bps max. Self-tuner ASIC inside Development software ISaGRAF Supports IEC61131-3 standard. Programming languages: LD, ST, FBD, SFC, IL & FC PWM output Pulse Width Modulation All Xxxx series D/O boards support PWM output. output 8 channels max. for one controller. 500Hz max. for Off=1 & On=1 ms Output square curve: Off: 1 to 32767 ms, On: 1 to 32767 ms Specifications Of ISaGRAF Embedded Controller 5 ICP DAS Counters Parallel D/I counter All Xxxx series D/I boards support D/I counter. 8 ch. max. for one controller. Counter value: 32 bit 500Hz max. Min. pulse width > 1ms Remote D/I counter All remote I-7000 & I-87K D/I modules support counters. 100Hz max. Counter value: 0 to 65535 (16 bit) Remote high speed Optional i-87082:100kHz max. , 32 bit counter Protocols Modbus serial protocol COM1 supports Modbus serial protocol for connecting PC/HMI & MMI panels. Modbus TCP/IP protocol Ethernet port supports Modbus TCP/IP protocol for connecting PC/HMI. Remote I/O COM2 (or COM3:RS485 if found) supports I-7000 I/O modules & (I-87K base + I-87K serial I/O boards) as remote I/O.Max. 64 I/O modules for one controller Modbus slave I/O devices COM2 (or COM3 if found) supports Modbus master protocol to connect to other Modbus slave I/O devices Fbus A software mechanism built in COM2 port to exchange data between ICP DAS’s IsaGRAF controllers. Ebus A software mechanism built in Ethernet port to exchange data between ICP DAS’s ISaGRAF Ethernet controllers. SMS: Short Message(COM3:RS232 or COM4:RS232 if found) can link to a GSM Service modem to support SMS. User can request data or control the controller by cellular phone. The controller can also send data & alarms to user’s cell. phone. Optional GSM modems: M1203A: GSM 900/1800 MHz , M1213A: GSM 900/1900 MHz User defined protocol User can write his own protocol applied at COM2 & (COM3 to COM8 if found). MMICON / LCD (COM3:RS232 if found) supports ICP DAS’s MMICON. The MMICON is featured with a 240 x 64 dot LCD and a 4 x 4 Keyboard. User can use it to display picture, string, integer, float, and input a character, string, integer and float. Redundant Bus7000 Two ISaGRAF controllers can link to remote I-7000 & I-87K I/O modules at the same time. Only one controller is active to control these remote I/Os. If one is dead, the other one will take over the control of remote I/Os. Battery backup SRAM Data, date & time can be stored at X607/X608, and then PC can load these data via COM1. PC can also download pre-defined data to the X607/X608. Optional: X607:128kbytes , X608:512kbytes PID Software provides PID function Specifications Of ISaGRAF Embedded Controller 6 ICP DAS Specifications: I-7188XG Power supply Power requirements 10 to 30VDC (unregulated) Power consumption 7188XG:2W , 7188XGD: 3W Protection Built-in power protection & network protection circuit General environment Operating temperature -25°C to +75°C Storage temperature -40°C to +85°C Humidity 0 to 95 % (non-condensed) System CPU Am188™ES,40MHz, or compatiable Watchdog timer 1.6 second Real time clock Year-2000 compliance. Gives hour, minute, sec, date of week, date of month, month & year (1980 to 2079) SRAM 512Kbytes FLASH Memory 512Kbytes, Erase unit is 64K bytes, 100,000 erase/write cycles NVSRAM 31 bytes, battery backup, data valid up to 10 years EEPROM 2048 bytes, retention > 100 years. 1,000,000 erase/write cycles Display for I-7188XGD Five 7-Seg. Led on the front. It can display message & value. Expansion I/O bus One optional Xxxx series I/O board can be plugged inside I- 7188XG/D. NET ID Set by software Serial ports COM1 Can be used as RS232 or RS485 , Speed: 115200 bps max. RS232 TXD,RXD,RTS,CTS,GND RS485: D+, D-, self-tuner inside Program download port. COM2 RS485: D+, D- , Self-tuner ASIC inside , Speed: 115200 bps max. Development software ISaGRAF Supports IEC61131-3 standard. Programming languages: LD, ST, FBD, SFC, IL & FC PWM output Pulse Width Modulation All Xxxx series D/O boards support PWM output. output 8 channels max. for one controller. 