40 Series - Miniature PCB/Plug-in relays 8 - 10 - 16 A Features 40.31 40.51 40.52 1 & 2 Pole relay range 40.31 - 1 Pole 10 A (3.5 mm pin pitch) 40.51 - 1 Pole 10 A (5 mm pin pitch) 40.52 - 2 Pole 8 A (5 mm pin pitch) PCB mount - direct or via PCB socket 35 mm rail mount - via screw and screwless sockets DC coils (standard or sensitive) & AC coils Cadmium Free contact material 3.5 mm contact pin pitch5 mm contact pin pitch5 mm contact pin pitch 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts1 Pole 10 A1 Pole 10 A2 Pole 8 A UL Listing (certain relay/socket combinations)PCB or 95 series socketsPCB or 95 series socketsPCB or 95 series sockets Flux proof: RT II standard, (RT III option) 95 series sockets Coil EMC suppression Timer accessories 86 series FOR UL HORSEPOWER AND PILOT DUTY RATINGS Copper side view Copper side view Copper side view SEE “General technical information” page V Contact specification Contact configuration 1 CO (SPDT) 1 CO (SPDT) 2 CO (DPDT) Rated current/Maximum peak current A 10/20 10/20 8/15 Rated voltage/Maximum switching voltage V AC 250/400 250/400 250/400 Rated load AC1 VA 2,500 2,500 2,000 Rated load AC15 (230 V AC) VA 500 500 400 Single phase motor rating (230 V AC) kW 0.37 0.37 0.3 Breaking capacity DC1: 30/110/220 V A 10/0.3/0.12 10/0.3/0.12 8/0.3/0.12 Minimum switching load mW (V/mA) 300 (5/5) 300 (5/5) 300 (5/5) Standard contact material AgNi AgNi AgNi Coil specification Nominal voltage (U ) V AC (50/60 Hz) 6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 N V DC 5 - 6 - 7 - 9 - 12 - 14 - 18 - 21 - 24 - 28 - 36 - 48 - 60 - 90 - 110 - 125 Rated power AC/DC/sens. DC VA (50 Hz)/W/W 1.2/0.65/0.5 1.2/0.65/0.5 1.2/0.65/0.5 Operating range AC (0.8…1.1)U (0.8…1.1)U (0.8…1.1)U N N N DC/sens. DC (0.73…1.5)U /(0.73…1.75)U (0.73…1.5)U /(0.73…1.75)U (0.73…1.5)U /(0.73…1.75)U N N N N N N Holding voltage AC/DC 0.8 U /0.4 U 0.8 U /0.4 U 0.8 U /0.4 U N N N N N N Must drop-out voltage AC/DC 0.2 U /0.1 U 0.2 U /0.1 U 0.2 U /0.1 U N N N N N N Technical data 6 6 6 6 6 6 Mechanical life AC/DC cycles 10 · 10 /20 · 10 10 · 10 /20 · 10 10 · 10 /20 · 10 3 3 3 Electrical life at rated load AC1 cycles 200 · 10 200 · 10 100 · 10 Operate/release time ms 7/3 - (12/4 sensitive) 7/3 - (12/4 sensitive) 7/3 - (12/4 sensitive) Insulation between coil and contacts (1.2/50 µs) kV 6 (8 mm) 6 (8 mm) 6 (8 mm) Dielectric strength between open contacts V AC 1,000 1,000 1,000 Ambient temperature range °C –40…+85 –40…+85 –40…+85 Environmental protection RT II** RT II** RT II** Approvals (according to type) 1 ** See general technical information “Guidelines for automatic flow solder processes” page II . 40 Series - Miniature PCB/Plug-in relays 8 - 10 - 16 A Features 40.61 40.xx.6 40.61 - 1 Pole 16 A (5 mm pin pitch) 40.xx.6 - Bistable versions of the 40.31, 40.51, 40.52 & 40.61 relays PCB mount - direct or via PCB socket 35 mm rail mount - via screw and screwless sockets DC coils & AC coils Cadmium Free option available 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts5 mm contact pin pitchBistable (single coil) versions UL Listing (certain 40.61 relay/socket combinations)1 Pole 16 A of 40.31/51/52/61 PCB or 95 series socketsPCB or 95 series socketsFlux proof: RT II standard, (RT III option) 95 series sockets Coil EMC suppression Timer accessories 86 series Bistable version (1 coil) types: 40.31.6... 40.51.6... 40.52.6... 