M C E E T R S T Y I F S I E T D N E T M O E ® 20 years of ScopeMeter Test Tool Innovation Introducing the complete 190 Series II Technical Data New 190 Series II ScopeMeter 500 MHz Oscilloscopes—the first high- performance scopes built for harsh industrial environments Introducing the first high-performance portable oscilloscopes with 2 or 4 independently insulated input channels, an IP51 dust- and dripwater proof rating and a CAT III 1000 V/CAT IV 600 V safety rating. Choose from 500 MHz, 200 MHz, 100 MHz or 60 MHz bandwidth models. Now plant maintenance engineers can take a 2- or 4-channel scope into the harsh world of industrial electronics. 190 Series II—a new generation of Fluke ScopeMeter Oscilloscopes The 190 Series II include these capabilities: • Up to four independent floating isolated inputs, up to 1000 V • Up to 5 GS/s real time sampling (Depending on model and channels used) • Deep memory: 10,000 points per trace waveform capture (scope mode) • CAT III 1000 V/CAT IV 600 V safety rated instrument for industrial ® environments • Up to seven hours of battery operation using BP291 • Isolated USB host port for direct data storage to a USB memory device; USB device port for easy PC communication • Easy access battery door for quick battery swaps in the field • Compact and only 2.2 kg (4.8 lb) ® • Security slot: lock down oscilloscope with Kensington lock while unattended • IP 51 rating, dust- and drip-proof ™ • Connect-and-View triggering for intelligent, automatic triggering on fast, slow and even complex signals • Frequency Spectrum using FFT-analysis • Automatic capture and REPLAY of 100 screens ™ • ScopeRecord Roll mode gives 30,000 points per input channel for low frequency signal analysis ™ • TrendPlot paperless recorder mode with deep memory for long-term automatic measurements • 5,000 count DMM included in the 2-channel models G M A E N E A T M I S Y T O I L 9 A 0 0 U 1 Q Oscilloscope modes 190-062 190-102 190-202 190-502 190-104 190-204 Vertical deflection Number of channels 2 2 2 2 4 4 Bandwidth 60 MHz 100 MHz 200 MHz 500 MHz 100 MHz 200 MHz Rise time 5.8 ns 3.5 ns 1.7 ns 0.7 ns 3.5 ns 1.7 ns Number of scope inputs 2 input channels plus external trigger 4 input channels Channel architecture All inputs fully insulated from each other and from ground Inputs may be activated in any combination Input coupling AC or DC, with ground level indicator Input sensitivity 2 mV/div to 100 V/div, plus variable attenuation Bandwidth limiter User selectable: 20 kHz, 20 MHz or full bandwidth Normal/invert/variable On each input channel, switched separately Input voltage CAT III 1000 V/CAT IV 600 V rated, see General Specifications for further details Vertical resolution 8 bit Accuracy ± (2.1 % of reading + 0.04 x range/div) @ 5 mV/div to 100 V/div Input impedance 1 MΩ ± 1 % // 14 pF ± 2 pF Horizontal Maximum real-time sample 625 MS/s for 1.25 GS/s for 2.5 GS/s (2ch) 5 GS/s (single 1.25 GS/s for 2.5 GS/s (2ch) rate (sampled simultaneously) each channel each channel channel) or 2.5 each channel 1.25 GS/s (4ch) GS/s (on 2ch) Record length Up to 10,000 samples per channel Time base range 10 ns/div 5 ns/div 2 ns/div 1 ns/div. 5 ns/div 2 ns/div to 4 s/div to 4 s/div to 4 s/div to 4 s/div. to 4 s/div to 4 s/div Time base in a 1-2-4-sequence ™ Slower time/division settings using ScopeRecord Roll mode (see ‘Recorder mode’) Maximum record length 10,000 samples per channel in scope mode; ™ 30,000 points per channel in ScopeRecord Roll mode (see ‘Recorder mode’) Timing accuracy ± (0.01 % of reading + 1 pixel) Glitch capture 8 ns peak detect on each channel (using real time sampling and data compression, at