12-Channel, 12-Bit PMC Analog Input/Output Board With Eight Simultaneously-Sampled Wide-Range Inputs at 2.0 MSPS per Channel, Four Analog Outputs, and 16-Bit Digital I/O Port Available Q2 2003 � 8 Differential Analog Inputs with Dedicated 12-Bit, 2.0 MSPS ADC per Channel � True Simultaneous Sampling of all Inputs; Minimum Data Skew � Sampling Rates to 2.0 MSPS per Channel (16 MSPS Aggregate Rate) Software-Selectable Input Ranges: ±10V, ±1V, ±100mV � 64-Ksample Analog Input FIFO Data Buffer � Supports DMA Transfers in Two Channels in Block-Mode or Demand-Mode � 4 Analog Output Channels with Direct Register Access � 16-Bit Bidirectional Digital I/O Port � Sampling Controlled by Internal Rate Generator, by Software Trigger, or Externally � Input Frequency response to 900kHz on ±10V Range, 10kHz on ±100mV Range. (Refer to the PMC-12AISS44AO4 product specification for a wideband version of this product). � On-Demand Internal Autocalibration � Hardware Sync I/O for Multiboard Operation � Integral Dual-Conversion Precision Analog Power Supplies � Completely Software-Configurable; No Field Jumpers � Conforms to PCI Local Bus Specification, Revision 2.3, with Universal Signaling � Single-width PMC Form Factor, with Integral EMI Shield � Simultaneous Sampling � Low-Level Inputs � Instrumentation � Transducer Inputs � Event Capture � Acoustic Sensor Inputs � Dynamic Test Systems � Voltage Control � Closed-Loop Systems PRELIMINARY REV-072104 8302A Whitesburg Drive · Huntsville, AL 35802 Phone: (256) 880-8787 or (800) 653-9970 FAX: (256) 880-8788 Email: Sales@GeneralStandards.com The 12-Bit PMC-12AISS8AO4 analog I/O board samples and digitizes eight input channels simultaneously at rates up to 2.0 million samples per second for each channel. The resulting 12-bit sampled data is available to the PCI bus through a 64K-Sample FIFO buffer. All data is channel-tagged. The analog inputs can be sampled in groups of 1 through 8 channels, and the sample clock can be generated either from an internal rate generator, through software, or by external hardware. Both burst and continuous sampling modes are supported. Input ranges are software-selectable as ±10V, ±1V, or ±100mV. The inputs can be divided into two channel groups that can be assigned input ranges independently. Four analog output channels provide software-selected output ranges of ±2.5V, ±5V or ±10V, and are accessed directly through dedicated control registers. A 16-Bit bidirectional digital port can be configured as two independent byte-wide ports. An on-demand autocalibration feature determines offset and gain correction values for each input and output channel, and the corrections are applied subsequently during normal operation. A selftest switching network routes output channels or calibration reference signals to the analog inputs, and permits board integrity to be verified by the host.. Loopback Channel-00: One of 8 Identical Input Channels Selftest Input 12-Bit PGA Switching ADC Vref 8 Differential 12-Bit Analog 4 Analog DAC (4) Inputs Outputs Input Channels 01-07 Digital I/O (16) Local and Sync I/O Controller Host Conn (PCI) Regulated Power Voltages +5VDC Power Conversion Data Vref Buffer PCI Local Bus Interface Adapter Figure 1. PMC-12AISS8AO4; Functional Organization This product is functionally compatible with the IEEE PCI local bus specification Revision 2.3, and supports the "plug-n-play" initialization concept. System connections are made at the front panel through a high-density dual-ribbon 80-pin connector. Power requirements consist of +5 VDC in compliance with the PCI specification, and analog power voltages are generated internally. All operational parameters are software configurable. Operation over the specified temperature range is achieved with conventional convection cooling. 