BIOS

New AMI BIOS Core 8, in-system programmable flash ROM CPU, memory and IDE auto-detection/selection Integrated VGA, and Ethernet BIOS ROM USB Mass Storage support and booting capability (Floppy, HDD, CDROM) Password protection, BIOS post, system and video BIOS shadowing Extensive setup with remappable serial/parallel ports Operation without disk, keyboard and video Remote BIOS through serial port

Cache

Cache Level 1 Level 2 Pentium M (90nm) 32 KB 2048KB, full speed Pentium M (130nm) 32KB 1024KB, full speed Celeron M (90nm) 32K 512KB, full speed Celeron M (130nm) 32KB 512KB, full speed

Chipset

400 MHz system bus to processor PCI burst mode transfers up to 512MB/s (64-bit/133MHz) Two 64-bit wide PCIbusses with 66 MHz One 32-bit wide PCIbus with 33 MHz

Communications Controller

242 bytes non-volatile CMOS RAM

EIDE

Ultra ATA/100 sync. DMA mode up to 100 MB/s PIO mode 4 and bus master IDE up to 16 MB/s Two devices supported via local EIDE connector and two devices alternate with PMC32/33 rear I/O

Environmental

Note: For detailed information about the operating temperature behavior of the board of any style it is absolutely necessary to consult the manual. The processor type, speed, altitude, the use or not use of Ethernet or video, ambient conditions and the type of cooling influences the board temperature range. Operating Storage Standard 0C to +70C -40C to +85C Extended -40C to +85C -40C to +85C Humidity: Operating: 5-95%@40C Storage: 5-95%@40C Altitude: Operating: 15,000 ft. (4.5km) Storage: 40,000 ft. (12km) Shock (3 axis, up & down, 5 hits/direction) Style (C,I,1,3): 12g/6ms Vibration: Style (C,I,1,3): 2g rms@5 to 100 Hz

EPROM

512 Kbit serial EEPROM for non-volatile user data

Flash Memory

Internal 2.5" IDE hard disk drive or 2.5" flash drive (for extended temperature range and higher shock/vibration immunity)

GPIO

Highly integrated Dual Channel Ethernet controller with 64-bit/66MHz PCI local bus mastering 64KB transmit and receive FIFO 10/100/1000 BaseT auto-negotiation Versions with front I/O available Rear Ethernet: VITA 31.1-2003 compliant

Graphic Processor

8 bits general purpose I/O Multiplexed with DVI output

Keyboard/Mouse

PS/2 compatible

LPC I/O

Front panel LED System control

Mechanical

6U, 2 slot wide 233x160x40.64mm (including hard disk)

Memory

DDR 200 High-speed registered DDR SDRAM 72-bit wide with error correction (ECC) 512 MB to 2 GB with soldered chips

MTBF

Calculations are available in accordance with MIL-HDBK-217.

PMC #1

One high bandwidth 64-bit/133MHz PMC and one 32-bit/33MHz PMC interface Enhancement to processor PMC standard VITA 32-2003 (non-monarch) Cardbus adapter available on PMC2 Note: The 32-bit/33MHz PMC slot is not available with VGA or ethernet on the front, IDE secondary installed

Power Connector

+5V, +3.3V Total power max. 7.5W +/-12V 100mA each

Power Consumption

w/o keyboard, hard disk, modules, Ethernet (no link), measured at DOS prompt, no power savings Processor, Memory 5V 3.3V Total Power 1.0 GHz, 1GB 1.8A 5.9A 28.5 W 1.3 GHz, 1GB 2.2A 5.9A 30.5 W 1.4 GHz, 2GB 2.0A 5.9A 29.5 W 1.6 GHz, 2GB 2.7A 5.9A 33.0 W 1.8 GHz, 2GB 2.5A 5.9A 32.0 W w/o keyboard, hard disk, modules, Windows XP, 3D graphics active. Both Gigabit Ethernet channels linked, CPU running at instruction mix for maximum power consumption Processor, Memory 5V 3.3V Total Power 1.0 GHz, 1GB 2.4A 7.5A 36.8W 1.3 GHz, 1GB 4.6A 7.5A 47.8W 1.4 GHz, 2GB 2.7A 7.5A 38.3W 1.6 GHz, 2GB 5.4A 7.5A 51.8W 1.8 GHz, 2GB 4.8A 7.5A 48.8W

Power Requirements

+5V, +3.3V Required +/-12V Only if required by installed PMC module

Processor

Scaleable processing power with flexible processor design Intel Pentium M processor: 1.4GHz to 1.8GHz Intel Celeron M processor: 1.0GHz to 1.3GHz High efficiency on-board switching regulator(DC/DC) Fanless cooling with heat sink

RTC

RTC 146818 compatible, on-board Li-battery

Safety Criteria

Designed to meet standard UL1950, CE Class A, FCC-A

Serial

Two async. 16550 compatible full duplex serial channels at rear I/O High-speed transfer up to 115.2 kbaud with 16 byte FIFO's User selectable RS232/422/485/interface COM1 optional available on front

Technology

CPU die software readable from -65C to +127C, 1C increments and 3 board, heat sink, card edge temperature sensors

Timer

Activates IRQ under software control (200 nano s-20ms)

USB

One USB 2.0 connector at front Two universal serial bus channels at rear

VGA

NVIDIA GeForce 4 420 Go VP9 Board version 2.x only 256-bit 3D and 2D graphics accelerator On-chip 32 Mbytes frame buffer (66-190 MHz) 32-bit/66MHz PCI interface Dual CRTC/simultaneous Dual Display 350 MHz Palette-DAC for analog VGA (up to 1600x1200) DVI-I interface (PanelLink) for TFT displays up to 1024x768, single channel DVI (165 MHz), EDID display PnP supported Fully compliant support for OpenGL 1.2 for all supported Windows operating systems and Linux ATI MOBILITY RADION VP9 board version 3.x only, RoHS version 128/256-bit 2D, 3D and multimedia graphics accelerator Local DDR memory (16MB or 64MB)@125 MHz to 200 MHz 32-bit/66MHz PCI interface Dual independant CRT controllers to support two asynchronous simultaneous display paths RAMDAC (300MHz to 400MHz) for analog VGA (1600x1200) TDMS transmitter up to 165 MHz (1024x768 at 60 Hz); DVI Full support of OpenGL 1.3 (Windows) and xFreeX86 (Linux) Support for DirectX 6.0 to DirectX 8.1 under Windows

Watchdog Timer

Watchdog 1: 4.8s to 76s, 0.6s increments Watchdog 2: 1 min to 255min, 1 min increments User programmable