any timebase setting) Display and acquisition Display 153 mm (6 in) full-color LCD with LED backlight Display modes Any combination of channels; average on/off; replay Visible screen width 12 divisions horizontally in scope mode Digital persistence modes off/short/medium/long/infinite and envelope mode Waveform mathematics One mathematical operation on any 2 input channels: add/subtract/multiply; X-Y-mode Frequency Spectrum using FFT analysis Acquisition modes Normal, Averaged, Auto, Single Shot, ScopeRecord™ roll, glitch capture, waveform compare with automatic “Pass/Fail testing”; Replay Trigger and delay Source Input A, B or External (via meter input) Input A, B, C or D Modes Automatic Connect-and-View™, free run, single shot, edge, delay, dual slope, video, video line, selectable pulsewidth (channel A only), N-cycle Connect-and-View™ Advanced automatic triggering that recognizes signal patterns, automatically sets up and continuously adjusts triggering, time base and amplitude. Automatically displays stable waveforms of complex and dynamic signals like motor drive and control signals. Can be switched off if preferred. Video triggering (on ch. A) NTSC, PAL, PAL+, SECAM; Includes field 1, field 2 and line select High-res, non-interlaced video Non-interlaced video with line-select, for line frequencies in the range 14 kHz up to 65 kHz Pulse width triggering Pulse width qualified by time (on channel A) Allows for triggering t, =t, ≠ t, where t is selectable in minimum steps of 0.01 div or 50 ns Time delay 1 full screen of pre-trigger view or up to 100 screens (=1,200 divisions) of post-trigger delay Dual slope triggering Triggers on both rising and falling edges alike N-cycle triggering Triggers on N-th occurrence of a trigger event; N to be set in the range 2 to 99 2 Fluke Corporation ScopeMeter 190 Series II 2 Fluke Corporation ScopeMeter 190 Series II Automatic capture of 100 screens When in oscilloscope mode, the instrument ALWAYS memorizes the last 100 screens—no specific user setup required. When an anomaly is seen, the REPLAY button can be pressed to review the full sequence of screen events over and over. Instrument can be set up for triggering on glitches or intermittent anomalies and will operate in “baby-sit” mode capturing 100 specified events Replay Manual or continuous replay. Displays the captured 100 screens as a “live” animation, or under manual control. Each screen has date and time-stamp. Replay storage Two sets of 100 screens each can be saved internally for later recall and analysis. Direct storage of additional sets on external flash memory drive through USB host port. FFT—frequency spectrum analysis Shows frequency content of oscilloscope waveform using Fast Fourier Transform Window Automatic, Hamming, Hanning or None Automatic window Digitally re-samples acquired waveform to get optimum frequency resolution in FFT resultant Vertical scale Linear/Logarithmic (in volts or amps) Frequency axis Frequency range automatically set as a function of timebase range of oscilloscope Waveform compare and pass/fail testing Waveform Compare Provides storage and display of a reference waveform for visual comparison with newly acquired waveforms. Reference is derived from an acquired waveform and can be modified in the oscilloscope Pass/Fail Testing In waveform compare mode, the oscilloscope can be set up to store only matching (“Pass”) or only non-matching (“Fail”) acquired waveforms in the replay memory bank for further analysis Automatic scope measurements V dc, V ac rms, V ac+dc, Vpeak max, Vpeak min, Vpeak to peak, A ac, A dc, A ac+dc, frequency (in Hz), risetime (using