GE INTELLIGENT PLATFORMS Telum ASLP10
Specifications
BIOS
New AMI BIOS Core 8, in-system programmable Flash ROM CPU, memory and IDE auto-detection/selection Integrated Ethernet BIOS ROM USB Mass Storage support and booting capability (floppy, HDD, CDROM) Password protection, BIOS post, system BIOS shadowing Operation without disk, keyboard and video
Cache
Cache Level 1 Level 2 Pentium M (90nm) 32 KB 2048 KB, full speed Celeron M (90nm) 32 KB 512 KB, full speed
Chipset
533 or 400MHz system bus to processor One PCI Express x4 bus with 2 Gbytes/s transfer rate to Ethernet One PCI Express x8 bus with 4 Gbytes/s transfer rate to AMC interconnect – AMC.1 Type 8
Communications Controller
242 bytes non-volatile CMOS RAM
EIDE
Ultra SATA/150 sync. DMA mode up to 150 Mbytes/sec Two SATA devices (AMC.3 Type S2) supported via AMC connector
Environmental
Note: For detailed information about the operating temperature behavior of the board of any style it is absolutely necessary to consult the manual. The processor type and speed, altitude and the type of cooling influence the board temperature range. Range Operating Storage Standard 0 °C to +55 °C -40 °C to +85 °C Extended -40 °C to +55 °C -40 °C to +85 °C Humidity Operating: 5 – 95% @ 40 °C Storage: 5 – 95% @ 40 °C Non condensing Altitude Operating: 15.000 ft. (4.5 km) Storage: 40.000 ft. (12 km) Shock Style: 1, 3 12g / 6 ms, 3 axis, up & down, 5 hits / direction Vibration Style: 1, 3 2 g rms @ 5–100 Hz, 1 hour each axis
EPROM
512 kbit serial EEPROMs for non-volatile user data
Flash Memory
Standard 1 GB Flash Other Flash sizes on request
GPIO
Highly integrated Dual Channel Ethernet Controller – AMC.2 Type E2 Serdes type 1000Base-BX connection via AMC connector
Keyboard/Mouse
Support via USB port
LPC I/O
Front panel LED system control Hot swap (blue), LED 1 (red) (failure, out of service status) LED 2 (green) and LED 3 (amber) available for applications
Mechanical
Single width, full height 180.6 x 73.5 x 28.95 mm (without front bezel)
MTBF
Calculations are available in accordance with MILHDBK-217.
Power Consumption
For detailed information see the manual. Pentium M Typical Power 2.0 GHz, 1 GB 38 W (FSB 533MHz) 1.4 GHz, 512 MB 29 W 1.0 GHz, 512 MB 24 W (Celeron M)
Power Requirements
+12V Module power +3.3V Management power, 0.1A max.
Processor
Scalable processing power with flexible processor design Intel Pentium M processor: 1.4 GHz to 2 GHz Intel Celeron M processor: 1 GHz High efficiency on-board switching regulator (DC/DC) Fanless cooling with heat sink
RTC
RTC 146818 compatible
Safety Criteria
Designed to meet: FCC 47 CFR Part 15 Class A (USA) EN 55022:1998/A1:2000/A2:2003 Class A ITE (EU) ICES-003 Issue 3 Class A (Canada) VCCI Class A ITE AS/NZ CISPR 22:2002 Class A (Aus. New Zealand) EN 55024:1998/A1:2001/A2:2003 (EU) UL60950-1 (USA) CSA 22.1 No. 60950-1-03 (Canada) EN 60950-1 (EU) CE Mark
SDRAM
High-speed registered DDR SDRAM 72-bit wide with error correction (ECC) 512 Mbytes to 2 Gbytes with soldered chips 2 Gbyte availability depends on 1Gbit component availability
Serial
TxD/RxD, RTS/CTS on AMC interconnect
Technology
CPU die and board temperature software readable from –65 °C to +127 °C
Timer
Integrated in 6300ESB chipset Includes three timers comparators One-shot and periodic interrupts supported
USB
One USB 2.0 connector at front Universal serial bus channels at rear optional (customer specific)
Watchdog Timer
Integrated in chipset Two stage watchdog with independent count values First stage drives NMI or SMI, second stage drives reset Configurable granularity from 1µs to 10 minutes
Features
- 1 GB Flash (standard), others on request
- Addresses up to 2 GB DDR2 SDRAM (400MHz) with ECC
- Carrier Grade Linux Support
- Celeron® M processor 1GHz
- Common reference clock (CLK3) support
- Hot Swap compliant
- Intel® Pentium® M processor 2GHz, Intel® LV
- IPMI ver.1.5 acc. to AMC.0
- One USB 2.0 port on front
- Optional –40 °C to +55 °C
- PCI Express x8 data port AMC.1 Type 8 on port 4 to 11
- Pentium® M processor 1.4GHz and Intel® ULV
- Single width, full height AMC.0 form factor
- Two Gigabit Ethernet ports (Serdes type) on rear I/O AMC.2 Type E2 on port 0&1
- Two SATA on rear I/O AMC.3 Type S2 on port 2&3
- Watchdog, temperature sensor
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the Telum ASLP10 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods