Catalog 0900P-4 Pneumatic Actuator Products Global Pneumatics, Warning, Offer of Sale This icon can be found next to products that are widely  supported by Parker Pneumatics’ worldwide manufacturing  and sales network.  When you see this icon, you can  be confident that this product is manufactured and/or  stocked* worldwide for rapid delivery.  In addition to local  manufacturing or inventory, our sales network has been  specifically trained on these products to provide our  customers with the best possible service.   Global Products not showing this icon are still sold and distributed  worldwide.  However, The Global Pneumatics icon represents  Pneumatics products that customers can expect the best level of support. If you are a multi-national company, seek global sourcing or  ship globally, depend on Parker Pneumatic for PREMIER CUSTOMER SERVICE. * Stocking levels vary by country          !    WARNING FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN  OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide  product and/or system options for further investigation by users h aving technical expertise.  It is important that you analyze all  aspects of your application including consequences of any failure, and review the information concerning the product or system  in the current product catalog.  Due to the variety of operating conditions and applications for these products or systems, the  user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and  assuring that all performance, safety and warning requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing,  are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice. Offer of Sale The  items  described  in  this  document  are  hereby  offered  for  sale  by  Parker  Hannifin  Corporation,  its  subsidiaries  or  its  authorized distributors.  This offer and its acceptance are governed by the provisions stated on the separate page of this  document entitled “Offer of Sale”. © Copyright 2008 Parker Hannifin Corporation. All Rights Reserved Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics 2A/2AN Series Heavy Duty Air Cylinders Contents Features ..........................................................................B144 Spherical Bearing Mounting .................................. B172-B173 Ordering Information........................................................B145 Double Rod Models .........................................................B174 Mounting Styles ...............................................................B146 Style 55 Rod End .............................................................B175 How to Order ...................................................................B147 Adjustable Cushions ........................................................B176 Specifications ........................................................ B148-B149 Non-Lube Cylinder (2AN) ................................................B177 Mounting Dimensions 1" to 6" Bores ..................... B150-B159 Cylinder Accessories ............................................. B178-B180 Mounting Dimensions 7" Bores ............................. B160-B161 Service Kits ........................................................... B181-B183 Mounting Dimensions 8" to 14" Bores ................... B162-B171 Parker Hannifin Corporation B143 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Features 2A / 2AN Series Piston Rod – Medium carbon steel, induction case-hardened, hard chrome- plated and polished to 10 RMS finish. Primary Seal – Piston rods are made from 90,000 to Unique Serrated 100,000 PSI minimum yield material in 1/2" Lipseal™ is a proven through 4" diameters. Larger diameters vary leakproof design, Piston Rod Stud – Steel Head – Bored between 57,000 and 90,000 PSI minimum completely self- Furnished on 2" and grooved to provide material, depending on rod diameter. The compensating and self- diameter rods and concentricity for mating piston thread equals the catalog style #4 relieving to withstand smaller when standard parts. rod end thread for each rod diameter to variations and conform style #4 rod end assure proper piston-to-rod thread strength. to mechanical threads are required. Ports – NPTF ports Two wrench flats are provided for rod end deflection that may Also available in 2 are standard. attachment. occur. times the catalog “A” dimension length. Studs have rolled threads Steel Cap – Bored and grooved and are made from End Seals – to provide concentricity for mating high strength steel. Pressure-actuated parts. Anaerobic adhesive is cylinder body-to- used to permanently head and cap lock the stud to the Ports – NPTF ports “O” rings. piston rod. are standard. Alloy Steel Tie Rod Nuts Align-A-Groove – High Strength Secondary (Patent #3043639) – A 3/16" Tie Rods – Made “Jewel” Rod Gland Seal – wide surface machined at from 100,000 PSI Assembly – Externally Double-Service each end of the cylinder minimum yield steel removable without Wiperseal™ body. Makes precise with rolled threads for cylinder disassembly. acts as mounting quick and easy. added strength. Long bearing surface a secondary is inboard of the seals, pressure seal The Cylinder Body – assuring positive on the extend Adjustable Floating Cushions Hard chrome-plated bore, lubrication from within stroke and – Cushions are optional and can be steel tubing honed to a 15 the cylinder. An “O” cleans the rod supplied at head end, cap end, or micro inch finish on 1-1/2" ring is used as a seal on the retur OPTIONAL PIST n both ends without change in en ONS velope through 14" bore sizes. 1" between gland and stroke. or mounting dimensions. bore size is aluminum with head, and also serves hard-coated bore. as a prevailing torque- type lock. One-Piece Nodular Iron Piston – The wide piston surface contacting cylinder Piston Lipseal – Fully Prelubricated Wearing Surfaces bore reduces bearing loads. BRONZE dynamic and self-com- PHENOLIC FILLED Parker Series 2A Air Cylinders are factory Anaerobic adhesive is used to BEARINGS TEFLON RINGS pensating for variations in prelubricated. Lube-A-Cyl applied to seals, permanently lock and seal the pressure, mechanical piston, cylinder bore, piston rod and gland piston to the rod. deflections and wear. surfaces provides lubrication for normal Pistons on Cylinder operation. Lube-A-Cyl has been field and Bores 8" and larger come laboratory tested, and is recommended standard with a wear band by Parker for air cylinders where lubricant For guided version of the 2A cylinder, to ensure long service life. should remain in the cylinder and not be SYNTHETIC RUBBER please see the HB Series in Section F. EXPANDER RINGS expelled into the atmosphere. Piston with Retainer Nut – Optional at extra charge. Parker Hannifin Corporation B144 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Heavy Duty Air Cylinders Catalog 0900P-4 2A / 2AN Series Model Numbers Series 2A Model Numbers – How to Develop Them – How to “Decode” Them Parker Series 2A cylinders can be completely and accurately described by a model number consisting of coded symbols. To develop a model number, select only those symbols that represent the cylinder required, and place them in the sequence indicated below. 6.00 C K F 2A U S 1 4 A C 12.000 Bore Series* Piston Rod 2 Stroke* Size* Number* 2A Std. Specify Specify 2AN Non- For single rod in inches. in cylinders, select Lube inches. one only. Note: Check Cushion Cushion rod selection chart Cap End in Engineering Head End Section for Use “C” only Use “C” only appropriate piston if cushion if cushion head rod diameter. cap end is end is required. required. Double Rod** Special Piston Rod Threads* Modifications Use “K” only if A UNF Standard double rod cylinder Use “S” only if special W BSF (British Fine) is required. modifications are M Metric required. Do not use “S” for rod Mounting Style* end modifications. Piston Rod TB, TC, TD, J, H, JB, HB, 1 Alternate Thread C, F, BB, D, DB, DD , SB Blank Standard Length Common Modifications 2 Stud two times Blank None Mounting Modifications longer than F Nut Retained Piston Blank None standard V Fluorocarbon Seals P Thrust Key W Water Service (Styles C & F only) Piston Rod End* M Manifold Port O-Ring Seal 4 Small Male (Style C only) Ports* 7 Female Thread for R Removable Trunnions U NPTF (Dry Seal Pipe Thread) Spherical Rod Eye (standard) 8 Intermediate Male T Used only for SAE Straight Thread Combination Mounting Style 9 Short Female (O-Ring Port) 3 Any practical mounting style 55 Rod End for Flange Coupling R Used only for BSP as listed under “Mounting Style”. 3 Special (Specify) (Parallel Thread ISO 228) B Used only for BSPT (Taper Thread ISO 7-Rc) **Double Rod Cylinders G Used only for Metric Thread For double rod cylinders, specify rod Y Used only for Metric Thread per number and rod end symbols for ISO 6149 both piston rods. A typical double rod model number would be: Cylinder serial numbers are factory production record numbers and are 6.00 KJ2AU14A/14A 12.000 assigned to each cylinder in addition to the model number. NOTE: For sensor specifications * Required for Basic Cylinder Model Number and part numbers, please see the 1 Specify XI dimension Electronic Sensors section. 2 In case of Stop Tube, call out gross stroke length (net stroke + stop tube length). 3 For information regarding Style 55 Rod Ends, please refer to page B205. Parker Hannifin Corporation B145 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Styles 2A / 2AN Series Available Mounting Styles Tie Rods Extended Head End Tie Rods Extended Cap End Tie Rods Extended Both Ends Head Rectangular Flange Style TB Style TC Style TD Style J (NFPA MX3) (NFPA MX2) (NFPA MX1) (NFPA MF1) 1"-6", Pg B180 1"-6", Pg B180 7", B190 1"-6", Pg B180 8"-14", Pg B192 1"-6", Pg B180 8"-14", Pg B192 8"-14", Pg B192 Head Square Flange Cap Rectangular Flange Cap Square Flange Side Lug Style JB Style H Style HB Style C (NFPA MF5) (NFPA MF2) (NFPA MF6) (NFPA MS2) 1"-6", Pg B182 1"-6", Pg B182 1"-6", Pg B184 7", B190 7", B190 7", B191 8"-14", Pg B192 1"-6", Pg B180 8"-14", Pg B192 8"-14", Pg B194 Side Tapped Cap Fixed Clevis Head Trunnion Cap Trunnion Style F Style BB Style D Style DB 1"-6", Pg B184 1"-6", Pg B188 1"-6", Pg B186"- 1"-6", Pg B186 (NFPA MS4) (NFPA MP1) (NFPA MT1) (NFPA MT2) 8"-14", Pg B196 7", B191 14", Pg B200 7", B191 8"-14", Pg B198 8"-14", Pg B200 Intermediate Fixed Trunnion Spherical Bearing Double Rod Cylinders Style KTB Shown Style DD Style SB (NFPA MT4) Most of the above illustrated 1-1/2"- 6", Pg B186 1-1/2"- 6", Pg B202 mounting styles are available 8"-14", Pg B200 8"-14", Pg B203 in double rod cylinders. See Catalog page B174. Parker Hannifin Corporation B146 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders How to Order Series Cylinders 2A / 2AN Series When ordering Series 2A cylinders, please review the following: Note: Duplicate cylinders can be ordered by giving the SERIAL Special Modifications: Additional information is required on orders NUMBER from the nameplate of the original cylinder. Factory for cylinders with special modifications. This is best handled with records supply a quick positive identification. descriptive notes. For further information, consult factory. Piston Rods: Specify rod code number based on diameter. Give Fluid Medium: Series 2A hydraulic cylinders are equipped with thread style number for a standard thread or specify dimensions. seals for use with lubricated air. See “Style 3 Rod End” below. Cushions: If cushions are required specify according to the model number on the next page. If the cylinder is to have a double rod and only one cushion is required, be sure to specify clearly which end of the cylinder is to be cushioned. Class 1 Seals Piston Rod Wiper – Nitrile Class 1 seals are the seals provided as standard in a cylinder Piston Seals – Nitrile with polymyte back-up washers assembly unless otherwise specified. For further information on O-Rings – Nitrile fluid compatibility or operating limitations of all components, see section C. For the 2A series cylinders the following make-up Class 1 Seals: Primary Piston Rod Seal – Nitrile with PTFE back-up washers Combination Mountings page in this section. For this option the piston rod number, piston rod Single Rod End The first mounting is the one called out on the head end, and piston rod threads are to be specified for both ends. The end of the cylinder. The second or subsequent mountings are called simplest are for symmetric cylinders such as: TD, C, E, F, G, and out as they appear in the assembly moving away from the rod end. CB mounts. All other mounting styles, the description of the first rod Exception: When tie rod mountings are part of a combination, the end will be at the mounting end. In the case of multiple mounts, the model number should contain an “S” (Special) in the model code and description of the first rod end will be at the primary mounting end. a note in the body of the order clarifying the mounting arrangement. For “DD” mounts, the description of the first rod end will be the same The ”P” is used to define a thrust key and is not considered to be a location as the “XI” dimension. mounting. However, it is located at the primary end. Example: 4.00 KDD2ALT24A/18A x 10.000 XI=8 Example: 4.00 CCBB2ALTS14AC x 10.000 This is a center trunnion mounting cylinder with the XI dimension Combination “C” mounting head only. “BB” mounting cap end measured from the code 2 rod side of the cylinder which has the This cylinder is also cushioned at both ends. style 4 thread. The opposite end code 1 rod with the style 8 thread. Double Rod End In general, the model number is read left to right corresponding to the cylinder as viewed from left to right with the primary end at rod end #1. See Double Rod Models information Style 3 Rod End during assembly or maintenance. Standard style 55 rod ends with A style 3 rod end indicates a special rod end configuration. All a longer than standard WG dimension should call out a style 3 rod special piston rod dimensions must have all three: KK; A; W/WF or end and the note: same as 55 except WG=____. A drawing should LA/LAF specified with the rod fully retracted. A sketch or drawing be submitted for special 55 rod ends that have specific tolerances or should be submitted for rod ends requiring special machining such special radii. Special rod ends that have smaller than standard male as snap ring grooves, keyways, tapers, multiple diameters, etc. It threads, larger than standard female threads, or style 55 rod ends is good design practice to have this machining done on a diameter with smaller than standard AF or AE dimensions are to be reviewed at least 0.065 inches smaller than the piston rod diameter. This by Engineering for proper strength at operating pressure. allows the piston rod to have a chamfer preventing rod seal damage Service Policy Certified Dimensions On cylinders returned to the factory for repairs, it is standard policy Parker Cylinder Division guarantees that all cylinders ordered from this catalog will be built to dimensions shown. All dimensions for the Cylinder Division to make such part replacements as will put are certified to be correct, and thus it is not necessary to request the cylinder in as good as new condition. Should the condition of certified drawings. the returned cylinder be such that expenses for repair would exceed the costs of a new one, you will be notified. Address all correspondence and make shipments to, Service Department at your nearest regional plant listed in the pages of this catalog. Parker Hannifin Corporation B147 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Specifications 2A / 2AN Series Standard Specifications • Heavy Duty Service – ANSI/(NFPA) T3.6.7R2-1996 Specifications and Mounting Dimension Standards • Standard Construction – Square Head – Tie Rod Design • Nominal Pressure – Up to 250 PSI Air Service • Standard Fluid – Filtered Air • Standard Temperature* – -10°F to +165°F • Bore Sizes – 1" through 14" (Larger sizes available)** • Piston Rod Diameter – 1/2" through 5-1/2" ** • Mounting Styles – 15 standard styles at various application ratings • Strokes – Available in any practical stroke length • Cushions – Optional at either end or both ends of stroke. “Float Check” at cap end. • Rod Ends – Three Standard Choices – Specials to Order * See page A4, “Operating Fluids and Temperature Range” for higher temperature service. ** See table below for standard bore sizes and available piston rod diameters. NOTE: Series 2A Air Cylinders fully meet ANSI/(NFPA) T3.6.7R2- 1996 Specifications and Mounting Dimension Standards for Square Head Industrial Fluid Power Cylinders. Parker Style TB, JB, HB, C, DB, and BB are available in 7" bore size, see pages C190-C191. In line with our policy of continuing product improvement, specifications in this catalog are subject to change. Available Bore Sizes and Piston Rod Diameters Piston Rod Diameter Bore Size 1/2" 5/8" 1" 1-3/8" 1-3/4" 2" 2-1/2" 3" 3-1/2" 4" 4-1/2" 5" 5-1/2" 1" l l 1-1/2" l l 2" l l l 2-1/2" l l l l 3-1/4" l l l l 4" l l l l l 5" l l l l l l l 6" l l l l l l l 8" l l l l l l l l l l 10" l l l l l l l l l 12" l l l l l l l l 14" l l l l l l l Parker Hannifin Corporation B148 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Cylinder Weights 2A / 2AN Series The weights shown in Tables A and B are for Parker Series extra rod extension use piston rod weights per inch shown in 2A/2AN cylinders with various piston rod diameters. To Table B. Weights of cylinders with intermediate rods may be determine the net