cursors), falltime (using cursors), Power Factor (PF), Watts, VA, VA reactive, phase (between any 2 inputs), pulsewidth (pos./neg.), dutycycle (pos./neg.), temperature °C, temperature °F (not for Japan), dBV, dBm into 50 I and 600 I, V ac and V (ac+dc) for measurement on pulsewidth modulated motordrives PWM PWM and frequency inverters, V/Hz ration (190-xx2 only) Advanced power and motor drive V/Hz ratio (190-x02 only), Power Factor (PF), Watts, VA, VA reactive, V ac and V (ac+dc) for PWM PWM functions measurement on pulsewidth modulated motordrives and frequency inverters Advanced functions mA*s (current-over-time, between cursors); V*s (voltage over time, between cursors); W*s (energy, between cursors) Cursor measurements Source On any input waveform or on mathematical resultant waveform (excl. X-Y-mode) Dual horizontal lines Voltage at cursor 1 and at cursor 2, voltage between cursors Dual vertical lines Time between cursors, 1/T between cursors (in Hz), voltage between markers, risetime with markers, falltime with markers; Vrms between cursors, Watts between cursors Single vertical line Min-Max and Average voltage at cursor position; frequency and rms-value of individual frequency component in the FFT Resultant ZOOM Ranges from full record overview to zoom in up to sample level, at any record length ScopeMeter 190 Series II Fluke Corporation 3 Meter modes 190-062 190-102 190-202 190-502 190-104 190-204 Meter inputs Via 4 mm banana inputs, fully isolated from Via BNC scope inputs scope inputs and scope ground Number of readings One at a time Up to 4 simultaneously Maximum resolution 5,000 counts 999 counts Input impedance 1 MΩ ± 1 % // 14 pF ± 2 pF Advanced meter functions Auto/manual ranging, relative measurements (Zero reference), TrendPlot™ recording The specified accuracy is valid over the temperature range 18 °C to 28 °C Add 10 % of specified accuracy for each degree C below 18 °C or above 28 °C Voltage V dc accuracy ± (0.5 % + 5 counts) ± (1.5 % + 5 counts) V ac true rms accuracy ± (1 % + 10 counts) 15 Hz to 60 Hz: ± (1.5 % + 10 counts) ± (2.5 % + 15 counts) 60 Hz to 1 kHz: 60 Hz to 20 kHz: ± (2.5 % + 15 counts) V ac+dc true rms accuracy ± (1 % + 10 counts) 15 Hz to 60 Hz: ± (1.5 % + 10 counts) ± (2.5 % + 15 counts) 60 Hz to 1 kHz: 60 Hz to 20 kHz: ± (2.5 % + 15 counts) Voltmeter ranges 500 mV, 5 V, 50 V, 500 V, 1,000 V Resistance Ranges 500 Ω, 5 kΩ, 50 kΩ, 500 kΩ, 5 MΩ, 30 MΩ — Accuracy ± (0.6 % + 5 counts) — Other meter functions Continuity Beeper on < 50 Ω (± 30 Ω) — Diode test Up to 2.8 V — Current (A) A dc, A ac, A ac+dc using an optional current clamp or shunt Scaling factors: 0.1 mV/A, 1 mV/A to 100 V/A and 400 mV/A Temperature With optional accessories. Scale factors 1 °C/mV or 1 °F/mV 4 Fluke Corporation ScopeMeter 190 Series II Recorder modes 190-062 190-102 190-202 190-502 190-104 190-204 ™ ScopeRecord Roll Mode Dual or multiple input waveform storage mode, using deep memory Source and display Input A, Input B, Dual. Any combination of inputs, All channels sampled simultaneously. up to 4 channels. All channels sampled simultaneously. Bandwidth 20 MHz or 20 kHz, user selectable Memory depth 30,000 data points, each holding min/max pair of information Min/max values Min/max values are created at samples that are measured at high sample rate ensuring capture and display of glitches Recording modes Single sweep, continuous roll, Single sweep, continuous roll, Start-on-Trigger (through external), Start-on-Trigger (through any Stop-on-Trigger (through external) channel), Stop-on-Trigger (through any channel) Stop-on-trigger ScopeRecord mode can be stopped by an individual trigger event, or by an interruption of a repetitive trigger signal, through any input channel (through External on 190-XX2 Series) Horizontal scale Time from start, time of day Zoom Ranges from full record overview to zoom in up to sample level, at any record length Memory Two multiple input ScopeRecord waveforms can be saved internally for later recall and analysis Direct storage on external flash memory drive through USB host port ™ ScopeRecord Roll mode sample rate and recording timespan Time base range 5 ms/div ~ 2 min/div Recorded timespan 6 sec ~ 48 hr Time/division in ‘view all’ mode 0.5 s/div ~ 4 h/div Glitch capture 8 ns Sample rate 125 MS/s Resolution 200 μsec ~ 4.8 sec ™ Trendplot Recording Multiple channel electronic paperless recorder. Graphically plots, displays and stores results of up to four automatic scope measurements or a DMM-reading over time. Source and display Any combination of scope measurements, made on any of the input channels, or DMM reading (2-channel instruments) Memory depth 18,000 points (sets) per measurement. Each recorded sample point contains a minimum, a maximum and an average value, plus a date- and timestamp. Ranges Normal view: 5 s/div to 30 min/div In view-all mode: 5 min/div to 48 hr/div (overview of total record) Recorded time span Up to 22 days, with a resolution of 102 seconds Recording mode Continuous recording, starting at 5 s/div with automatic record compression Measurement speed 3 automatic measurements per second or more Horizontal scale Time from start, time of day Zoom Up to 64x zoom-out for full record overview, up to 10x zoom-in for maximum detail Memory Two multiple input TrendPlot records can be saved internally for later recall and analysis Direct storage on external flash memory drive through USB host port Cursor measurements—all recorder modes Source Any waveform trace in any waveform display mode (Scope, ScopeRecord or TrendPlot) Dual vertical lines Cursors may be used to identify Min, Max or Average value of any datapoint in a record, with time between cursors, time from start or absolute time. ScopeMeter 190 Series II Fluke Corporation 5 General Specifications 190-062 190-102 190-202 190-502 190-104 190-204 Input voltage range Rated maximum floating voltage CAT III 1000 V/CAT IV 600 V (maximum voltage between any contact and earth-ground voltage level) Probe input voltage VPS410 CAT III 1000 V/CAT IV 600 V (Maximum voltage between 10:1 probe tip and reference lead) Probe input voltage VPS510 CAT III 300 V (Maximum voltage between 10:1 probe tip and reference lead) Maximum BNC input voltage CAT IV 300 V (maximum voltage on BNC input directly) Maximum voltage CAT III 1000 V/CAT IV 600 V — on meter input (safety designed banana input connectors) Memory save and recall Memory locations (internal) 30 waveform memories plus 10 recording memories plus 9 screen copy memories (190-XX, 2 channel models); 15 waveforms memories plus 2 recording memories plus 1 screen copy memory (190-XX, 4 channel models) 15 waveform memory locations Stores Scope-trace waveform data (2 or 4 traces each) plus screen-copy plus corresponding setup Two recording memories Each may contain: • a 100 Screen Replay sequence, or • a ScopeRecord Roll-mode recording (2 or 4 traces), or • a TrendPlot recording of up to 4 measurements External data storage • On PC, using FlukeView™ Software, or • Direct storage on external flash memory drive (maximum 2 GB) through USB host port Screencopies • On PC, using FlukeView™ Software, or • Internally (in instrument) which can be copied on to external flash memory drive as .BMP-file, through USB host port Volatility Measurement data is initially stored in RAM, which is maintained by the main battery with a 30 seconds back-up when battery is exchanged When storing data, this is written in non-volatile flash-ROM Real-time clock Provides date and time stamp information for ScopeRecord, for 100 Screen Replay sequences and for TrendPlot recordings Case Design Rugged, shock-proof with integrated protective holster. Handstrap and hangstrap included as standard Kensington lock supported to lock down instrument when left unattended Drip and dust proof IP 51 according to IEC529 Shock and vibration Shock 30 g, vibration (sinusoidal) 3 g according to MIL-PRF-28800F Class 2 Display size 127 mm x 88 mm (153 mm/6.0 in diagonal) LCD Resolution 320 x 240 pixels Contrast and brightness User adjustable, temperature compensated 2 2 Brightness 200 cd/m typ. using power adapter, 90 cd/m typical using battery power Mechanical data Size 265 mm x 190 mm x 70 mm (10.4 in x 7.5 in x 2.8 in) Weight (including battery) 2.1 kg (4.6 lb) 2.2 kg (4.8 lb) Power Line power Mains adapter/battery charger BC190 included, version depending of country Battery power Re-chargeable double capacity Li-Ion battery (included). Battery swappable through easily accessible battery door at the rear of the instrument Battery type (incl.) and capacity BP290; 2400 mAh BP291; 4800 mAh [+opt. battery] [BP291 (4800 mAh) optional] Battery charge indicator Battery has built-in status indicator for use with external charger, next to battery status indicator on instrument screen Battery operating time Up to four hours using BP290 (included), Up to seven hours using BP291 (included) (with backlight low) Up to eight hours using BP291 (optional) Battery charging time 2½ hours using BP290; 5 hours using BP291 Five hours BP291 Battery power saving functions Auto ‘power down’ with adjustable power down time; Auto ‘Display off’ with adjustable power down time; On-screen battery power indicator Safety Compliance EN61010-1-2001, Pollution Degree 2; CAN/CSA C22.2, No. 61010-1-04, with approval; UL61010B; ANSI/ISA-82.02.01 6 Fluke Corporation ScopeMeter 190 Series II 190-062 190-102 190-202 190-502 190-104 190-204 Environmental Operating temperature 0 °C ~ +40 °C; +40 °C ~ +50 °C excl. battery Storage temperature -20 °C ~ +60 °C Humidity +10 °C ~ +30 °C: 95 % RH non-condensing; +30 °C ~ +40 °C: 75 % RH non-condensing; +40 °C ~ +50 °C: 45 % RH non-condensing Maximum operating altitude Up to 2,000 m (6666 ft) for CAT IV 600 V, CAT III 1000 V; up to 3,000 m (10,000 ft) for CAT III 600 V, CAT II 1000 V Maximum storage altitude 12 km (40,000 ft) Electro-Magnetic- EN 61326 (2005-12) for emission and immunity Compatibility (EMC) Interfaces Two USB-ports provided. Ports are fully insulated from instrument’s floating measurement circuitry USB-host port directly connects to external flash memory drive (up to 2 GB) for storage of waveform data, complete datasets in which data and setup information is included, instrument settings and screen copies A mini-USB-B is provided which allows for interconnection to PC for remote control and data transfer under PC-control Probe calibration output Dedicated probe-cal output with reference contact provided, fully insulated from any measurement input channel Warranty Three years (parts and labor) on main instrument, one year on accessories Included accessories Battery charger/mains adapter BC190 Li-Ion battery pack BP290 (2400 mAh) BP291 (4800 mAh) Voltage probe sets. Each set VPS410 (one red, one blue) VPS410 (one red, one grey, one includes ground lead, hook blue, one green) clip, ground spring and probe tip insulation sleeve. Test leads TL175 (one red, one black) with test