® Datasheet Dialogic TX 4000 Series SS7 Boards ® The Dialogic TX 4000 Series SS7 Boards offer a range of form factor, throughput capacity, and signaling protocol support ® ™ with Dialogic NaturalAccess Software. The TX 4000 Series architecture combines TDM connectivity and transport with the SS7 protocol layers required for a higher-level application interface. Products Discussed in This Datasheet: ® •  Dialogic   TX 4000 PCI SS7 Network Interface Board ® •  Dialogic   TX 4000/20 PCI SS7 Network Interface Board ® •  Dialogic   TX 4000C CompactPCI SS7 Network Interface Board ® •  Dialogic   TX 4000/20C CompactPCI SS7 Network Interface Board Large Logo Features Benefits Hardware and protocol software are combined — MTP, Minimizes host loading and simplifies integration ISUP, TUP, and BICC ® ™ ® Uses Dialogic NaturalAccess Software Eases integration with Dialogic media boards that support NaturalAccess Software High-impedance (HiZ) connectivity Enables passive signaling traffic monitoring H.100/H.110 bus interfaces Allows integration with other H.100/H.110 products, including a combination of data communications and voice streams over the same physical trunk Downloadable control software Reduces host overhead and uses host processing time efficiently when running applications 10/100Base-T Ethernet interface Allows two separate boards to share a single point code Medium Logo Two system design options — node redundancy or board Helps enable high availability in one or multiple redundancy synchronized systems Onboard temperature sensor Promotes safe operation by first sending an alarm and then shutting down the TX 4000 board if temperature exceeds safe operating limits To find out more about Dialogic call 800.755.4444 or visit us at: www.dialogic.com Small Logo ® Datasheet Dialogic TX 4000 Series SS7 Boards Onboard Protocol Execution The TX 4000 Series boards are available with MTP or MTP, ISUP, TUP, and BICC layers of the SS7 stack running on board processors. Multiple Network Interfaces The digital trunk interfaces of the TX 4000 Series are software-configurable to support either T1 or E1 connections. The TX 4000 and TX 4000/20 have 4 trunks, and the TX 4000C and TX 4000/20C have 8 trunks. The TX 4000C and TX 4000/20C include either a rear transition card with both digital trunk and Ethernet connectors or a rear transition card with digital trunk connectors with Ethernet connected via the CompactPCI PICMG 2.16 bus. For network interfaces, all channels from the primary rate digital trunk interfaces can either be terminated locally on the TX 4000 Series or switched onto the H.100/H.110 bus for processing by other H.100/H.110-compliant products. H.100/H.110 Ensures Open Architecture and Vendor Independence H.100/H.110 bus and switching provides flexibility, openness, and vendor independence, with access to other resources such as voice and call processing, modem pools, and speech recognition engines. The TX 4000 and TX 4000/20 provide an H.100 bus interface, while the TX 4000C and TX 4000/20C offer an H.110 bus interface. Redundancy When deploying two boards from the TX 4000 Series in a redundant configuration, one onboard Ethernet interface is required. The interface supports a dedicated point-to-point link to provide extremely fast data transfer between the two boards. This approach avoids the need to transfer lower-level data over the host computer’s bus and can significantly improve SS7 signaling performance. Redundancy protects against signaling link, board, and node failure. A typical redundant configuration has two boards — one primary and one backup — under a single point code, with active links interfacing to each board. Link-level redundancy is managed automatically at the MTP level. Higher-level check-pointing can be implemented by the application for total redundancy. Configuration The TX 4000 Series is available in both PCI and CompactPCI form factors. The TX 4000 Series can run the entire SS7 protocol stack (MTP, ISUP, TUP, and BICC) onboard. Each product requires the appropriate SS7 software runtime license and comes with ® drivers to support Windows , Solaris, or Linux operating systems. 