8302A Whitesburg Drive · Huntsville, AL 35802 Phone: (256) 880-8787 or (800) 653-9970 FAX: (256) 880-8788 Email: Sales@GeneralStandards.com O At +25 C, with specified operating voltages Analog Input Characteristics: Configuration: Eight differential analog input channels; Dedicated 12-Bit ADC per channel. Optional 4-Channel version available. Voltage Ranges: Independently assignable between two groups of input channels as: ±10V, ±1V or ±100mV full scale. Input Impedance: 20 Megohms Line-Line in parallel with 40pF, typical. Bias Current: 50 nanoamps maximum, all ranges Crosstalk Rejection: 70dB typical, DC-500kHz Signal/Noise Ratio (SNR): ±10V Range: 75dB, ±1V: 70dB, ±100mV: 65dB. Inputs shorted. (10 Hz to small-signal bandwidth. Signal = Fullscale-0.3dB) Common Mode Rejection: ±10V Range: 90dB, ±1V Range: 100dB, ±100mV Range: 105dB. Typical, DC-100Hz, CMV = ±11V, Vin = Zero. Overvoltage Protection: ±40 Volts with power removed; ±25V with power applied. Analog Input Transfer Characteristics: Resolution: 12 Bits (0.0244 percent of FSR) Maximum Sample Rate: 2.0 MSPS per channel Sampling Mode:: Simultaneous; 1 through 8 channels Range Midscale Accuracy * Fullscale Accuracy * DC Accuracy: ±5-10V ± 0.8mV ± 12mV (Maximum composite error ±1-2.5V ± 1.8mV ± 3mV after autocalibration) ±100mV ± 0.3mV ± 0.6mV * Differential input mode. Add ±1.3mV for single-ended input mode. Small Signal Bandwidth, ±10V Range: 900kHz, ±1V: 80kHz, ±100mV: 10kHz -3dB, Typical: * Power Bandwidth, Vpp*Hz, 28,000 * Range, Typical. E.g.: 2.8VP-P at 100kHz,.±10V range. -3dB, Typical: * Integral Nonlinearity: ±0.035 percent FSR (FSR = fullscale range; e.g.: 20Von ±10Vrange). Differential Nonlinearity: ±0.030 percent FSR. * Refer to the PMC-12AISS44AO4 product specification for a fixed-range, wideband version of this product. Analog Input Operating Modes and Controls Input Data Buffer: 64K-sample FIFO; Optional 16K-sample buffer available Sample Clock Sources: Internal rate generator; External Hardware Sync I/O, Software clock. Sampling Modes: Continuous sampling, and triggered burst. Programmable from 488-2,000,000 sample clocks per second. Divides 32MHz Internal Rate Generator: master clock to sample rate. External Clock I/O: TTL, bidirectional. Zero to 2,000,000 sample clocks per second. Input Data Format: Selectable as offset binary or as two's complement. All channels tagged. 8302A Whitesburg Drive · Huntsville, AL 35802 Phone: (256) 880-8787 or (800) 653-9970 FAX: (256) 880-8788 Email: Sales@GeneralStandards.com Analog Output Characteristics: Configuration: Four single-ended output channels. (Ordering option) Voltage Ranges: ±10, ±5 or ±2.5 Volts; Independent of analog input ranges. Output Resistance: 1.0 Ohm maximum Output protection: Withstands sustained short-circuiting to ground Load Current: Zero to ±5ma per channel Load Capacitance: Stable with any load capacitance Noise: 2.0mV-RMS, 10Hz-100KHz typical Glitch Impulse: 5 LSB-nSec typical, all ranges Analog Output Transfer Characteristics: Resolution: 12 Bits (0.0244 percent of FSR) Output Clocking: Direct register access. Outputs can update immediately upon receiving each new value from the bus, or can update synchronously from an internal or external clock. Maximum practical clocking rate is 400KSPS per channel. DC Accuracy: Range Midscale Accuracy ±Fullscale Accuracy (Max error, no-load) ±10V ±10mV ±15mV ±5V ±4mV ±7mV ±2.5V ±2mV ±4mV Settling Time: 4us to 1-LSB, typical with 50-percent fullscale step, no-load. Crosstalk Rejection: 65 dB minimum, DC-10 kHz Integral Nonlinearity: ±0.04 percent of FSR, maximum Differential Nonlinearity: ±0.03 percent of FSR, maximum Digital I/O Port: 16-Bit bidirectional I/O port. Standard TTL levels. Direct register Access. Byte or word configuration. 20 mA loading when configured as an output port. 0.1 mA source when configured as inputs. PCI Compatibility: Conforms to PCI Specification 2.3, D32 read/write, 33MHz, universal (5V/3.3V) signaling, Supports "plug-n-play" initialization, Provides one multifunction interrupt, Supports DMA data transfers in two channels as bus master in block mode or demand mode. 8302A Whitesburg Drive · Huntsville, AL 35802 Phone: (256) 880-8787 or (800) 653-9970 FAX: (256) 880-8788 Email: Sales@GeneralStandards.com Power Requirements +5VDC ±0.25 VDC at 1.5 Amp maximum, 1.1 Amp typical. Maximum Power Dissipation: Side-1: 6.5 Watts. Side 2: 1.0 Watt. Mechanical Characteristics Height: 13.5 mm (0.53 in) Depth: 149.0 mm (5.87 in) Width: 74.0 mm (2.91 in) Shield: Side-1 is protected by an EMI shield. Environmental Specifications Ambient Temperature Range: Operating 0 to +65 Degrees Celsius inlet air: Storage: -40 to +85 Degrees Celsius Relative Humidity: Operating: 0 to 80%, non-condensing Storage: 0 to 95%, non-condensing Altitude: Operation to 10,000 ft. Cooling: Conventional convection cooling; 150 LFPM Specify the basic product model number followed by an option suffix "-A-B-C-D", as indicated below. For example, model number PMC-12AISS8AO4-8-64K-4 describes a board with eight input channels, four output channels, and a 64 Ksample data buffer. Optional Parameter Value Specify Option As: Number of Input Channels 8 Input Channels A = 8 4 Input Channels A = 4 Buffer Size 64 Ksamples B = 64K 16 Ksamples B = 16K Analog Outputs Four Analog Outputs C = 4 No Analog Outputs C = 0 General Standards Corporation assumes no responsibility for the use of any circuits in this product. No circuit patent licenses are implied. Information included herein supersedes previously published specifications on this product and is subject to change without notice. 8302A Whitesburg Drive · Huntsville, AL 35802 Phone: (256) 880-8787 or (800) 653-9970 FAX: (256) 880-8788 Email: Sales@GeneralStandards.com Table 1. System I/O Connector ROW-A ROW-B PIN SIGNAL PIN SIGNAL 1 OUTPUT RTN 1 DIGITAL RTN 2 ANA OUT 00 2 DIO 00 3 OUTPUT RTN 3 DIGITAL RTN 4 ANA OUT 01 4 DIO 01 5 OUTPUT RTN 5 DIGITAL RTN 6 ANA OUT 02 6 DIO 02 7 OUTPUT RTN 7 DIGITAL RTN 8 ANA OUT 03 8 DIO 03 9 INPUT RTN 9 DIGITAL RTN ROW A ROW B 10 INPUT RTN 10 DIO 04 11 INP00 LO 11 DIGITAL RTN 12 INP00 HI 12 DIO 05 13 INPUT RTN 13 DIGITAL RTN PIN 40 14 INPUT RTN 14 DIO 06 15 INP01 LO 15 DIGITAL RTN I/O 16 INP01 HI 16 DIO 07 CONN 17 INPUT RTN 17 DIGITAL RTN 18 INPUT RTN 18 DIO 08 19 INP02 LO 19 DIGITAL RTN PWB 20 INP02 HI 20 DIO 09 21 INPUT RTN 21 DIGITAL RTN 22 INPUT RTN 22 DIO 10 23 INP03 LO 23 DIGITAL RTN PIN 1 24 INP03 HI 24 DIO 11 Panel Pin-view 25 INPUT RTN 25 DIGITAL RTN 26 INPUT RTN 26 DIO 12 Figure 2. System Input Connector 27 INP04 LO 27 DIGITAL RTN 28 INP04 HI 28 DIO 13 System Mating Connector: 29 INPUT RTN 29 DIGITAL RTN Standard 80-pin 0.050" dual-ribbon 30 INPUT RTN 30 DIO 14 socket connector: 31 INP05 LO 31 DIGITAL RTN 32 INP05 HI 32 DIO 15 Robinson Nugent P50E-080-S-TG, 33 INPUT RTN 33 VTEST RTN or equivalent. 34 INPUT RTN 34 VTEST 35 INP06 LO 35 DIGITAL RTN 36 INP06 HI 36 OUTPUT CLK I/O 37 INPUT RTN 37 DIGITAL RTN 38 INPUT RTN 38 INPUT TRIG I/O 39 INP07 LO 39 DIGITAL RTN 40 INP07 HI 40 INPUT CLK I/O 8302A Whitesburg Drive · Huntsville, AL 35802 Phone: (256) 880-8787 or (800) 653-9970 FAX: (256) 880-8788 Email: Sales@GeneralStandards.com