704A Packages 704A Packages Universal Data Test Set Highlights ● Rugged, Lightweight & Hand-Held Universal Analog/Digital Test Set ● Analog/Wideband TIMS, Signaling/Digit Capture, Digital Subscriber Line (DSL), Digital Data Services (DDS), DS0, BRI-ISDN & T1/FT1 ● Basic and Wideband Transmission Impairment Measuring Set (TIMS) to 1.5MHz with Nyquist Tones, Load Coil Detection, E, F and G Filters for DSL/High bit-rate Digital Subscriber Line (HDSL) Noise/Impulse Noise Measurements and Return Loss ● Signaling Package for DID-PBX, Station & Central Office (CO) Emulation, Digit Analysis & Wink Timing with Optional Types I-V E & M. Ideal for E911 and related services ● Enhanced “Class Services” Caller & Name ID Package ● Versatile DDS Test Package with 4-Wire DEMARC, DS0-OCU and DS0-DP, T1 and DTE/DCE Test Interfaces, including RS-232, V.35, RS-449 and RS-530 ● T1/FT1 Test Package features single keystroke BERT Testing Setup Additional Features Unique Features All Models All Models (704A-PKG2, -PKG3, -NTS1 & -NTS2) ● Send/Receive Tones manual or Pre-Programmed ● Load Coil Testing ● 3-Tone or Broadband Sweeps ● Pre-Programmed DSL Nyquist Frequency Tones ● Message Noise ● Single-screen readout of both TX & RX Frequencies and levels ● Notched Noise ● CO & PBX Switch Emulation ● Signal-to-Noise ● Includes E, F & G Filters for DSL/HDSL Noise/Impulse Noise ● Impulse Noise Measurements ● Analyze MF/DTMF Signals ● Filters: C-MSG; 3KHz; 15KHz; Program, E, F & G 704A-PKG2, 704A-NTS1 & 704A-NTS2 ● Measure Loop Voltage/Current ● Package includes OCU Emulation ● Measure Sealing Current ● Tests all DS0 logical network elements ● Dial & Hold ● Provides sealing current ● Return Loss, 105/110 Responder Automated Trunk ● Bursty-mode BERT for intermittent faults Testing, One-Touch 2713Hz Loopback Tone Mode, ● 4-Wire DDS Interface ● Built-in CSU/DSU 23-Tone Auto-Test for Signal Level, Envelope, Gain Slope, Envelope Delay, Intermodulation Distortion, Signal-to- 704A-PKG3, 704A-NTS1 & 704A-NTS2 Total Distribution, Signal-to-Noise Ratio ● Quick-view of T1 signal power level ● Emulates CO or PBX switch at the MDF or NID ● All required BERT patterns & loopbacks, including HDSL, ● TX/RX Nyquist tones and load coil detect from 4-Wire DDS Fractional T1 testing interface, jitter buffer and CSU line interface build-out ● DSX Equalizer “At-A-Glance” circuit analysis The Halcyon 704A Packages™ Universal Data Test Sets ● CO & PBX Switch Emulation (704A-PKG2,704A-PKG3, 704A-NTS1 and 704A-NTS2) are ● Comprehensive T1/FT1 Test Functions with CSU Emulation hand-held integrated test sets optimized for analog and digital ● One keystroke setup for Monitoring or BERT Testing ● CSU, NIU, V.54 & ADTRAN HDSL/PairGain Loop Codes with telecommunications. The users for all models consists of Automatic Arming DS0/DS1, Central Office (CO), Digital Operations Group (DOG), Special Services, and CO/OSP Construction Technicians. The 704A-NTS1 & 704A-NTS2 Test Set for all models are digital and analog with real digital ● Performs full Analog Transmission and Signaling, DDS CO, emulation, digital loop qualification features and emulation for DDS Field, Fractional T1 and Broadband TIMS