40.61.6... For wiring diagrams see page 8 FOR UL HORSEPOWER AND PILOT DUTY RATINGS Copper side view SEE “General technical information” page V Contact specification Contact configuration 1 CO (SPDT) Rated current/Maximum peak current A 16/30* * With the AgSnO material 2 the maximum peak current is Rated voltage/Maximum switching voltage V AC 250/400 See relays 120 A - 5 ms on normally Rated load AC1 VA 4,000 40.31 open contact. Rated load AC15 (230 V AC) VA 750 40.51 Single phase motor rating (230 V AC) kW 0.55 40.52 Breaking capacity DC1: 30/110/220 V A 16/0.3/0.12 40.61 Minimum switching load mW (V/mA) 500 (10/5) Standard contact material AgCdO Coil specification Nominal voltage (U ) V AC (50/60 Hz) 6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 5 - 6 - 12 - 24 - 48 - 110 N V DC ***See table 5 - 6 - 12 - 24 - 48 - 110 *** Nominal voltage (U ): N 5 - 6 - 7 - 9 - 12 - 14 - 18 - 21 - Rated power AC/DC/sens. DC VA (50 Hz)/W/W 1.2/0.65/0.5 1.0/1.0/— 24 - 28 - 36 - 48 - 60 - 90 - Operating range AC (0.8…1.1)U (0.8…1.1)U N N 110 - 125 V DC DC/sens. DC (0.73…1.5)U /(0.8…1.5)U (0.8…1.1)U /— N N N Holding voltage AC/DC 0.8 U /0.4 U — N N Must drop-out voltage AC/DC 0.2 U /0.1 U — N N Technical data 6 6 Mechanical life AC/DC cycles 10 · 10 /20 · 10 See relays 3 Electrical life at rated load AC1 cycles 100 · 10 40.31 Operate/release time ms 7/3 - (12/4 sensitive) 40.51 Insulation between coil and contacts (1.2/50 µs) kV 6 (8 mm) 40.52 Dielectric strength between open contacts V AC 1,000 40.61 Ambient temperature range °C –40…+85 Min. impulse duration Environmental protection RT II** ≥ 20 ms Approvals (according to type) 2 ** See general technical information “Guidelines for automatic flow solder processes” page II. 40 Series - Miniature PCB/Plug-in relays 8 - 10 - 16 A Features 40.11 40.11-2016 40.41 1 Pole relay range 40.11 - 1 Pole 10 A (Flat pack) 40.11-2016 - 1 Pole 16 A (Flat pack) 40.41 - 1 Pole 10 A (Vertical) PCB mount - direct or via PCB socket (40.41 version) DC coils Cadmium Free option available 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts 1 Pole 10 A40.41 - NO version available1 Pole 10 A1 Pole 16 A Flat packFlat packVertical PCB mountPCB mountPCB or 95 series socket 40.11 40.41 FOR UL HORSEPOWER AND PILOT DUTY RATINGS Copper side view Copper side view Copper side view SEE “General technical information” page V Contact specification Contact configuration 1 CO (SPDT) 1 CO (SPDT) 1 CO (SPDT) Rated current/Maximum peak current A 10/20 16/30 10/20 Rated voltage/Maximum switching voltage V AC 250/400 250/400 250/400 Rated load AC1 VA 2,500 4,000 2,500 Rated load AC15 (230 V AC) VA 500 750 500 Single phase motor rating (230 V AC) kW 0.37 0.55 0.37 Breaking capacity DC1: 30/110/220 V A 10/0.3/0.12 16/0.3/0.12 10/0.3/0.12 Minimum switching load mW (V/mA) 300 (5/5) 500 (10/5) 300 (5/5) Standard contact material AgCdO AgCdO AgCdO Coil specification Nominal voltage (U ) V AC (50/60 Hz) ——— N V DC 6 - 12 - 24 - 48 - 60 6 - 12 - 24 - 48 6 - 12 - 24 - 48 - 60 Rated power AC/DC/sens. DC VA (50 Hz)/W/W —/—/0.5 —/—/0.5 —/—/0.5 Operating range AC ——— DC/sens. DC —/(0.73…1.75)U —/(0.73…1.5)U —/(0.73…1.75)U N N N Holding voltage AC/DC —/0.4 U —/0.4 U —/0.4 U N N N Must drop-out voltage AC/DC —/0.1 U —/0.1 U —/0.1 U N N N Technical data 6 6 6 Mechanical life AC/DC cycles —/20 · 10 —/20 · 10 —/20 · 10 3 3 3 Electrical life at rated load AC1 cycles 200 · 10 50 · 10 200 · 10 Operate/release time ms 12/4 12/4 12/4 Insulation between coil and contacts (1.2/50 µs) kV 6 (8 mm) 6 (8 mm) 6 (8 mm) Dielectric strength between open contacts V AC 1,000 1,000 1,000 Ambient temperature range °C –40…+70 –40…+70 –40…+70 Environmental protection RT I RT I RT I Approvals (according to type) 3 40 Series - Miniature PCB/Plug-in relays 8 - 10 - 16 A Ordering information Example: 40 series PCB relay, 2 CO (DPDT), 230 V AC coil. AB C D 40.. 5 2 8.230. 