weight of a cylinder, first select the proper estimated from table below by taking the difference between basic weight for zero stroke, then calculate the weight of the the piston rod weights per inch and adding it to the Code 1 cylinder stroke and add the result to the basic weight. For weight for the cylinder bore size involved. Table A Cylinder Weights, in pounds, for Series 2A/2AN cylinders Single Rod Cylinders Add Per Inch Double Rod Cylinders Add Per Inch Basic Wt. Zero Stroke of Stroke Basic Wt. Zero Stroke of Stroke T, TB, TC, BB, C, D, DB KF, KJ KT KC, KD Bore Rod Size Dia. TD, F, H, J DD, HB, JB 2A, 2AN KTB, KTD KDD, KJB 2A, 2AN 1/2" 2.5 2.9 .20 4.7 5.5 .40 1" 5/8" 2.6 3.0 .23 4.9 5.7 .46 5/8" 3.7 4.3 .3 4.2 4.8 .6 1-1/2" 1" 4.5 5.1 .4 5.8 6.7 .8 5/8" 6.5 6.9 .5 8.2 8.6 1.0 2" 1" 7.0 7.5 .63 9.0 9.5 1.3 1-3/8" 8.5 8.9 .8 11.2 11.6 1.6 5/8" 9.0 9.7 .6 11.4 12.1 1.2 2-1/2" 1" 9.5 10.0 .73 12.0 12.5 1.5 1-3/4" 13.2 13.6 1.1 19.8 20.5 2.2 1" 16.5 17.5 .8 22.0 23.0 1.6 3-1/4" 1-3/8" 17.0 18.0 1.0 22.5 23.5 2.0 2" 27.0 28.0 1.4 43.0 44.0 2.8 1" 26.0 31.0 1.0 33.0 38.0 2.0 4" 1-3/8" 26.5 31.5 1.2 33.5 38.5 2.5 2-1/2" 36.0 42.0 2.0 53.0 58.0 4.0 1" 39.0 46.0 1.1 48.0 55.0 2.2 5" 1-3/8" 39.5 46.5 1.3 48.5 55.5 2.6 3-1/2" 63.0 66.0 3.6 96.0 103.0 7.2 1-3/8" 68.0 77.0 1.5 80.0 89.0 3.0 6" 4" 100.0 102.0 4.5 144.0 153.0 9.0 1-3/8" 80.0 85.0 2.0 92.0 97.0 4.0 7" 2" 82.0 87.0 3.5 96.0 101.0 7.0 1-3/8" 94.0 99.0 2.0 108.0 113.0 4.0 8" 51/2" 168.0 172.0 8.0 256.0 261.0 16.0 1-3/4" 182.0 188.0 2.5 178.0 184.0 5.0 10" 5-1/2" 258.0 264.0 8.5 330.0 335.0 17.0 2" 274.0 282.0 3.5 270.0 280.0 7.0 12" 5-1/2" 350.0 358.0 9.5 420.0 430.0 19.0 2-1/2" 435.0 448.0 4.5 440.0 655.0 9.0 14" 5-1/2" 510.0 519.0 10.0 490.0 705.0 20.0 Table B Piston Rod Wt. Piston Rod Wt. Piston Rod Wt. Rod Dia. Per Inch Rod Dia. Per Inch Rod Dia. Per Inch 5/8" 0.09 2" 0.89 4" 3.56 1" 0.22 2-1/2" 1.40 4-1/2" 4.51 1-3/8" 0.42 3" 2.00 5" 5.56 1-3/4" 0.68 3-1/2" 2.72 5-1/2" 6.72 Parker Hannifin Corporation B149 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 1" to 6" Bore Sizes Series 2A C052 Basic Mounting (T) — Tie Rods Extended* NFPA MX0 — no tie rods extended ZB + STROKE Style TB can be supplied upon request. Y P + STROKE LB + STROKE (NFPA Style MX3) W E EE 1 AA MM E 4 2 R DD 3 G J K BB F R * Style TB (NFPA MX3), Head Tie Rods Extended, illustrated. Style TC (NFPA MX2), Cap Tie Rods Extended; and Style TD (NFPA MX1), Both Ends Tie Rods Extended are also available. All “T” styles can be dimensioned from Style TB drawing at right. Head Rectangular Flange ZB + STROKE Style J Y P + STROKE LB + STROKE (NFPA Style MF1) W UF EE 1 E 4 2 R MM 3 J K F G FB E WF 4 HOLES TF Cap Rectangular Flange ZF + STROKE Style H Y P + STROKE LB + STROKE (NFPA Style MF2) W UF EE 1 MM R 2 4 E K 3 G J F F E XF TF Rod End Dimensions — see table 2 Thread Style 4 Thread Style 8 Thread Style 9 “Special” Thread (NFPA Style SM) (NFPA Style IM) (NFPA Style SF) Style 3 Small Male Intermediate Male Small Female Special thread, LA LA A extension, rod eye, A W A W blank, etc., are also 1/8 C V C V KK CC KK available. To order, specify “Style 3” and give MM B MM B MM B desired dimensions D WRENCH FLATS for CC or KK, A NA NA NA D WRENCH D WRENCH 1/8 1/8 FLATS FLATS C V and LA. If otherwise W special, furnish A high strength rod end stud is supplied on thread style 4 through style 4 rod ends are recommended through 2" piston rod diameters dimensioned sketch. and style 8 rod ends are recommended on larger diameters. Use 2" diameter rods. Larger sizes or special rod ends are cut threads. Style 4 rod ends are recommended where the workpiece is secured style 9 for applications where female rod end threads are required. against the rod shoulder. When the workpiece is not shouldered, If rod end is not specified, style 4 will be supplied. Parker Hannifin Corporation B150 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 1" to 6" Bore Sizes Series 2A C052 Table 1—Envelope and Mounting Dimensions Add Stroke EE Bore AA BB DD E NPTF F FB G J K R TF UF LB P 1* 1.53 3/4 10-24 n 1/4 3/8 1/4 1-1/2 1 3/16 1.08 2 2-1/2 3-7/8 2-1/8 1-1/2 2.02 1 1/4-28 2 3/8** 3/8 5/16 1-1/2 1 1/4 1.43 2-3/4 3-3/8 4 2-1/4 2 2.6 1-1/8 5/16-24 2-1/2 3/8** 3/8 3/8 1-1/2 1 5/16 1.84 3-3/8 4-1/8 4 2-1/4 2-1/2 3.1 1-1/8 5/16-24 3 3/8** 3/8 3/8 1-1/2 1 5/16 2.19 3-7/8 4-5/8 4-1/8 2-3/8 3-1/4 3.9 1-3/8 3/8-24 3-3/4 1/2 5/8 7/16 1-3/4 1-1/4 3/8 2.76 4-11/16 5-1/2 4-7/8 2-5/8 4 4.7 1-3/8 3/8-24 4-1/2 1/2 5/8 7/16 1-3/4 1-1/4 3/8 3.32 5-7/16 6-1/4 4-7/8 2-5/8 5 5.8 1-13/16 1/2-20 5-1/2 1/2 5/8 9/16 1-3/4 1-1/4 7/16 4.10 6-5/8 7-5/8 5-1/8 2-7/8 6 6.9 1-13/16 6-1/2 3/4 3/4 9/16 2 1-1/2 7/16 4.88 7-5/8 8-5/8 5-3/4 3-1/8 * Cushions not available on 1" bore. ** On 1", 1-1/2", 2" and 2-1/2" bore sizes, the head-end (only) pipe thread is not full depth on cylinders with No. 2 rods. Minimum of three full threads available. n 1" bore head dimension is 1-3/4" x 1-1/2". See page B183. Table 3 — Envelope and Table 2—Rod Dimensions Mounting Dimensions Thread Rod Extensions and Pilot Dimensions Add Stroke Rod Style Style +.000 Rod Dia. 8 4 & 9 -.002 Bore No. MM CC KK A B C D LA NA V W WF Y XF ZB ZF 1(Std.) 1/2 7/16-20 5/16-24 5/8 .999 3/8 3/8 1-1/4 7/16 1/4 5/8 1 1-15/16 4-1/2 4-11/16 4-7/8 1 2 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1 1-15/16 4-1/2 4-11/16 4-7/8 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1 1-15/16 4-5/8 4-7/8 5 1-1/2 2 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 1-3/8 2-5/16 5 5-1/4 5-3/8 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1 1-15/16 4-5/8 4-15/16 5 2 2 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-7/8 1-5/16 5/8 1-1/4 1-5/8 2-9/16 5-1/4 5-9/16 5-5/8 3 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 1-3/8 2-5/16 5 5-5/16 5-3/8 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1 1-15/16 4-3/4 5-1/16 5-1/8 2 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/2 1-11/16 3/4 1-1/2 1-7/8 2-13/16 5-5/8 5-15/16 6 2-1/2 3 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 1-3/8 2-5/16 5-1/8 5-7/16 5-1/2 4 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-7/8 1-5/16 5/8 1-1/4 1-5/8 2-9/16 5-3/8 5-11/16 5-3/4 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 1-3/8 2-7/16 5-5/8 6 6-1/4 2 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 2 3-1/16 6-1/4 6-5/8 6-7/8 3-1/4 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 1-5/8 2-11/16 5-7/8 6-1/4 6-1/2 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 1-7/8 2-15/16 6-1/8 6-1/2 6-3/4 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 1-3/8 2-7/16 5-5/8 6 6-1/4 2 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-5/8 2-3/8 5/8 1-5/8 2-1/4 3-5/16 6-1/2 6-7/8 7-1/8 4 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 1-5/8 2-11/16 5-7/8 6-1/4 6-1/2 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 1-7/8 2-15/16 6-1/8 6-1/2 6-3/4 5 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 2 3-1/16 6-1/4 6-5/8 6-7/8 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 1-3/8 2-7/16 5-7/8 6-5/16 6-1/2 2 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5-1/8 3-3/8 5/8 1-5/8 2-1/4 3-5/16 6-3/4 7-3/16 7-3/8 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 1-5/8 2-11/16 6-1/8 6-9/16 6-3/4 5 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 1-7/8 2-15/16 6-3/8 6-13/16 7 5 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 2 3-1/16 6-1/2 6-15/16 7-1/8 6 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-5/8 2-3/8 5/8 1-5/8 2-1/4 3-5/16 6-3/4 7-3/16 7-3/8 7 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5-1/8 2-7/8 5/8 1-5/8 2-1/4 3-5/16 6-3/4 7-3/16 7-3/8 1(Std.) 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-1/2 1-5/16 1/4 7/8 1-5/8 2-13/16 6-5/8 7-1/16 7-3/8 2 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 2-1/4 3-7/16 7-1/4 7-11/16 8 3 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/8 1-11/16 3/8 1-1/8 1-7/8 3-1/16 6-7/8 7-5/16 7-5/8 6 4 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 2 3-3/16 7 7-7/16 7-3/4 5 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 2-1/4 3-7/16 7-1/4 7-11/16 8 6 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 2-1/4 3-7/16 7-1/4 7-11/16 8 7 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 2-1/4 3-7/16 7-1/4 7-11/16 8 Parker Hannifin Corporation B151 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 1" to 6" Bore Sizes Series 2A C052 Head Square Flange Style JB (NFPA Style MF5) ZB + STROKE UF Y P + STROKE E LB + STROKE 1 W EE UF E 2 R TF MM 4 J K F G 3 FB R WF 8 HOLES TF Cap Square Flange Style HB (NFPA Style MF6) ZF + STROKE UF Y P + STROKE E LB + STROKE W 1 EE MM TF R 2 4 E UF K G F J F 3 XF FB R 8 HOLES TF Rod End Dimensions — see table 2 Thread Style 4 Thread Style 8 Thread Style 9 “Special” Thread (NFPA Style SM) (NFPA Style IM) (NFPA Style SF) Style 3 Small Male Intermediate Male Small Female Special thread, LA LA A extension, rod eye, A W A W blank, etc., are also 1/8 C V C V KK CC KK available. To order, specify “Style 3” and give MM B MM B MM B desired dimensions D WRENCH FLATS for CC or KK, A NA NA NA D WRENCH D WRENCH 1/8 1/8 FLATS FLATS C V and LA. If otherwise W special, furnish dimensioned sketch. A high strength rod end stud is supplied on thread style 4 through style 4 rod ends are recommended through 2" piston rod diameters 2" diameter rods. Larger sizes or special rod ends are cut threads. and style 8 rod ends are recommended on larger diameters. Use Style 4 rod ends are recommended where the workpiece is secured style 9 for applications where female rod end threads are required. against the rod shoulder. When the workpiece is not shouldered, If rod end is not specified, style 4 will be supplied. Parker Hannifin Corporation B152 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 1" to 6" Bore Sizes Series 2A C052 Table 1—Envelope and Mounting Dimensions 1-1/2 Add Stroke EE 1 Bore E NPTF F FB G J K R TF UF LB P 1* n 1/4 3/8 1/4 1-1/2 1 3/16 1.08 2 2-1/2 3-7/8 2-1/8 1-1/2 2 3/8** 3/8 5/16 1-1/2 1 1/4 1.43 2-3/4 3-3/8 4 2-1/4 2 2-1/2 3/8** 3/8 3/8 1-1/2 1 5/16 1.84 3-3/8 4-1/8 4 2-1/4 2-1/2 3 3/8** 3/8 3/8 1-1/2 1 5/16 2.19 3-7/8 4-5/8 4-1/8 2-3/8 4 2 1.08 3-1/4 3-3/4 1/2 5/8 7/16 1-3/4 1-1/4 3/8 2.76 4-11/16 5-1/2 4-7/8 2-5/8 4 4-1/2 1/2 5/8 7/16 1-3/4 1-1/4 3/8 3.32 5-7/16 6-1/4 4-7/8 2-5/8 1.53 DIA. 5 5-1/2 1/2 5/8 9/16 1-3/4 1-1/4 7/16 4.10 6-5/8 7-5/8 5-1/8 2-7/8 6 6-1/2 3/4 3/4 9/16 2 1-1/2 7/16 4.88 7-5/8 8-5/8 5-3/4 3-1/8 3 * Cushions not available on 1" bore. ** On 1", 1-1/2", 2" and 2-1/2" bore sizes, the head-end (only) pipe thread is not full depth on cylinders 1.08 with No. 2 rods. Minimum of three full threads available. Head Dimensions for 1" Bore Size n 1" bore head dimension is 1-3/4" x 1-1/2". See drawing at right. (Cap is 1-1/2" square.) Table 3 — Envelope and Table 2—Rod Dimensions Mounting Dimensions Thread Rod Extensions and Pilot Dimensions Add Stroke Rod Style Style +.000 Rod Dia. 8 4 & 9 -.002 Bore No. MM CC KK A B C D LA NA V W WF Y XF ZB ZF 1(Std.) 1/2 7/16-20 5/16-24 5/8 .999 3/8 3/8 1-1/4 7/16 1/4 5/8 1 1-15/16 4-1/2 4-11/16 4-7/8 1 2 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1 1-15/16 4-1/2 4-11/16 4-7/8 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1 1-15/16 4-5/8 4-7/8 5 1-1/2 2 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 1-3/8 2-5/16 5 5-1/4 5-3/8 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1 1-15/16 4-5/8 4-15/16 5 2 2 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-7/8 1-5/16 5/8 1-1/4 1-5/8 2-9/16 5-1/4 5-9/16 5-5/8 3 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 1-3/8 2-5/16 5 5-5/16 5-3/8 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1 1-15/16 4-3/4 5-1/16 5-1/8 2 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/2 1-11/16 3/4 1-1/2 1-7/8 2-13/16 5-5/8 5-15/16 6 2-1/2 3 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 1-3/8 2-5/16 5-1/8 5-7/16 5-1/2 4 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-7/8 1-5/16 5/8 1-1/4 1-5/8 2-9/16 5-3/8 5-11/16 5-3/4 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 1-3/8 2-7/16 5-5/8 6 6-1/4 2 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 2 3-1/16 6-1/4 6-5/8 6-7/8 3-1/4 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 1-5/8 2-11/16 5-7/8 6-1/4 6-1/2 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 1-7/8 2-15/16 6-1/8 6-1/2 6-3/4 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 1-3/8 2-7/16 5-5/8 6 6-1/4 2 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-5/8 2-3/8 5/8 1-5/8 2-1/4 3-5/16 6-1/2 6-7/8 7-1/8 4 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 1-5/8 2-11/16 5-7/8 6-1/4 6-1/2 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 1-7/8 2-15/16 6-1/8 6-1/2 6-3/4 5 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 2 3-1/16 6-1/4 6-5/8 6-7/8 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 1-3/8 2-7/16 5-7/8 6-5/16 6-1/2 2 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5-1/8 3-3/8 5/8 1-5/8 2-1/4 3-5/16 6-3/4 7-3/16 7-3/8 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 1-5/8 2-11/16 6-1/8 6-9/16 6-3/4 5 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 1-7/8 2-15/16 6-3/8 6-13/16 7 5 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 2 3-1/16 6-1/2 6-15/16 7-1/8 6 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-5/8 2-3/8 5/8 1-5/8 2-1/4 3-5/16 6-3/4 7-3/16 7-3/8 7 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5-1/8 2-7/8 5/8 1-5/8 2-1/4 3-5/16 6-3/4 7-3/16 7-3/8 1(Std.) 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-1/2 1-5/16 1/4 7/8 1-5/8 2-13/16 6-5/8 7-1/16 7-3/8 2 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 2-1/4 3-7/16 7-1/4 7-11/16 8 3 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/8 1-11/16 3/8 1-1/8 1-7/8 3-1/16 6-7/8 7-5/16 7-5/8 6 4 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 2 3-3/16 7 7-7/16 7-3/4 5 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 2-1/4 3-7/16 7-1/4 7-11/16 8 6 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 2-1/4 3-7/16 7-1/4 7-11/16 8 7 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 2-1/4 3-7/16 7-1/4 7-11/16 8 Parker Hannifin Corporation B153 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics 1-3/4 1-1/2 Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 1" to 6" Bore Sizes Series 2A C052 Side Lug Style C (NFPA Style MS2) ZB + STROKE Y P + STROKE LB + STROKE W US EE 1 4 2 MM E E -.005 2 -.010 ST 3 G J K SB F E SW SW 4 HOLES SW SU SU SW SW TS SW XS SS + STROKE Side Tapped Style F (NFPA Style MS4) ZB + STROKE Y P + STROKE LB + STROKE W E EE 1 E 4 2 MM E -.005 2 -.010 3 K G J F TN NT THREAD, ND DEEP XT SN + STROKE 4 TAPPED MTG. HOLES Rod End Dimensions — see table 2 Thread Style 4 Thread Style 8 Thread Style 9 “Special” Thread (NFPA Style SM) (NFPA Style IM) (NFPA Style SF) Style 3 Small Male Intermediate Male Small Female Special thread, LA LA A extension, rod eye, A W A W blank, etc., are also 1/8 C V C V KK CC KK available. To order, specify “Style 3” and give MM B MM B MM B desired dimensions D WRENCH FLATS for CC or KK, A NA NA NA D WRENCH D WRENCH 1/8 1/8 FLATS FLATS C V and LA. If otherwise W special, furnish dimensioned sketch. A high strength rod end stud is supplied on thread style 4 through style 4 rod ends are recommended through 2" piston rod diameters 2" diameter rods. Larger sizes or special rod ends are cut threads. and style 8 rod ends are recommended on larger diameters. Use Style 4 rod ends are recommended where the workpiece is secured style 9 for applications where female rod end threads are required. against the rod shoulder. When the workpiece is not shouldered, If rod end is not specified, style 4 will be supplied. Parker Hannifin Corporation B154 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 1" to 6" Bore Sizes Series 2A C052 Table 1—Envelope and Mounting Dimensions Add Stroke EE Bore E NPTF F G J K NT SB* ST SU SW TN TS US LB P SN SS 1* n 1/4 3/8 1-1/2 1 3/16 10-24 9/32 5/16 3/4 5/16 9/16 2-1/8 2-3/4 3-7/8 2-1/8 2-1/8 2-7/8 1-1/2 2 3/8** 3/8 1-1/2 1 1/4 1/4-20 7/16 1/2 15/16 3/8 5/8 2-3/4 3-1/2 4 2-1/4 2-1/4 2-7/8 2 2-1/2 3/8** 3/8 1-1/2 1 5/16 5/16-18 7/16 1/2 15/16 3/8 7/8 3-1/4 4 4 2-1/4 2-1/4 2-7/8 2-1/2 3 3/8** 3/8 1-1/2 1 5/16 3/8-16 7/16 1/2 15/16 3/8 1-1/4 3-3/4 4-1/2 4-1/8 2-3/8 2-3/8 3 3-1/4 3-3/4 1/2 5/8 1-3/4 1-1/4 3/8 1/2-13 9/16 3/4 1-1/4 1/2 1-1/2 4-3/4 5-3/4 4-7/8 2-5/8 2-5/8 3-1/4 4 4-1/2 1/2 5/8 1-3/4 1-1/4 3/8 1/2-13 9/16 3/4 1-1/4 1/2 2-1/16 5-1/2 6-1/2 4-7/8 2-5/8 2-5/8 3-1/4 5 5-1/2 1/2 5/8 1-3/4 1-1/4 7/16 5/8-11 1-3/16 1 1-9/16 11/16 2-11/16 6-7/8 8-1/4 5-1/8 2-7/8 2-7/8 3-1/8 6 6-1/2 3/4 3/4 2 1-1/2 7/16 3/4-10 1-3/16 1 1-9/16 11/16 3-1/4 7-7/8 9-1/4 5-3/4 3-1/8 3-1/8 3-5/8 * Cushions not available on 1" bore. ** On 1", 1-1/2", 2" and 2-1/2" bore sizes, the head-end (only) pipe thread is not full depth on cylinders with No. 2 rods. Minimum of three full threads available. • Upper surface spot-faced for socket head screws. n 1" bore head dimension is 1-3/4" x 1-1/2". See page B183. Table 3 — Envelope and Table 2—Rod Dimensions Mounting Dimensions Add Thread Rod Extensions and Pilot Dimensions Stroke Rod Style Style +.000 Rod Dia. 8 4 & 9 -.002 Bore No. MM CC KK A B C D LA NA V W ND XS XT Y ZB 1(Std.) 1/2 7/16-20 5/16-24 5/8 .999 3/8 3/8 1-1/4 7/16 1/4 5/8 1/4 1-5/16 1-15/16 1-15/16 4-11/16 1 2 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1/4 1-5/16 1-15/16 1-15/16 4-11/16 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 5/16 1-3/8 1-15/16 1-15/16 4-7/8 1-1/2 2 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 5/16 1-3/4 2-5/16 2-5/16 5-1/4 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1-1/32 1-3/8 1-15/16 1-15/16 4-15/16 1-1/32 2 2-9/16 2-9/16 5-9/16 2 2 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-7/8 1-5/16 5/8 1-1/4 3 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 1-1/32 1-3/4 2-5/16 2-5/16 5-5/16 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 7/16 1-3/8 1-15/16 1-15/16 5-1/16 2 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/2 1-11/16 3/4 1-1/2 7/16 2-1/4 2-13/16 2-13/16 5-15/16 2-1/2 3 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 7/16 1-3/4 2-5/16 2-5/16 5-7/16 4 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-7/8 1-5/16 5/8 1-1/4 7/16 2 2-9/16 2-9/16 5-11/16 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 1/2 1-7/8 2-7/16 2-7/16 6 2 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 1/2 2-1/2 3-1/16 3-1/16 6-5/8 3-1/4 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 1/2 2-1/8 2-11/16 2-11/16 6-1/4 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 1/2 2-3/8 2-15/16 2-15/16 6-1/2 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 5/8 1-7/8 2-7/16 2-7/16 6 2 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-5/8 2-3/8 5/8 1-5/8 5/8 2-3/4 3-5/16 3-5/16 6-7/8 4 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 5/8 2-1/8 2-11/16 2-11/16 6-1/4 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 5/8 2-3/8 2-15/16 2-15/16 6-1/2 5 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 5/8 2-1/2 3-1/16 3-1/16 6-5/8 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 3/4 2-1/16 2-7/16 2-7/16 6-5/16 2 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5-1/8 3-3/8 5/8 1-5/8 3/4 2-15/16 3-5/16 3-5/16 7-3/16 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 3/4 2-5/16 2-11/16 2-11/16 6-9/16 5 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 3/4 2-9/16 2-15/16 2-15/16 6-13/16 5 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 3/4 2-11/16 3-1/16 3-1/16 6-15/16 6 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-5/8 2-3/8 5/8 1-5/8 3/4 2-15/16 3-5/16 3-5/16 7-3/16 7 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5-1/8 2-7/8 5/8 1-5/8 3/4 2-15/16 3-5/16 3-5/16 7-3/16 1(Std.) 