pins (N/A) Voltage Probes VPS410-x: each set includes: Ground lead, hook clip, ground spring and probe tip insulation sleeve. VPS510-x: each set includes: Ground lead, hook clip, ground spring, probe tip insulation sleeve and BNC-to probe tip adapter. Other Li-Ion battery (BP290 or BP291, see above); Battery charger (BC190); Hangstrap; Handstrip (user selectable for left- or right hand use); Multi language users manuals on CD-ROM; ® FlukeView demo package (with restricted functionality); USB interface cable for PC connectivity. ScopeMeter 190 Series II Fluke Corporation 7 Ordering information Models Fluke 190-502 Color ScopeMeter, 500 MHz, 2 channels plus DMM/Ext.input Fluke 190-502/S Color ScopeMeter, 500 MHz, 2 channels plus DMM/Ext.input, with SCC-290 kit included Fluke 190-204 Color ScopeMeter, 200 MHz, 4 channels Fluke 190-204/S Color ScopeMeter, 200 MHz, 4 channels, with SCC-290 kit included Fluke 190-104 Color ScopeMeter, 100 MHz, 4 channels Fluke 190-104/S Color ScopeMeter, 100 MHz, 4 channels, with SCC-290 kit included Fluke 190-202 Color ScopeMeter, 200 MHz, 2 channels plus DMM/Ext.input Fluke 190-202/S Color ScopeMeter, 200 MHz, 2 channels plus DMM/Ext.input, with SCC-290 kit included Fluke 190-102 Color ScopeMeter, 100 MHz, 2 channels plus DMM/Ext.input Fluke 190-102/S Color ScopeMeter, 100 MHz, 2 channels plus DMM/Ext.input, with SCC-290 kit included Fluke 190-062 Color ScopeMeter, 60 MHz, 2 channels plus DMM/Ext.input Fluke 190-062/S Color ScopeMeter, 60 MHz, 2 channels plus DMM/Ext.input, with SCC-290 kit included Accessories BC190 Mains adapter/battery charger BP290 Li-ion battery pack, 2400 mAh BP291 Li-ion battery pack, 4800 mAh EBC290 External battery charger for BP290 and BP291 (uses BC190 mains adapter) HH290 Hanging Hook for 190 Series II instruments VPS510-R Electronic Voltage Probe set, 10:1, 500 MHz, one set red VPS510-G Electronic Voltage Probe set, 10:1, 500 MHz, one set grey VPS510-B Electronic Voltage Probe set, 10:1, 500 MHz, one set blue VPS510-V Electronic Voltage Probe set, 10:1, 500 MHz, one set green VPS410-R Industrial Voltage Probe set, 10:1, one set red VPS410-G Industrial Voltage Probe set, 10:1, one set grey VPS410-B Industrial Voltage Probe set, 10:1, one set blue VPS410-V Industrial Voltage Probe set, 10:1, one set green VPS420-R High working voltage ruggedized probe set, 100:1, 150 MHz (bicolored, red/black) SW90W FlukeView ScopeMeter Software package (full version) C290 Hard shell protective carrying case for 190 Series II SCC290 FlukeView ScopeMeter Software package (full version) and C290 Carrying Case kit for 190-series II TL175 TwistGuard™ safety designed Test Leads set (1 red, 1 black) TRM50 BNC Feedthrough 50 I terminator (set of 2 pieces, black) AS400 Probe Accessory Extension Set for VPS400-series probes RS400 Probe Accessory Replacement Set for VPS400-series probes RS500 Probe Accessory Replacement Set for VPS500-series probes Fluke. The Most Trusted Tools in the World. Fluke Corporation PO Box 9090, Everett, WA 98206 U.S.A. Fluke Europe B.V. PO Box 1186, 5602 BD Eindhoven, The Netherlands For more information call: In the U.S.A. (800) 443-5853 or Fax (425) 446-5116 In Europe/M-East/Africa +31 (0) 40 2675 200 or Fax +31 (0) 40 2675 222 In Canada (800)-36-FLUKE or Fax (905) 890-6866 From other countries +1 (425) 446-5500 or Fax +1 (425) 446-5116 Web access: http://www.fluke.com ©2012 Fluke Corporation. Specifications subject to change without notice. Printed in U.S.A. 8/2012 3801685C_EN Pub_ID: 11781-eng Modification of this document is not permitted without written permission from Fluke Corporation. 8 Fluke Corporation ScopeMeter 190 Series II