0 0 0 0 Series A: Contact material D: Special versions 0 = Standard AgNi 0 = Standard Type for 40.31/51/52, 1 = Wash tight (RT III) 1 = PCB - 3.5 mm pinning, flat AgCdO for 40.61 3 = High temperature (+ 125 °C) wash tight 3 = PCB - 3.5 mm pinning 2 = AgCdO (standard 4 = PCB - 3.5 mm pinning C: Options for 40.11/41) 5 = PCB - 5 mm pinning 0 = None 4 = AgSnO 2 6 = PCB - 5 mm pinning 16 = With rated current 16 A (for 40.11) 5 = AgNi + Au (5 µm) No. of poles B: Contact circuit 1 = 1 pole 0 = CO (nPDT) for: 40.11, 10 A/16 A 3 = NO (nPST) 40.31, 10 A 40.41, 10 A 40.51, 10 A 40.61, 16 A 2 = 2 pole for: 40.52, 8 A Coil version 6 = AC/DC bistable 7 = Sensitive DC 8 = AC (50/60 Hz) 9 = DC Coil voltage Selecting features and options: only combinations in the same row are possible. See coil specifications Preferred selections for best availability are shown in bold. Type Coil version A B C D 40.11 sensitive DC 2 - 4 00 0 40.11 sensitive DC 2 - 4 0 16 / 40.41 sensitive DC 0 - 20 - 3 00 40.31/51 AC-sens. DC 0 - 2 - 5 0 - 3 00 - 1 40.31/51 DC 0 - 2 - 5 0 - 3 00 - 1 - 3 40.52 AC-sens. DC 0 - 2 - 5 0 - 3 00 - 1 40.52 DC 0 - 2 - 5 0 - 3 00 - 1 - 3 40.61 AC-sens. DC 0 - 4 0 - 3 00 - 1 40.61 DC 0 - 4 0 - 3 00 - 1 - 3 40.31/51/ bistable 00 0 0 52/61 4 40 Series - Miniature PCB/Plug-in relays 8 - 10 - 16 A Technical data Insulation according to EN 61810-1 1 pole 2 pole Nominal voltage of supply system V AC 230/400 230/400 Rated insulation voltage V AC 250 400 250 400 Pollution degree 3 2 3 2 Insulation between coil and contact set Type of insulation Reinforced (8 mm) Reinforced (8 mm) Overvoltage category III III Rated impulse voltage kV (1.2/50 µs) 6 6 Dielectric strength V AC 4,000 4,000 Insulation between adjacent contacts Type of insulation — Basic Overvoltage category — II Rated impulse voltage kV (1.2/50 µs) — 2.5 Dielectric strength V AC — 2,000 Insulation between open contacts Type of disconnection Micro-disconnection Micro-disconnection Dielectric strength V AC/kV (1.2/50 µs) 1,000/1.5 1,000/1.5 Conducted disturbance immunity Burst (5...50)ns, 5 kHz, on A1 - A2 EN 61000-4-4 level 4 (4 kV) Surge (1.2/50 µs) on A1 - A2 (differential mode) EN 61000-4-5 level 3 (2 kV) Other data Bounce time: NO/NC ms 2/5 Vibration resistance (5…55)Hz: NO/NC g 10/4 (1 changeover) 15/3 (2 changeover) Shock resistance g 13 Power lost to the environment without contact current W 0.6 with rated current W 1.2 (40.11/31/41/51) 2 (40.61/52/40.11-2016) Recommended distance between relays mounted on PCB mm ≥ 5 5 40 Series - Miniature PCB/Plug-in relays 8 - 10 - 16 A Contact specification F 40 - Electrical life (AC) v contact current F 40 - Electrical life (AC) v contact current Types 40.31/51/61 Type 40.52 Resistive load - cosϕ = 1 Resistive load - cosϕ = 1 Inductive load - cosϕ = 0.4 Inductive load - cosϕ = 0.4 limit for 40.31/51 F 40 - Electrical life (AC) v contact current H 40 - Maximum DC1 breaking capacity Types 40.11/41 40.61 current limit 40.11/31/41/51 current limit 40.52 current limit Resistive load - cosϕ = 1 Inductive load - cosϕ = 0.4 40.52 - 2 contacts in series single contact limit for version 10 A DC voltage (V) When switching a resistive load (DC1) having voltage and current 3 values under the curve, an electrical life of ≥ 100·10 can be expected. In the case of DC13 loads, the connection of a diode in parallel with the load will permit a similar electrical life as for a DC1 load. Note: the release time for the load will be increased. 6 Cycles Cycles Cycles DC breaking current (A) 40 Series - Miniature PCB/Plug-in relays 8 - 10 - 16 A Coil specifications DC coil data - 0.65 W standard (types 40.31/51/52/61) DC coil data - 0.5 W sensitive (types 40.31/51/52/61) Nominal Coil Operating range Resistance Rated coil Nominal Coil Operating range Resistance Rated coil voltage code consumption voltage code consumption U U U R I at U U U*U ** R I at U N min max N N min max N VVV Ω mA VVV Ω mA 5 9.005 3.65 7.5 38 130 5 7.005 3.7 8.8 50 100 6 9.006 4.4 9 55 109 6 7.006 4.4 10.5 75 80 7 9.007 5.1 10.5 75 94 7 7.007 5.1 12.2 100 70 9 9.009 6.6 13.5 125 72 9 7.009 6.6 15.8 160 56 12 9.012 8.8 18 220 55 12 7.012 8.8 21 300 40 14 9.014 10.2 21 300 47 14 7.014 10.2 24.5 400 35 18 9.018 13.1 27 500 36 18 7.018 13.2 31.5 650 27.7 21 9.021 15.3 31.5 700 30 21 7.021 15.4 36.9 900 23.4 24 9.024 17.5 36 900 27 24 7.024 17.5 42 1,200 20 28 9.028 20.5 42 1,200 23 28 7.028 20.5 49 1,600 17.5 36 9.036 26.3 54 2,000 18 36 7.036 26.3 63 2,600 13.8 48 9.048 35 72 3,500 14 48 7.048 35 84 4,800 10 60 9.060 43.8 90 5,500 11 60 7.060 43.8 105 7,200 8.4 90 9.090 65.7 135 12,500 7.2 90 7.090 65.7 157 16,200 5.6 110 9.110 80.3 165 18,000 6.2 110 7.110 80.3 192 23,500 4.7 125 9.125 91.2 188 23,500 5.3 125 7.125 91.2 219 32,000 3.9 *U = 0.8 U for 40.61 **U = 1.5 U for 40.61 min N max N DC coil data - 0.5 W sensitive (types 40.11/41) Nominal Coil Operating range Resistance Rated coil voltage code consumption U U U R I at U N min max* N VVV Ω mA 6 7.006 4.4 10.5 75 80 12 7.012 8.8 21 300 40 24 7.024 17.5 42 1,200 20 48 7.048 35 84 4,600 10.4 60 7.060 43.8 105 7,200 8.3 *U = 1.5 U for 40.11-2016 max N AC coil data (types 40.31/51/52/61) AC/DC coil data - bistable (types 40.31/51/52/61) Nominal Coil Operating range Resistance Rated coil Nominal Coil Operating range Resistance Rated coil DC: Release voltage code consumption voltage code consumption resistance** U U U R I at U (50Hz) U U U R I at U R N min max N N min max N DC VVV Ω mA VVV Ω mA Ω 6 8.006 4.8 6.6 21 168 5 6.005 4 5.5 23 215 37 12 8.012 9.6 13.2 80 90 6 6.006 4.8 6.6 33 165 62 24 8.024 19.2 26.4 320 45 12 6.012 9.6 13.2 130 83 220 48 8.048 38.4 52.8 1,350 21 24 6.024 19.2 26.4 520 40 910 60 8.060 48 66 2,100 16.8 48 6.048 38.4 52.8 2,100 21 3,600 110 8.110 88 121 6,900 9.4 110 6.110 88 121 11,000 10 16,500 120 8.120 96 132 9,000 8.4 ** R = Resistance in DC, R = 1.3 x R 1W DC AC DC 230 8.230 184 253 28,000 5 240 8.240 192 264 31,500 4.1 7 40 Series - Miniature PCB/Plug-in relays 8 - 10 - 16 A Coil specifications R 40 - DC coil operating range v ambient temperature R 40 - DC coil operating range v ambient temperature Standard coil Sensitive coil, types 40.31/51/52/61 R 40 - DC coil operating range v ambient temperature R 40 - AC coil operating range v ambient temperature Sensitive coil, types 40.11/41 1 - Max. permitted coil voltage. 1 - Max. permitted coil voltage. 2 - Min. pick-up voltage with coil at ambient temperature. 2 - Min. pick-up voltage with coil at ambient temperature. Wiring diagram for 40 series bistable coil version AC Operation DC Operation On momentary closure of the SET switch the relay is magnetised through On momentary closure of the SET switch the relay is magnetised and the the diode and the relay contacts transfer to the set position and remain in relay contacts transfer to the set position and remain in this position. this position. On momentary closure of the RESET switch the relay is demagnetised On momentary closure of the RESET switch the relay is demagnetised through limiting resistor (R ) and the contacts return to the reset position. DC through limiting resistor (R ) and the contacts return to the reset position. AC Notes: The minimum SET or RESET impulse time is 20 ms. The maximum time can be continuous. In practice, always ensure that the SET and RESET contacts cannot be operated simultaneously. 8