500Hz max. for Off=1 & On=1ms Output square curve: Off: 1 to 32767 ms, On: 1 to 32767 ms Specifications Of ISaGRAF Embedded Controller 7 ICP DAS Counters Parallel D/I counter All Xxxx series D/I boards support D/I counter. 8 ch. max. for one controller. Counter value: 32 bit, 500Hz max. Min. pulse width > 1ms Remote D/I counter All remote I-7000 & I-87K D/I modules support counters. 100Hz max. , Counter value: 0 to 65535 (16 bit) Remote high speed Optional i-87082:100kHz max. 32 bit counter Protocols Modbus serial protocol COM1 supports Modbus serial protocol for connecting PC/HMI & MMI panels. Remote I/O COM2 (or COM3:RS485 if found) supports I-7000 I/O modules & (I-87K base + I-87K serial I/O boards) as remote I/O.Max. 64 I/O modules for one controller Modbus slave I/O devices COM2 (or COM3 if found) supports Modbus master protocol to connect to other Modbus slave I/O devices Fbus A software mechanism built in COM2 port to exchange data between ICP DAS’s IsaGRAF controllers. SMS: Short Message(COM3:RS232 or COM4:RS232 if found) can link to a GSM Service modem to support SMS. User can request data or control the controller by cellular phone. The controller can also send data & alarms to user’s cell. phone. Optional GSM modems: M1203A: GSM 900/1800 MHz M1213A: GSM 900/1900 MHz User defined protocol User can write his own protocol applied at COM2 & (COM3 to COM8 if found). MMICON / LCD (COM3:RS232 if found) supports ICP DAS’s MMICON. The MMICON is featured with a 240 x 64 dot LCD and a 4 x 4 Keyboard. User can use it to display picture, string, integer, float, and input a character, string, integer and float. Redundant Bus7000 Two ISaGRAF controllers can link to remote I-7000 & I-87K I/O modules at the same time. Only one controller is active to control these remote I/Os. If one is dead, the other one will take over the control of remote I/Os. Battery backup SRAM Data, date & time can be stored at X607/X608, and then PC can load these data via COM1. PC can also download pre-defined data to the X607/X608. Optional: X607:128kbytes , X608:512kbytes PID Software provides PID function Specifications Of ISaGRAF Embedded Controller 8 ICP DAS Selection Guide Power supply ACE-540A 24V/1.7A power supply(panel Mount) DIN-540A 24V/1.7A power supply(DIN-Rail mount) KA-52F 24V/1A power supply(no mounting) DIN-KA52F 24V/1A power supply(DIN-Rail mountong) KWM020-1824F 24V/0.75A power supply (No-mounting) Development tools ISaGRAF-256 ISaGRAF Workbench Software, up to 256 I/O tags. ISaGRAF Book-E User’s manual of ISaGRAF controllers (English) ISaGRAF Book-C User’s manual of ISaGRAF controllers (Chinese, traditional) ISaGRAF controller I-8417 ISaGRAF I-8000 controller, 4 empty slots I-8817 ISaGRAF I-8000 controller, 8 empty slots I-8437 ISaGRAF I-8000 ethernet controller, 4 empty slots I-8837 ISaGRAF I-8000 ethernet controller, 8 empty slots I-7188XG ISaGRAF I-7188 controller I-7188XGD ISaGRAF I-7188 controller with display I-7188EG ISaGRAF I-7188 ethernet controller I-7188EGD ISaGRAF I-7188 ethernet controller with display IVIEW-100-ISaGRAF ISaGRAF IVIEW-100 controller Battery backup SRAM S256 256Kbytes battery backup SRAM for I-8417 /8817/8437/8837 & IVIEW-100-ISaGRAF S512 512Kbytes battery backup SRAM for I-8417 /8817/8437/8837 & IVIEW-100-ISaGRAF X607 128Kbytes battery backup SRAM for I-7188XG/7188EG X608 512Kbytes battery backup SRAM for I-7188XG/7188EG MMICON / LCD MMICON + 240x64 Graphic LCD GSM modem M1203A 900/1800 GSM/GPRS External