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-1/2 1-5/16 1/4 7/8 7/8 2-5/16 2-13/16 2-13/16 7-1/16 2 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 7/8 2-15/16 3-7/16 3-7/16 7-11/16 3 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/8 1-11/16 3/8 1-1/8 7/8 2-9/16 3-1/16 3-1/16 7-5/16 6 4 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 7/8 2-11/16 3-3/16 3-3/16 7-7/16 5 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 7/8 2-15/16 3-7/16 3-7/16 7-11/16 6 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 7/8 2-15/16 3-7/16 3-7/16 7-11/16 7 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 7/8 2-15/16 3-7/16 3-7/16 7-11/16 Parker Hannifin Corporation B155 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 1" to 6" Bore Sizes Series 2A C052 Head Trunnion Style D ZB + STROKE (NFPA Style MT1) Y P + STROKE LB + STROKE W UT EE 1 1 R 8 E 4 2 TD MM 3 J K F G TL E TL XG Cap Trunnion ZB + STROKE Style DB Y P + STROKE (NFPA Style MT2) LB + STROKE W UT EE 1 1 R 8 E 4 2 TD MM 3 J K F G TL E TL XJ + STROKE Intermediate Fixed Trunnion ZB + STROKE Style DD Y P + STROKE LB + STROKE (NFPA Style MT4) W UM EE 1 BD 1 R 8 UV E 4 2 TD MM J K 3 F G E XI** TM TL TL Rod End Dimensions — see table 2 Thread Style 4 Thread Style 8 Thread Style 9 “Special” Thread (NFPA Style SM) (NFPA Style IM) (NFPA Style SF) Style 3 Small Male Intermediate Male Small Female Special thread, LA LA A extension, rod eye, A W A W blank, etc., are also 1/8 C V C V KK CC KK available. To order, specify “Style 3” and give MM B MM B MM B desired dimensions D WRENCH FLATS for CC or KK, A NA NA NA D WRENCH D WRENCH 1/8 1/8 FLATS FLATS C V and LA. If otherwise W special, furnish A high strength rod end stud is supplied on thread style 4 through style 4 rod ends are recommended through 2" piston rod diameters dimensioned sketch. and style 8 rod ends are recommended on larger diameters. Use 2" diameter rods. Larger sizes or special rod ends are cut threads. Style 4 rod ends are recommended where the workpiece is secured style 9 for applications where female rod end threads are required. against the rod shoulder. When the workpiece is not shouldered, If rod end is not specified, style 4 will be supplied. Parker Hannifin Corporation B156 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 1" to 6" Bore Sizes Series 2A C052 Table 1—Envelope and Mounting Dimensions Add Stroke Style +.000 DD EE -.002 Min. Bore BD E NPTF F G J K TD TL TM UM UT UV LB P Stroke 1* • 1/4 3/8 1-1/2 1 3/16 .750• 3/4• • • 3 • 3-7/8 2-1/8 • n 1-1/2 1-1/4 2 3/8** 3/8 1-1/2 1 1/4 1.000 1 2-1/2 4-1/2 4 2-1/2 4 2-1/4 1/4 2 1-1/2 2-1/2 3/8** 3/8 1-1/2 1 5/16 1.000 1 3 5 4-1/2 3 4 2-1/4 1/2 2-1/2 1-1/2 3 3/8** 3/8 1-1/2 1 5/16 1.000 1 3-1/2 5-1/2 5 3-1/2 4-1/8 2-3/8 3/8 3-1/4 2 3-3/4 1/2 5/8 1-3/4 1-1/4 3/8 1.000 1 4-1/2 6-1/2 5-3/4 4-1/4 4-7/8 2-5/8 7/8 4 2 4-1/2 1/2 5/8 1-3/4 1-1/4 3/8 1.000 1 5-1/4 7-1/4 6-1/2 5 4-7/8 2-5/8 7/8 5 2 5-1/2 1/2 5/8 1-3/4 1-1/4 7/16 1.000 1 6-1/4 8-1/4 7-1/2 6 5-1/8 2-7/8 5/8 6 2-1/2 6-1/2 3/4 3/4 2 1-1/2 7/16 1.375 1-3/8 7-5/8 10-3/8 9-1/4 7 5-3/4 3-1/8 1-1/8 * Cushions not available on 1" bore. ** On 1", 1-1/2", 2" and 2-1/2" bore sizes, the head-end (only) pipe thread is not full depth on cylinders with No. 2 rods. Minimum of three full threads available. • Mounting style not available in 1" bore. n 1" bore head dimension is 1-3/4" x 1-1/2". See page B183. Table 3 — Envelope and Table 2—Rod Dimensions Mounting Dimensions Thread Rod Extensions and Pilot Dimensions Add Stroke Rod Style Style +.000 Rod Dia. 8 4 & 9 -.002 Min.** Bore No. MM CC KK A B C D LA NA V W XG Xi Y XJ ZB 1(Std.) 1/2 7/16-20 5/16-24 5/8 .999 3/8 3/8 1-1/4 7/16 1/4 5/8 1-3/4 * 1-15/16 4 4-11/16 1 2 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1-3/4 * 1-15/16 4 4-11/16 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1-3/4 3-3/16 1-15/16 4-1/8 4-7/8 1-1/2 2 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 2-1/8 3-9/16 2-5/16 4-1/2 5-1/4 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1-3/4 3-5/16 1-15/16 4-1/8 4-15/16 2-3/8 3-15/16 2-9/16 4-3/4 5-9/16 2 2 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-7/8 1-5/16 5/8 1-1/4 3 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 2-1/8 3-11/16 2-5/16 4-1/2 5-5/16 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1-3/4 3-5/16 1-15/16 4-1/4 5-1/16 2 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/2 1-11/16 3/4 1-1/2 2-5/8 4-3/16 2-13/16 5-1/8 5-15/16 2-1/2 3 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 2-1/8 3-11/16 2-5/16 4-5/8 5-7/16 4 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-7/8 1-5/16 5/8 1-1/4 2-3/8 3-15/16 2-9/16 4-7/8 5-11/16 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 2-1/4 4-3/16 2-7/16 5 6 2 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 2-7/8 4-13/16 3-1/16 5-5/8 6-5/8 3-1/4 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 2-1/2 4-7/16 2-11/16 5-1/4 6-1/4 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 2-3/4 4-11/16 2-15/16 5-1/2 6-1/2 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 2-1/4 4-3/16 2-7/16 5 6 2 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-5/8 2-3/8 5/8 1-5/8 3-1/8 5-1/16 3-5/16 5-7/8 6-7/8 4 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 2-1/2 4-7/16 2-11/16 5-1/4 6-1/4 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 2-3/4 4-11/16 2-15/16 5-1/2 6-1/2 5 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 2-7/8 4-13/16 3-1/16 5-5/8 6-5/8 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 2-1/4 4-5/16 2-7/16 5-1/4 6-5/16 2 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5-1/8 3-3/8 5/8 1-5/8 3-1/8 5-1/16 3-5/16 6-1/8 7-3/16 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 2-1/2 4-7/16 2-11/16 5-1/2 6-9/16 5 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 2-3/4 4-11/16 2-15/16 5-3/4 6-13/16 5 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 2-7/8 413/16 3-1/16 5-7/8 6-15/16 6 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-5/8 2-3/8 5/8 1-5/8 3-1/8 5-1/16 3-5/16 6-1/8 7-3/16 7 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5-1/8 2-7/8 5/8 1-5/8 3-1/8 5-1/16 3-5/16 6-1/8 7-3/16 1(Std.) 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-1/2 1-5/16 1/4 7/8 2-5/8 4-15/16 2-13/16 5-7/8 7-1/16 2 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 3-1/4 5-9/16 3-7/16 6-1/2 7-11/16 3 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/8 1-11/16 3/8 1-1/8 2-7/8 5-3/16 3-1/16 6-1/8 7-5/16 6 4 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 3 5-5/16 3-3/16 6-1/4 7-7/16 5 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 3-1/4 5-9/16 3-7/16 6-1/2 7-11/16 6 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 3-1/4 5-9/16 3-7/16 6-1/2 7-11/16 7 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 3-1/4 5-9/16 3-7/16 6-1/2 7-11/16 * Mounting style DD not available in 1" bore. **Dimension XI to be specified by customer. Parker Hannifin Corporation B157 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 1" to 6" Bore Sizes Series 2A C052 Cap Fixed Clevis Style BB (NFPA Style MP1) ZC + STROKE PIVOT PIN HARD CHROME PLATED Y P + STROKE LB + STROKE W E EE CD 1 MM 2 4 E MR LR K 3 G J L M F CW CB CW XC + STROKE The 1", 4", 5" and 6" bore sizes have tie rod nuts at both ends as shown. Tie rods thread into cap on all other bore sizes. Rod End Dimensions — see table 2 Thread Style 4 Thread Style 8 Thread Style 9 “Special” Thread (NFPA Style SM) (NFPA Style IM) (NFPA Style SF) Style 3 Small Male Intermediate Male Small Female Special thread, LA LA extension, rod eye, A A W A W blank, etc., are also 1/8 V V C C KK CC available. KK To order, specify “Style 3” and give MM B MM B MM B desired dimensions D WRENCH for CC or KK, A FLATS NA NA NA D WRENCH D WRENCH 1/8 1/8 and LA. If otherwise FLATS FLATS C V W special, furnish dimensioned sketch. style 4 rod ends are recommended through 2" piston rod diameters A high strength rod end stud is supplied on thread style 4 through 2" diameter rods. Larger sizes or special rod ends are cut threads. and style 8 rod ends are recommended on larger diameters. Use Style 4 rod ends are recommended where the workpiece is secured style 9 for applications where female rod end threads are required. against the rod shoulder. When the workpiece is not shouldered, If rod end is not specified, style 4 will be supplied. Parker Hannifin Corporation B158 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 1" to 6" Bore Sizes Series 2A C052 Table 1—Envelope and Mounting Dimensions +.000 Add Stroke -.002 EE Bore CB CD CW E NPTF F G J K L LR M MR LB P † † † † † † 1* .441 † n 1/4 3/8 1-1/2 1 3/16 1/2 1/2 7/16 1/2 3-7/8 2-1/8 1-1/2 3/4 .501 2 3/8** 3/8 1-1/2 1 1/4 1/2 5/8 4 2-1/4 1/2 3/4 3/4 2 3/4 .501 1/2 2-1/2 3/8** 3/8 1-1/2 1 5/16 3/4 3/4 1/2 5/8 4 2-1/4 2-1/2 3/4 .501 3 3/8** 3/8 1-1/2 1 5/16 1/2 5/8 4-1/8 2-3/8 1/2 3/4 3/4 3-1/4 1-1/4 .751 3-3/4 1/2 5/8 1-3/4 1-1/4 3/8 3/4 15/16 4-7/8 2-5/8 5/8 1-1/4 1 4 1-1/4 .751 5/8 4-1/2 1/2 5/8 1-3/4 1-1/4 3/8 1-1/4 1 3/4 15/16 4-7/8 2-5/8 5 1-1/4 .751 5-1/2 1/2 5/8 1-3/4 1-1/4 7/16 3/4 15/16 5-1/8 2-7/8 5/8 1-1/4 1 6 1-1/2 1.001 3/4 6-1/2 3/4 3/4 2 1-1/2 7/16 1-1/2 1-1/4 1 1-3/16 5-3/4 3-1/8 * Cushions not available on 1" bore. ** On 1", 1-1/2", 2" and 2-1/2" bore sizes, the head-end (only) pipe thread is not full depth on cylinders with No. 2 rods. Minimum of three full threads available. † In 1" bore size model only, a single eye mounting, 7/16" thick, is used. Dimension CD (.441") is hole diameter – pin not supplied. • Dimension CD is pin diameter except in 1" bore. n 1" bore head dimension is 1-3/4" x 1-1/2". See page B183 . Table 3 — Envelope and Table 2—Rod Dimensions Mounting Dimensions Thread Rod Extensions and Pilot Dimensions Add Stroke Rod Style Style +.000 Rod Dia. 8 4 & 9 -.002 Bore No. MM CC KK A B C D LA NA V W Y XC ZC 1(Std.) 1/2 7/16-20 5/16-24 5/8 .999 3/8 3/8 1-1/4 7/16 1/4 5/8 1-15/16 5 5-7/16 1 2 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1-15/16 5 5-7/16 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1-15/16 5-3/8 5-7/8 1-1/2 2 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 2-5/16 5-3/4 6-1/4 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1-15/16 5-3/8 5-7/8 2 2 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-7/8 1-5/16 5/8 1-1/4 2-9/16 6 6-1/2 3 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 2-5/16 5-3/4 6-1/4 1(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1-3/8 9/16 1/4 5/8 1-15/16 5-1/2 6 2 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/2 1-11/16 3/4 1-1/2 2-13/16 6-3/8 6-7/8 2-1/2 3 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 2-1/8 15/16 1/2 1 2-5/16 5-7/8 6-3/8 4 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-7/8 1-5/16 5/8 1-1/4 2-9/16 6-1/8 6-5/8 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 2-7/16 6-7/8 7-5/8 2 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 3-1/16 7-1/2 8-1/4 3-1/4 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 2-11/16 7-1/8 7-7/8 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 2-15/16 7-3/8 8-1/8 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 2-7/16 6-7/8 7-5/8 2 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-5/8 2-3/8 5/8 1-5/8 3-5/16 7-3/4 8-1/2 4 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 2-11/16 7-1/8 7-7/8 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 2-15/16 7-3/8 8-1/8 5 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 3-1/16 7-1/2 8-1/4 1(Std.) 1 7/8-14 3/4-16 1-1/8 1.499 1/2 7/8 1-7/8 15/16 1/4 3/4 2-7/16 7-1/8 7-7/8 2 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5-1/8 3-3/8 5/8 1-5/8 3-5/16 8 8-3/4 3 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-5/8 1-5/16 3/8 1 2-11/16 7-3/8 8-1/8 5 4 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/4 1-11/16 1/2 1-1/4 2-15/16 7-5/8 8-3/8 5 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-5/8 1-15/16 1/2 1-3/8 3-1/16 7-3/4 8-1/2 6 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-5/8 2-3/8 5/8 1-5/8 3-5/16 8 8-3/4 7 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5-1/8 2-7/8 5/8 1-5/8 3-5/16 8 8-3/4 1(Std.) 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-1/2 1-5/16 1/4 7/8 2-13/16 8-1/8 9-1/8 2 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 3-7/16 8-3/4 9-3/4 3 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/8 1-11/16 3/8 1-1/8 3-1/16 8-3/8 9-3/8 6 4 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 3-3/16 8-1/2 9-1/2 5 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 3-7/16 8-3/4 9-3/4 6 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 3-7/16 8-3/4 9-3/4 7 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 3-7/16 8-3/4 9-3/4 Parker Hannifin Corporation B159 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 7" Bore Sizes Series 2A/2AN C052 Tie Rods Extended ZB + STROKE Y P + STROKE Style TB (NFPA MX3) Style TB Head Tie Rods Extended, W LB + STROKE E EE illustrated: Style TC (NFPA (NFPA Style MX3) MX2), Cap Tie Rods 1 Extended; and Style TD (NFPA MX1), Both Ends Tie Rods Extended are also available. All “T” styles can be dimensioned from Style TB AA drawing at right. E 4 2 R MM DD 3 SQ. F G J K TT WF R BB ZB + STROKE Head Square Flange Y P + STROKE W LB + STROKE Style JB E EE 1 (NFPA Style ME3) MM E 4 2 TE 3 G J K SQ. F TT EB WF 4 HOLES TE ZJ + STROKE Cap Square Flange Y P + STROKE Style HB W LB + STROKE EE E (NFPA Style ME4) 1 MM TE 2 4 E K 3 F G J EB TE XK + STROKE 4 HOLES Rod End Dimensions — see table 2 Thread Style 4 Thread Style 8 Thread Style 9 (NFPA Style SM) (NFPA Style IM) (NFPA Style SF) “Special” Thread Small Male Intermediate Male Small Female LA LA Style 3 A A W A W 1/8 V V C C KK CC KK LA LA Special thread, A A W A W MM B MM B MM B extension, rod eye, 1/8 C V C V D WRENCH FLATS NA NA NA blank, etc., are also D WRENCH KK D WRENCH CC KK FLATS 1/8 FLATS1/8 C V W available. To order, specify MM B MM B MM B “Style 3” and give D WRENCH desired dimensions FLATS NA NA NA D WRENCH D WRENCH for CC or KK, A 1/8 1/8 FLATS FLATS C V W and LA. If otherwise special, furnish A high strength rod end stud is supplied on thread style 4 through 2" ends are recommended through 2" piston rod diameters and style diameter rods. Larger sizes or special rod ends are cut threads. Style 8 rod ends are recommended on larger diameters. Use style 9 for dimensional sketch. 