2 ® Datasheet Dialogic TX 4000 Series SS7 Boards Technical Specifications ® Dialogic TX 4000 Series SS7 Boards — Product-Dependent Features Feature TX 4000 TX 4000/20 TX 4000C TX 4000/20C Form factor PCI PCI CompactPCI CompactPCI E1 / T1 interfaces 4 4 8 8 SS7 channelized links (64/56 kbps) 4, 16, 32 4, 16 4, 16, 32 4, 16 HSL Q703 4 4 4 4 Performance Calls per second 1,100 150 1,100 150 Transactions per second 2,400 320 2,400 320 TDM bus full-duplex connections 128 H.100 256 H.110 Host interface Electrical: PCI bus Rev. 2.2 Mechanical: PICMG 2.0, Rev 2.1; PICMG 2.16 Mechanical: PCI bus Rev. 2.1 Bus speed: 33/66 MHz Form factor: Full height, full length Hot Swap: PICMG 2.1, Rev 1.0 PCI universal expansion board: Keyed for 5.0 V and 3.3 V signaling environment Bus speed: 33/66 MHz Power requirements 6.5 A @ 3.3 V, 0.5 A @ 5 V, 0.1 A @ 12 V 6 A @ 3.3 V, 1.25 A @ 5 V, 10 mA @ 12 V All Products TDM bus 1,024 local connections Switchable access to any of 4,096 bi-directional timeslots for up to 2,048 full-duplex calls Monitoring HiZ Environment Operating temperature: 0 ºC to +50 ºC @ 200 LFM Storage temperature: -20 ºC to +70 ºC Relative humidity: 5% to 80%, non-condensing Available onboard protocols SS7: MTP2, MTP3, ISUP, TUP, BICC ® Operating system support Windows , Linux, and Solaris: Details at www.dialogic.com/systemreleases 3 ® Datasheet Dialogic TX 4000 Series SS7 Boards Technical Specifications (continued) Telephony interface DSX-1 Interface: Complete interface to T1 trunks (ANSI T1.102, T1.403) Framing: D4, ESF Line code: AMI, B8ZS Zero bits: Selectable B8ZS, jammed bit (ZCS) or no zero code suppression Alarm signal capabilities: - Loss of Signaling Multiframe Alignment and Loss of CRC Multiframe Alignment (red) - Remote Alarm and Remote Multiframe Alarm (yellow) - Alarm Indication Signal (AIS) (blue) Counts: Bipolar violation, F(t) error, and CRC error Loopback: Per-channel and overall under software control Telephony interface CEPT E1 G.703/G.704 Interface: Full featured G.703 2048 kbps trunk interface Framing: CEPT G.704 HDLC/LAPD for generating/terminating a data link Line code: HDB3 or AMI (in zero code suppression) Zero bits: Selectable B8ZS, jammed bit (ZCS) or no zero code suppression Alarm signal capabilities: - Loss of Frame Alignment (OOF), Loss of Signaling Multiframe Alignment and Loss of CRC Multiframe Alignment (red) - Remote Alarm, and Remote Multiframe Alarm (yellow) - Alarm Indication Signal (AIS) (blue) Counts: Bit error rate, CRC errors slips, line code violations, far-end block errors Loopback: Per-channel and across channels under software control Standards T1 interfaces Digital multiplexer requirements and objectives: AT&T Pub. 43802, July 82 Service description and interface specifications: AT&T TR 62411, ACCUNET T1.5 Carrier to customer installation DS1 metallic interface: ANSI T1E1/88-001R1, February 88 ANSI T1 Standard for ISDN Primary Rate Interface: T1E1.4/8868 (proposed text) April 88 Primary Rate User-network Interface Layer 1 Specification: ITU-T I.431, June 88 E1 interfaces G.703: Physical/electrical characteristics of hierarchical digital network G.704: Synchronous frame structures used at primary and secondary hierarchical levels G.706: Frame alignment and cyclic redundancy check procedures G.732: Characteristics of primary PCM multiplex equipment G.823: Control of jitter and wander within digital networks based on 2,048 kbps hierarchy ETSI: ETS 300-418, 300-246, 300-247, 300-248 Primary Rate User-network Interface Layer 1 Specification: ITU-T I.431, June 88 4 ® Datasheet Dialogic TX 4000 Series SS7 Boards Technical Specifications (continued) Regulatory Compliance Safety CB Certificate to IEC 60950-1, EN60950-1 UL 60950-1, CSA Certified in File 200040 CAN/CSA-C22.2 No 60950-1, CSA Certified in File 200040 EMC EN55022, CISPR 22, all Class B FCC 47 CFR Part 15, Subpart B, ICES-003, all Class A EN55024 Telecommunications TBR12, TBR13 TIA-968-A, TIA-968-A-1, TIA-968-A-2, TIA-968-A-3, TIA-968-A-4, ACTA Product-Labeling number; US: EMCXDNANTX4000 CS-03 Registered number; IC: 776B-TX4000 Hazardous substances RoHS compliance information at www.dialogic.com/rohs Country-specific approvals See the global product approvals database at www.dialogic.com/declarations Reliability/Warranty Estimated MTBF TX 4000, TX 4020: 4.24 years TX 4000C, TX 4020C: 15.36 years Warranty Warranty information at www.dialogic.com/warranties 5 ® Datasheet Dialogic TX 4000 Series SS7 Boards Ordering Information ® Dialogic TX 4000 Series SS7 Boards and software are sold as boards supporting specific numbers of SS7 links that include basic (MTP) or complete software (full stack) modules. There are also products for upgrading the number of SS7 links supported. ® Dialogic TX Series Product Order Code Description TX 4000 PCI 82166 TX 4000 - 4 links/MTP (2 RJ-45s) 