Dataman 848Pro2 www.dataman.com • Stand-alone operation with touch screen control • Internal control PC driven by Windows XP Embedded • Up to 70% faster programming of high- capacity memory devices • Over 51,000 (Jan 2010) devices supported with The Dataman 848Pro2 is a super fast stand-alone gang programmer with eight independent 48-pin ZIF sockets, ISP capabilities and internal new devices added control PC driven by Windows XP Embedded. The 848Pro2 is built to monthly meet the demands of super fast high volume production programming • Independent modules with minimal operator effort. supporting concurrent Supporting over 51,000 (Jan 2010) devices with new support added programming monthly, the Dataman 848Pro2 can program without the need for • Intelligent pin drivers family-specific modules, giving you the freedom to choose the optimal operate down to 1.8V device for your design. Independent programming options combine with device insertion tests and a user friendly interface to give higher so you'll be ready to programming yields and reduced failure rates. program the full range of tomorrows advanced Hardware low-voltage devices General • The 848Pro2 programmer offers the same advanced features as the 848Pro+ programmer but with up to 70% faster programming of high-capacity memory devices. • ISP capable using the • FPGA based totally reconfigurable 48 powerful TTL pindrivers provide H/L/pull_up/pull_down and read JTAG interface capability for each pin of the socket. Advanced pindrivers incorporate high-quality high-speed circuitry to deliver signals without overshoot or ground bounce for all supported devices. Pin drivers operate down to • Comprehensive 3 years 1.8V so you'll be ready to program the full range of tomorrow's advanced low-voltage devices. • Each programming module performs device insertion tests and contact checks before it programs each parts and labour device. These capabilities, supported by overcurrent protection and signature-byte check, help prevent chip damage due to operator error. warranty • Selftest capability allows diagnostics in the software to thoroughly check the health of the programmer. • Free life-time software • Built-in protection circuits eliminate damage to programming modules and/or programmed devices due to environment or operator failure. All ZIF sockets and ISP connector pins are protected against ESD up to updates 15kV. • The 848Pro2 programmer performs programming verification at the marginal levels of supply voltage, improving programming yield and guaranteeing long data retention. • Wide range of socket converters are available to handle devices in PLCC, SOIC, PSOP, SSOP, TSOP, TSSOP, TQFP, QFN (MLF), SDIP, BGA and other packages. Programmer Specification • Project files are used to control the 848Pro2 and contain user data, chip • 8 x universal programming modules (8 x 48-pin DIL ZIF sockets and 8 x ISP programming setup, chip configuration, auto programming command connectors) sequence. This helps minimize operator error as the project file is normally created by an engineer and then passed to the operator. The optional • Power and operation status LEDs protected mode can be set avoiding unwanted changes to the project file. • Banana jack for ESD wrist strap connection • Each chip may be programmed with different data such as serial number, • Banana jack for connection to ground configuration and calibration information. Module Specification Engineering Mode Control Base Unit (DAC) • This part of the software is focused to the quick and easy preparation of the • On-board intelligence: powerful microprocessor and FPGA based state machine project file for usage in the production mode control software. • Three D/A converters for VCCP, VPP1, and VPP2, controllable rise and fall time • Each programming module is driven by an easy-to-use control program. • VCCP range 0..8V/1A Selecting a device is performed by its class, by manufacturer or simply by typing a fragment of the vendor name and/or part number. • VPP1, VPP2 range 0..26V/1A • Standard device-related commands (read, blank check, program, verify, erase) • Selftest capability are enhanced by test functions (insertion test, signature-byte check) and additional special functions (auto-increment serialisation, production mode - ZIF Socket programming starts immediately after chip is inserted). • 48-pin DIL ZIF socket accepts both 300/600 mil devices up to 48-pin • All known data formats are supported. Automatic file format detection and • Pindrivers: 48 universal conversion performed during loading of file. • VCCP/VPP1/VPP2 can be connected to each pin • The software provides extensive information about programmable devices including detailed drawings of all available packages. The software also • Perfect ground for each pin provides explanations of chip labelling (prefixes and suffixes). • FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all pindriver pins The Dataman 848Pro2 supports over 51,000 (Jan 2010) of the most popular • Analog pindriver output level selectable from 1.8V up to 26V devices in use today - with new devices being added monthly. Dataman 848Pro2 • Current limitation, overcurrent shutdown, power failure shutdown coverage includes the following device types: • ESD protection on each pin (IEC1000-4-2: 15kV air, 8kV contact) Programmer (ZIF Socket) • Continuity test: each pin is tested before every programming operation EPROM, EEPROM, Flash EPROM, NAND Flash, LBA-NAND, mDOC H3, multi-chip devices, FRAM, MRAM, NV RAM, PROM, Serial E(E)PROM, Serial Flash, Configuration (EE)PROM, 1-Wire E(E)PROM, PLD, FPGA, Clocks, Microcontrollers ISP Connector Programmer (ISP Connector) • 20-pin male type with missinsertion lock Serial E(E)PROM, 1-Wire E(E)PROM, Serial Flash, Microcontrollers, PLD, FPGA • 6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H selectable from 1.8V up to 5V to handle all (including low-voltage) devices • 1x VCCP voltage (range 2V..7V/100mA), can be applied to two pins Package Includes: • Programmed chip voltage (VCCP) with both source/sink capability and • Dataman 848Pro2 Stand-Alone Production Programmer Processor: Intel Core 2 Quad 2.66GHz voltage sense Operating system: Windows XP Embedded • 1x VPP voltage (range 2V..25V/50mA), can be applied to six pins Dimensions: 625 x 465 x 115mm (24.6 x 18.3 x 4.5inches) • Target system supply voltage (range 2V..6V/250mA) Weight: 14.9kg (32.85lb • ESD protection on each pin (IEC1000-4-2: 15kV air, 8kV contact) Operating voltage: 100-240V AC Power consumption: max. 300W active • Input signal, switch YES! equivalent (active level: max. 0.8V) • ISP cable (x8) • Diagnostic POD for selftest of the programmer (x1) Software: • Diagnostic POD for selftest of the ISP connector (x1) User Interface • Anti-dust cover for ZIF socket (x8) There are two ways to control and monitor the 848Pro2 programmer: • ESD wrist strap with cord and banana plug • The graphical control unit with touch screen provides essential information about the programming flow and allows basic control of the 848Pro2 • Vacuum pen • Using a display, keyboard and mouse allows access to all programming flow • User manual information and options. • Software • Optional range of adapters and socket converters also available Production Mode Control • This part of the software is focused to the easy monitoring of high-volume production operations. Warranty and Support • Operator-friendly control software combines many powerful functions with • 30 day money back guarantee* - If you don't like it, send it back. ease of use. Graphic user interface provides an overview of important • Three year guarantee - Three years parts and labour warranty, on the information, reducing the burden on the operator with unnecessary details. 848Pro2 universal gang programmer. • Life-Time Technical Support - 848Pro2 technical support is available free via our website and telephone helpdesk for life. • Life-Time Software Updates – 848Pro2 software updates are available free via our website for life. *Applies to orders from UK/US offices only www.dataman.com IN THE UK… IN THE US… Available from… Dataman Programmers Ltd. Dataman Inc. Station Road, Maiden Newton 215 East Michigan Avenue Dorset DT2 0AE, UK Orange City, Florida 32763 USA Tel (01300) 320719 Tel (386) 774-7785 Fax (01300) 321012 Fax (386) 774-7796 02/10 Windows is a registered trademark of Microsoft Corporation in the United States and other countries.