Modem M1213A 900/1900 GSM/GPRS External Modem I-87K expansion base I-87K4 Remote I-87K I/O base, 4 empty slots I-87K5 Remote I-87K I/O base, 5 empty slots I-87K8 Remote I-87K I/O base, 8 empty slots I-87K9 Remote I-87K I/O base, 9 empty slots Motion control board I-8091 2-axes stepping/servo motor control card I-8090 3-axes encoder card Specifications Of ISaGRAF Embedded Controller 9 ICP DAS Timer/Counter board I-8080 4-ch. counter/frequency, 32 bit I-87082 2 channel counter/Frequency, 32 bit Multi-serial board I-8112 2 port RS232 I-8114 4 port RS232 I-8142 2 port RS485/422 I-8144 4 port RS485/422 Parallel analog I/O board I-8017H 8-ch. 14-bit analog input, each ch. can be different input type (V, mA) & range I-8024 4-ch. 14-bit analog output, each ch. can be different output type (V,mA) & range Parallel digital I/O board I-8037 16-ch. isolated open-drain output I-8040 32-ch. isolated digital input I-8041 32-ch. isolated digital output I-8042 Isolated digital 16-ch. input & 16-ch. output I-8051 16-ch. non-isolated digital input I-8052 8-ch. isolated digital input (differential) I-8053 16-ch. isolated digital input (single ended) I-8054 Isolated digital 8-ch. input & 8-ch. output I-8055 Non-isolated digital 8ch. input & 8ch. output I-8056 16-ch. non-isolated O.C. output I-8057 16-ch. isolated O.C. output I-8058 8-ch. isolated digital input, AC/DC I-8060 6-ch. relay output I-8063 Isloated digital 4-ch. input & 4-ch. relay I-8064 8-ch. power relay output I-8065 8-ch. SSR-AC output I-8066 8-ch. SSR-DC output I-8068 8-ch. relay output I-8069 8-ch. Photo Mos relay output I-8077 8-ch. digital input & 8-ch. output simulator Serial analog I/O board I-87013 4-ch. RTD input I-87017 8-ch. analog input I-87018 8-ch. thermocouple input I-87022 2-ch. 12-bit analog output, each ch. can be different output type (V,mA) & range I-87024 4-ch. 14-bit analog output I-87026 2-ch. 16-bit analog output, each ch. can be different output type (V,mA) & range Specifications Of ISaGRAF Embedded Controller 10 ICP DAS Serial digital I/O board I-87051 16-ch. non-isolated digital input I-87052 8-ch. isolated digital input (differential) I-87053 16-ch. isolated digital input (single ended) I-87054 Isolated digital 8-ch. input & 8-ch. output I-87055 Non-isolated digital 8ch. input & 8ch. output I-87057 16-ch. isolated O.C. output I-87058 8-ch. isolated digital input, AC/DC I-87063 Isloated digital 4-ch. input & 4-ch. relay I-87064 8-ch. power relay output I-87065 8-ch. SSR-AC output I-87066 8-ch. SSR-DC output I-87068 8-ch. relay output Conveter & Repeater PCISA-7520R PCI/ISA bus RS-232 to RS-485/422 card PCISA-7520AR RS-232 to RS-422/RS-485 card with D-sub 9-pin cable I-7520 RS-232 to RS-485 converter I-7520R I-7520 with 3000V DC isolation at RS-485 side I-7520A RS-232 to RS-422/RS-485 converter I-7520AR I-7520A with 3000V DC isolation at RS-485 side I-7061 USB to RS-232/422/485 Converter I-7510 RS-485 isolated high speed repeater I-7510R RS485/RS422 isolated high speed repeater I-7510AR Three way Isolated RS-422/485 Repeater RS485 Hub 3-way isolated RS485 to 3 ports RS485 hub Man Machine Interface Touch506S 5.7" Color STN Panel display with touch Touch510S 10.4" Color STN Panel Display With Touch Touch510T 10.4" Color TFT Panel Display With Touch I-7000 analog I/O module I-7011 1-ch. thermo-couple input (16-bit), 1-ch. D/I & 2-ch. D/O I-7011D I-7011 with display I-7011P 1-ch. thermo-couple input (16-bit), 1-ch. D/I & 2-ch. D/O I-7011PD I-7011P with display I-7012 1-ch. analog input (16-bit), 1-ch. D/I & 2-ch. D/O I-7012D I-7012D with display I-7012F Fast mode I-7012 (12-bit), normal 16-bit I-7012FD I-7012F with display I-7013 1-ch. RTD input (16-bit) I-7013D I-7013 with display I-7033 3-ch. RTD input (16-bit) I-7033D I-7033 with display I-7014D 1-ch. analog/transmitter input (16-bit) with display, 1-ch. D/I & 2- ch. D/O I-7016 1-ch. strained gauge input (16-bit), 1-ch. D/I & 4-ch. D/O Specifications Of ISaGRAF Embedded Controller 11 ICP DAS I-7016D I-7016 with display I-7016P 1-ch. strained gauge input (16-bit), 1-ch. D/I & 4-ch. D/O I-7016PD I-7016 with display I-7017 8-ch. analog input (16-bit) I-7017F Fast mode I-7017 (12-bit), normal (16-bit) I-7018 8-ch. thermocouple input (16-bit) I-7018P 8-ch. thermocouple input (16-bit) I-7021 1-ch. analog output (12-bit) I-7021P 1-ch. analog output (16-bit) I-7022 2-ch. analog output (12-bit), each ch. can be different output type (V,mA) & range I-7024 4-ch. analog output (14-bit) I-7000 digital I/O module I-7041 14-ch. isolated digital input I-7041D I-7041 with LED display I-7042 13-ch. isolated O.C. output I-7042D I-7042 with LED display I-7043 16-ch. non-isolated O.C. output I-7043D I-7043 with LED display I-7044 Isolated digital 4-ch. input & 8-ch. output I-7044D I-7044 with LED display I-7050 7-ch. digital input & 8-ch. output I-7050D I-7050 with LED display I-7050A 7 digital input & 8 output (current source) I-7050AD I-7050A with LED display I-7052 8-ch. isolated digital input (6 differential + 2 single end) I-7052D I-7052 with LED display I-7053 16-ch. digital input I-7053D I-7053 with LED display I-7060 4-ch. isolated input & 4-ch. relay output I-7060D I-7060 with LED display I-7063 8-ch. isolated input & 3ch. power relay I-7063D I-7063D with LED display I-7063A 8-ch. isolated input & 3ch. AC-SSR output I-7063AD I-7063A with LED display I-7063B 8-ch. isolated input & 3ch. DC-SSR output I-7063BD I-7063B with LED display I-7065 4-ch. isolated input & 5ch. power relay I-7065D I-7065 with LED display I-7065A 4-ch. isolated input & 5ch. AC-SSR relay I-7065AD I-7065A with LED display I-7065B 4-ch. isolated input & 5ch. DC-SSR relay I-7065BD I-7065B with LED display I-7066 7-ch. Photo Mos relay output I-7066D I-7066 with LED display I-7067 7-ch. relay output I-7067D I-7067 with LED display Specifications Of ISaGRAF Embedded Controller 12 ICP DAS I-7000 counter module I-7080 2 high speed counter/frequency input I-7080D I-7080 with display Parallel I/O board For I-7188XG & I-7188EG X107 6-ch. D/I and 7-ch. D/O X109 7-ch. PhotoMos Relay X110 14-ch. D/I X111 13-ch. D/O X119 7-ch. D/O and 7-ch. D/I X202 7-ch. A/D (0~20mA) X203 2-ch. A/D (0~20mA), 2-ch. D/I, 6-ch. D/O X303 1-ch. A/D (+/-5V), 1-ch. D/A (+/-5V), 4-ch. D/I, 6-ch. D/O X304 3-ch. A/D (+/-5V), 1-ch. D/A (+/-5V), 4-ch. D/I, 4-ch. D/O X305 7-ch. A/D (+/-5V), 1-ch. D/A (+/-5V), 2-ch. D/I, 2-ch. D/O X307 8-ch. A/D (+/-10V), 2-ch. D/I, 2-ch. D/O (will be available) X308 4-ch. A/D (+/-10V), 6-ch. D/O (will be available) X310 1-ch. A/D (0~10V), 1-ch. A/D (0~20mA), 2-ch. D/A (0~10V), 3-ch. D/I, 3-ch. D/O RS232/422/485 board For I-7188XG & I-7188EG X503 1-Port RS-232 (5-Pin) X504 2-Port RS-232 (5-Pin ) and (9-Pin) X505 3-Port RS-232 (5-Pin) X506 6-Port RS-232 (3-Pin) X507 1-Port RS-422/485, 4-ch. D/I, 4-ch. D/O X508 1-Port RS-232 (5-Pin), 4-ch. D/I, 4-ch. D/O X509 2-Port RS-232 (3-Pin), 4-ch. D/I, 4-ch. D/O X510 1-Port RS-232 (3-Pin ), 5-ch. D/I, 5-ch. D/O, EEPROM 128K x2 X511 3-Port RS-485 X512 4-Port RS-232 (3-Pin) ,1-ch. RS-485 (will be available) Specifications Of ISaGRAF Embedded Controller 13 ICP DAS

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the ISaGRAF Book-C have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

product

14 Isolated digital input module with LED Display

product

13 Isolated O.C. output module

product

4 Isolated digital input & 8 output module

product

7 Digital input and 8 Digital Output module, Sink

product

AC-SSR relay output module

product

Relay output module