82167 TX 4000 - 16 links/MTP (2 RJ-45s) 82168 TX 4000 - 32 links/MTP (2 RJ-45s) 82169 TX 4000 - 4 links/full stack (2 RJ-45s) 82170 TX 4000 - 16 links/full stack (2 RJ-45s) 82171 TX 4000 - 32 links/full stack (2 RJ-45s) TX 4000C cPCI with Rear Ethernet I/O 82182 TX 4000C - 4 links/2L/MTP (1 RJ-21) 82183 TX 4000C - 16 links/2L/MTP (1 RJ-21) 82184 TX 4000C - 32 links/2L/MTP (1 RJ-21) 82185 TX 4000C - 4 links/2L/full stack (1 RJ-21) 82186 TX 4000C - 16 links/2L/full stack (1 RJ-21) 82187 TX 4000C - 32 links/2L/full stack (1 RJ-21) TX 4000C PICMG 2.16 cPCI 82176 TX 4000C - 4 links/2.16/MTP (1 RJ-21) 82177 TX 4000C - 16 links/2.16/MTP (1 RJ-21) 82178 TX 4000C - 32 links/2.16/MTP (1 RJ-21) 82179 TX 4000C - 4 links/2.16/full stack (1 RJ-21) 82180 TX 4000C - 16 links/2.16/full stack (1 RJ-21) 82181 TX 4000C - 32 links/2.16/full stack (1 RJ-21) TX 4000/20 PCI 82214 TX 4000/20 - 4 links/MTP (2 RJ-45s) 82215 TX 4000/20 - 16 links/MTP (2 RJ-45s) 82216 TX 4000/20 - 4 links/full stack (2 RJ-45s) 82217 TX 4000/20 - 16 links/full stack (2 RJ-45s) TX 4000/20C cPCI with Rear Ethernet I/O 82222 TX 4000/20C - 4 links/2L/MTP (1 RJ-21) 82223 TX 4000/20C - 16 links/2L/MTP (1 RJ-21) 82224 TX 4000/20C - 4 links/2L/full stack (1 RJ-21) 82225 TX 4000/20C - 16 links/2L/full stack (1 RJ-21) 6 ® Datasheet Dialogic TX 4000 Series SS7 Boards Ordering Information (continued) ® Dialogic TX Series Product Order Code Description TX 4000/20C PICMG 2.16 cPCI 82218 TX 4000/20C - 4 links/2.16/MTP (1 RJ-21) 82219 TX 4000/20C - 16 links/2.16/MTP (1 RJ-21) 82220 TX 4000/20C - 4 links/2.16/full stack (1 RJ-21) 82221 TX 4000/20C - 16 links/2.16/full stack (1 RJ-21) Upgrade Licenses 82172 TX 4000 | 4000C - 4 links to 16 links license upgrade 82173 TX 4000 | 4000C - 4 links to 32 links license upgrade 82174 TX 4000 | 4000C - 16 links to 32 links license upgrade 82175 TX 4000 | 4000C - MTP to full stack software license upgrade 82087 TX 4000/20 | 4000/20C - 4 links to 16 links license upgrade 82259 TX 4000/20 | 4000/20C - MTP to full stack software license upgrade Digital Trunk Connector Cables 83233 Cable, RJ-45 male-to-male, 3' (91cm), ISDN Japan 83230 Cable, RJ-45 to 2X RJ-48C, 120-ohm, 4" (10cm) 83232 Cable, RJ-45 to (2) E-75-ohm BNC pairs, 9"(23), shielded, RoHS Cables for TX 4000C CompactPCI Boards 83225 Cable, RJ-21M-180/RJ-21M-180, 6' (1.8m), shielded, RoHS 83228 Cable, RJ-21M-180/ RJ-21M-RA, 6' (1.8m), shielded, RoHS TX 4000C SEP Panel 83252 SEP – 2X (NMS RJ-21 to (8) RJ-48C interface), 1U 7 Large Logo Medium Logo Small Logo www.dialogic.com Dialogic Corporation 9800 Cavendish Blvd., 5th floor Montreal, Quebec CANADA H4M 2V9 INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH PRODUCTS OF THE DIALOGIC CORPORATION (“DIALOGIC”). NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU AND DIALOGIC, DIALOGIC ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY. Dialogic products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications. Dialogic and NaturalAccess are trademarks or registered trademarks of Dialogic Corporation or its subsidiaries. Dialogic’s trademarks may be used publicly only with permission from Dialogic. Such permission may only be granted by Dialogic’s legal department at the address listed above. Any authorized use of Dialogic’s trademarks will be subject to full respect of the trademark guidelines published by Dialogic from time to time, and any use of Dialogic’s trademarks requires proper acknowledgement. Windows is a registered trademark of Microsoft Corporation in the United States and/or other countries. Other names of actual companies and products mentioned herein are the trademarks of their respective owners. None of the information provided in this datasheet other than what is listed under the section entitled Technical Specifications forms part of the specifications of the product and any benefits specified are not guaranteed. Dialogic may make changes to specifications, product descriptions, and plans at any time, without notice. This document discusses one or more open source products, systems and/or releases. Dialogic is not responsible for your decision to use open source in connection with Dialogic products (including without limitation those referred to herein), nor is Dialogic responsible for any present or future effects such usage might have, including without limitation effects on your products, your business, or your intellectual property rights. Copyright © 2009 Dialogic Corporation All rights reserved. 08/09 11278-02