CO and PBX switches. All models perform full-service broad- ● Built-in CSU for T1/DDS in single package without band TIMS and data tests. Each model’s primary purpose is changing modules data testing and qualification of facilities for DSL Services, ● All capabilities already installed and ready for use Analog Special Services and DID trunk testing, including ● Perfect for roving CO technicians and Special Services field Single-screen measurements for Pre-Wink, Wink and Answer technicians Delay parameters. 894 Faulstich Court�� San Jose, CA 95112-1361 www.cxrtelcom.com 408.200.3595� 408.200.3599 (FAX) Halc Halcy yon 704A P on 704A Packages ackages The 704A-PKG2, 704A-PKG3 and 704A-NTS1 include the rent and test Switched 56 Services. The 704A-PKG3 and 704A- above mentioned functions; the 704A-PKG2 also functions as a NTS1/704A-NTS2 include the addition of testing comprehen- DDS Test Set; 704A-PKG3 functions as a T1/FT1 Test Set and the sive T1/FT1 test functions. 704A-NTS1 functions as a DDS and T1 Test Set. Facilities Tested/Qualified Applications All models perform Facilities Tested/Qualified. These cate- Services Tested gories include the following: Cable Pairs, DS0 Crossconnects, All models perform the following Services Tested: DSL Circuits HDSL , ADSL, ISDN and POTS Facilities Testing, Smartjack test- (E, F and G Filters for Noise/Impulse Noise Measurement), DDS ing, customer wiring and CSU (cross-office and inter-office) (2.4kb to 56/64kb), POTS, Analog Special Services and PBX testing. The 704A-PKG2 includes Office Channel Unit (OCU) Trunks (with CO/PBX Emulation). The 704A-PKG2, 704A- testing. The unit also test all active circuit elements (even into NTS1/-NTS2 can be substituted for a Central Office (CO) switch other Telco CO) from the OCU. or PBX. These models include OCU Emulation with sealing cur- PHYSICAL (TIMS ONLY) (CONTINUED) Specifications • Dial: 16 Character DTMF generation, 12 character MF generation, 10 digit Dial Pulse generation IMPEDANCES • Measurements: Level (dBm), Frequency, Weighted Noise, Notch • Analog: 100, 135, 600, 900, 1200 Ohms and Bridged Noise, Signal to noise ratio, Impulse Noise, • DDS/T1: 135 Ohms, Monitor Return Loss, 23-Tone Sequence (RMS level/ • T1/FT1: 100 Ohms Terminated, Monitor and Bridged frequency, individual level/frequency, IMD, EDD, S/TD, SNR), Advanced Caller ID CND/CNAM INTERFACES (optional), Line voltage, current and ring • All Models: 2- or 4-Wire RJ-11, Dual Bantam (210) connector voltage, Load Coil Detect, MF/DTMF/Dial Pulse • 704A-PKG2: Include 4-Wire RJ-48S, DS0 Bantam, DB9 for analysis Bit/Byte Clock • 704A-PKG3 & 704A-NTS1 Dual Bantam and RJ-48C. Two receivers for timing TIMS slip testing SIGNALING • Signaling Interfaces: Emulate network and terminal end of Loop INTERFACES (DDS ONLY) Start, Ground Start, Direct Inward Dial, E&M I-IV, • OCU Emulation: 4-Wire Loop 8-pin modular RJ-48S Originate or terminate call, Analyze digits, perform • Sealing Current Supply: -24 VDC, limited to 20mA transmission tests max • 4-Wire Interface: DDS standard 8-pin modular RJ-48S • Signaling Modes: MF/DTMF/Dial Pulse analysis • RS-232 Interface: OPT-H3/H5 • CO Emulation: Wink start or