4 rod ends are recommended where the workpiece is secured against applications where female rod end threads are required. If rod end is the rod shoulder. When the workpiece is not shouldered, style 4 rod not specified, style 4 will be supplied. Parker Hannifin Corporation B160 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 7" Bore Sizes Series 2A/2AN C052 Side Lug Side Tapped Style C Style F (NFPA Style MS2) (NFPA Style MS4) ZB + STROKE ZB + STROKE Y P + STROKE Y P + STROKE W LB + STROKE E W LB + STROKE US EE SQ. EE TT 1 1 E 2 MM E 4 2 MM 4 E Ð.005 E Ð.005 2 Ð.010 2 Ð.010 ST 3 3 G J K SQ. F TT SB F G J K SU SU 4 HOLES SW SW TN E XT SN + STROKE SW SW NT THREAD, ND DEEP XS SS + STROKE 4 TAPPED MTG. HOLES TS SW SW Cap Trunnion Head Trunnion Style DB Style D (NFPA Style MT2) (NFPA Style MT1) ZB + STROKE ZB + STROKE Y P + STROKE Y P + STROKE W LB + STROKE W LB + STROKE UT EE UT EE 1 1 1 1 R R 8 8 E 4 2 TD MM E 4 2 TD MM 3 3 G J K SQ. F F G J K TT SQ. TT XJ + STROKE XG TL E TL TL E TL ZC + STROKE Cap Fixed Clevis PIVOT PIN Y P + STROKE E W LB + STROKE Style BB EE 1 (NFPA Style MP1) CD MM E 2 4 MR LR K 3 F G J L M CW CB CW XC + STROKE Note: Other mounting styles and double rod end cylinders are available on request. Consult factory for details. Table 1—Envelope and Mounting Dimensions +.000 +.000 Add Stroke -.002 -.002 Bore AA BB CB CD CW DD E EB EE F G J K L LR M MR ND NT R SB ST SU SW TD TE TL TN TS US UT LB P SN SS 7 8.1 2-5/16 1-1/2 1.001 3/4 5/8-18 7-1/2 9/16 3/4 3/4 2 1-1/2 9/16 1-1/2 1-1/4 1 1-3/16 1-1/8 3/4-10 5.73 13/16 1 1-9/16 11/16 1.375 6-3/4 1-3/8 3-1/2 8-7/8 10-1/4 10-1/4 5-7/8 3-1/4 3-1/4 3-3/4 Table 3 — Envelope and Table 2—Rod Dimensions Mounting Dimensions Thread Rod Extensions and Pilot Dimensions Add Stroke Rod Style Style +.000 Rod Dia. 8 4 & 9 -.002 Bore No. MM CC KK A B C D LA NA V W WF Y TT XG XS XT XC XJ XK ZB ZC ZJ 1 1-35/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-1/2 1-5/16 1/4 7/8 1-5/8 2-13/16 4 2-5/8 2-5/16 2-13/16 8-1/4 6 5-1/4 7-5/16 9-1/4 6-3/4 7 2 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/48 1-1/2 3-1/8 1-115/16 3/8 1-1/8 1-7/8 3-1/16 4 2-7/8 2-9/16 3-1/16 8-1/2 6-1/4 5-1/2 7-9/16 9-1/2 7 3 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 1/2 1-1/4 2 3-3/16 4 3 2-11/16 3-3/16 8-5/8 6-3/8 5-5/8 7-11/16 9-5/8 7-1/8 Parker Hannifin Corporation B161 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 8" to 14" Bore Sizes Series 2A/2AN C052 Style TB (NFPA Tie Rods Extended MX3) Head Tie Rods ZB + STROKE Style TB Extended, illustrated: Y P + STROKE Style TC (NFPA MX2), W LB + STROKE (NFPA Style MX3) Cap Tie Rods Extended; E EE and Style TD (NFPA 1 MX1), Both Ends Tie Rods Extended are also available. All “T” styles can be dimensioned AA from Style TB drawing at right. E 4 2 R MM DD Mounting 3 styles TB & F G J K SQ. TT TD not offered WF R in 8" bore, rod BB codes #2, 9 and 0. ZB + STROKE Head Square Flange Y P + STROKE W LB + STROKE Style JB EE E 1 (NFPA Style ME3) E 2 TE MM 4 3 K SQ. F G J TT EB WF 4 HOLES TE ZJ + STROKE Cap Square Flange Y P + STROKE W Style HB LB + STROKE EE E 1 (NFPA Style ME4) MM TE 2 4 E K 3 G J F EB TE XK + STROKE 4 HOLES Rod End Dimensions — see table 2 Thread Style 4 Thread Style 8 Thread Style 9 (NFPA Style SM) (NFPA Style IM) (NFPA Style SF) “Special” Thread Small Male Intermediate Male Small Female Style 3 LA LA Special thread, A A W A W extension, rod eye, 1/8 C V C V KK CC blank, etc., are also KK available. To order, specify MM B MM B MM B “Style 3” and give D WRENCH desired dimensions FLATS NA NA NA D WRENCH D WRENCH 1/8 1/8 for CC or KK, A FLATS FLATS C V W and LA. If otherwise ends are recommended through 2" piston rod diameters and style A high strength rod end stud is supplied on thread style 4 through 2" special, furnish 8 rod ends are recommended on larger diameters. Use style 9 for diameter rods. Larger sizes or special rod ends are cut threads. Style dimensional sketch. applications where female rod end threads are required. If rod end is 4 rod ends are recommended where the workpiece is secured against not specified, style 4 will be supplied. the rod shoulder. When the workpiece is not shouldered, style 4 rod Parker Hannifin Corporation B162 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 8" to 14" Bore Sizes Series 2A/2AN C052 Table 1—Envelope and Mounting Dimensions Add Stroke EE Bore AA BB DD E EB NPTF F G J K R TE LB P 8 9.1 2-5/16 5/8-18 8-1/2 11/16 3/4 3/4 2 1-1/2 9/16 6.44 7.57 5-7/8 3-1/4 10 11.2 2-11/16 3/4-16 10-5/8 13/16 1 3/4 2-1/4 2 11/16 7.92 9.40 7-1/8 4-1/8 12 13.3 2-11/16 3/4-16 12-3/4 13/16 1 3/4 2-1/4 2 11/16 9.40 11.10 7-5/8 4-5/8 14 15.4 3-3/16 7/8-14 14-3/4 15/16 1-1/4 3/4 2-3/4 2-1/4 3/4 10.90 12.87 8-7/8 5-1/2 Table 3 — Envelope and Table 2—Rod Dimensions Mounting Dimensions Thread Rod Extensions and Pilot Dimensions Add Stroke Rod Style Style +.000 Rod Dia. 8 4 & 9 -.002 Bore No. MM CC KK A B C D LA NA V W TT WF Y XK ZB ZJ 1(Std.) 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-1/2 1-5/16 1/4 7/8 4 1-5/8 2-13/16 5-1/4 7-5/16 6-3/4 2 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 2-1/4 3-7/16 5-7/8 715/16 7-3/8 3 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/8 1-11/16 3/8 1-1/8 4 1-7/8 3-1/16 5-1/2 7-9/16 7 4 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 4 2 3-3/16 5-5/8 7-11/16 7-1/8 5 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 2-1/4 3-7/16 5-7/8 7-15/16 7-3/8 8 6 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 2-1/4 3-7/16 5-7/8 7-15/16 7-3/8 7 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 2-1/4 3-7/16 5-7/8 7-15/16 7-3/8 8 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 2-1/4 3-7/16 5-7/8 7-15/16 7-3/8 9 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 2-1/4 3-7/16 5-7/8 7-15/16 7-3/8 0 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 2-1/4 3-7/16 5-7/8 7-15/16 7-3/8 1(Std.) 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/8 1-11/16 3/8 1-1/8 4 1-7/8 3-1/8 6-1/4 8-15/16 8-1/4 3 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 4 2 3-1/4 6-3/8 9-1/16 8-3/8 4 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 2-1/4 3-1/2 6-5/8 9-5/16 8-5/8 5 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 2-1/4 3-1/2 6-5/8 9-5/16 8-5/8 10 6 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 2-1/4 3-1/2 6-5/8 9-5/16 8-5/8 7 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 2-1/4 3-1/2 6-5/8 9-5/16 8-5/8 8 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 2-1/4 3-1/2 6-5/8 9-5/16 8-5/8 9 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 2-1/4 3-1/2 6-5/8 9-5/16 8-5/8 0 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 2-1/4 3-1/2 6-5/8 9-5/16 8-5/8 1(Std.) 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 4 2 3-1/4 6-7/8 9-9/16 8-7/8 3 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 2-1/4 3-1/2 7-1/8 9-13/16 9-1/8 4 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 2-1/4 3-1/2 7-1/8 9-13/16 9-1/8 5 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 2-1/4 3-1/2 7-1/8 9-13/16 9-1/8 12 6 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 2-1/4 3-1/2 7-1/8 9-13/16 9-1/8 7 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 2-1/4 3-1/2 7-1/8 9-13/16 9-1/8 8 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 2-1/4 3-1/2 7-1/8 9-13/16 9-1/8 9 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 53/8 1/2 1-1/2 7 2-1/4 3-1/2 7-1/8 9-13/16 9-1/8 1(Std.) 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 2-1/4 3-13/16 8-1/8 11-1/8 10-3/8 3 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 2-1/4 3-13/16 8-1/8 11-1/8 10-3/8 4 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 2-1/4 3-13/16 8-1/8 11-1/8 10-3/8 14 5 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 2-1/4 3-13/16 8-1/8 11-1/8 10-3/8 6 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 2-1/4 3-13/16 8-1/8 11-1/8 10-3/8 7 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 2-1/4 3-13/16 8-1/8 11-1/8 10-3/8 8 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 2-1/4 3-13/16 8-1/8 11-1/8 10-3/8 Parker Hannifin Corporation B163 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 8" to 14" Bore Sizes Series 2A/2AN C052 Side Lug Style C (NFPA Style MS2) ZB + STROKE Y P + STROKE W LB + STROKE EE US 1 E 2 MM 4 E Ð.005 2 Ð.010 ST 3 F G J K SQ. TT SB SW SU SU SW 4 HOLES SW E SW XS SS + STROKE SW TS SW Rod End Dimensions — see table 2 Thread Style 4 Thread Style 9 Thread Style 8 (NFPA Style SM) (NFPA Style SF) (NFPA Style IM) “Special” Thread Small Male Small Female Intermediate Male LA LA Style 3 A A W A W 1/8 C V C V KK CC KK LA LA Special thread, A A W A W MM B MM B MM B extension, rod eye, 1/8 V V C D WRENCH C NA NA FLATS NA blank, etc., are also D WRENCH KK D WRENCH CC KK FLATS 1/8 FLATS1/8 C V W available. To order, specify MM B MM B MM B “Style 3” and give D WRENCH desired dimensions FLATS NA NA NA D WRENCH D WRENCH for CC or KK, A 1/8 1/8 C FLATS FLATS V W and LA. If otherwise special, furnish dimensional sketch. A high strength rod end stud is supplied on thread style 4 through 2" ends are recommended through 2" piston rod diameters and style diameter rods. Larger sizes or special rod ends are cut threads. Style 8 rod ends are recommended on larger diameters. Use style 9 for 4 rod ends are recommended where the workpiece is secured against applications where female rod end threads are required. If rod end is the rod shoulder. When the workpiece is not shouldered, style 4 rod not specified, style 4 will be supplied. Parker Hannifin Corporation B164 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 8" to 14" Bore Sizes Series 2A/2AN C052 Table 1—Envelope and Mounting Dimensions Add Stroke EE Bore E NPTF F G J K SB* ST SU SW TS US LB P SS 8 8-1/2 3/4 3/4 2 1-1/2 9/16 13/16 1 1-9/16 11/16 9-7/8 11-1/4 5-7/8 3-1/4 3-3/4 10 10-5/8 1 3/4 2-1/4 2 11/16 1-1/16 1-1/4 2 7/8 12-3/8 14-1/8 7-1/8 4-1/8 4-5/8 12 12-3/4 1 3/4 2-1/4 2 11/16 1-1/16 1-1/4 2 7/8 14-1/2 16-1/4 7-5/8 4-5/8 5-1/8 14 14-3/4 1-1/4 3/4 2-3/4 2-1/4 3/4 1-5/16 1-1/2 2-1/2 1-1/8 17 19-1/4 8-7/8 5-1/2 5-7/8 * Upper surface spotfaced for socket head screws. Table 3 — Envelope and Table 2—Rod Dimensions Mounting Dimensions Add Thread Rod Extensions and Pilot Dimensions Stroke Rod Style Style +.000 Rod Dia. 8 4 & 9 -.002 Bore No. MM CC KK A B C D LA NA V W TT XS Y ZB 1(Std.) 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-1/2 1-5/16 1/4 7/8 4 2-5/16 2-13/16 7-5/16 2 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 53/8 1/2 1-1/2 7 2-15/16 3-7/16 7-15/16 3 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/8 1-11/16 3/8 1-1/8 4 2-9/16 3-1/16 7-9/16 4 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 4 2-11/16 3-3/16 7-11/16 5 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 2-15/16 3-7/16 7-15/16 8 6 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 2-15/16 3-7/16 7-15/16 7 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 2-15/16 3-7/16 7-15/16 8 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 2-15/16 3-7/16 7-15/16 9 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 2-15/16 3-7/16 7-15/16 0 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 2-15/16 3-7/16 7-15/16 1(Std.) 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/8 1-11/16 3/8 1-1/8 4 2-3/4 3-1/8 8-15/16 3 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 4 2-7/8 3-1/4 9-1/16 4 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-1/8 3-1/2 9-5/16 5 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-1/8 3-1/2 9-5/16 10 6 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-1/8 3-1/2 9-5/16 7 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-1/8 3-1/2 9-5/16 8 4-1/2 4-1/4-12 3-1/4-12 41/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 3-1/8 3-1/2 9-5/16 9 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 61/2 4-7/8 1/2 1-1/2 7 3-1/8 3-1/2 9-5/16 0 5--1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 3-1/8 3-1/2 9-5/16 1(Std.) 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-1/16 3-1/2 1-15/16 3/8 1-1/4 4 2-7/8 3-1/4 9-9/16 3 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-1/8 3-1/2 9-13/16 4 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-1/8 3-1/2 9-13/16 5 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-1/8 3-1/2 9-13/16 12 6 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-1/8 3-1/2 9-13/16 7 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 3-1/8 3-1/2 9-13/16 8 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 3-1/8 3-1/2 9-13/16 9 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 3-1/8 3-1/2 9-13/16 1(Std.) 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-3/8 3-13/16 11-1/8 3 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-3/8 3-13/16 11-1/8 4 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-3/8 3-13/16 11-1/8 14 5 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-3/8 3-13/16 11-1/8 6 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 3-3/8 3-13/16 11-1/8 7 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 3-3/8 3-13/16 11-1/8 8 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 3-3/8 3-13/16 11-1/8 Parker Hannifin Corporation B165 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 8" to 14" Bore Sizes Series 2A/2AN C052 Side Tapped Style F (NFPA Style MS4) ZB + STROKE Y P + STROKE E W LB + STROKE SQ. EE TT 1 MM E 4 2 E Ð.005 2 Ð.010 3 K F G J TN XT SN + STROKE NT THREAD, ND DEEP 4 TAPPED MTG. HOLES Rod End Dimensions — see table 2 Thread Style 4 Thread Style 8 Thread Style 9 (NFPA Style SM) (NFPA Style IM) (NFPA Style SF) “Special” Thread Small Male Intermediate Male Small Female LA LA A Style 3 A W A W 1/8 C V C V KK CC KK LA LA Special thread, A A W A W MM B MM B MM B extension, rod eye, 1/8 C V C V D WRENCH NA NA FLATS NA blank, etc., are also D WRENCH KK D WRENCH CC KK 1/81/8 FLATS FLATS C V W available. To order, specify MM B MM B MM B “Style 3” and give D WRENCH desired dimensions NA NA FLATS NA D WRENCH D WRENCH for CC or KK, A 1/8 1/8 C FLATS FLATS V W and LA. If otherwise special, furnish dimensional sketch. A high strength rod end stud is supplied on thread style 4 through 2" ends are recommended through 2" piston rod diameters and style diameter rods. Larger sizes or special rod ends are cut threads. Style 8 rod ends are recommended on larger diameters. Use style 9 for 4 rod ends are recommended where the workpiece is secured against applications where female rod end threads are required. If rod end is the rod shoulder. When the workpiece is not shouldered, style 4 rod not specified, style 4 will be supplied. Parker Hannifin Corporation B166 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 8" to 14" Bore Sizes Series 2A/2AN C052 Table 1—Envelope and Mounting Dimensions Add Stroke EE Bore E NPTF F G J K ND NT R TN LB P SN 8 8-1/2 3/4 3/4 2 1-1/2 9/16 1-1/8 3/4-10 6.44 4-1/2 5-7/8 3-1/4 3-1/4 10 10-5/8 1 3/4 2-1/4 2 11/16 1-1/2 1-8 7.92 5-1/2 7-1/8 4-1/8 4-1/8 12 12-3/4 1 3/4 2-1/4 2 11/16 1-1/2 1-8 9.40 7-1/4 7-5/8 4-5/8 4-5/8 14 14-3/4 1-1/4 3/4 2-3/4 2-1/4 3/4 1-7/8 1-1/4-7 10.90 8-3/8 8-7/8 5-1/2 5-1/2 Table 3 — Envelope and Table 2—Rod Dimensions Mounting Dimensions Add Thread Rod Extensions and Pilot Dimensions Stroke Rod Style Style +.000 Rod Dia 8 4 & 9 -.002 Bore No. MM CC KK A B C D LA NA V W TT XT Y ZB 1(Std.) 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-1/2 1-5/16 1/4 7/8 4 2-13/16 2-13/16 7-5/16 2 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 3-7/16 3-7/16 7-15/16 3 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/8 1-11/16 3/8 1-1/8 4 3-1/16 3-1/16 7-9/16 4 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 4 3-3/16 3-3/16 7-11/16 5 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-7/16 3-7/16 7-15/16 8 6 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-7/16 3-7/16 7-15/16 7 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-7/16 3-7/16 7-15/16 8 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-7/16 3-7/16 7-15/16 9 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 3-7/16 3-7/16 7-15/16 0 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 3-7/16 3-7/16 7-15/16 1(Std.) 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/8 1-11/16 3/8 1-1/8 4 3-1/8 3-1/8 8-15/16 3 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1- 15/16 3/8 1-1/4 4 3-1/4 3-1/4 9-1/16 4 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-1/2 3-1/2 9-5/16 5 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-1/2 3-1/2 9-5/16 10 6 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-1/2 3-1/2 9-5/16 7 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-1/2 3-1/2 9-5/16 8 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 3-1/2 3-1/2 9-5/16 9 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 3-1/2 3-1/2 9-5/16 0 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 3-1/2 3-1/2 9-5/16 1(Std.) 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 4 3-1/4 3-1/4 9-9/16 3 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-1/2 3-1/2 9-13/16 4 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-1/2 3-1/2 9-13/16 5 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-1/2 3-1/2 9-13/16 12 6 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-1/2 3-1/2 9-13/16 7 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 11/2 7 3-1/2 3-1/2 9-13/16 8 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 3-1/2 3-1/2 9-13/16 9 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 3-1/2 3-1/2 9-13/16 1(Std.) 