CP9 ® High Performance 6U CompactPCI Embedded Computer Features ® ® • Intel Pentium M processor, 1.4 GHz to 1.8 GHz and ® ® Intel Celeron M processor 1 GHz and 1.3 GHz • Optimized for front I/O • Hot Swap (Full) PICMG 2.1 compliant • System & Non-system (peripheral) mode • Extensive Software Support • Up to 2 GB DDR SDRAM (200MHz) with ECC • Flash Drive or local 2.5” hard disk • VGA/LCD up to 1600 x 1200 • Two Gigabit Ethernet ports10/100/1000 BaseT front or rear optional ® ® CP9 is a 6U CompactPCI all-in-one CPU board with a low power Intel Pentium M • PICMG 2.16 compliant processor and dual Gigabit Ethernet channels. The CP9 supports full hot swap and is capable of being used in a system or non-system (peripheral) slot. Adhering to the • Two PMC extension slots, PICMG 2.16 dual Ethernet specification, the CP9 supports the 64-bit/66 MHz one 64-bit/133 MHz and one CompactPCI bus. 32-bit/33 MHz The dual slot wide front panel allows to install on the CP9 two PMC modules and a • Ultra ATA/100 onboard, Hard disk or a Flash drive in parallel. This compact all-in-one CPU module is very well second channel rear I/O suited for I/O intensive applications in market segments like automation, industrial • 2x serial I/O with FIFOs control, transportation, and others. RS-232/422/485 interface The CP9 platform is designed to support processors starting with 1 GHz up to • USB 2.0 ports, one front, 1.8 GHz. It offers low power consumption and eliminates the need for on-board fans. four rear The design is ready to accept future higher performance Intel Pentium M processor versions. • IEEE 1284 parallel port The CP9 provides a unique feature set, including up to 2 GB of DDR SDRAM • Watchdog, temperature (200MHz) with ECC, three independent on-board PCI buses, high speed support for sensors the CPCI backplane, two PMC interfaces (64-bit/133MHz and 32-bit/33 MHz). A high • Optional –40 °C / +85 °C level of functional integration (VGA/TFT, USB, serial interfaces, etc.) within a single board and wide front panel gives users the freedom to use the PMC interfaces as • Customer specific, low cost extension for their applications. This combined with a custom specific assembly service assembly versions provides optimized price/performance for a range of OEM applications. The CP9 is • RoHS compliant with version also available in an extended temperature version ranging from -40 °C to +85 °C. 3.x ® ® ® Supported operating systems include Windows XP, VxWorks and Linux . QNX6 and ® LynxOS are on request. CP9 version 3.x is RoHS compliant. Single Board Computers Specifications VGA and LCD – ATI MOBILITY™ RADEON™ CompactPCI – PLX 6254 PCI-to-PCI Bridge CP9 board version 3.x only, RoHS version • PICMG 2.0 R3.0 compliant CPCI local bus standard • 128/256-bit 2D, 3D and multimedia graphics accelerator • 64-bit PCI-to-PCI bridge for up to 8 slots (33 MHz) • Local DDR memory (16 MB or 64 MB) @ 125 MHz to 200 MHz or 5 slots (66 MHz) • 32-bit/33 MHz PCI interface • Supports System and Peripheral Mode • Dual independent CRT controllers to support two • J1+2, 2 mm pin and socket connectors (IEC-1076-4-101) asynchronous simultaneous display paths • RAMDAC (300 MHz to 400 MHz) for analog VGA (1600 x Processor - µFCBGA, Low Power Design 1200) • Scalable processing power with flexible processor design • TDMS transmitter up to 165 MHz (1024 x 768 at 60 Hz); DVI • Intel Pentium M processor: 1.4 GHz to 1.8 GHz • Full support of OpenGL 1.3 (Windows) and xFreeX86 (Linux) • Intel Celeron M processor: 1.0 GHz and 1.3 GHz • Support for DirectX 6.0 to DirectX® 8.1 under Windows • High efficiency on-board switching regulator (DC/DC) • Fanless cooling with heatsink EIDE- ICH4 • Contact factory for latest CPU versions • Ultra ATA/100 sync. DMA mode up to 100 Mbytes/sec • PIO mode 4 and bus master IDE up to 16 Mbytes/sec Chipset – Intel E7501/P64H2/ICH4 • Two devices supported via local EIDE connector and two • 400 MHz system bus to processor devices via rear I/O • PCI burst mode transfers up to 512 MB/s (64-bit/66 MHz) • Two 64-bit wide PCIbusses with 66 MHz Serial I/O - RS232/422/485 • One 32-bit wide PCIbus with 33 MHz • Two async. 16550 compatible full duplex serial channels at rear I/O Cache Level 1 Level 2 • High-speed transfer up to 115.2 kbaud with 16 byte FIFOs Pentium M 90nm 32 KB 2048 KB, full speed • User selectable RS232/422/485 interface Pentium M 130nm 32 KB 1024 KB, full speed • COM1 optional available at front Celeron M 90nm 32 KB 512 KB, full speed Celeron M 130nm 32 KB 512 KB, full speed Parallel Port • Bi-directional, IEEE 1284 compatible enhanced parallel port Memory – DDR 200 (including EPP and ECP) for printer • High-speed registered DDR SDRAM • 72-bit wide with error correction (ECC) USB 2.0 – ICH4 • 512 Mbytes to 2 Gbyte with soldered chips • One USB 2.0 connector at front • Four universal serial bus channels at rear Dual Gigabit Ethernet – Intel 82546GB • Highly integrated Dual Channel Ethernet Controller with General Purpose I/O (software configurable) 64-bit/66 MHz PCI local bus DMA • Eight GPIO (input or output) pins • 64 Kbyte Transmit and Receive FIFO • Interrupt capability (edge, level) • 10/100/1000BaseT auto-negotiation • Versions with front and rear I/O available Keyboard and Mouse • Compliant to PICMG 2.16 • PS/2 compatible Hard Disk or Flash Drive Real-time clock • Internal 2.5” IDE hard disk or 2.5” Flash Drive (for extended • RTC 146818 compatible, on-board Li-battery temperature range and higher shock/vibration immunity) CMOS RAM PMC Extension Slots - IEEE P1386/1386.1 • 242 bytes non-volatile CMOS RAM • One high bandwidth 64-bit/133 MHz PMC and one 32-bit/33 MHz PMC interface EEPROM • Enhancement to processor PMC standard VITA 32-2003 (non- • 512 Kbit serial EEPROMs for non-volatile user data monarch) • Both PMC slots support front panel I/O and rear I/O Floppy • Cardbus adapter available on PMC2 • One channel 3.5“ floppy drive controller VGA and LCD – NVIDIA® GeForce™4 420 Go Watchdog (user programmable) CP9 board version 2.x only • Watchdog 1: 4.8 µs to 76 s, 0.6 s increments • 256-bit 3D and 2D graphics accelerator • Watchdog 2: 1 min to 255 min, 1 min increments • On-chip 32 Mbytes frame buffer (66-190 MHz) • 32-bit/33 MHz PCI interface Timer • Dual CRTC/Simultaneous Dual Display • Integrated in E7501/ICH4 chipset • 350 MHz Palette-DAC for analog VGA (up to 1600 x 1200) • DVI-I interface (PanelLink®) for TFT displays up to 1024 x Temperature Sensors 768, single channel DVI (165 MHz), EDID display PnP • CPU die and heat sink temperature software supported readable from –65 °C to +127 °C • Fully compliant support for OpenGL™ 1.2 for all supported Windows operating systems and Linux Power Requirements LED • Front panel LED System control • +5 V, +3.3V, +12V Required • Hot swap (blue), Status (red / yellow / green) • -12V If required by mounted PMC module Hot-Swap - compliant to PICMG 2.1 Power Consumption - typical operating current • Peripheral mode: Board can be inserted or removed in a • w/o keyboard, hard disk, modules, Ethernet (no link), powered system measured at DOS prompt, no power savings. • System controller mode: Other, non system (peripheral) Processor, Memory 5 V 3.3 V Total Power boards can be removed or added with power on 1.0 GHz, 1 GB 1.0 A 5.9 A 24.5 W 1.3 GHz, 1 GB 2.2 A 5.9 A 30.5 W BIOS Features 1.4 GHz, 2 GB 1.4 A 5.9 A 26.5 W • New AMI BIOS Core 8, in-system programmable Flash ROM 1.6 GHz, 2 GB 2.7 A 5.9 A 33.0 W • CPU, memory and IDE auto-detection/selection • Integrated VGA, and Ethernet BIOS ROM 1.8 GHz, 2 GB 2.5 A 5.9 A 32.0 W • USB Mass Storage support and booting capability (floppy, HDD, CDROM) • w/o keyboard, hard disk, modules, Windows XP, 3D graphics • Password protection, BIOS post, system and video BIOS active. Both Gigabit Ethernet channels linked, CPU running at shadowing instruction mix for maximum power consumption. • Extensive setup with remappable serial/parallel ports • Operation without disk, keyboard and video Processor, Memory 5 V 3.3 V Total Power • Remote BIOS through serial port 1.0 GHz, 1 GB 1.3 A 7.5 A 31.3 W 1.3 GHz, 1 GB 4.6 A 7.5 A 47.8 W Software 1.4 GHz, 2 GB 2.7 A 7.5 A 38.3 W • The following software is supported to the extent listed below. 1.6 GHz, 2 GB 5.4 A 7.5 A 51.8 W OS On Request Available 1.8 GHz, 2 GB 4.8 A 7.5 A 48.8 W WIN XP - √ QNX 6 √ - VxWorks - √ Power Allowances - PMC slot Lynx OS √ - • +5 V, +3.3V: Total power max. 7.5 W Linux - √ • ±12 V: 100mA each Front and Rear I/O (with transition module CTM12) Mechanical – PICMG 2.0 • The pinouts of the transition module connectors (rear I/O) • 6U, 2 slots wide corresponds to standard PC connectors (press-fit cables). • 233 x 160 x 40 mm (including Flash drive) or hard disk Function Front Rear Temperature J3/J4/J5 • Note: For detailed information about the operating temperature 1 DVI-I - √ behavior of the board of any style it is absolutely necessary to 1 VGA √ √ consult the manual. The processor type and speed, altitude, 2 2 Eth 1 √ √ the use or not use of Ethernet and video, ambient conditions 2 2 Eth 2 √ √ and the type of cooling influences the board temperature Keyb+Mouse √ √ range. Reset √ √ • All values under typical conditions without a PMC module LEDs √ √ Operating Storage USB 2.0 1-5 1 2-5 Standard 0 °C to +70 °C –40 °C to +85 °C IDE primary - √ Extended –40 °C to +85 °C –40 °C to +85 °C IDE secondary onboard - Floppy - √ COM 1-2 1 1, 2 Operating Storage LPT - √ Humidity 5 – 95 % @ 40 °C 5 – 95 % @ 40 °C GPIO (8 pins) - √ Altitude 15.000 ft. (4.5 km) 40.000 ft. (12 km) PMC 1 (64-bit 133MHz) √ √ PMC 2 (32-bit 33MHz) √ √ Shock (3 axis, up & down, 5 hits / direction) • Style (C , I , 1 , 3): 12g / 6 ms *1 Rear DVI-I connector for DVI and VGA *2 Either front or rear as an order option Vibration (30 minutes each axis) • Style (C , I , 1 , 3): 2 g rms @ 5 to 100 Hz Styles (Non-RoHS) C I (RoHS) 1 3 MTBF Front Panel yes yes • Calculations are available in accordance with MIL-HDBK-217. Front Stiffener no no Please contact factory. Middle Stiffener no no Wedge Locks no no Safety Parts Soldered yes yes • Designed to meet standard UL1950, CE class A, FCC-A Li-Battery yes yes Extended Temp. no yes Conformal Coating no no Conduction Cooled no no CP9 Block Diagram Pentium M processor DDR SDRAM E7501 withECC (2 GB) SMBus ICH4 EIDE P64H2 USB LPC Super I/O PCI PCI 64-bit 66MHz 64-bit 13 66MHz 3MHz Hot Swap Gigabit PCI/PCI PMC1 PCI 32-bit 33MHz Ethernet 1 Bridge Ethernet 2 VGA PMC2 cPCI 64-bit 66MHz Ordering Information Hardware Accessories CTM12: I/O transition module for 6U backplane (IEEE 1101.11-1998 compliant) SCM184TL00C: 1U 19" chassis with 2 CPCI slots, backplane and power supply SCC784UE05CP9: CP9 starter cage, 19", 7U, 84HP, 5 CPCI slots, fans, HDD and DVD ZKAAPS2SPLIT: Cable for keyboard and mouse on front panel Operating Systems Extensive operating systems support are available (see page 3). Chassis with power supplies, backplanes and drives on request. For detailed information and further options, contact SBS. Corporate Headquarters European Headquarters 7401 Snaproll NE Memminger Str. 14 Albuquerque, NM 87109 D-86159 Augsburg, Germany Tel 505.875.0600 Fax 505.875.0400 Tel +49-821-5034-0 Fax +49-821-5034-119 Email info@sbs.com Email aug-info@sbs.com For additional contact information, please visit our web site at www.sbs.com Specifications subject to change without notice. All trademarks and logos are property of their respective owners. ©2006 SBS Technologies, Inc. 20060627