immediate start • V.35 Interface: OPT-H3/H5 • Measurements: Pre-wink, wink duration and answer delay for • RS-449 Interface: OPT-H3/H5 up to 999ms with 1ms resolution • RS-530 Interface: OPT-H5 • Loop Current Detection: Loop current detector must exceed 20ms to detect a valid off-hook state • DTMF Generation: Transmit level of -7 ±0.2dBm, with 1.5dB twist • Operating Modes: CSU/DSU emulation, SW56K, 64K Clear, • MF Generation: Transmit level of -7 ±0.2dBm Primary and Secondary channels • Dial Pulse Generation: -10 Pulses per second with 60% break and (fully independent) 250mS inter-digit time • Primary Channel: DDS standard 8-pin modular RJ-48S • PBX Emulation Mode: Wink start or immediate start with pre-wink • Secondary Channel: Bellcore TR-NPL-000157 time of 1 sec and wink duration of 250mS ± 2mS • Loop Rates: 2.4, 3.2, 4.8, 6.4, 9.6, 12.8, 19.2, 25.6, 56.0 and • Measurements: Up to 9999mS maximum post wink time with 72 (64)Kbps 1mS resolution and ± 1mS accuracy • Termination: 135 Ohms impedance (AT&T Publication 62310) • Battery Feed: -48 VDC 400 ohm DC feed limited to 24mA • Cable Gauge: 19 to 26 AWG • MF Receiver: All 15 valid MF tones received at levels as low as -30dBm CLEI CODES • DTMF Receiver: 16 digit receiver (1-9, 0, A, B, C, D, *, #) • DDS: TETMAAG7AA, DDETEAFFJAA • Dial Pulse Receiver: 12 digit receiver (1-9, 0, *, 3) Range is from 3 • TIMS: TETMAAE7AA, TETMAAF7AA to 29 pulses per second with a 10 to 90% break PHYSICAL DTMF ANALYSIS • Dimensions (L x W x H): 9.5-in x 6.33-in x 3.31-in • Frequency Meas: A high/low group frequency accuracy of ±3Hz • Weight: 4 lbs. with 1Hz resolution • Battery: 4 Hours continuous operation from the internal • Level Meas: A high/low tone group range accuracy of +1.5 7.2 VDC NiMH pack. Charge time: 14 hours to -28dB with 0.1dB resolution and ±0.5dB • Battery Charger/AC Adapter: Input 120 VAC, Output 9 VDC, 1A, Power connector accuracy negative shell, positive center conductor • Timing Meas: 1mS to 65.5 seconds with 1mS resolution and • Power: Input 120 VAC or Internal NiMH Rechargeable ±1mS accuracy battery. Operate Time > 4 Hrs. • Tone Acceptance: Maximum twist of ±10 dB with 35 mS minimum • Operating Environment: 32° to 122°F (0° to 50°C), 0 to 95% R.H. tone duration. 18 dB maximum dial tone level (Non-Condensing) tolerance • Power Requirements: 4 Watts at 115 VAC, 60Hz nominal; Output 9 VDC external DC power supply. Internal 7.2 VDC NiMH CLASS SERVICES TESTING (OPTIONAL) pack • Enhanced Caller/Name ID: Test Functions • Audio & Display: Built-in speaker with volume control. Display is • Timing Measurements: 1mS to 60 seconds with 1mS resolution and LCD (4 line x 20 character) ±1mS accuracy • Receiver Sensitivity: Carrier must be received at -45dB minimum PHYSICAL (TIMS ONLY) receiver sensitivity • Longitudinal Balance: Better than 60dB from 200Hz to 1.5MHz • FSK Data Detection: Continuous phase coherent FSK detection • Line Hold: Electronic, internally current limited to 24mA on (1200/2200Hz ±1%) @ 1200 BPS • Ring Voltage Measurements: 40 to 140 VAC with 1 volt resolution and ±2 V either the 2W or 4W-XMT port when Off-Hook accuracy Halc Halcy yon 704A P on 704A Packages ackages GENERATOR DDS (CONTINUED) • Variable Tone: Frequency adjustable from 50Hz to 1.5MHz in DS0/DTE INTERFACE (CONTINUED) 1Hz steps: accurate to within ±0.5Hz • DTE Interface: OPT-H3 provides RS-232, RS-530 and CCITT V.35 • Fixed Tones: Program 50Hz, 100Hz, 1kHz, 5kHz, 8kHz, and Interface; OPT-H5 provides RS-449, adapter, in 15kHz. (transmit level fixed at 0.0dBm) addition to RS-232, RS-530 and CCITT V.35 Interface • ADSL Tones: 28kHz, 40kHz, 48kHz, 82kHz, 196kHz, 392kHz • Receiver Sensitivity: Subrates: -34, -40dB, 56 and 72 (64)Kbps: -48dB (level adj. +13dBm to –40dBm) • Signal amplitude: 9.6 and 12.8Kbps: 1.66 V ; All other rates: max • Wideband Sweep: 400Hz to 3200Hz in 200Hz steps, 4800Hz, 3.32 V max 8000Hz, 28kHz, 32kHz, 36kHz, 48kHz, 80kHz, • Band Rejection: C-message filter (AT&T Publication 62310) 82kHz. Level adjustable from +13dBm to –40dBm • 3–Tone Slope: 404Hz, 1004Hz, 2804Hz, each at ±0.5Hz. Level FREQUENCY adjustable in 4 steps of 0, -10, -13 and –16dBm • Frequency Generator: 10 to 90kHz +0.5% ±0.2dBm • Frequency Measurement: 0 to 90kHz +0.25% • 2713Hz Loop Back Generated at at ±0.5Hz. Level adjustable as in • Frequency Jitter Tolerance: +5% 3-Tone Slope • Level Accuracy: 600/900/1200 Ohms mode ±0.1dB from 400 to MISCELLANEOUS 10,000Hz; ±0.5dB from 200 to 30,000Hz • Cable Lengths: 0 to 1500 feet • 100/135 Ohm 4W Mode: ±0.2dB from 400 to 30,000. Optional wideband • Pulse Width: 15.6ms nominal 135 Ohms; ±0.5dB from 250 to 1.5MHz • Pulse Amplitude & Wide Rations: ±5% Level adjustable from +13dBm to –40dBm in • Clock Modes Network (slave), Internal (master) and External 0.1dB steps (DTE) • 23-Tone Test: Generate 23-Tone sequence per IEEE-1995 at • Metallic Test Aids: Short, R-R1 and T-T1, R1-T1 and 135 Ohms –6dBm to –40dBm. Measures individual quite termination frequencies and level, RMS composite tone, IMD, • Load Coil Detect: Auto Detect up to 3 Load Coils, Range: Facility Loss EDD, S/TD and S/NR < 45dB • Return Loss: Continuous generation of band limited noise signal sent at –6 ±1.0dBm in each of three bands • DTMF Generation: XMT level of –7 ±0.2dBm, w/1.5dB twist: freq T1/FT1 Accurate to –0.5Hz, 75mS on, 75mS off TRANSMITTER • T1 Interface: SIDE A - Bantam Transmit and Receive in RECEIVER parallel w/ RJ-45 • Level Accuracy: +13 to - 72 dBm SIDE B - (Reference Input) Bantam jacks For 600, 900 and 1200 Ohms impedance: • T1 Signal Format: DS1 PCM, 1.544MHz ±50Hz ±0.2dB from 200Hz to 20,000Hz • Operating Modes: Full T1 or Fractional T1 Nx56/64 DS0 DS1 Signal For 135 and 100 Ohms impedance: • Waveshape: Meets T1.403 specifications ±0.5dB from 1,000Hz to 600,000Hz and ±1dB from • DS1 Line Level: 0 ±0.2dBdsx (6.0 V p-p) 600,000Hz to 1,500,000Hz • Line Codes: AMI, B8ZS • Frequency: For 50 to 1,500,000 Hz, frequency measurement • Clocksource: Recovered from Receiver or internally generated accuracy is ±1 Hz resolution with 0.005% accuracy 1.544MHz ±30Hz with 1Hz resolution • Framing: SF, ESF, SLC-96, Unframed • Noise: 15 to 95dBrn with 1dBrn resolution and ±1dBrn • FT1 Fill Date: Idle code (7F) sent in unused DS9 time slots accuracy from 20 to 90dBrn 15-1 20-1 23-1 • Test Patterns: QRSS, 2047, 2 , 2 , 2 , 3 in 24, • Noise Filters: C-MSG, 3KHz Flat (D), Program, 15KHz Flat and All 1s, All 0s, Alt 1/0, 2 in 8, 1:7, 63 and 511 E, F and G • Error Injection: Single bit or streamed BER at 1e-3, 1e-4, 1e-5, 1e-6 • Notched Noise: 1010Hz notch, with a minimum of 50dB or 1e-7 attenuation in the band of 995 to 1025Hz • Line Build Out: 0, -7.5, -15, 22.5dB • Signal to Noise Ratio: Holding tone (1004Hz) must be in the range of • DSX Pre-Equalizer: 5 steps for cable lengths to 655 feet +6 to –45dB: Measured S/N ratio range from 10 to 55dB with 1dB resolution and ±2dB accuracy ANALYSIS MODES • 3-Level lmpulse Noise: Threshold can be set from 30 to 90dBrn: 3 level • BERT Analysis: Bit Errors (BE), Errored Seconds (ES), Bit Error Rate difference fixed at 4dBrn with a measurement (BER) , %Error Free Seconds (%EFS), Severely accuracy of ±1dBrn. Blanking interval fixed at Errored Seconds (SES), % Severely Errored Seconds 125ms with 3 independent counters (%SES), Elapsed time • 23-Tone Test: Generate 23-Tone sequence per IEEE-743 (1995 Edition) at -6dBm to -40dBm. Measures individual frequencies and level, RMS Composite Tone, IMD, EDD, S/TD and S/NR • Return Loss: Three bands: ERL, SRL-HI, SRL-LO; Range of 0 to -30dB with 1dB resolution and ±1dB accuracy. Continuous generation of band limited noise signal sent at -6 ±1.0 dBm in each of 3 bands • Line Voltage Measurement 2 to 85 VDC; 0.1 V resolution and±1 V accuracy • Line Current Measurement 10 to 80mA; 0.1mA res. and ±1mA accuracy DDS DS0/DTE INTERFACE • DS0 & Bipolar Interface: Dual ‘Bantam’ • DS0 & Bipolar Clock Interface: 15-pin HD D-sub • DS0 Rates: 2.4, 4.8, 9.6, 19.2, 38.4, 56.0, 64Kbps • DS0 Transmit Signal: ‘0’: 0.7 V , `1’: 3.5V max min • DS0 Receive Signal: ‘0’: 0.9 V , `1’: 1.6V max min • Bipolar Rate: 64Kbps • Bipolar RCV & XMT Signals: ‘0’: 0.9 V , `1’: ±3.5 to ±5.5V max Halcyon 704A Packages Halcyon 704A Packages Ordering Configurations Model Description 704A-PKG2 Wideband 1.5MHz TIMS & Signaling Package with enhanced DDS Test Functions. 704A-PKG3 Wideband 1.5MHz TIMS & Signaling Package with T1/FT1 Test Functions. Wideband 1.5MHz TIMS & Signaling Package with enhanced DDS Test Functions and T1/FT1 Test 704A-NTS1 Package. Wideband 1.5MHz TIMS & Signaling Package with enhanced DDS Test Functions, T1/FT1 Test 704A-NTS2 Package and BRI-ISDN Test Package. Option Description OPT-C Adds T1/FT1 Test Functions to 704A-PKG2. (Factory Retrofit) OPT-H Adds enhanced DDS Test Functions to 704A-PKG3. (Factory Retrofit) OPT-H3 Adds DTE/DCE Test Suite with RS-232, V.35 & RS-530 Test Functions to 704A-NTS1/NTS2 & 704A-PKG2. OPT-H4 Adds Remote Control Test Interface to 704A-xxx Test Set platforms. OPT-H5 Adds DTE/DCE Test Suite with RS-232, V.35, RS-449 & RS-530 Test Interfaces to 704A-NTS1/NTS2 & 704A-PKG2. OPT-N Adds BRI-ISDN Test Functions to 704A-NTS1 Test Set. (Factory Retrofit) Please contact CXR Telcom for any further clarification on any of the 704A Universal Data Test Set packages. Other product and company names referenced herein may be trademarks or trade names of their respective owners. Features and specifications are subject to change without notice. © 2005 CXR/Larus Corporation (P/N 96-50000-504, Rev. A)