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-13/16 3-13/16 11-1/8 3 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-13/16 3-13/16 11-1/8 4 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-13/16 3-13/16 11-1/8 14 5 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-13/16 313/16 11-1/8 6 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 3-13/16 313/16 11-1/8 7 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 3-13/16 3-13/16 11-1/8 8 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 3-13/16 3-13/16 11-1/8 Parker Hannifin Corporation B167 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 8" to 14" Bore Sizes Series 2A/2AN C052 Cap Fixed Clevis Style BB (NFPA Style MP1) ZC + STROKE PIVOT PIN Y P + STROKE E W LB + STROKE EE 1 CD MM E 2 4 MR LR K 3 F G J L M CW CB CW XC + STROKE Rod End Dimensions — see table 2 Thread Style 4 Thread Style 8 Thread Style 9 (NFPA Style SM) (NFPA Style IM) (NFPA Style SF) “Special” Thread Small Male Intermediate Male Small Female LA LA A Style 3 A W A W 1/8 C V C V KK CC KK LA LA Special thread, A A W A W MM B MM B MM B extension, rod eye, 1/8 C V C V D WRENCH NA NA FLATS NA blank, etc., are also D WRENCH KK D WRENCH CC KK 1/81/8 FLATS FLATS C V W available. To order, specify MM B MM B MM B “Style 3” and give D WRENCH desired dimensions NA NA FLATS NA D WRENCH D WRENCH for CC or KK, A 1/8 1/8 C FLATS FLATS V W and LA. If otherwise special, furnish dimensional sketch. A high strength rod end stud is supplied on thread style 4 through 2" ends are recommended through 2" piston rod diameters and style diameter rods. Larger sizes or special rod ends are cut threads. Style 8 rod ends are recommended on larger diameters. Use style 9 for 4 rod ends are recommended where the workpiece is secured against applications where female rod end threads are required. If rod end is the rod shoulder. When the workpiece is not shouldered, style 4 rod not specified, style 4 will be supplied. Parker Hannifin Corporation B168 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 8" to 14" Bore Sizes Series 2A/2AN C052 Table 1—Envelope and Mounting Dimensions +.000 Add Stroke -.002 EE Bore CB CD* CW E NPTF F G J K L LR M MR LB P 8 1-1/2 1.001 3/4 8-1/2 3/4 3/4 2 1-1/2 9/16 1-1/2 1-1/4 1 1-3/16 5-7/8 3-1/4 10 2 1.376 1 10-5/8 1 3/4 2-1/4 2 1-1/16 2-1/8 1-7/8 1-3/8 1-5/8 7-1/8 4-1/8 12 2-1/2 1.751 1-1/4 12-3/4 1 3/4 2-1/4 2 1-1/16 2-1/4 2-1/8 1-3/4 2-1/8 7-5/8 4-5/8 14 2-1/2 2.001 1-1/4 14-3/4 1-1/4 3/4 2-3/4 2-1/4 3/4 2-1/2 2-3/8 2 2-3/8 8-7/8 5-1/2 * CD is pin diameter. Table 3 — Envelope and Table 2—Rod Dimensions Mounting Dimensions Thread Rod Extensions and Pilot Dimensions Add Stroke Rod Style Style Rod Dia. 8 4 & 9 +.000 Bore No. MM CC KK A -.002 B C D LA NA V W TT Y XC ZC 1(Std.) 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-1/2 1-5/16 1/4 7/8 4 2-13/16 8-1/4 9-1/4 2 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 3-7/16 8-7/8 9-7/8 3 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/8 11-1/16 3/8 1-1/8 4 3-1/16 8-1/2 9-1/2 4 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 11-5/16 3/8 1-1/4 4 3-3/16 8-5/8 9-5/8 5 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-7/16 8-7/8 9-7/8 8 6 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-7/16 8-7/8 9-7/8 7 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-7/16 8-7/8 9-7/8 8 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-7/16 8-7/8 9-7/8 9 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 3-7/16 8-7/8 9-7/8 0 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 3-7/16 8-7/8 9-7/8 1(Std.) 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/8 1-11/16 3/8 1-1/8 4 3-1/8 10-3/8 11-3/4 3 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 4 3-1/4 10-1/2 11-7/8 4 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-1/2 10-3/4 12-1/8 5 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-1/2 10-3/4 12-1/8 10 6 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-1/2 10-3/4 12-1/8 7 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-1/2 10-3/4 12-1/8 8 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 3-1/2 10-3/4 12-1/8 9 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 3-1/2 10-3/4 12-1/8 0 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 3-1/2 10-3/4 12-1/8 1(Std.) 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 4 3-1/4 11-1/8 12-7/8 3 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-1/2 11-3/8 13-1/8 4 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-1/2 11-3/8 13-1/8 5 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-1/2 11-3/8 13-1/8 12 6 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-1/2 11-3/8 13-1/8 7 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 3-1/2 11-3/8 13-1/8 8 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 3-1/2 11-3/8 13-1/8 9 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 3-1/2 11-3/8 13-1/8 1(Std.) 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-13/16 12-7/8 14-7/8 3 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-13/16 12-7/8 14-7/8 4 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-13/16 12-7/8 14-7/8 14 5 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-13/16 12-7/8 14-7/8 6 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 3-13/16 12-7/8 14-7/8 7 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 3-13/16 12-7/8 14-7/8 8 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 3-13/16 12-7/8 14-7/8 Parker Hannifin Corporation B169 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 8" to 14" Bore Sizes Series 2A/2AN C052 Head Trunnion ZB + STROKE Style D Y P + STROKE W LB + STROKE (NFPA Style MT1) EE UT 1 1 R 8 E 4 2 TD MM 3 F G J K SQ. TT XG TL E TL Cap Trunnion ZB + STROKE Y P + STROKE Style DB W LB + STROKE EE UT (NFPA Style MT2) 1 1 R 8 E 4 2 TD MM 3 F G J K SQ. TT XJ + STROKE TL E TL Intermediate Fixed Trunnion ZB + STROKE Style DD Y P + STROKE LB + STROKE W (NFPA Style MT4) EE UM BD 1 1 R 8 UV E 4 2 TD MM G J K F 3 SQ. TT XI** E TL TM TL Rod End Dimensions — see table 2 Thread Style 4 Thread Style 8 Thread Style 9 (NFPA Style SM) (NFPA Style IM) (NFPA Style SF) “Special” Thread Small Male Intermediate Male Small Female LA LA Style 3 A A W A W 1/8 V V C C KK CC KK LA LA Special thread, A A W A W MM B MM B MM B extension, rod eye, 1/8 C V C V D WRENCH FLATS NA NA NA blank, etc., are also D WRENCH KK D WRENCH CC KK FLATS 1/8 FLATS1/8 C V W available. To order, specify MM B MM B MM B “Style 3” and give D WRENCH desired dimensions FLATS NA NA NA D WRENCH D WRENCH for CC or KK, A 1/8 1/8 FLATS FLATS C V W and LA. If otherwise ends are recommended through 2" piston rod diameters and style A high strength rod end stud is supplied on thread style 4 through 2" special, furnish 8 rod ends are recommended on larger diameters. Use style 9 for diameter rods. Larger sizes or special rod ends are cut threads. Style dimensional sketch. applications where female rod end threads are required. If rod end is 4 rod ends are recommended where the workpiece is secured against not specified, style 4 will be supplied. the rod shoulder. When the workpiece is not shouldered, style 4 rod Parker Hannifin Corporation B170 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Mounting Information – 8" to 14" Bore Sizes Series 2A/2AN C052 Envelope and Mounting Dimensions Add Stroke Style +.000 DD EE -.001 Min. Bore BD E NPTF F G J K TD TL TM UM UT UV LB P Stroke 8 2-1/2 8-1/2 3/4 3/4 2 1-1/2 9/16 1.375 1-3/8 9-3/4 12-1/2 11-1/4 9-1/2 5-7/8 3-1/4 7/8 10 3 10-5/8 1 3/4 2-1/4 2 1-1/16 1.750 1-3/4 12 15-1/2 14-1/8 11-3/4 7-1/8 4-1/8 7/8 12 3 12-3/4 1 3/4 2-1/4 2 1-1/16 1.750 1-3/4 14 17-1/2 16-1/4 13-3/4 7-5/8 4-5/8 3/8 14 3-1/2 14-3/4 1-1/4 3/4 2-3/4 2-1/4 3/4 2.000 2 16-1/4 20-1/4 18-3/4 16 8-7/8 5-1/2 3/8 Table 3 — Envelope and Table 2—Rod Dimensions Mounting Dimensions Thread Rod Extensions and Pilot Dimensions Add Stroke Rod Style Style +.000 Rod Dia. 8 4 & 9 -.002 Min.** Bore No. MM CC KK A B C D LA NA V W TT XG XI Y XJ ZB 1(Std.) 1-3/8 1-1/4-12 1-14 1-5/8 1.999 5/8 1-1/8 2-1/2 1-5/16 1/4 7/8 4 2-5/8 4-15/16 2-13/16 6 7-5/16 2 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 3-1/4 5-9/16 3-7/16 6-5/8 7-15/16 3 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/8 1-1/2 3-1/8 1-11/16 3/8 1-1/8 4 2-7/8 5-3/16 3-1/16 6-1/4 7-9/16 4 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 4 3 5-5/16 3-3/16 6-3/8 7-11/16 5 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-1/4 5-9/16 3-7/16 6-5/8 7-15/16 8 6 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-1/4 5-3/16 3-7/16 6-5/8 7-15/16 7 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-1/4 5-9/16 3-7/16 6-5/8 7-15/16 8 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-1/4 5-9/16 3-7/16 6-5/8 7-15/16 9 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 3-1/4 5-9/16 3-7/16 6-5/8 7-15/16 0 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 3-1/4 5-9/16 3-7/16 6-5/8 7-15/16 1(Std.) 1-3/4 1-1/2-12 1-1/4-12 2 2.374 3/4 1-1/2 3-1/8 1-11/16 3/8 1-1/8 4 3 5-11/16 3-1/8 7-1/4 8-15/16 3 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 4 3-1/8 5-13/16 3-1/4 7-3/8 9-1/16 4 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-3/8 6-1/16 3-1/2 7-5/8 9-5/16 5 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-3/8 6-1/16 3-1/2 7-5/8 9-5/16 6 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-3/8 6-1/16 3-1/2 7-5/8 9-5/16 10 7 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-3/8 6-1/16 3-1/2 7-5/8 9-5/16 8 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 3-3/8 6-1/16 3-1/2 7-5/8 9-5/16 9 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 3-3/8 6-1/16 3-1/2 7-5/8 9-5/16 0 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 3-3/8 6-1/16 3-1/2 7-5/8 9-5/16 1(Std.) 2 1-3/4-12 1-1/2-12 2-1/4 2.624 7/8 1-11/16 3-1/2 1-15/16 3/8 1-1/4 4 3-1/8 5-13/16 3-1/4 7-7/8 9-9/16 3 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-3/8 6-1/16 3-1/2 8-1/8 9-13/16 4 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-3/8 6-1/16 3-1/2 8-1/8 9-13/16 5 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-3/8 6-1/16 3-1/2 8-1/8 9-13/16 12 6 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-3/8 6-1/16 3-1/2 8-1/8 9-13/16 7 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 3-3/8 6-1/16 3-1/2 8-1/8 9-13/16 8 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 3-3/8 6-1/16 3-1/2 8-1/8 9-13/16 9 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 33/8 6-1/16 3-1/2 8-1/8 9-13/16 1(Std.) 2-1/2 2-1/4-12 1-7/8-12 3 3.124 1 2-1/16 4-1/2 2-3/8 1/2 1-1/2 4 3-5/8 6-13/16 3-13/16 9-1/4 11-1/8 3 3 2-3/4-12 2-1/4-12 3-1/2 3.749 1 2-5/8 5 2-7/8 1/2 1-1/2 5-1/2 3-5/8 6-13/16 3-13/16 9-1/4 11-1/8 4 3-1/2 3-1/4-12 2-1/2-12 3-1/2 4.249 1 3 5 3-3/8 1/2 1-1/2 5-1/2 3-5/8 6-13/16 3-13/16 9-1/4 11-1/8 14 5 4 3-3/4-12 3-12 4 4.749 1 3-3/8 5-1/2 3-7/8 1/2 1-1/2 5-1/2 3-5/8 6-13/16 3-13/16 9-1/4 11-1/8 6 4-1/2 4-1/4-12 3-1/4-12 4-1/2 5.249 1 3-7/8 6 4-3/8 1/2 1-1/2 7 3-5/8 6-13/16 3-13/16 9-1/4 11-1/8 7 5 4-3/4-12 3-1/2-12 5 5.749 1 4-1/4 6-1/2 4-7/8 1/2 1-1/2 7 3-5/8 6-13/16 3-13/16 9-1/4 11-1/8 8 5-1/2 5-1/4-12 4-12 5-1/2 6.249 1 4-5/8 7 5-3/8 1/2 1-1/2 7 3-5/8 6-13/16 3-13/16 9-1/4 11-1/8 **Dimension XI to be specified by customer. Parker Hannifin Corporation B171 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Spherical Bearing Mounting Series 2A/2AN C052 Style SB – 1-1/2" to 6" Bore Sizes XL + STROKE CE ZC + STROKE LUBRICATION XC + STROKE MA FITTING LUBRICATION FITTING 1 1 KE ER 2 4 2 4 MS CD CD 3 3 W NR LE EX KK EX A Thread Add Stroke Max. Rod Oper. Style Style Rod Dia. PSI 9 7 Bore No. MM KK KK A W XC XL ZC KE CD* CE ER EX LE MA MS NR 2A 1(Std.) 5/8 7/16-20 — 3/4 5/8 5-3/8 6-1/4 6-1/8 1- 1/2 -.0005 1-1/2 7/8 13/16 7/16 3/4 3/4 15/16 5/8 250 .5000 2 1 ** 7/16-20 3/4 1 5-3/4 6-5/8 6-1/2 1-7/8 1(Std.) 5/8 7/16-20 — 3/4 5/8 5-3/8 6-1/4 6-1/8 1-1/2 -.0005 2 2 1-3/8 ** 7/16-20 3/4 1-1/4 6 6-7/8 6-3/4 2-1/8 7/8 13/16 7/16 3/4 3/4 15/16 5/8 250 .5000 3 1 ** 7/16-20 3/4 1 5-3/4 6-5/8 6-1/2 1-7/8 1(Std.) 5/8 7/16-20 — 3/4 5/8 5-1/2 6-3/8 6-1/4 1-1/2 2 1-3/4 ** 7/16-20 3/4 1-1/2 6-3/8 7-1/4 7-1/8 2-3/8 -.0005 2-1/2 7/8 13/16 7/16 3/4 3/4 15/16 5/8 250 3 1 ** 7/16-20 3/4 1 5-7/8 6-3/4 6-5/8 1-7/8 .5000 4 1-3/8 ** 7/16-20 3/4 1-1/4 6-1/8 7 6-7/8 2-1/8 1(Std.) 1 3/4-16 — 1-1/8 3/4 6-7/8 8-1/8 7-7/8 2 2 2 ** 3/4-16 1-1/8 1-3/8 7-1/2 8-3/4 8-1/2 2-5/8 -.0005 3-1/4 1-1/4 1-1/8 2-1/32 1-1/16 1 1-3/8 1 250 .7500 3 1-3/8 ** 3/4-16 1-1/8 1 7-1/8 8-3/8 8-1/8 2-1/4 4 1-3/4 ** 3/4-16 1-1/8 1-1/4 7-3/8 8-5/8 8-3/8 2-1/2 1(Std.) 1 3/4-16 — 1-1/8 3/4 6-7/8 8-1/8 7-7/8 2 2 2-1/2 ** 3/4-16 1-1/8 1-5/8 7-3/4 9 8-3/4 2-7/8 -.0005 4 3 1-3/8 ** 3/4-16 1-1/8 1 7-1/8 8-3/8 8-1/8 2-1/4 1-1/4 1-1/8 2-1/32 1-1/16 1 1-3/8 1 250 .7500 4 1-3/4 ** 3/4-16 1-1/8 1-1/4 7-3/8 8-5/8 8-3/8 2-1/2 5 2 ** 3/4-16 1-1/8 1-3/8 7-1/2 8-3/4 8-1/2 2-5/8 1(Std.) 1 3/4-16 — 1-1/8 3/4 7-1/8 8-3/8 8-1/8 2 2 3-1/2 ** 3/4-16 1-1/8 1-5/8 8 9-1/4 9 2-7/8 3 1-3/8 ** 3/4-16 1-1/8 1 7-3/8 8-5/8 8-3/8 2-1/4 -.0005 5 4 1-3/4 ** 3/4-16 1-1/8 1-1/4 7-5/8 8-7/8 8-5/8 2-1/2 1-1/4 1-1/8 2-1/32 1-1/16 1 1-3/8 1 250 .7500 5 2 ** 3/4-16 1-1/8 1-3/8 7-3/4 9 8-3/4 2-5/8 6 2-1/2 ** 3/4-16 1-1/8 1-5/8 8 9-1/4 9 2-7/8 7 3 ** 3/4-16 1-1/8 1-5/8 8 9-1/4 9 2-7/8 1(Std.) 1-3/8 1-14 — 1-5/8 7/8 8-1/8 10 9-3/8 2-3/4 2 4 ** 1-14 1-5/8 1-1/2 8-3/4 10-5/8 10 3-3/8 3 1-3/4 ** 1-14 1-5/8 1-1/8 8-3/8 10-1/4 9-5/8 3 -.0005 6 4 2 ** 1-14 1-5/8 1-1/4 8-1/2 10-3/8 9-3/4 3-1/8 1-7/8 1-1/4 7/8 1-7/16 1-1/4 1-11/16 1-1/4 250 1.0000 5 2-1/2 ** 1-14 1-5/8 1-1/2 8-3/4 10-5/8 10 3-3/8 6 3 ** 1-14 1-5/8 1-1/2 8-3/4 10-5/8 10 3-3/8 7 3-1/2 ** 1-14 1-5/8 1-1/2 8-3/4 10-5/8 10 3-3/8 Maximum operating pressure at 4:1 design factor is based on tensile strength of material. Pressure ratings are based on standard commercial bearing ratings. Note: For additional dimensions see Series 2A, page B158. * Dimension CD is hole diameter. ** Corresponding rod eye pin diameter may not match pin diameter of cap. Rod No. 1 is standard. Parker Hannifin Corporation B172 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Spherical Bearing Mounting Series 2A/2AN C052 Style SB – 8" to 14" Bore Sizes XL + STROKE ZC + STROKE CE LUBRICATION FITTING XC + STROKE MA LUBRICATION FITTING 1 1 KE ER 4 2 2 4 MS CD CD 3 3 W NR LE EX KK EX A Thread Add Stroke Max. Rod Style Style Oper. Rod Dia. 9 7 PSI Bore No. MM KK KK A W XC XL ZC KE CD* CE ER EX LE MA MS NR 2A 1(Std.) 1-3/8 1-14 – 1-5/8 7/8 8-1/4 10-1/8 9-1/2 2-3/4 2 5-1/2 ** 1-14 1-5/8 1-1/2 8-7/8 10-3/4 10-1/8 3-3/8 3 1-3/4 ** 1-14 1-5/8 1-1/8 8-1/2 10-3/8 9-3/4 3 4 2 ** 1-14 1-5/8 1-1/4 8-5/8 10-1/2 9-7/8 3-1/8 5 2-1/2 ** 1-14 1-5/8 1-1/2 8-7/8 10-3/4 10-1/8 3-3/8 -.0005 8 1-7/8 1-1/4 7/8 1-7/16 1-1/4 1-11/16 1-1/4 250 1.0000 6 3 ** 1-14 1-5/8 1-1/2 8-7/8 10-3/4 10-1/8 3-3/8 7 3-1/2 ** 1-14 1-5/8 1-1/2 8-7/8 10-3/4 10-1/8 3-3/8 8 4 ** 1-14 1-5/8 1-1/2 8-7/8 10-3/4 10-1/8 3-3/8 9 4-1/2 ** 1-14 1-5/8 1-1/2 8-7/8 10-3/4 10-1/8 3-3/8 0 5 ** 1-14 1-5/8 1-1/2 8-7/8 10-3/4 10-1/8 3-3/8 1(Std.) 1-3/4 1-1/4-12 – 2 1-1/8 10-3/8 12-1/2 12-1/4 3-1/4 3 2 ** 1-1/4-12 2 1-1/4 10-1/2 12-5/8 12-3/8 3-3/8 4 2-1/2 ** 1-1/4-12 2 1-1/2 10-3/4 12-7/8 12-5/8 3-5/8 5 3 ** 1-1/4-12 2 1-1/2 10-3/4 12-7/8 12-5/8 3-5/8 -.0005 10 6 3-1/2 ** 1-1/4-12 2 1-1/2 10-3/4 12-7/8 12-5/8 3-5/8 2-1/8 1-11/16 1-3/16 17/8 1-7/8 2-7/16 1-5/8 250 1.3750 7 4 ** 1-1/4-12 2 1-1/2 10-3/4 12-7/8 12-5/8 3-5/8 8 4-1/2 ** 1-1/4-12 2 1-1/2 10-3/4 12-7/8 12-5/8 3-5/8 9 5 ** 1-1/4-12 2 1-1/2 10-3/4 12-7/8 12-5/8 3-5/8 0 5-1/2 ** 1-1/4-12 2 1-1/2 10-3/4 12-7/8 12-5/8 3-5/8 1(Std.) 2 1-1/2-12 – 2-1/4 1-1/4 11-1/8 13-5/8 13-5/8 3-3/4 3 2-1/2 ** 1-1/2-12 2-1/4 1-1/2 11-3/8 13-7/8 13-7/8 4 4 3 ** 1-1/2-12 2-1/4 1-1/2 11-3/8 13-7/8 13-7/8 4 5 3-1/2 ** 1-1/2-12 21/4 1-1/2 11-3/8 13-7/8 13-7/8 4 -.0005 12 2-1/2 2-1/16 11-7/32 2-1/8 2-1/2 2-7/8 2-1/16 250 1.7500 6 4 ** 1-1/2-12 2-1/4 1-1/2 11-3/8 13-7/8 13-7/8 4 7 4-1/2 ** 1-1/2-12 2-1/4 1-1/2 11-3/8 13-7/8 137/8 4 8 5 ** 1-1/2-12 2-1/4 1-1/2 11-3/8 13-7/8 13-7/8 4 9 5-1/2 ** 1-1/2-12 2-1/4 1-1/2 11-3/8 13-7/8 13-7/8 4 1(Std.) 2-1/2 1-7/8-12 – 3 1-1/2 12-7/8 15-5/8 15-3/8 4-1/4 3 3 ** 1-7/8-12 3 1-1/2 12-7/8 15-5/8 15-3/8 4-1/4 4 3-1/2 ** 1-7/8-12 3 1-1/2 12-7/8 15-5/8 15-3/8 4-1/4 -.0005 5 4 ** 1-7/8-12 3 1-1/2 12-7/8 15-5/8 15-3/8 4-1/4 14 2-3/4 2-1/2 1-3/4 2-1/2 2-1/2 3-5/16 2-3/8 250 2.0000 6 4-1/2 ** 1-7/8-12 3 1-1/2 12-7/8 15-5/8 15-3/8 4-1/4 7 5 ** 1-7/8-12 3 1-1/2 12-7/8 15-5/8 15-3/8 4-1/4 8 5-1/2 ** 1-7/8-12 3 1-1/2 12-7/8 15-5/8 15-3/8 4-1/4 Maximum operating pressure at 4:1 design factor is based on tensile strength of material. Pressure ratings are based on standard commercial bearing ratings. Note: For additional dimensions see Series 2A, page B210. * Dimension CD is hole diameter. ** Corresponding rod eye pin diameter may not match pin diameter of cap. Rod No. 1 is standard. Parker Hannifin Corporation B173 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Double Rod Models – 1" to 14" Bore Sizes Series 2A/2AN C052 How to Use Double Rod Cylinder Dimensioned Drawings ZM + 2 X STROKE ZL + STROKE 1"- 6" Bores Y P + STROKE LD + STROKE W EE Rod Rod End End #1 #2 MM K G F G F ZM + 2 X STROKE 7"- 14" Bores Y P + STROKE W LD + STROKE EE Dimensions Shown on Mounting This Page Supplement Mounting Rod Rod Styles for Dimensions on Pages Styles for End End Corresponding Listed Below Single Rod #1 #2 Double Rod Models 1" - 6" 8" - 14" Models* MM Bores Bores T KT B192 B204 TB** KTB B192 B204 TD KTD B192 B204 K F G F J KJ B102 — WF G JB** KJB B194 B204 or are in addition to those for single rod To determine dimensions for a double rod cylinders shown on preceding pages cylinder, first refer to the desired single rod C** KC B196 B206 and provide the information needed mounting style cylinder shown on F KF B196 B208 to completely dimension a double rod preceding pages of this catalog. (See D KD B198 B212 cylinder. table at left.) After selecting necessary DD KDD† B198 B212 dimensions from that drawing, return On a double rod cylinder where the two to this page supplement the single rod rod ends are different, be sure to clearly *If only one end of these Double Rod Cylinders is to dimensions with those shown on drawings state which rod end is to be assembled be cushioned, be sure to specify clearly which end at right and dimension table below. Note at which end. Port position 1 is standard. this will be. that double rod cylinders have a head If other than standard, specify pos. 2, **Available in 7" bore, pages B190-B191. (Dim. G) at both ends and that dimension 3 or 4 when viewed from rod end #1 † Specify XI dimension from rod end #1. Mounting LD replace LB and ZL replaces ZB, etc. only. See port position information in the style KDD not available in 1" and 7" bore sizes. The double rod dimensions differ from, Engineering Section (Section A). All dimensions are in inches and apply to Code 1 rod sizes only. For alternate rod sizes, determine all envelope dimensions (within LD dim.) as described above and then use appropriate rod