7773_Data sheet Mem Pro 3/5/07 13:45 Page 1 Dataman MEMPro www.dataman.com • 40 pin ZIF socket accepts both 300/600 mil DIP devices up to 40 pin • Advanced pin drivers allow varying voltages The Dataman MEMPro is a PC based universal 40-pin memory to be applied to any programmer with USB 2.0 connectivity. The MEMPro is built to meet the demands of development labs and field engineers for specialized pin delivering signals programming. without overshoot, increasing Dataman MEMPro is a small, fast and powerful programmer supporting programming yield a huge range of programmable memory types - EPROM, EEPROM, NVRAM, Flash EPROM and serial EEPROM - including low voltage • Pin drivers operate types. MEMPro isn't only a programmer, but also a static RAMs tester. down to 1.8V so you'll be ready to program Hardware: the full range of General • 40 powerful TTL pindrivers provide H/L/pull_up/pull_down and read capability for each pin of the socket. tomorrow’s advanced Advanced pindrivers incorporate high-quality high-speed circuitry to deliver signals without overshoot or low-voltage devices ground bounce for all supported devices. Pin drivers operate down to 1.8V so you'll be ready to program the full range of today's advanced low-voltage devices • USB 2.0/1.1 • The programmer performs device insertion tests and contact checks before it programs each device. These capabilities, supported by signature-byte check help prevent chip damage due to operator error connectivity allowing • MEMPro programmer performs programming verifications at the marginal level of supply voltage, which improves programming yield, and guarantees long data retention fast and easy • Easily upgradeable to the 40Pro programmer connection to PC’s and • Various socket converters are available to handle device in PLCC, SOIC, SSOP, TSOP, TSSOP, TQFP, QFN (MLF) laptops and other packages • Upgradeable to 40Pro Base unit (DAC) • Two D/A converters for VCCP and VPP, controllable rise and fall time programmer • VCCP range 2V..7V/350mA • VPP range 2V..25V/200mA • USB 2.0/1.1 compatible interface • Auto calibration • Self test capability 7773_Data sheet Mem Pro 3/5/07 13:45 Page 2 ZIF socket pindriver Programmer (ZIF socket) • 40-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600 mil devices • EPROM: NMOS/CMOS, 27xxx and 27Cxxx series, with 8/16 bit data width, full up to 40-pins support of LV series • Pindrivers: 40 TTL pindrivers, specialized GND/VCC/VPP pindriver • EEPROM: NMOS/CMOS, 28xxx, 28Cxxx, 27EExxx series, with 8/16 bit data width, full support of LV series • FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all pindriver pins; level H selectable from 1.8V up to 5V • Flash EPROM: 28Fxxx, 29Cxxx, 29Fxxx, 29BVxxx, 29LVxxx, 29Wxxx, 49Fxxx series, with 8/16 bit data width, full support of LV series • Continuity test: each pin is tested before every programming operation • Serial E(E)PROM: 24Cxxx, 24Fxxx, 25Cxxx, 45Dxxx, 59Cxxx, 25Fxxx, 25Pxxx, NVM3060, 85xxx, 93Cxxx, full support for LV series ISP connector (useable after upgrade to 40Pro) • Configuration (EE)PROM: 37LVxx, XC17xxxx, AT17xxx, LV series including • 10-pin male type with miss insertion lock • NV RAM: Dallas DSxxx, SGS/Inmos MKxxx, SIMTEK STKxxx, XICOR 2xxx, ZMD • 6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H selectable U63x series from 1.8V up to 5V to handle all (low-voltage including) devices • 1x VCCP voltage (range 2V..7V/100mA) and 1x VPP voltage (range Package Includes: 2V..25V/50mA) • Programmed chip voltage (VCCP) with both source/sink capability and Dataman MEMPro Universal Memory Programmer voltage sense • Dimensions: 160x95x35 mm (6.3x3.7x1.4 inches) • Weight: 500g (17.65 oz) Software: User Interface Switching Power Supply Adaptor • Programmer is driven by an easy-to-use control program with pull-down • Input: 100-240V @ 50-60Hz & 400mA menus, hot keys and on-line help. Selection of device is performed by its • Output: 15V @ 0.5A, 7.5W class, by manufacturer or simply by typing a fragment of vendor name and/or part number • Moulded USB Cable • Standard device-related commands (read, blank check, program, verify, erase) • ISP cable (useable after upgrade to 40Pro) are enhanced by some test functions (insertion test, signature-byte check), and some special functions (autoincrement) • Diagnostic POD for self test of the programmer • All known data formats are supported. Automatic file format detection and • Anti-dust cover for ZIF socket conversion during loading of file • User manual • The rich-featured autoincrement function enables one to assign individual • Software serial numbers to each programmed device - or simply increments a serial • Optional range of adapters and socket converters also available number, or the function enables one to read serial numbers or any programmed device identification signatures from a file • The software also provides extensive information about programmable Warranty and Support: devices including detailed drawings of all available packages. The software • 30 day money back guarantee* - If you don't like it, send it back also provides explanations of chip labelling (prefixes and suffixes) for each of • One year guarantee - One year parts and labour warranty, on the MEMPro the supported chips device programmer • Keeping your programmer software up to date can be a costly business with • Life-Time Technical Support - MEMPro technical support is available free via some programmers. Dataman offers completely FREE software updates our website and telephone helpdesk for life whenever you need them. The latest software is always available from our website • Life-Time Software Updates - MEMPro software updates are available free via our website for life The Dataman MEMPro supports over 8,000 of the most popular memory devices in use today - with future devices being added monthly. Dataman MEMPro *Applies to orders from UK/US office only coverage includes the following device types: www.dataman.com IN THE UK… IN THE US… Available from… Dataman Programmers Ltd. Dataman Inc. Station Road, Maiden Newton 215 East Michigan Avenue Dorset DT2 0AE, UK Orange City, Florida 32763 USA Tel (01300) 320719 Tel (386) 774-7785 Fax (01300) 321012 Fax (386) 774-7796