end dimensions for proper rod size from single rod cylinder. Add 2X Rod Add Stroke Stroke Rod Dia. Bore No. MM LD ZL SSK SNK ZM 1 1 1/2 4-3/4 5-1/2 3-3/8 2-1/8 6 1-1/2 1 5/8 4-7/8 5-3/4 3-3/8 2-1/4 6-1/8 2 1 5/8 4-7/8 5-13/16 3-3/8 2-1/4 6-1/8 2-1/2 1 5/8 5 5-15/16 3-1/2 2-3/8 6-1/4 3-1/4 1 1 6 7-1/8 3-3/4 2-5/8 7-1/2 4 1 1 6 7-1/8 3-3/4 2-5/8 7-1/2 5 1 1 6-1/4 7-7/16 3-5/8 2-7/8 7-3/4 6 1 1-3/8 7 8-5/16 4-1/8 3-1/8 8-3/4 7 1 1-3/8 7-1/8 — 4-1/4 3-1/4 8-7/8 8 1 1-3/8 7-1/8 — 4-1/4 3-1/4 8-7/8 10 1 1-3/4 8-1/8 — 4-7/8 4-1/8 10-3/8 12 1 2 8-5/8 — 5-3/8 4-5/8 11-1/8 14 1 2-1/2 10-1/8 — 6-3/8 5-1/2 13-1/8 Replaces: LB ZB SS SN — On single rod mounting styles: All Mtg. Styles C F All Mtgs. Parker Hannifin Corporation B174 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Options Series 2A/2AN C052 How To Order Parker “Style 55” Piston Rod End Rod end flange coupling for Parker Series 2A and 2AN Complete Model Number and place a “55” in the Pneumatic Cylinders: Piston Rod End designator position. n Simplifies alignment Example: 6.00J2AU155X12.000 Consult Factory for availability of mounting accessories n Reduces assembly time and Hardware. n Allows full rated pneumatic pressure in push and pull directions Dimensions Style 55 Rod End n Available in 5/8" through 5-1/2" piston rod diameters MM Rod Dia. AD AE AF AM WG 5/8 5/8 1/4 3/8 .57 1-3/4 1 15/16 3/8 11/16 .95 2-3/8 R 1/16 1-3/8 1-1/16 3/8 7/8 1.32 2-3/4 1-3/4 1-5/16 1/2 1-1/8 1.70 3-1/8 Ø AM Ø MM 2 1-11/16 5/8 1-3/8 1.95 3-3/4 2-1/2 1-15/16 3/4 1-3/4 2.45 4-1/2 Ø AF 3 2-7/16 7/8 2-1/4 2.95 4-7/8 3-1/2 2-11/16 1 2-1/2 3.45 5-5/8 AE G 4 2-11/16 1 3 3.95 5-3/4 AD F or RT DEPENDING 4-1/2 3-3/16 1-1/2 3-1/2 4.45 6-1/2 ON MOUNTING WG 5 3-3/16 1-1/2 3-7/8 4.95 6-5/8 Series 2A/2AN 5-1/2 3-15/16 1-7/8 4-3/8 5.45 7-1/2 See Cylinder Catalog for F, G and RT per bore and series. Split Couplers and Weld Plates C D ! WARNING: Piston rod separation from the machine F BOLTS member can result in severe personal injury or even death to nearby personnel. The cylinder user must make sure the weld holding the weld plate to the machine is of sufficient quality and size to hold the intended load. The cylinder user Ø E Ø A must also make sure the bolts holding split coupler to the Ø B weld plate are of sufficient strength to hold the intended load and installed in such a way that they will not become loose during the machine’s operation. STYLE 55 ROD END SPLIT COUPLER NOTE: Screws are not included with split coupler or weld plate. WELD PLATE Table 1 — Part Numbers and Dimensions Rod Bolt Split Coupler Weld Plate A B C D E F Bolt Size Dia. Circle Part No. Part No. 0.625 1.50 2.00 0.50 0.56 0.250 4 #10-24 x .94 LG 1.125 147234 0062 148174 0062 1.00 2.00 2.50 0.50 0.88 0.250 6 .250-20 x 1.25 LG 1.500 147234 0100 148174 0100 1.375 2.50 3.00 0.63 1.00 0.250 6 .312-18 x 1.50 LG 2.000 147234 0138 148174 0138 1.75 3.00 4.00 0.63 1.25 0.250 8 .312-18 x 1.75 LG 2.375 147234 0175 148174 0175 2.00 147234 0200 148174 0200 3.50 4.00 0.75 1.63 0.375 12 .375-16 x 2.25 LG 2.687 2.50 4.00 4.50 0.75 1.88 0.375 12 .375-16 x 2.50 LG 3.187 147234 0250 148174 0250 3.00 5.00 5.50 1.00 2.38 0.375 12 .500-13 x 3.25 LG 4.000 147234 0300 148174 0300 3.50 5.88 7.00 1.00 2.63 0.375 12 .625-11 x 3.50 LG 4.687 147234 0350 148174 0350 4.00 6.38 7.00 1.00 2.63 0.375 12 .625-11 x 3.50 LG 5.187 147234 0400 148174 0400 4.50 147234 0450 148174 0450 6.88 8.00 1.00 3.13 0.375 12 .625-11 x 4.00 LG 5.687 5.00 7.38 8.00 1.00 3.13 0.375 12 .625-11 x 4.00 LG 6.187 147234 0500 148174 0500 5.50 8.25 9.00 1.25 3.88 0.375 12 .750-10 x 5.00 LG 6.875 147234 0550 148174 0550 Parker Hannifin Corporation B175 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Options Series 2A/2AN C052 Cushion Length Adjustable Floating Cushions Cushions are optional, and can be supplied at head end, cap Cylinder Rod Cushion Length (Inches) end, or both ends without change in envelope or mounting Bore Diameter* Rod (Inches) (Inches) Number Head* Cap dimensions. All Parker cushions are adjustable. 5/8 1 7/8 13/16 The Series 2A cylinder design incorporates the longest 1-1/2 1 2 7/8 13/16 cushion sleeve and cushion spear that can be provided in the 5/8 1 7/8 13/16 standard envelope without decreasing the rod bearing and 2 1-3/8 2 7/8 13/16 piston bearing lengths. 5/8 1 7/8 13/16 2-1/2 (1) When a cushion is specified at the head end: 1-3/4 2 7/8 13/16 a. A self-centering sleeve is furnished on the piston rod 1 1 1-1/8 1 3-1/4 assembly. 2 2 13/16 1 1 1 1-1/8 1 b. A needle valve is provided that is flush with the side of 4 2-1/2 2 13/16 1 the head when wide open. It may be identified by the 1 1 1-1/8 1 fact that it is socket-keyed. It is located on side number 5 3-1/2 2 13/16 1 2, in all mounting styles except D, DB and DD. In these styles it is located on side number 3. Cylinder Rod Cushion Length (Inches) c. A springless check valve is provided that is also flush Bore Diameter* Rod with the side of the head and is mounted adjacent to (Inches) (Inches) Number Head* Cap the needle valve except on certain bores of mounting 13/8 1 1-3/8 1-1/4 style C where it is mounted opposite the needle valve. It 6 4 2 1-1/16 1-1/4 may be identified by the fact that it is slotted. 1-3/8 1 1-1/16 1-1/4 7 d. The check and needle valves are interchangeable in 2 4 1-1/16 1-1/4 the head. 1-3/8 1 1-1/16 1-1/4 8 (2) When a cushion is specified at the cap end: 5-1/2 2 1-5/16 1-1/4 1-3/4 1 1-5/16 1-3/4 a. A cushion spear is provided on the piston rod assembly. 10 5-1/2 0 1-3/16 1-3/4 b. A “float check” self-centering bushing is provided which 2 1 1-5/16 1-3/4 12 incorporates a large flow check valve for fast “out- 5-1/2 9 1-3/16 1-3/4 stroke” action. 2-1/2 1 1-3/4 2 14 c. A socket-keyed needle valve is provided that is flush 5-1/2 8 1-11/16 2 with the side of the cap when wide open. It is located on * Head end cushions for rod diameters not listed have cushion lengths side number 2 in all mounting styles except D, DB and with the limits shown. DD. In these styles it is located on side number 3. For cushion selection and sizing see Engineering Section. Parker Hannifin Corporation B176 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Options Series 2A/2AN C052 Non-Lube Air Cylinder (2AN) Today's industrial market demands more from a pneumatic In bore sizes to 12" diameter and rod diameters to 2-1/2", cylinder. Cylinders are still required to handle tough, heavy- the Parker Series 2AN air cylinder features rounded lip rod duty applications. But, more and more, these cylinders and piston seals. These seals glide over the PTFE based operate in environments or circumstances where it is lubricant that is provided at the time of manufacture. The not possible or advantageous to add lubrication to the Parker Series 2AN Non Lubricated Air Cylinder maintains the compressed air entering the cylinder. Certain packaging lubricant film where it belongs; on the seals bearing surfaces, and assembly operations, food environments, and piston rod and cylinder bore. microprocessor chip manufacturing are typical examples of Benefits include… long seal and bearing life. No oil needs areas where the exhausting of oil into the environment is not to be added through the use of lubricators. As the cylinder desirable. In many other situations, "non-lube" systems are strokes, no oil is expelled into the atmosphere with the used when proper air line lubrication is not present because exhaust air. of the time and expense of keeping lubricators filled and operating correctly. Piston Lipseals Gland Lipseals For Millions of Trouble Free Cycles Standard Specifications Anatomy of Series 2AN • Heavy Duty Service — ANSI/(NFPA) T3.6.7R2-1996 Sealing and Lubricant Retention Systems Specifications and Mounting Dimension Standards Increased heel thickness and Rounded sealing lip glides over outer lip extension improve lubricant film instead of scraping • NFPA Interchangeable stability, resist rolling. it off. Reduces friction, increases • 15 Standard Mounting Styles life and eliminates the need for added lubrication. • Strokes — Available in any Practical Stroke Length • Cushions — Optional at either end or both ends of stroke. “Float Check” at cap end. • Exceeds Automotive Specifications Drawing not to scale • Nominal Pressure – 250 PSI Air Service • Standard Temperature — -10°F to +165°F • Standard Fluid — Filtered Dry Air High integrity lubricant film with suspended PTFE particles In line with our policy of continuing product improvement, specifications in this catalog are subject to change. Available Bore and Rod Sizes* Bore Sizes Available 1-1/2" 2" 2-1/2" 3-1/4" 4" 5" 6" 8" 10" 12" 14" Rod Sizes Available 5/8" 1" 1-3/8" 1-3/4" 2" 2-1/2" 3" 3-1/2" 4" 4-1/2" 5" 5-1/2" *For specific cylinder bore size/piston rod availabilities and dimensions, see Series 2A Cylinder. Parker Hannifin Corporation B177 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Cylinder Accessories Series 2A/2AN C052 6 8 2 2 Female Rod Clevis 5 ➧ 3 4 Order to fit thread size. Cylinder Accessories Parker offers a complete range of cylinder accessories to assure you of 3 Knuckle (Female Rod Eye) greatest versatility in present or future cylinder applications. Rod End Accessories Accessories offered for the rod end of the cylinder include Rod Clevis, Eye Bracket, Knuckle, Clevis Bracket and Pivot Pin. To select the proper part number for any desired accessory, refer to Chart A below and look opposite the thread size of the rod end as indicated in the first ➧ column. The Pivot Pins, Eye Brackets and Clevis Brackets are listed opposite the thread size which their mating Knuckles or Clevises fit. Order to fit thread size. Mating Parts Mating Parts Thread Rod Eye Clevis Alignment Size Clevis Bracket Pin Knuckle Bracket Pin Coupler 4 Clevis Bracket for Knuckle 5/16-24 51221 74077 — 74075 74076 74078 134757 0031 7/16-20 50940 69195 68368 69089 69205 68368 134757 0044 1/2-20 50941 69195 68368 69090 69205 68368 134757 0050 3/4-16 50942 69196 68369 69091 69206† 68369 134757 0075 3/4-16 133284 69196 68369 69091 69206 68369 134757 0075 ➧ 7/8-14 50943 *85361 68370 69092 69207 68370 134757 0088 1-14 50944 *85361 68370 69093 69207 68370 134757 0100 1-14 133285 *85361 68370 69093 69207 68370 134757 0100 1-1/4-12 50945 69198 68371 69094 69208 68371 134757 0125 Order to fit Knuckle. 1-1/4-12 133286 69198 68371 69094 69208 68371 134757 0125 1-1/2-12 50946 *85362 68372 69095 69209 68372 133739 0150 1-3/4-12 50947 *85363 68373 69096 69210 69215 133739 0175 8 Mounting Plate or 5 Eye Bracket 1-7/8-12 50948 *85363 68373 69097 69210 69215 133739 0188 2-1/4-12 50949 *85364 68374 69098 69211 68374 2-1/2-12 50950 *85365 68375 69099 69212 68375 2-3/4-12 50951 *85365 68375 69100 69213 69216 Consult 3-1/4-12 50952 73538 73545 73536 73542 73545 Factory 3-1/2-12 50953 73539 73547 73437 73542 73545 4-12 50954 73539 73547 73438 73543 82181 ➧ 4-1/2-12 – – – 73439 73544 73547 †For alignment coupler dimensions, see Section C. *Cylinder accessory dimensions conform to NFPA recommended standard NFPA/T3.6.8 R1-1984, NFPA recommended standard fluid power systems — cylinder — dimensions for accessories for cataloged square head industrial types. Parker adopted this standard in April, 1985. Eye Brackets or Mounting Plates shipped before this 1. When used to mate with the Rod Clevis, select from Chart A. date may have different dimensions and will not necessarily interchange with the NFPA standard. For dimensional information on older style Eye Brackets or Mounting Plates consult Drawing #144805 or previous issues of this catalog. 2. When used to mount the Style BB cylinders, select from NOTE: For economical accessory selection, it is recommended that rod end style 4 be specified on your cylinder order. the Mounting Plate Selection Table. See Chart B at lower left. Accessory Load Capacity Chart B The various accessories on Pages B179 6 Pivot Pin and B180 have been load rated for your Mtg. Plate Series 2A convenience. The load capacity in lbs. shown Part No. Bore Size on page B179, is the recommended maximum ‡ 74076 1" load for that accessory based on a 4:1 design factor in tensions. (Pivot Pin is rated in shear.) 69195 1-1/2", 2", 2-1/2" Before specifying, compare the actual load or 69196 3-1/4", 4", 5" the tension (pull) force at maximum operating *85361 6", 7", 8" pressure of the cylinder with the load capacity ➧ of the accessory you plan to use. If load or 69198 10" pull force of cylinder exceeds load capacity of *85362 12" 1. Pivot Pins are furnished with Clevis Mounted Cylinders as accessory, consult factory. standard. *85363 14" 2. Pivot Pins are furnished with (2) Retainer Rings. ‡ Mounting plate for 1" bore single lug Mounting Plates BB cylinder mounting style is Clevis 3. Pivot Pins must be ordered as a separate item if to be used Mounting Plates for Style BB (Clevis mounted) Bracket P/N 74076. with Knuckles, Rod Clevises, or Clevis Brackets. cylinders are offered. To select proper part number for your application, refer to Chart B, above right. Parker Hannifin Corporation B178 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics CW CB CW ER +.004 CD +.002 CE A KK THREAD +.004 ER CD +.002 A FULL CD THREAD CD KK THREAD CD CA CB CW CB CW MR M 25 DD DIA + .004 CD 4 HOLES + .002 LR FL F R R E E CB MR M 25° DD DIA CD + .004 4 HOLES + .002 LR FL F R R E E CL +.001 CD –.002 Catalog 0900P-4 Heavy Duty Air Cylinders Cylinder Accessories Series 2A/2AN C052 Female Rod Clevis Part Number † 51221 50940 50941 50942 133284 50943 50944 133285 50945 133286 50946 50947 50948 50949 50950 50951 50952 50953 50954 ‡ ‡ ‡ A 13/16 3/4 3/4 1-1/8 1-1/8 1-5/8 1-5/8 1-5/8 1-7/8 2 2-1/4 3 3 3-1/2 3-1/2 3-1/2 3-1/2 4 4 CB 11/32 3/4 3/4 1-1/4 1-1/4 1-1/2 1-1/2 1-1/2 2 2 2-1/2 2-1/2 2-1/2 3 3 3 4 4-1/2 4-1/2 CD 5/16 1/2 1/2 3/4 3/4 1 1 1 1-3/8 1-3/8 1-3/4 2 2 2-1/2 3 3 3-1/2 4 4 CE 2-1/4 1-1/2 1-1/2 2-1/8 2-3/8 2-15/16 2-15/16 3-1/8 3-3/4 4-1/8 4-1/2 5-1/2 5-1/2 6-1/2 6-3/4 6-3/4 7-3/4 8-13/16 8-13/16 CW 13/64 1/2 1/2 5/8 5/8 3/4 3/4 3/4 1 1 1-1/4 1-1/4 1-1/4 1-1/2 1-1/2 1-1/2 2 2-1/4 2-1/4 ER 19/64 1/2 1/2 3/4 3/4 1 1 1 1-3/8 1-3/8 1-3/4 2 2 2-1/2 2-3/4 2-3/4 3-1/2 4 4 KK 5/16-24 7/16-20 1/2-20 3/4-16 3/4-16 7/8-14 1-14 1-14 1-1/4-12 1-1/4-12 1-1/2-12 1-3/4-12 1-7/8-12 2-1/4-12 2-1/2-12 2-3/4-12 3-1/4-12 3-1/2-12 4-12 Load Capacity 2600 4250 4900 11200 11200 18800 19500 19500 33500 33500 45600 65600 65600 98200 98200 98200 156700 193200 221200 Lbs. O Knuckle Part Number 74075 69089 69090 69091 69092 69093 69094 69095 69096 69097 69098 69099 69100 73536 73437 73438 73439 A 3/4 3/4 3/4 1-1/8 1-1/8 1-5/8 2 2-1/4 2-1/4 3 3-1/2 3-1/2 3-5/8 4-1/2 5 5-1/2 5-1/2 CA 1-1/2 1-1/2 1-1/2 2-1/16 2-3/8 2-13/16 3-7/16 4 4-3/8 5 5-13/16 6-1/8 6-1/2 7-5/8 7-5/8 9-1/8 9-1/8 CB 7/16 3/4 3/4 1-1/4 1-1/2 1-1/2 2 2-1/2 2-1/2 2-1/2 3 3 3-1/2 4 4 4-1/2 5 CD 7/16 1/2 1/2 3/4 1 1 1-3/8 1-3/4 2 2 2-1/2 3 3 3-1/2 3-1/2 4 4 ER 19/32 23/32 23/32 1-1/16 1-7/16 1-7/16 1-31/32 2-1/2 2-27/32 2-27/32 3-9/16 4-1/4 4-1/4 4-31/32 4-31/32 5-11/16 5-11/16 KK 5/16-24 7/16-20 1/2-20 3/4-16 7/8-14 1-14 1-1/4-12 1-1/2-12 1-3/4-12 1-7/8-12 2-1/4-12 2-1/2-12 2-3/4-12 3-1/4-12 3-1/2-12 4-12 4-1/2-12 Load Capacity 3300 5000 5700 12100 13000 21700 33500 45000 53500 75000 98700 110000 123300 161300 217300 273800 308500 Lbs.O Clevis Bracket for Knuckle Part Number 74076 69205 69206 69207 69208 69209 69210 69211 69212 69213 73542 73543 73544 CB 15/32 3/4 1-1/4 1-1/2 2 2-1/2 2-1/2 3 3 3-1/2 4 4-1/2 5 CD 7/16 1/2 3/4 1 1-3/8 1-3/4 2 2-1/2 3 3 3-1/2 4 4 CW 3/8 1/2 5/8 3/4 1 1-1/4 1-1/2 1-1/2 1-1/2 1-1/2 2 2 2 DD 17/64 13/32 17/32 21/32 21/32 29/32 1-1/16 1-3/16 1-5/16 1-5/16 1-13/16 2-1/16 2-1/16 E 2-1/4 3-1/2 5 6-1/2 7-1/2 9-1/2 12-3/4 12-3/4 12-3/4 12-3/4 15-1/2 17-1/2 17-1/2 F 3/8 1/2 5/8 3/4 7/8 7/8 1 1 1 1 1-11/16 1-15/16 1-15/16 FL 1 1-1/2 1-7/8 2-1/4 3 3-5/8 4-1/4 4-1/2 6 6 6-11/16 7-11/16 7-11/16 LR 5/8 3/4 1-3/16 1-1/2 2 2-3/4 3-3/16 3-1/2 4-1/4 4-1/4 5 5-3/4 5-3/4 M 3/8 1/2 3/4 1 1-3/8 1-3/4 2-1/4 2-1/2 3 3 3-1/2 4 4 MR 1/2 5/8 29/32 1-1/4 1-21/32 2-7/32 2-25/32 3-1/8 3-19/32 3-19/32 4-1/8 4-7/8 4-7/8 R 1.75 2.55 3.82 4.95 5.73 7.50 9.40 9.40 9.40 9.40 12.00 13.75 13.75 Load Capacity 3600 7300 14000 19200 36900 34000 33000 34900 33800 36900 83500 102600 108400 Lbs.O Eye Bracket and Mounting Plate Part Number 74077 69195 69196 85361* 69198 85362* 85363* 85364* 85365* 73538 73539 CB 5/16 3/4 1-1/4 1-1/2 2 2-1/2 2-1/2 3 3 4 4-1/2 CD 5/16 1/2 3/4 1 1- 3/8 1-3/4 2 2-1/2 3 3-1/2 4 DD 17/64 13/32 17/32 21/32 21/32 29/32 1-1/16 1-3/16 1-5/16 1-13/16 2-1/16 E 2-1/4 2-1/2 3-1/2 4-1/2 5 6-1/2 7-1/2 8-1/2 9-1/2 12-5/8 14-7/8 F 3/8 3/8 5/8 7/8 7/8 1-1/8 1-1/2 1-3/4 2 1-11/16 1-15/16 FL 1 1-1/8 1-7/8 2-3/8 3 3-3/8 4 4-3/4 5-1/4 5-11/16 6-7/16 LR 5/8 3/4 1-1/4 1-1/2 2-1/8 2-1/4 2-1/2 3 3-1/4 4 4-1/2 M 3/8 1/2 3/4 1 1-3/8 1-3/4 2 2-1/2 2-3/4 3-1/2 4 MR 1/2 9/16 7/8 1-1/4 1-5/8 2-1/8 2-7/16 3 3-1/4 4-1/8 5-1/4 R 1.75 1.63 2.55 3.25 3.82 4.95 5.73 6.58 7.50 9.62 11.45 Load Capacity 1700 4100 10500 20400 21200 49480 70000 94200 121900 57400 75000 Lbs.O Pivot Pin Part Number 74078 68368 68369 68370 68371 68372 68373 69215 68374 68375 69216 73545 82181 73547• CD 7/16 1/2 3/4 1 1-3/8 1-3/4 2 2 2-1/2 3 3 3-1/2 4 4 CL 1-5/16 1-7/8 2-5/8 3-1/8 4-1/8 5-3/16 5-3/16 5-11/16 6-3/16 6-1/4 6-3/4 8-1/4 8-5/8 9 Shear Capacity 6600 8600 19300 34300 65000 105200 137400 137400 214700 309200 309200 420900 565800 565800 Lbs.O *Cylinder accessory dimensions conform to NFPA recommended standard O See Accessory Load Capacity note on page B186. NFPA/T3.6.8 R1-1984, NFPA recommended standard fluid power systems — cylinder •These sizes supplied with cotter pins. — dimensions for accessor ies for cataloged square head industrial types. Parker adopted this standard in April, 1985. Eye Brackets or Mounting Plates shipped before †Includes Pivot Pin. this date may have different dimensions and will not necessarily interchange with the ‡Consult appropriate cylinder rod end dimensions for compatibility. NFPA standard. For dimensional information on older style Eye Brackets or Mounting Plates consult Drawing #144805 or previous issues of this catalog. Parker Hannifin Corporation B179 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Accessories / Spherical Bearing Mounting Series 2A/2AN C052 Parker offers a complete range of Cylinder Accessories to assure you of the greatest versatility in present or future cylinder applications. Accessories offered for the respective cylinder include the Rod Eye, Pivot Pin and Clevis Bracket. To select the proper part number for any desired accessory refer to the charts below. Spherical Rod Eye Bore Size Series 2A 1-1/2, 2 & 2-1/2 3-1/4, 4 & 5 6 & 8 10 12 14 Rod Eye Part No. 132290 132291 132292 132293 132294 132295 -.0005 -.0005 -.0005 -.0005 -.0005 -.0005 CD .5000 .7500 1.0000 1.3750 1.7500 2.0000 A 11/16 1 1-1/2 2 2-1/8 2-7/8 CE 7/8 1-1/4 1-7/8 2-1/8 2-1/2 2-3/4 EX 7-16 21-32 7/8 1-3/16 1-17/32 1-3/4 LUBE ER 13/16 1-1/8 1-1/4 1-11/16 2-1/16 2-1/2 FITTING LE 3/4 1-1/16 1-7/16 1-7/8 2-1/8 2-1/2 JK 7/16-20 3/4-16 1-14 1-1/4-12 1-1/2-12 1-7/8-12 JL 7/8 1-5/16 1-1/2 2 2-1/4 2-3/4 Load Capacity 2644 9441 16860 28562 43005 70193 Lbs. Order to fit Piston Rod Thread Size. Pivot Pin Bore Size Series 2A 1-1/2, 2 & 2-1/2 3-1/4, 4 & 5 6 & 8 10 12 14 Pivot Pin Part No. 83962 83963 83964 83965 83966 83967 -.0004 -.0005 -.0005 -.0006 -.0006 -.0007 CD .4997 .7497 .9997 1.3746 1.74960 1.9996 CL 1-9/16 2-1/32 2-1/2 3-5/16 4-7/32 4-15/16 Load Capacity 8600 19300 34300 65000 105200 137400 Lbs. Pivot Pins are furnished with (2) Retainer Rings. Clevis Bracket Bore Size Series 2A 1-1/2, 2 & 2-1/2 3-1/4, 4 & 5 6 & 8 10 12 14 Clevis Bracket Part No. 83947 83948 83949 83950 83951 83952 CD 1/2 3/4 1 1-3/8 1-3/4 2 CF 7/16 21/32 7/8 1-3/16 1-17/32 1-3/4 CW 1/2 5/8 3/4 1 1-1/4 1-1/2 DD 13/32 17-32 17/32 21/32 29/32 29/32 E 3 3-3/4 5-1/2 6-1/2 8-1/2 10-5/8 F 1/2 5/8 3/4 7/8 1-1/4 1-1/2 FL 1-1/2 2 2-1/2 3-1/2 4-1/2 5 LR 15/16 1-3/8 1-11/16 2-7/16 2-7/8 3-5/16 Order to fit Mounting Plate M 1/2 7/8 1 1-3/8 1-3/4 2 or Rod Eye. MR 5/8 1 1-3/16 1-5/8 2-1/16 2-3/8 R 2.05 2.76 4.10 4.95 6.58 7.92 Load Capacity 5770 9450 14300 20322 37800 50375 Lbs. Parker Hannifin Corporation B180 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics CD EX ER (MAX) LE CE A JK JL DIA THD CL CD CW CF CW MR M DD DIA + .004 CD 4 HOLES + .002 LR FL F R R E E Catalog 0900P-4 Heavy Duty Air Cylinders Service Kits Series 2A/2AN Seal Kits for Class 1 & 2 Service Series 2A (Class 1 Series 3L, 2H, VH RG RK Gland (Sym. 62) Rod Seal Cartridge Kits Kits Rod Contains Symbols Contains Symbols Gland Spanner Dia 14, 40, 41, 43 & 45 40, 41, 43 & 45 Wrench Wrench 1/2 RG2AHL 0051 RK2AHL 0051 069590 0000 011676 0000 5/8 RG2AHL 0061 RK2AHL 0061 069590 0000 011676 0000 1 RG2AHL 0101 RK2AHL 0101 069591 0000 011676 0000 1-3/8 RG2AHL 0131 RK2AHL 0131 069592 0000 011703 0000 1-3/4 RG2AHL 0171 RK2AHL 0171 069593 0000 011677 0000 2 RG2AHL 0201 RK2AHL 0201 069594 0000 011677 0000 2-1/2 RG2AHL 0251 RK2AHL 0251 069595 0000 011677 0000 3 RG2AHL 0301 RK2AHL 0301 069596 0000 011677 0000 3-1/2 RG2AHL 0351 RK2AHL 0351 069597 0000 011677 0000 4 RG2AHL 0401 RK2AHL 0401 069598 0000 011678 0000 4-1/2 RG2AHL 0451 RK2AHL 0451 083877 0000 011678 0000 5* RG2AHL 0501 RK2AHL 0501 069599 0000 011678 0000 5-1/2* RG2AHL 0551 RK2AHL 0551 069600 0000 011678 0000 *RG & RK kits listed are not applicable to 10" & 12" bore series 2H cylinders. See bulletin 0995-M4. PK/Piston Seal Kits Series Series 2A Only Bore Contains 2 Ea. Size Symbols: 42, 44 & 47 1 PK1002A001 1-1/2 PK1502A001 2 PK2002A001 2-1/2 PK2502A001 3-1/4 PK3202A001 4 PK4002A001 5 PK5002A001 6 PK6002A001 7 PK7002A001 8 PK8002A001 10 PK9002A001 12 PK9202A001 14 PK9402A001 CB Cylinder Body Seal Kits Bore Series 2A Series Size Contains 2 Ea. Symbol 47 1 CB102HL001 1-1/2 CB152HL001 2 CB202HL001 2-1/2 CB252HL001 3-1/4 CB322A0001 4 CB402A0001 5 CB502A0001 6 CB602A0001 7 CB702A0001 8 CB802A0001 10 CB902A0001 12 CB922A0001 14 – Parker Hannifin Corporation B181 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Service Kits Series 2A/2AN Seal Kits for Class 5 Service Series 2A, 2H, 3L & VH Cylinders RG RK Gland (Sym. 62) Rod Seal Cartridge Kits Kits Rod Contains Symbols Contains Symbols Gland Spanner Dia 14, 40, 41, 43 & 45 40, 41, 43 & 45 Wrench Wrench 1/2 RG2AHL 0055 RK2AHL 0055 069590 0000 011676 0000 5/8 RG2AHL 0065 RK2AHL 0065 069590 0000 011676 0000 1 RG2AHL 0105 RK2AHL 0105 069591 0000 011676 0000 1-3/8 RG2AHL 0135 RK2AHL 0135 069592 0000 011703 0000 1-3/4 RG2AHL 0175 RK2AHL 0175 069593 0000 011677 0000 2 RG2AHL 0205 RK2AHL 0205 069594 0000 011677 0000 2-1/2 RG2AHL 0255 RK2AHL 0255 069595 0000 011677 0000 3 RG2AHL 0305 RK2AHL 0305 069596 0000 011677 0000 3-1/2 RG2AHL 0355 RK2AHL 0355 069597 0000 011677 0000 4 RG2AHL 0405 RK2AHL 0405 069598 0000 011678 0000 4-1/2 RG2AHL 0455 RK2AHL 0455 083877 0000 011678 0000 5* RG2AHL 0505 RK2AHL 0505 069599 0000 011678 0000 5-1/2* RG2AHL 0555 RK2AHL 0555 069600 0000 011678 0000 *RG & RK kits listed are not applicable to 10" & 12" bore series 2H cylinders. See bulletin 0995-M4. PK/Piston Seal Kits Series Series 2A Only Bore Contains 2 Ea. Size Symbols: 42, 44 & 47 1 PK1002A005 1-1/2 PK1502A005 2 PK2002A005 2-1/2 PK2502A005 3-1/4 PK3202A005 4 PK4002A005 5 PK5002A005 6 PK6002A005 7 PK7002A005 8 PK8002A005 10 PK9002A005 12 PK9202A005 14 PK9402A005 CB Cylinder Body Seal Kits Bore Series 2A Series Size Contains 2 Ea. Symbol 47 1 CB102HL005 1-1/2 CB152HL005 2 CB202HL005 2-1/2 CB252HL005 3-1/4 4 5 6 Use (PK) Piston Seal Kits 7 for these Sizes 8 10 12 14 Parker Hannifin Corporation B182 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Service Kits Series 2A/2AN Seal Kits for 2AN & MAN PK CB Gland Cartridge Bore Piston Seal Kits Rod Spanner Wrenches Cylinder Body Seal Kits Wrenches Size for Series 2AN & MAN Dia. Part No. for Series 2AN & MAN Part No. Cylinders 1-1/2 PK1502 AN01 CB152H L001 5/8 069590 0000 011676 0000 2 PK2002 AN01 CB202H L001 1 069591 0000 011676 0000 2-1/2 PK2502 AN01 CB252H L001 1-3/8 069592 0000 011703 0000 3-1/4 PK3202 AN01 CB322A 0001 1-3/4 069593 0000 011677 0000 4 PK4002 AN01 CB402A 0001 2 069594 0000 011677 0000 5 PK5002 AN01 CB502A 0001 2-1/2 069595 0000 011677 0000 6 PK6002 AN01 CB602A 0001 3-1/2 069597 0000 011677 0000 7 PK7002 AN01 CB702A 0001 4 069598 0000 011678 0000 8 PK8002 AN01 CB802A 0001 4-1/2 083877 0000 011678 0000 10 PK9002 AN01 CB902A 0001 5* 069599 0000 011678 0000 12 PK9202 AN01 CB922A 0001 5-1/2* 069600 0000 011678 0000 14 PK9402 AN01 CB942A 0001 Parker Hannifin Corporation B183 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Heavy Duty Air Cylinders Notes Series 2A/2AN Parker Hannifin Corporation B184 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Pneumatic Actuator Products Safety Guide General Information Safety Guide for Selecting and Using Hydraulic, Pneumatic Cylinders and Their Accessories ! WARNING: FAILURE OF THE CYLINDER, ITS PARTS, ITS MOUNTING, ITS CONNECTIONS TO OTHER OBjECTS, OR ITS CONTROLS CAN RESULT IN: • Unanticipated or uncontrolled movement of the cylinder or objects connected to it. • Falling of the cylinder or objects held up by it. • Fluid escaping from the cylinder, potentially at high velocity. THESE EVENTS COULD CAUSE DEATH OR PERSONAL INjURY BY, FOR EXAMPLE, PERSONS FALLING FROM HIGH LOCATIONS, BEING CRUSHED OR STRUCK BY HEAVY OR FAST MOVING OBjECTS, BEING PUSHED INTO DANGEROUS EQUIPMENT OR SITUATIONS, OR SLIPPING ON ESCAPED FLUID. Before selecting or using Parker (The Company) cylinders or related accessories, • Unexpected detachment of the machine member from the piston rod. it is important that you read, understand and follow the following safety informa- • Failure of the pressurized fluid delivery system (hoses, fittings, valves, tion. Training is advised before selecting and using The Company’s products. pumps, compressors) which maintain cylinder position. 1.0 General Instructions • Catastrophic cylinder seal failure leading to sudden loss of pressurized fluid. 1.1 Scope – This safety guide provides instructions for selecting and using (including assembling, installing, and maintaining) cylinder products. This • Failure of the machine control system. safety guide is a supplement to and is to be used with the specific Company Follow the recommendations of the “Piston Rod Selection Chart and Data” publications for the specific cylinder products that are being considered for in the publication for the series of cylinders of interest. The suggested piston use. rod diameter in these charts must be followed in order to avoid piston rod 1.2 Fail Safe – Cylinder products can and do fail without warning for many buckling. reasons. All systems and equipment should be designed in a fail-safe mode Piston rods are not normally designed to absorb bending moments or loads so that if the failure of a cylinder product occurs people and property won’t which are perpendicular to the axis of piston rod motion. These additional be endangered. loads can cause the piston rod to fail. If these types of additional loads are expected to be imposed on the piston rod, their magnitude should be made 1.3 Distribution – Provide a free copy of this safety guide to each person known to our engineering department. responsible for selecting or using cylinder products. Do not select or use The Company’s cylinders without thoroughly reading and understanding this The cylinder user should always make sure that the piston rod is securely safety guide as well as the specific Company publications for the products attached to the machine member. considered or selected. On occasion cylinders are ordered with double rods (a piston rod extended 1.4 User Responsibility – Due to very wide variety of cylinder applications from both ends of the cylinder). In some cases a stop is threaded on to one and cylinder operating conditions, The Company does not warrant that of the piston rods and used as an external stroke adjuster. On occasions any particular cylinder is suitable for any specific application. This safety spacers are attached to the machine member connected to the piston rod guide does not analyze all technical parameters that must be considered and also used as a stroke adjuster. In both cases the stops will create a in selecting a product. The hydraulic and pneumatic cylinders outlined in pinch point and the user should consider appropriate use of guards. If these this catalog are designed to The Company’s design guidelines and do not external stops are not perpendicular to the mating contact surface, or if necessarily meet the design guideline of other agencies such as American debris is trapped between the contact surfaces, a bending moment will be Bureau of Shipping, ASME Pressure Vessel Code etc. The user, through its placed on the piston rod, which can lead to piston rod failure. An external own stop will also negate the effect of cushioning and will subject the piston rod analysis and testing, is solely responsible for: to impact loading. Those two (2) conditions can cause piston rod failure. Internal stroke adjusters are available with and without cushions. The • Making the final selection of the cylinders and related accessories. use of external stroke adjusters should be reviewed with our engineering • Determining if the cylinders are required to meet specific design department. requirements as required by the Agency(s) or industry standards covering The piston rod to piston and the stud to piston rod threaded connections the design of the user’s equipment. are secured with an anaerobic adhesive. The strength of the adhesive • Assuring that the user’s requirements are met, OSHA requirements are decreases with increasing temperature. Cylinders which can be exposed to met, and safety guidelines from the applicable agencies such as but not temperatures above +250°F (+121°C) are to be ordered with a non studded limited to ANSI are followed and that the use presents no health or safety piston rod and a pinned piston to rod joint. hazards. 2.3 Cushions – Cushions should be considered for cylinder applications • Providing all appropriate health and safety warnings on the equipment on when the piston velocity is expected to be over 4 inches/second. which the cylinders are used. Cylinder cushions are normally designed to absorb the energy of a linear 1.5 Additional Questions – Call the appropriate Company technical applied load. A rotating mass has considerably more energy than the same service department if you have any questions or require any additional mass moving in a linear mode. Cushioning for a rotating mass application information. See the Company publication for the product being considered should be review by our engineering department. or used, or call 1-800-CPARKER, or go to www.parker.com, for telephone numbers of the appropriate technical service department. 2.4 Cylinder Mountings – Some cylinder mounting configurations may have certain limitations such as but not limited to minimum stroke for side or 2.0 Cylinder and Accessories Selection foot mounting cylinders or pressure de-ratings for certain mounts. Carefully 2.1 Seals – Part of the process of selecting a cylinder is the selection of review the catalog for these types of restrictions. seal compounds. Before making this selection, consult the “seal information Always mount cylinders using the largest possible high tensile alloy steel page(s)” of the publication for the series of cylinders of interest. socket head cap screws that can fit in the cylinder mounting holes and The application of cylinders may allow fluids such as cutting fluids, wash torque them to the manufacturer’s recommendations for their size. down fluids etc. to come in contact with the external area of the cylinder. 2.5 Port Fittings – Hydraulic cylinders applied with meter out or These fluids may attack the piston rod wiper and or the primary seal and deceleration circuits are subject to intensified pressure at piston rod end. must be taken into account when selecting and specifying seal compounds. The rod end pressure is approximately equal to: Dynamic seals will wear. The rate of wear will depend on many operating factors. Wear can be rapid if a cylinder is mis-aligned or if the cylinder has operating pressure x effective cap end area been improperly serviced. The user must take seal wear into consideration effective rod end piston area in the application of cylinders. Contact your connector supplier for the pressure rating of individual 2.2 Piston Rods – Possible consequences of piston rod failure or connectors. separation of the piston rod from the piston include, but are not limited to are: 3.0 Cylinder and Accessories Installation and Mounting • Piston rod and or attached load thrown off at high speed. 3.1 Installation • High velocity fluid discharge. 3.1.1 – Cleanliness is an important consideration, and cylinders are shipped with the ports plugged to protect them from contaminants • Piston rod extending when pressure is applied in the piston retract mode. entering the ports. These plugs should not be removed until the piping is to be installed. Before making the connection to the cylinder ports, Piston rods or machine members attached to the piston rod may move N piping should be thoroughly cleaned to remove all chips or burrs which suddenly and without warning as a consequence of other conditions might have resulted from threading or flaring operations. occurring to the machine such as, but not limited to: Parker Hannifin Corporation N8 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Pneumatic Actuator Products Safety Guide General Information 3.1.2 – Cylinders operating in an environment where air drying damaged seals. Examine the piston rod for dents, gouges or score materials are present such as fast-drying chemicals, paint, or weld marks, and replace piston rod if surface is rough. splatter, or other hazardous conditions such as excessive heat, should Rod seal leakage could also be traced to gland wear. If clearance have shields installed to prevent damage to the piston rod and piston is excessive, replace rod bushing and seal. Rod seal leakage can rod seals. also be traced to seal deterioration. If seals are soft or gummy or brittle, check compatibility of seal material with lubricant used if 3.1.3 – Proper alignment of the cylinder piston rod and its mating air cylinder, or operating fluid if hydraulic cylinder. Replace with component on the machine should be checked in both the extended seal material, which is compatible with these fluids. If the seals and retracted positions. Improper alignment will result in excessive rod are hard or have lost elasticity, it is usually due to exposure to gland and/or cylinder bore wear. On fixed mounting cylinders attaching temperatures in excess of 165°F. (+74°C). Shield the cylinder the piston rod while the rod is retracted will help in achieving proper from the heat source to limit temperature to 350°F. (+177°C.) and alignment. replace with fluorocarbon seals. 3.1.4 – Sometimes it may be necessary to rotate the piston rod in 4.2.1.2 – Cylinder body seal leak can generally be traced to loose order to thread the piston rod into the machine member. This operation tie rods. Torque the tie rods to manufacturer’s recommendation for must always be done with zero pressure being applied to either side of that bore size. the piston. Failure to follow this procedure may result in loosening the piston to rod-threaded connection. In some rare cases the turning of Excessive pressure can also result in cylinder body seal leak. the piston rod may rotate a threaded piston rod gland and loosen it from Determine maximum pressure to rated limits. Replace seals and the retorque tie rods as in paragraph above. Excessive pressure cylinder head. Confirm that this condition is not occurring. If it does, can also result in cylinder body seal leak. Determine if the re-tighten the piston rod gland firmly against the cylinder head. pressure rating of the cylinder has been exceeded. If so, bring the operating pressure down to the rating of the cylinder and have the For double rod cylinders it is also important that when attaching or tie rods replaced. detaching the piston rod from the machine member that the torque be applied to the piston rod end of the cylinder that is directly attaching to Pinched or extruded cylinder body seal will also result in a leak. the machine member with the opposite end unrestrained. If the design Replace cylinder body seal and retorque as in paragraph above. of the machine is such that only the rod end of the cylinder opposite to Cylinder body seal leakage due to loss of radial squeeze which where the rod attaches to the machine member can be rotated, consult shows up in the form of flat spots or due to wear on the O.D. or the factory for further instructions. I.D. – Either of these are symptoms of normal wear due to high 3.2 Mounting Recommendations cycle rate or length of service. Replace seals as per paragraph above. 3.2.1 – Always mount cylinders using the largest possible high tensile alloy steel socket head screws that can fit in the cylinder mounting 4.2.2 – Internal Leakage holes and torque them to the manufacturer’s recommendations for their 4.2.2.1 – Piston seal leak (by-pass) 1 to 3 cubic inches per minute size. leakage is considered normal for piston ring construction. Virtually 3.2.2 – Side-Mounted Cylinders – In addition to the mounting bolts, no static leak with lipseal type seals on piston should be expected. cylinders of this type should be equipped with thrust keys or dowel pins Piston seal wear is a usual cause of piston seal leakage. Replace located so as to resist the major load. seals as required. 3.2.3 – Tie Rod Mounting – Cylinders with tie rod mountings are 4.2.2.2 – With lipseal type piston seals excessive back pressure recommended for applications where mounting space is limited. The due to over-adjustment of speed control valves could be a direct standard tie rod extension is shown as BB in dimension tables. Longer cause of rapid seal wear. Contamination in a hydraulic system or shorter extensions can be supplied. Nuts used for this mounting style can result in a scored cylinder bore, resulting in rapid seal wear. In should be torqued to the same value as the tie rods for that bore size. either case, replace piston seals as required. 3.2.4 – Flange Mount Cylinders – The controlled diameter of the rod 4.2.2.3 – What appears to be piston seal leak, evidenced by the gland extension on head end flange mount cylinders can be used fact that the cylinder drifts, is not always traceable to the piston. To as a pilot to locate the cylinders in relation to the machine. After make sure, it is suggested that one side of the cylinder piston be alignment has been obtained, the flanges may be drilled for pins or pressurized and the fluid line at the opposite port be disconnected. dowels to prevent shifting. Observe leakage. If none is evident, seek the cause of cylinder drift in other component parts in the circuit. 3.2.5 – Trunnion Mountings – Cylinders require lubricated bearing blocks with minimum bearing clearances. Bearing blocks should be 4.2.3 – Cylinder Fails to Move the Load carefully aligned and rigidly mounted so the trunnions will not be 4.2.3.1 – Pneumatic or hydraulic pressure is too low. Check the subjected to bending moments. The rod end should also be pivoted pressure at the cylinder to make sure it is to circuit requirements. with the pivot pin in line and parallel to axis of the trunnion pins. 4.2.3.2 – Piston Seal Leak – Operate the valve to cycle the 3.2.6 – Clevis Mountings – Cylinders should be pivoted at both ends cylinder and observe fluid flow at valve exhaust ports at end of with centerline of pins parallel to each other. After cylinder is mounted, cylinder stroke. Replace piston seals if flow is excessive. be sure to check to assure that the cylinder is free to swing through its working arc without interference from other machine parts. 4.2.3.3 – Cylinder is undersized for the load – Replace cylinder with one of a larger bore size. 4.0 Cylinder and Accessories Maintenance, Troubleshooting and Replacement 4.3 Erratic or Chatter Operation 4.1 Storage – At times cylinders are delivered before a customer is ready 4.3.1 – Excessive friction at rod gland or piston bearing due to load to install them and must be stored for a period of time. When storage is misalignment – Correct cylinder-to-load alignment. required the following procedures are recommended. 4.3.2 – Cylinder sized too close to load requirements – Reduce load or 4.1.1 – Store the cylinders in an indoor area which has a dry, clean and install larger cylinder. noncorrosive atmosphere. Take care to protect the cylinder from both 4.3.3 – Erratic operation could be traced to the difference between internal corrosion and external damage. static and kinetic friction. Install speed control valves to provide a back 4.1.2 – Whenever possible cylinders should be stored in a vertical pressure to control the stroke. position (piston rod up). This will minimize corrosion due to possible 4.4 Cylinder Modifications, Repairs, or Failed Component – Cylinders condensation which could occur inside the cylinder. This will also as shipped from the factory are not to be disassembled and or modified. minimize seal damage. If cylinders require modifications, these modifications must be done at 4.1.3 – Port protector plugs should be left in the cylinder until the time of company locations or by The Company’s certified facilities. The Cylinder installation. Division Engineering Department must be notified in the event of a 4.1.4 – If a cylinder is stored full of hydraulic fluid, expansion of the fluid mechanical fracture or permanent deformation of any cylinder component due to temperature changes must be considered. Installing a check (excluding seals). This includes a broken piston rod, tie rod, mounting valve with free flow out of the cylinder is one method. accessory or any other cylinder component. The notification should include all operation and application details. This information will be used to provide 4.1.5 – When cylinders are mounted on equipment that is stored an engineered repair that will prevent recurrence of the failure. outside for extended periods, exposed unpainted surfaces, e.g. It is allowed to disassemble cylinders for the purpose of replacing seals or piston rod, must be coated with a rust-inhibiting compound to prevent seal assemblies. However, this work must be done by strictly following all corrosion. the instructions provided with the seal kits. 4.2 Cylinder Trouble Shooting N 4.2.1 – External Leakage 4.2.1.1 – Rod seal leakage can generally be traced to worn or Parker Hannifin Corporation N9 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Catalog 0900P-4 Pneumatic Actuator Products Offer of Sale General Information Offer of Sale The items described in this document and other documents or descriptions provided by Parker Hannifin Corporation, its subsidiaries and Divisions (“Company”) and its authorized distributors, are hereby offered for sale at prices to be established by the Company, its subsidiaries and its authorized distributors. This offer and its acceptance by any customer (“Buyer”) shall be governed by all of the following Terms and Conditions. Buyer’s order for any such item, when communicated to the Company, its subsidiary or an authorized distributor (“Seller”) verbally or in writing, shall constitute acceptance of this offer. discard or otherwise dispose of any special tooling or other property in its 1. Terms and Conditions of Sale: All descriptions, quotations, proposals, sole discretion at any time. offers, acknowledgments, acceptances and sales of Seller’s products are subject to and shall be governed exclusively by the terms and conditions 8. Buyer’s Property: Any designs, tools, patterns, materials, drawings, stated herein. Buyer’s acceptance of any offer to sell is limited to these terms confidential information or equipment furnished by Buyer, or any other and conditions. Any terms or conditions in addition to, or inconsistent with items which become Buyer’s property, may be considered obsolete and those stated herein, proposed by Buyer in any acceptance of an offer by may be destroyed by Seller after two (2) consecutive years have elapsed Seller, are hereby objected to. No such additional, different or inconsistent without Buyer placing an order for the items which are manufactured using terms and conditions shall become part of the contract between Buyer and such property. Seller shall not be responsible for any loss or damage to Seller unless expressly accepted in writing by Seller. Seller’s acceptance such property while it is in Seller’s possession or control. of any offer to purchase by Buyer is expressly conditional upon Buyer’s 9. Taxes: Unless otherwise indicated on the face hereof, all prices and assent to all the terms and conditions stated herein, including any terms in charges are exclusive of excise, sales, use, property, occupational or like addition to, or inconsistent with those contained in Buyer’s offer. Acceptance taxes which may be imposed by any taxing authority upon the manufacture, of Seller’s products shall in all events constitute such assent. sale or delivery of the items sold hereunder. If any such taxes must be 2. Payment: Payment shall be made by Buyer net 30 days from the date of paid by Seller or if Seller is liable for the collection of such tax, the amount delivery of the items purchased hereunder. Amounts not timely paid shall thereof shall be in addition to the amounts for the items sold. Buyer agrees bear interest at the maximum rate permitted by law for each month or portion to pay all such taxes or to reimburse Seller therefore upon receipt of its thereof that the Buyer is late in making payment. Any claims by Buyer for invoice. If Buyer claims exemption from any sales, use or other tax imposed omissions or shortages in a shipment shall be waived unless Seller receives by any taxing authority, Buyer shall save Seller harmless from and against notice thereof within 30 days after Buyer’s receipt of the shipment. any such tax, together with any interest or penalties thereon which may be assessed if the items are held to be taxable. 3. Delivery: Unless otherwise provided on the face hereof, delivery shall be made F.O.B. Seller’s plant. Regardless of the method of delivery, 10. Indemnity For Infringement of Intellectual Property Rights: Seller however, risk of loss shall pass to Buyer upon Seller’s delivery to a carrier. shall have no liability for infringement of any patents, trademarks, copyrights, Any delivery dates shown are approximate only and Seller shall have no trade dress, trade secrets or similar rights except as provided in this Part 10. liability for any delays in delivery. Seller will defend and indemnify Buyer against allegations of infringement of U.S. patents, U.S. trademarks, copyrights, trade dress and trade secrets 4. Warranty: Seller warrants that the items sold hereunder shall be free (hereinafter “Intellectual Property Rights”). Seller will defend at its expense from defects in material or workmanship for a period of 18 months from and will pay the cost of any settlement or damages awarded in an action date of shipment from the Company. THIS WARRANTY COMPRISES brought against Buyer based on an allegation that an item sold pursuant THE SOLE AND ENTIRE WARRANTY PERTAINING TO ITEMS to this contract infringes the Intellectual Property Rights of a third party. PROVIDED HEREUNDER. SELLER MAKES NO OTHER WARRANTY, Seller’s obligation to defend and indemnify Buyer is contingent on Buyer GUARANTEE, OR REPRESENTATION OF ANY KIND WHATSOEVER. notifying Seller within ten (10) days after Buyer becomes aware of such ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO, allegations of infringement, and Seller having sole control over the defense MERCHANTABILITY AND FITNESS FOR PURPOSE, WHETHER of any allegations or actions including all negotiations for settlement or EXPRESS, IMPLIED, OR ARISING BY OPERATION OF LAW, TRADE compromise. If an item sold hereunder is subject to a claim that it infringes USAGE, OR COURSE OF DEALING ARE HEREBY DISCLAIMED. the Intellectual Property Rights of a third party, Seller may, at its sole NOTWITHSTANDING THE FOREGOING, THERE ARE NO WARRANTIES expense and option, procure for Buyer the right to continue using said WHATSOEVER ON ITEMS BUILT OR ACQUIRED WHOLLY OR item, replace or modify said item so as to make it noninfringing, or offer to PARTIALLY, TO BUYER’S DESIGN OR SPECIFICATIONS. accept return of said item and return the purchase price less a reasonable allowance for depreciation. Notwithstanding the foregoing, Seller shall 5. Limitation of Remedy: SELLER’S LIABILITY ARISING FROM OR IN have no liability for claims of infringement based on information provided ANY WAY CONNECTED WITH THE ITEMS SOLD OR THIS CONTRACT by Buyer, or directed to items delivered hereunder for which the designs SHALL BE LIMITED EXCLUSIVELY TO REPAIR OR REPLACEMENT are specified in whole or part by Buyer, or infringements resulting from the OF THE ITEMS SOLD OR REFUND OF THE PURCHASE PRICE PAID modification, combination or use in a system of any item sold hereunder. BY BUYER, AT SELLER’S SOLE OPTION. IN NO EVENT SHALL The foregoing provisions of this Part 10 shall constitute Seller’s sole and SELLER BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR exclusive liability and Buyer’s sole and exclusive remedy for infringement SPECIAL DAMAGES OF ANY KIND OR NATURE WHATSOEVER, of Intellectual Property Rights. INCLUDING BUT NOT LIMITED TO LOST PROFITS ARISING FROM OR IN ANY WAY CONNECTED WITH THIS AGREEMENT OR ITEMS If a claim is based on information provided by Buyer or if the design for an SOLD HEREUNDER, WHETHER ALLEGED TO ARISE FROM BREACH item delivered hereunder is specified in whole or in part by Buyer, Buyer OF CONTRACT, EXPRESS OR IMPLIED WARRANTY, OR IN TORT, shall defend and indemnify Seller for all costs, expenses or judgements INCLUDING WITHOUT LIMITATION, NEGLIGENCE, FAILURE TO WARN resulting from any claim that such item infringes any patent, trademark, OR STRICT LIABILITY. copyright, trade dress, trade secret or any similar right. 6. Changes, Reschedules and Cancellations: Buyer may request to modify 11. Force Majeure: Seller does not assume the risk of and shall not be the designs or specifications for the items sold hereunder as well as the liable for delay or failure to perform any of Seller’s obligations by reason quantities and delivery dates thereof, or may request to cancel all or part of circumstances beyond the reasonable control of Seller (hereinafter of this order, however, no such requested modification or cancellation shall “Events of Force Majeure”). Events of Force Majeure shall include without become part of the contract between Buyer and Seller unless accepted by limitation, accidents, acts of God, strikes or labor disputes, acts, laws, rules Seller in a written amendment to this Agreement. Acceptance of any such or regulations of any government or government agency, fires, floods, delays requested modification or cancellation shall be at Seller’s discretion, and or failures in delivery of carriers or suppliers, shortages of materials and shall be upon such terms and conditions as Seller may require. any other cause beyond Seller’s control. 7. Special Tooling: A tooling charge may be imposed for any special 12. Entire Agreement/Governing Law: The terms and conditions set tooling, including without limitations, dies, fixtures, molds and patterns, forth herein, together with any amendments, modifications and any acquired to manufacture items sold pursuant to this contract. Such special different terms or conditions expressly accepted by Seller in writing, shall tooling shall be and remain Seller’s property notwithstanding payment constitute the entire Agreement concerning the items sold, and there are of any charges by Buyer. In no event will Buyer acquire any interest in no oral or other representations or agreements which pertain thereto. apparatus belonging to Seller which is utilized in the manufacture of the This Agreement shall be governed in all respects by the law of the State items sold hereunder, even if such apparatus has been specially converted of Ohio. No actions arising out of sale of the items sold hereunder or this or adapted for such manufacture and notwithstanding any charges paid Agreement may be brought by either party more than two (2) years after by Buyer. Unless otherwise agreed, Seller shall have the right to alter, the cause of action accrues. N ©®2008 Parker Hannifin Corporation Printed in U.S.A. May, 2008 Parker Hannifin Corporation N10 Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics